DXM1200 BX

Sure Cross® DXM1200-Bx Wireless
Controller
Instruction Manual
Original Instructions
216539 Rev. F
10 November 2021
© Banner Engineering Corp. All rights reserved
216539
Sure Cross® DXM1200-Bx Wireless Controller
Contents
1 DXM1200-Bx System Overview .................................................................................................................................... 4
1.1 DXM1200 Models .............................................................................................................................................................................6
1.2 DXM Hardware Configuration Overview .......................................................................................................................................... 6
1.3 DXM Automation Protocols ..............................................................................................................................................................7
1.4 DXM Modbus Overview ................................................................................................................................................................... 7
1.4.1 DXM Modbus Registers ...........................................................................................................................................................8
1.5 DXM Configuration Software ............................................................................................................................................................9
1.6 Dimensions .................................................................................................................................................................................... 10
2 Quick Start Guide ........................................................................................................................................................ 11
2.1 Device Setup .................................................................................................................................................................................11
2.1.1 Apply Power to the Controller ................................................................................................................................................11
2.1.2 Binding and Conducting a Site Survey with the ISM Radio ...................................................................................................11
2.1.3 Set a Static IP Address ...........................................................................................................................................................13
2.2 Configuration Instructions ............................................................................................................................................................. 14
2.2.1 Configuring the DXM1200 Controller ......................................................................................................................................14
2.2.2 Configuration Example: Reading Registers on a Modbus Slave Device ...............................................................................14
3 ISM Radio Board (Slave ID 1) .....................................................................................................................................17
3.1 MultiHop Radio DIP Switches ........................................................................................................................................................ 17
3.1.1 Application Mode .................................................................................................................................................................... 18
3.1.2 Baud Rate and Parity ............................................................................................................................................................. 18
3.1.3 Disable Serial ......................................................................................................................................................................... 18
3.1.4 Transmit Power Levels/Frame Size ........................................................................................................................................19
3.2 Modbus Registers for the MultiHop Radio Board Module .............................................................................................................. 19
3.3 DIP Switch Settings for the Performance Gateway Radio Module ................................................................................................ 19
3.4 Modbus Registers for the Performance Gateway Radio Module ................................................................................................... 20
3.4.1 Alternative Modbus Register Organization ............................................................................................................................. 21
4 Processor Connections .............................................................................................................................................. 24
4.1 DIP Switch Settings for the Base Board ........................................................................................................................................25
4.2 Ethernet .........................................................................................................................................................................................25
4.3 USB ...............................................................................................................................................................................................25
4.4 Internal Local Registers (Slave ID 199) for the DXM700, DXM1000, and DXM1200 .................................................................... 26
4.5 Modbus RTU Master ......................................................................................................................................................................29
5 Cellular Modem Boards ...............................................................................................................................................30
5.1 Cellular Modem Board for GSM and LTE ...................................................................................................................................... 30
5.2 Cellular Power Requirements ........................................................................................................................................................ 30
5.3 Using the DXM Cellular Modem .....................................................................................................................................................30
5.3.1 Activating a Cellular Modem ...................................................................................................................................................30
6 LCD and Menu System ................................................................................................................................................35
6.1 Registers .......................................................................................................................................................................................35
6.2 Push ..............................................................................................................................................................................................35
6.3 ISM Radio ..................................................................................................................................................................................... 36
6.4 System Config ................................................................................................................................................................................36
6.4.1 ISM Radio ..............................................................................................................................................................................37
6.4.2 Ethernet ................................................................................................................................................................................. 37
6.4.3 LCD Contrast .........................................................................................................................................................................37
6.4.4 Reset ..................................................................................................................................................................................... 37
6.5 System Info ................................................................................................................................................................................... 38
6.6 Display Lock ..................................................................................................................................................................................39
6.7 Modbus Registers for the LCD (Modbus Slave ID 201) ................................................................................................................. 39
7 Working with Modbus Devices ...................................................................................................................................40
7.1 Assigning Modbus Slave IDs ........................................................................................................................................................ 40
7.2 Modbus Operation .........................................................................................................................................................................41
7.3 Wireless and Wired Devices ......................................................................................................................................................... 41
7.4 Modbus Communication Timeouts ................................................................................................................................................41
7.4.1 MultiHop Networks vs DX80 Star Networks .......................................................................................................................... 41
7.4.2 Calculating the Communications Timeout for Battery-Powered MultiHop Radios ..................................................................42
7.4.3 Calculating the Communication Timeout for 10–30 VDC MultiHop Radios ............................................................................42
7.4.4 Adjusting the Receive Slots and Retry Count Parameters .................................................................................................... 42
7.4.5 Calculating the Communication Timeout for a DX80 Star Network ........................................................................................43
7.5 Modbus TCP Client .......................................................................................................................................................................43
8 Configuration Instructions .........................................................................................................................................44
8.1 Scheduler ......................................................................................................................................................................................44
8.1.1 Create a Weekly Event ..........................................................................................................................................................44
8.1.2 Create a One-Time Event ......................................................................................................................................................44

