Voltage Regulators

AN8000MS
Ripple filter IC for cellular phones

■ Overview +0.20
Unit: mm
2.80 –0.30
The AN8000MS is a ripple filter IC that rejects the +0.25
(0.65) 1.50 –0.05 (0.65)
ripple component superimposed on the regulator output.
Use for the VCO bias of cellular phones improves C/N

(1.45)
(0.95) (0.95)
and S/N and makes the high-quality telephone commu- 6 1

1.90±0.20
2.90 +0.20
–0.05
nication possible. Furthermore, by decreasing the differ-
5 2
ence between I/O voltages, drop in the power supply volt-
age of VCO is reduced. 4 3

0.30 +0.10
–0.05
■ Features

–0.06
0.16+0.10
• The I/O drop voltage is reduced to 0.3 V (A PNP tran-

–0.10
1.10+0.20

(0.80)
sistor is used for the pass transistor)
• The mounting area is reduced by adopting the mini-type

0 to 0.10
6-pin package 0.1 to 0.30
0.40±0.20

■ Applications MINI-6D
• Cellular phones and others

■ Block Diagram

4 1
VOUT VIN
Voltage control

2 Constant
C2 current

6
Switch On/Off

5 3
GND C1

Publication date: February 2002 SDH00013DEB 1

AN8000MS

■ Pin Descriptions
Pin No. Symbol Description
1 VIN Input pin
2 C2 Capacitor connection pin 2
3 C1 Capacitor connection pin 1
4 VOUT Output pin
5 GND Ground pin
6 On/Off Control pin

■ Absolute Maximum Ratings

Parameter Symbol Rating Unit
Supply voltage VIN 7.0 V
Supply current IIN 20 mA
Output current IO −15 mA
Allowable application voltage for VON/OFF VIN V
on/off pin
Allowable maximum capacitance for C1 pin C1 100 µF
Allowable maximum capacitance for C2 pin C2 10 µF
Power dissipation *2 PD 60 mW
Operating ambient temperature *1 Topr −25 to +75 °C
Storage temperature *1 Tstg −40 to +125 °C
Note) *1: Except for the operating ambient temperature and storage temperature, all ratings are for Ta = 25°C.
*2: The power dissipation shown is the value for Ta = 75°C.

■ Recommended Operating Range

Parameter Symbol Range Unit
Supply voltage VCC 2.5 to 6.5 V

■ Electrical Characteristics at Ta = 25°C

Parameter Symbol Conditions Min Typ Max Unit
Output voltage 1 VO1 VIN = 2.5 V, IOUT = −1 µA 2.10 2.27  V
Output voltage 2 VO2 VIN = 2.5 V, IOUT = −15 mA 1.95 2.14  V
Output voltage 3 VO3 VIN = 3.0 V, IOUT = −1 µA 2.60 2.79  V
Output voltage 4 VO4 VIN = 3.0 V, IOUT = −15 mA 2.60 2.66  V
Output voltage 5 VO5 VIN = 7.0 V, IOUT = −1 µA 6.70 6.87  V
Output voltage 6 VO6 VIN = 7.0 V, IOUT = −15 mA 6.60 6.74  V

2 SDH00013DEB
 AN8000MS

■ Electrical Characteristics at Ta = 25°C (continued)

Parameter Symbol Conditions Min Typ Max Unit
Consumption current 1 IO1 VIN = 2.5 V, IOUT = −1 µA −420 −322  µA
Consumption current 2 IO2 VIN = 2.5 V, IOUT = −15 mA −400 −304  µA
Consumption current 3 IO3 VIN = 3.0 V, IOUT = −1 µA −600 −490  µA
Consumption current 4 IO4 VIN = 3.0 V, IOUT = −15 mA −550 −450  µA
Consumption current 5 IO5 VIN = 7.0 V, IOUT = −1 µA −2.0 −1.5  mA
Consumption current 6 IO6 VIN = 7.0 V, IOUT = −15 mA −2.0 −1.7  mA
Load regulation 1 REGL1 VIN = 2.5 V, IOUT = −1 µA to −15 mA 0 134 200 mV
Load regulation 2 REGL2 VIN = 3.0 V, IOUT = −1 µA to −15 mA 0 122 200 mV
Load regulation 3 REGL3 VIN = 7.0 V, IOUT = −1 µA to −15 mA 0 126 200 mV
Consumption current against IREG1 VIN = 2.5 V, IOUT = −1 µA to −15 mA −100 −18 100 µA
load change 1
Consumption current against IREG2 VIN = 3.0 V, IOUT = −1 µA to −15 mA −100 −18 100 µA
load change 2
Consumption current against IREG3 VIN = 7.0 V, IOUT = −1 µA to −15 mA −150 −5 150 µA
load change 3
Ripple rejection ratio 1 RR1 VIN = 3 V ± 0.15 V, IOUT = −15 mA, 20 23  dB
f = 1 kHz
Ripple rejection ratio 2 RR2 VIN = 3 V ± 0.15 V, IOUT = −15 mA, 35 40  dB
f = 25 kHz
Ripple rejection ratio 3 RR3 VIN = 3 V ± 0.15 V, IOUT = −15 mA, 30 36  dB
f = 100 kHz

■ Application Notes
1. PD  Ta curves of MINI-6D package
PD  T a

140

120 Independent IC
without a heat sink
Power dissipation PD (W)

PD = 120 mW (25°C)
100
Independent IC
without a heat sink
80 PD = 60 mW (75°C)