8.1.3 Create a Holiday Event ..........................................................................................................................................................45
8.2 Authentication Setup .....................................................................................................................................................................45
8.2.1 Set the Controller to use Authentication ................................................................................................................................ 45
8.2.2 Controller Configuration Authentication .................................................................................................................................46
8.3 Register Flow and Configuration ...................................................................................................................................................47
8.3.1 Basic Approach to Configuration ........................................................................................................................................... 47
8.3.2 Troubleshooting a Configuration ........................................................................................................................................... 47
8.3.3 Saving and Loading Configuration Files ................................................................................................................................47
8.3.4 Uploading or Downloading Configuration Files ..................................................................................................................... 48
8.4 EtherNet/IP™ Configuration ........................................................................................................................................................... 48
8.4.1 Configuring the Host PLC ......................................................................................................................................................48
8.4.2 Configuring the Controller ......................................................................................................................................................48
8.5 Setting up Email and Text Messaging ...........................................................................................................................................49
8.5.1 Mail Server Authentication .....................................................................................................................................................49
8.5.2 Define the Network Interface Settings ................................................................................................................................... 50
8.5.3 Configure your Ethernet Connection ..................................................................................................................................... 50
8.5.4 Configure your Cellular Connection .......................................................................................................................................51
8.5.5 Set the Email and Messaging Parameters ............................................................................................................................ 51
8.5.6 Define Threshold Rules for Email ..........................................................................................................................................52
8.5.7 Define Log File Parameters for Emailing Log Files ............................................................................................................... 52
8.6 Ethernet and Cellular Push Retries ...............................................................................................................................................53
8.6.1 Ethernet Push Retries ........................................................................................................................................................... 53
8.6.2 Cellular Push Retries .............................................................................................................................................................53
8.6.3 Event/Action Rule or Log File Push Retries .......................................................................................................................... 53
8.6.4 Email and Text Message Push Retries ................................................................................................................................. 54
9 PROFINET® ................................................................................................................................................................. 55
9.1 General Station Description Markup Language File ..................................................................................................................... 55
9.2 DXM PROFINET IO Data Model ...................................................................................................................................................55
9.3 Configure the DXM Controller for a PROFINET IO Connection ....................................................................................................55
9.3.1 Save and Upload the Configuration File ................................................................................................................................55
9.4 Slots and Modules .........................................................................................................................................................................56
9.5 Configuration Instructions ............................................................................................................................................................. 57
9.5.1 Install the GSD File ................................................................................................................................................................57
9.5.2 Change the Device IP Address ............................................................................................................................................. 59
9.5.3 Change the Device Name ..................................................................................................................................................... 60
10 Accessories ................................................................................................................................................................62
11 Product Support and Maintenance ......................................................................................................................... 63
11.1 File System and Archive Process ............................................................................................................................................... 63
11.2 Update Your DXM Processor Firmware Using the DXM Configuration Tool .............................................................................. 64
11.3 Clear the Password on DXM700-Bx, DXM1000-Bx, or DXM1200-Bx Models ............................................................................64
11.4 DXM1200 Documentation ...........................................................................................................................................................64
11.5 DXM1200 Support Policy ............................................................................................................................................................65
11.5.1 Firmware Updates ............................................................................................................................................................... 65
11.5.2 Website Information .............................................................................................................................................................65
11.5.3 Feature Requests ................................................................................................................................................................ 65
11.5.4 Potential DXM Issues .......................................................................................................................................................... 65
11.5.5 DXM Security .......................................................................................................................................................................65
11.6 Contact Us ................................................................................................................................................................................... 65
11.7 Mexican Importer ......................................................................................................................................................................... 66
11.8 ..................................................................................................................................................................................................... 66
11.9 FCC and ISED Certification, 900 MHz, 1 Watt Radios ................................................................................................................ 66
11.10 FCC and ISED Certification, 2.4GHz ......................................................................................................................................... 67
11.11 Warnings ....................................................................................................................................................................................68
11.12 Banner Engineering Corp. Limited Warranty ............................................................................................................................ 69
1 DXM1200-Bx System Overview