60

40

20

0
0 25 50 75 100 125 150

Ambient temperature Ta (°C)

SDH00013DEB 3
AN8000MS

■ Application Notes (continued)

2. Main characteristics
RR  Ta Output voltage  Ta
45 2.7
VIN = 3.0 V
40 IOUT = 15 mA
Ripple rejection ratio RR (dB)

2.68
35

Output voltage (V)

30
2.66
25

20
2.64
f = 25 kHz
15 f = 100 kHz
f = 1 kHz
10 2.62
VIN = 3.0 V
5
IOUT = 15 mA
0 2.6
−25 0 25 50 75 −25 0 25 50 75

Ambient temperature Ta (°C) Ambient temperature Ta (°C)

RR  frpl

40
Ripple rejection ratio RR (dB)

35

30

25
65°C
20 25°C
−25°C
15

10

0
100 1k 10k 100k

Ripple frequency frpl (Hz)

3. Transient response
1) Test circuit and conditions
Input
4.7 µF 0.1 µF
3.6 V
Reg.
4 700 pF
3V
Input
1 2 3
SYNPWRR On

AN8000MS 0V

6 5 4 Output
Output V-out
0V
SYNPWRR On 270 Ω

0.015 µF

4 SDH00013DEB
 2) Transient characteristics (SYNPWR, VOUT)

Ta = −25°C Total Leading edge Falling edge

(V) (V) (V)
3 3 3

2 2 2

1 1 1

SYNPWR

SYNPWR
SYNPWR
0 0 0

3 3 3

2 2 2

VOUT
3. Transient response (continued)

VOUT
VOUT
■ Application Notes (continued)

1 1 1

0 0 0
2 ms/div. 10 µs/div. 10 µs/div.

Ta = 25°C (V) (V) (V)

3 3 3

2 2 2

1 1 1

SYNPWR
SYNPWR

SYNPWR

SDH00013DEB
0 0 0

3 3 3

2 2 2

VOUT
VOUT

VOUT
1 1 1

0 0 0
2 ms/div. 10 µs/div. 10 µs/div.

Ta = 65°C
(V) (V) (V)
3 3 3

2 2 2

1 1 1

SYNPWR

SYNPWR
SYNPWR

0 0 0

3 3 3

2 VOUT 2 2

VOUT
VOUT

1 1 1

0 0 0
2 ms/div. 10 µs/div. 10 µs/div.
AN8000MS

5
AN8000MS

■ Application Circuit Examples

1. Application system example
The ripple component super-
imposed on the regulator out-
put is rejected.

Voltage of Ripple filter

battery Regulator VCO
AN8000MS

PLL

2. Application circuit example

VOUT 4 1 VIN
0.015 µF

Voltage control

4.7 µF
C2 2 Constant
Load
current

6 On/Off
Switch
0.1 µF

5 3
4 700 pF

GND C1

3. PCB pattern
AN8000MS

1 6

6 SDH00013DEB
Request for your special attention and precautions in using the technical information
and semiconductors described in this material
(1) An export permit needs to be obtained from the competent authorities of the Japanese Govern-
ment if any of the products or technologies described in this material and controlled under the
"Foreign Exchange and Foreign Trade Law" is to be exported or taken out of Japan.
(2) The technical information described in this material is limited to showing representative character-
istics and applied circuit examples of the products. It does not constitute the warranting of industrial
property, the granting of relative rights, or the granting of any license.
(3) The products described in this material are intended to be used for standard applications or gen-
eral electronic equipment (such as office equipment, communications equipment, measuring in-
struments and household appliances).
Consult our sales staff in advance for information on the following applications:
• Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment,
combustion equipment, life support systems and safety devices) in which exceptional quality and
reliability are required, or if the failure or malfunction of the products may directly jeopardize life or
harm the human body.
• Any applications other than the standard applications intended.
(4) The products and product specifications described in this material are subject to change without
notice for reasons of modification and/or improvement. At the final stage of your design, purchas-
ing, or use of the products, therefore, ask for the most up-to-date Product Standards in advance to
make sure that the latest specifications satisfy your requirements.
(5) When designing your equipment, comply with the guaranteed values, in particular those of maxi-
mum rating, the range of operating power supply voltage and heat radiation characteristics. Other-
wise, we will not be liable for any defect which may arise later in your equipment.
Even when the products are used within the guaranteed values, redundant design is recommended,
so that such equipment may not violate relevant laws or regulations because of the function of our
products.
(6) When using products for which dry packing is required, observe the conditions (including shelf life
and after-unpacking standby time) agreed upon when specification sheets are individually exchanged.
(7) No part of this material may be reprinted or reproduced by any means without written permission
from our company.

Please read the following notes before using the datasheets

A. These materials are intended as a reference to assist customers with the selection of Panasonic
semiconductor products best suited to their applications.
Due to modification or other reasons, any information contained in this material, such as available
product types, technical data, and so on, is subject to change without notice.
Customers are advised to contact our semiconductor sales office and obtain the latest information
before starting precise technical research and/or purchasing activities.
B. Panasonic is endeavoring to continually improve the quality and reliability of these materials but
there is always the possibility that further rectifications will be required in the future. Therefore,
Panasonic will not assume any liability for any damages arising from any errors etc. that may ap-
pear in this material.
C. These materials are solely intended for a customer's individual use.
Therefore, without the prior written approval of Panasonic, any other use such as reproducing,
selling, or distributing this material to a third party, via the Internet or in any other way, is prohibited.

2001 MAR