Banner's DXM Logic Controller integrates Banner's wireless radio and cellular connectivity to provide a platform for the
Industrial Internet of Things (IIoT).
Figure 1. DXM1200 system overview
I/O Connectivity Logic Controller User Interface

N/A Cellular Action Rules LCD Screen
Sure Cross® Radios Programming Language LED Indicators
Ethernet Scheduler
Internal Micro USB Push to the Cloud
RS-485 Master Data Logging
Email
Table 1: Modbus registers for internal local registers (Modbus slave ID 199)
Local Registers Type Description
1–845 32-bit integer Local data registers
846–849 32-bit integer Reset, Constant, Timer
851–900 32-bit non-volatile integer Data flash, non-volatile
901–1000 Reserved for internal use
1001–5000 Floating point Floating point registers, local data registers
> 10000 Read only virtual registers, system-level data
Figure 2. DXM1200 Controller Figure 3. DXM1200E Controller
M12 D-Code for Ethernet

Antenna
Connection Antenna
Connection
M12 Courtesy
Power Out
and RS-485
M12 Power
and RS-485
M8 Connection
Ethernet
M12 Power Connection
4 www.bannerengineering.com - Tel: + 1 888 373 6767

Connectivity—The DXM1200's wired and wireless connectivity options make it easy to share data between local and remote
equipment. The cellular modem option eliminates the need for IT infrastructures to connect remote equipment for sensing
and control to IIoT cloud services. The integrated Sure Cross® wireless radio enables Modbus connectivity to remote
sensors, indicators, and control equipment. Connect directly to any PLC and/or SCADA system for easy integration into
existing control or monitoring systems. Banner Industrial Wireless radios have two types of networks that can be used for
creating applications and solving problems.
Wired Connectivity Wireless Connectivity

Ethernet: Modbus/TCP (master/slave) or Ethernet/IP Sure Cross Wireless Radio: DX80 900 MHz, DX80
Field Bus: Modbus RS-485 Master 2.4 GHz, MultiHop 900 MHz, or MultiHop 2.4 GHz
Cellular modem: LTE (United States only) or GSM
(Outside the United States), CATM1-ATT (North
America Only) or CATM1-VZW (US Only)
Wireless Radio Networks
Performance Wireless Radio Network MultiHop Wireless Radio Network

Star topology (point to point between Gateway and Tree topology between one master radio and many
Node radios) repeater and/or slave radios
Battery-powered Node applications are more efficient Repeater radios add effectively unlimited radio
in a star topology network range
Six inputs and six outputs maximum per radio Full Modbus sensor register data collection as well as
typical local I/O like discrete, analog, etc.
Logic Controller—Program the DXM1200's logic controller using action rules and/or ScriptBasic language, which can
execute concurrently. The control functions allow freedom when creating custom sensing and control sequences. The logic
controller supports the Modbus protocol standards for data management, ensuring seamless integration with existing
automation systems. File and LCD password protection is an option.
Register Mapping Scheduler

Cyclical Read rules from wireless devices or local Time/calendar-based events
wired Modbus devices that include optional scaling, Holiday skips
error conditions, and the ability to activate a read rule
One-time events
Cyclical or Change of State Write rules to wireless
Dynamic scheduler updating
devices or local wired Modbus devices with scaling
Astronomical clock
Modbus/TCP Master Read or Write rules for external
devices on the network Optional Text Programming Language
Action Rules ScriptBasic to create variables, arrays, functions,
loops, IF/THEN/ELSE, logical and arithmetic
Thresholds (IF/THEN/ELSE) with timers, minimum
operators, API commands, register access, string
on/off time, and logging options
functions and operators, time commands
Math/Logic Rules (arithmetic and bitwise operators)
Data Logging
Control Logic (logical operators and SR/T/D/JK flip
flops) Cyclic data/event logging
Trending (multiple averaging filters) Email log files
Tracking (counts, on/off times)
Email notifications
Push data on conditions
User Interface— A simple user interface consists of an LCD screen and four LED indicators.
www.bannerengineering.com - Tel: + 1 888 373 6767 5

User programmable LCD API Interface

Bind Sure Cross radios Host Initiated control
Conduct a site survey to evaluate the radio signal Web service integration
integrity of radios within the network User Defined LED indicators
View register and output information Indicates the status of the DXM1200, processes, or
View system status and configuration equipment
1.1 DXM1200 Models

Base Base Radio Configuration
DXM1200 – B1 R1
Blank = Low profile housing Blank = None

One 4-pin M8 Ethernet connector R1 = 900 MHz, 1 W PE5 Performance Radio (North America)
One 5-pin M12 power and RS-485 connector R2 = 900 MHz, 1 W HE5 MultiHop Data Radio (North America)
E = Extended housing R3 = 2.4 GHz, 65 mW PE5 Performance Radio (Worldwide)
One 4-pin M12 D Code Ethernet connector R4 = 2.4 GHz, 65 mW HE5 MultiHop Data Radio (Worldwide)
One 5-pin M12 power and RS-485 connector
Two 5-pin M12 RS-485 connectors
B1 = Modbus controller for data aggregation of

sensors and wireless networks
Power: 12−30 V DC
Comms: RS-485
Figure 4. DXM1200-B1 model Figure 5. DXM1200E-B1 model
1.2 DXM Hardware Configuration Overview

The DXM1200-Bx Wireless Controller can have multiple configurations. The DXM1200 will have a model number label on the
housing. Use the model number and model table above to identify which boards are included in the controller.
When opening the DXM1200, follow proper ESD grounding procedures.
Important:
• Electrostatic discharge (ESD) sensitive device
• ESD can damage the device. Damage from inappropriate handling is not covered by warranty.
• Use proper handling procedures to prevent ESD damage. Proper handling procedures include
leaving devices in their anti-static packaging until ready for use; wearing anti-static wrist straps; and
assembling units on a grounded, static-dissipative surface.
The top housing contains the LCD display board. The display board is connected to the base board using a ribbon cable with
a 20-pin connector.

Figure 6. DXM1200 base board
Cellular Antenna Placement
Cell Modem
SIM card*
location Micro USB
Antenna Cable
ISM
Radio
Board
*SIM card is located on the underside of installed modem
1.3 DXM Automation Protocols

The DXM1200 supports the following automation protocols.
Modbus RTU
The DXM1200 manages separate physical ports running the Modbus RTU protocol. The DXM1200 is the Modbus
Master when operating the Modbus master RTU port. The DXM1200 uses the master Modbus RTU bus to
communicate with locally connected Modbus devices or uses the Banner wireless radio to communicate with remote
Modbus devices.
Modbus TCP/IP
A host system acting as a Modbus master can access the DXM1200 using the Modbus TCP/IP protocol over
Ethernet. Standard Modbus port 502 is used by the DXM1200 for all Modbus TCP/IP requests.
All internal registers are available to the host system concurrently with Modbus RTU.
By default, Modbus TCP/IP master is active. If you are using the DXM as a Modbus TCP master, configure the
DXM1200 using Modbus TCP rules in the DXM Configuration Software.
EtherNet/IP™
The Ethernet port is actively running EtherNet/IP. From the factory, the DXM1200 is configured to read and write
registers on DX80 wireless devices 1 through 16. Custom individual local register configurations can be set with the
Protocol Conversion field in the DXM Configuration Software.
By default, EtherNet/IP is active.
EtherNet/IP registers are limited to 228 registers set as E/IP Originator to DXM and 228 registers set as DXM to
Originator.
1.4 DXM Modbus Overview

The DXM1200 uses internal 32-bit registers to store information. The processor's internal Local Registers serve as the main
global pool of registers and are used as the common data exchange mechanism. External Modbus device registers can be
read into the Local Registers or written from the local data registers.
The DXM1200, as a Modbus master device, exchanges data using the Local Registers. Modbus over Ethernet (Modbus/
TCP) uses the Local Registers as the accessible register data.

Using Action, Read/Write, and Threshold Rules allows you to manipulate the processor's Local Registers. The ScriptBasic
programming capabilities extends the use of Local Registers with variables to create a flexible programming solution for more
complex applications.
The processor's Local Registers are divided into three different types: integer, floating point, and non-volatile. When using
Local Registers internally, the user can store 32-bit numbers. Using Local Registers with external Modbus devices follows the
Modbus standard of a 16-bit holding register. Local Registers are accessible as Modbus ID 199.
Accessing the I/O Base and the LCD follows the same communication as an external Modbus device. Each device has an ID
number to uniquely identify itself. The LCD is Modbus ID 201.
Figure 7. DXM1200 Modbus overview
Processor/Outputs (Base Board)

Local Registers
(Modbus ID 199) ISM Radio (Modbus ID 1)
Ethernet Local Regi sters Gateway or MultiHop

Integer
Local Registers User Display (Modbus ID 201)
RS-485 (master) Float
LED / LCD Display
Local Registers
Non-Volatile
Internal
Micro USB
Processor Controlled
Cellular Modem
Modbus Data Traffic

Control
1.4.1 DXM Modbus Registers

The DXM1200-Bx Wireless Controller may have up to three internal Modbus slave devices:
Table 2: DXM internal Modbus slave IDs (factory default)
Modbus Slave ID Device
1 DX80 Performance Gateway or MultiHop ISM Radio—MultiHop wireless devices connected to the internal MultiHop radio
should be assigned Modbus Slave addresses starting at 11.
199 Local Registers—Internal storage registers of the DXM1200
201 LCD—The user has access to the LED indicators on the DXM1200.
All Modbus registers are defined as 16-bit Modbus Holding Registers. When connecting external Modbus slave devices, only
use Modbus slave IDs 2 through 198. The Modbus IDs for the local registers, LCD, and ISM radio are fixed.

Table 4: Modbus registers for the LCD board (Modbus slave ID 201)
Modbus Register LED Color State
1102 : bit 0 LED 1 Red
1103 : bit 0 LED 2 Green

1 = On
1104 : bit 0 LED 3 Blue
0 = Off
1105: bit 0 LED 4 Amber
1105: bit 0 Backlight
Modbus Registers for the ISM Radio (Modbus Slave ID 1)—See Modbus Registers for the MultiHop Radio Board Module
on page 19 and Modbus Registers for the Performance Gateway Radio Module on page 20.
1.5 DXM Configuration Software

Download the latest version of all configuration software from http://www.bannerengineering.com. For more information on
using the DXM Configuration Software, refer to the instruction manual (p/n 209933).
The DXM Configuration Software configures the DXM1200 by creating an XML file that is transferred to the DXM1200 using
an Ethernet connector or the internal micro USB connection. The DXM1200 can also receive the XML configuration file from
a Web server using a cellular or Ethernet connection.
Figure 8. Overview of the DXM Configuration Software features
DXM Configuration Software
Local Registers
Register Mapping
Action Rules
Scheduler
Script Basic
System Register
Settings View Utility
Internal Micro
USB
XML Config File Ethernet
This configuration file governs all aspects of the DXM1200 operation.

The wireless network devices are a separate configurable system. Use the DX80 User Configuration Software to configure
the internal DX80 wireless Gateway and the attached wireless Nodes. Use the MultiHop Configuration Software if the internal
radio is a MultiHop device.
All tools can be connected to the DXM1200 using an Ethernet connection or the internal micro USB.

1.6 Dimensions
All measurements are listed in millimeters, unless noted otherwise.
Figure 9. DXM1200 dimensions
14.9 mm
[0.58”]
11.2 mm
[0.44”]
7.1 mm (4)
[0.28”]
55.9 mm 50.8 mm
[2.2”] [2”]
1/4-20 (2)
Threaded insert
130.4 mm [5.13”]
140.8 mm [5.54”]
148.1 mm [5.83”]
170.5 mm [6.71”]
147.9 mm [5.82”]
90.8 mm 53.8 mm
[3.57”] 68.9 mm [2.12”]
45.4 mm [2.71”] 33.8 mm
[1.79”] [1.33”]
30.5 mm 8.7 mm 35.5 mm

[1.2”] [0.34”] [1.4”]
Figure 10. DXM1200E dimensions
7.1 mm dia (2)

[0.28”]
17.5 mm
[0.69”]
27.9 mm
M12 x 1
[1.1”]
73.3 mm
[2.89”]
83.7 mm 27.9 mm
[3.3”] [1.1”] PG9 (2)
9.7 mm 148.1 mm
[0.38”] [5.83”]
180.9 mm
90.8 mm 9.3 mm [7.12”] 100.1 mm
[3.57”] [0.36”] [4”]
135 mm
[5”]
45.4 mm
130.4 mm [1.79”]
[5.13”]
M12 x 1
55.22 mm
[2.17”]
34.5 mm
[1.36”] 25.4 mm
[1”] 20.1 mm [0.79”]
25.4 mm [1”]

2 Quick Start Guide

2.1 Device Setup
2.1.1 Apply Power to the Controller

Follow these instructions to apply 12–30 V DC power to the controller using a wall plug.
Equipment used:
• DXM1200
• PSW-24-1 DC power supply with multi-blade wall plug, 100–240 V AC 50/60 Hz input, 24 V DC 1 A output, UL Listed
Class 2, 4-pin female M12 connector
Table 5: 5-pin M12 male connector wiring
5-pin M12 Male Connector Pin Wire Color Description
1 Brown (bn) 10 to 30 V DC
1 2 White (wh) RS485 / D1 / B / +

2
3 Blue (bu) DC common (GND)
4
3 5 4 Black (bk) RS485 / D0 / A / –
5 Gray (gy) Comms Ground
Important:
• Never operate a 1 Watt radio without connecting an antenna
• Operating 1 Watt radios without an antenna connected will damage the radio circuitry.
• To avoid damaging the radio circuitry, never apply power to a Sure Cross® Performance or Sure
Cross MultiHop (1 Watt) radio without an antenna connected.
1. Connect the PSW-24-1 power supply into the DXM Controller, aligning the keys in the connector, and hand tighten.
2. Plug the PSW-24-1power supply into a power outlet using the appropriate regional wall adapter.
2.1.2 Binding and Conducting a Site Survey with the ISM Radio
Before the ISM radio can communicate, the ISM radio within the DXM must be bound to the other radios in the wireless
network.
Use the DXM LCD menu to bind external radios to the internal ISM radio.
If you are having difficulty running binding or site surveys, it may be because of the speed of the XML configuration file or
script running on the DXM. To resolve this issue, try one of the following options:
• Disable the XML and script by setting DIP switch 4 on the processor board to ON and cycling the power to the DXM.
After binding the devices, turn DIP switch 4 back OFF and cycle power again to return to normal operation of the XML
and script.
• Adjust the XML or script to slow down the RTU read or write rules.
• Upload a blank XML, bind all devices, then upload the configured XML file.

Bind a DX80 Node to a DXM and Assign the Node Address

Binding Nodes to a Gateway ensures the Nodes only exchange data with the Gateway they are bound to. After a Gateway
enters binding mode, the Gateway automatically generates and transmits a unique extended addressing (XADR), or binding,
code to all Nodes within range that are also in binding mode. The extended addressing (binding) code defines the network,
and all radios within a network must use the same code.
1. Apply power to all the devices.
Separate radios by two meters when running the binding procedure. Put only one DXM Gateway into binding mode at
a time to prevent binding to the wrong Gateway.
2. Enter binding mode on the DXM radio:
a) Use the arrow keys to select the ISM Radio menu on the LCD and press ENTER.
b) Highlight the Binding menu and press ENTER.
3. Assign the Node address to the Node.
• For Nodes without rotary dials: Use the DXM arrow keys to select the Node address to assign to the DX80 Node
about to enter binding mode. The DXM assigns this Node address to the next Node that enters binding mode.
Only bind one Node at a time.
• For Nodes with rotary dials: Use the Node's rotary dials to assign a valid decimal Node Address (between 01 and
47). The left rotary dial represents the tens digit (0 through 4) and the right dial represents the ones digit (0
through 9) of the Node Address. You can leave the DXM "Bind to" address set to 1 because the Node's rotary
dials will override that setting.
4. Start binding mode on the DXM radio by pressing ENTER on the DXM radio.
5. Enter binding mode on the DX80 Node.
• For housed radios, triple-click button 2.
• For board-level radios, triple-click the button.
• For Nodes without buttons, refer to the Node's datasheet for instructions on entering binding mode.
The left and right LEDs flash alternately and the Node searches for a Gateway in binding mode. After the Node binds,
the LEDs stay solid momentarily, then they flash together four times. The Node automatically exits binding mode and
reboots.
6. Label the Node with the assigned address number for future reference.
7. Press BACK on the DXM to exit binding mode for that specific Node address.
The Node LEDs continue to flash red until the DXM exits binding mode with that Node address.
8. Repeat these steps for as many DX80 Nodes as are needed for your network.
9. When you are finished binding, press BACK on the DXM until you return to the main menu.
Bind a MultiHop Radio to a DXM and Assign the Device ID

Before beginning the binding procedure, apply power to all the devices. Separate radios by two (2) meters when running
binding procedure. Put only one DXM MultiHop master radio into binding mode at a time to prevent binding the slave radios
to the wrong master radio.
Binding MultiHop radios ensures all MultiHop radios within a network communicate only with other radios within the same
network. The MultiHop radio master automatically generates a unique binding code when the radio master enters binding
mode. This code is then transmitted to all radios within range that are also in binding mode. After a repeater/slave is bound,
the repeater/slave radio accepts data only from the master to which it is bound. The binding code defines the network, and all
radios within a network must use the same binding code.
1. Enter binding mode on the DXM radio:
a) Use the arrow keys select the ISM Radio menu on the LCD and press ENTER.
b) Highlight the Binding menu and press ENTER.
2. Assign the device address to the repeater or slave radios. Valid device IDs are 11 through 60.
• For MultiHop radios without rotary dials: Use the DXM arrow keys to select the device ID to assign to the MultiHop
radio about to enter binding mode. The DXM assigns this device ID to the next radio that enters binding mode.
Only bind one slave radio at a time.
• For MultiHop radios with rotary dials: Use the MultiHop radio's rotary dials to assign a device ID . The left rotary
dial represents the tens digit (1 through 6) and the right dial represents the ones digit (0 through 9) of the device
ID. You can leave the DXM "Bind to" address set to 1 because the MultiHop's rotary dials will override that setting.
3. Start binding mode on the DXM radio by pressing ENTER on the DXM radio.
4. After entering binding mode on the DXM, put the MultiHop repeater or slave radio into binding mode.
• For housed radios, triple-click button 2.
• For board-level radios, triple-click the button.
• For radios without buttons, refer to the radio's datasheet for instructions on entering binding mode.
After binding is completed, the MultiHop radio automatically exits binding mode and begins operation.

5. Press BACK on the DXM to exit binding mode for that specific device address.
The Multihop radio's LEDs continue to flash red until the DXM exits binding mode with that MultiHop radio.
6. Label the MultiHop radio with the assigned address number for future reference.
7. Repeat these steps, changing the device address, for as many MultiHop radios as are needed for your network.
8. When you are finished binding, press BACK on the DXM until you return to the main menu.
All radio devices begin to form the network after the master data radio exits binding mode.
Conduct a Site Survey from the DXM

Conduct a Site Survey to verify the wireless communication between the radios within your wireless network. Conduct the
site survey when the Nodes and DXM Controller are at the proposed installation sites to determine each radio's signal
strength with the DXM.
For a DX80 network, the Gateway controls the site survey and the results display on the LCD. Running a site survey on a
DX80 network does not affect the throughput of the DX80 network. The DX80 Gateway-Node system can run a site survey
analysis while the network is operational. For a MulitHop network, the master device passes the site survey request to the
intended Modbus slave device. The Site Survey runs and the results display on the LCD. Running a site survey on a
MultiHop network stops all network traffic to that device.
1. On the DXM: Use the arrow buttons to select the ISM Radio menu and press ENTER.
2. Select the Site Survey menu and press ENTER.
3. Use the Up or Down arrows to select the device ID number and press ENTER to run the site survey with that radio.
The site survey results display as green, yellow, red, and missed packets. Green indicates the highest signal
strength, then yellow, and red. Missed packets were not received.
4. When you are finished running the Site Survey, press Back twice to return to the main menu and exit site survey
mode.
If the Site Survey fails (100 missed packets), verify the radios are at least 10 feet from the DXM and/or rerun the binding
procedure. If you find poor signal quality, common solutions include moving the DXM to a more central location relative to the
Nodes or using higher-gain antennas on the DXM. Contact your local Banner Engineering representative for assistance.
2.1.3 Set a Static IP Address

Change the IP address of the DXM to connect to a local area network, Modbus TCP/IP host controller, or EtherNet/IP host
controller.
There are two ways to set the IP address: using the DXM's LCD menu or using the configuration software to change the XML
file. IP addresses entered into the LCD menu system override the IP addresses in the XML configuration files. To use the IP
addresses set in the XML configuration file, clear the IP addresses from the menu system.
Figure 11. System Config menu options
System Config Ethernet DHCP Update DHCP Mode

IP: Update IP Address ↑ ↓ to change the value
SN: Update SN ENTER to accept
After making changes to the GW: Update GW Address
Ethernet settings, restart the DXM. Reset Resets Ethernet parameters BACK to return to the previous menu
to xml defaults.
1. On the DXM, use the arrows and move to the System Config menu. Press ENTER.
2. Use the arrow keys to select the Ethernet menu. Press ENTER.
3. Highlight the DHCP selection and press ENTER. Set DHCP to OFF.
4. The system will request a restart, press ENTER to confirm.
5. Follow steps 1 and 2 to reenter the Ethernet menu. Use the arrow keys to select IP. Press ENTER.
The IP address displays (for example, 192.168.0.1).
6. Use the up and down arrows to change the IP address. Press ENTER to move to the next octet.
7. Press ENTER on the final octet to accept the changes.
8. Cycle power to the DXM.
The changes are saved on the DXM and the new IP address will be used.
Use this same procedures to set the subnet mask (SN) and default gateway (GW) to match your network requirements. Your
IT department can provide these settings if needed.

2.2 Configuration Instructions
2.2.1 Configuring the DXM1200 Controller

Configure the DXM1200 using the configuration software.
The DXM Configuration Software allows the user to define parameters for the DXM1200, then saves the configuration in an
XML file on the PC.
Figure 12. DXM Configuration Software
DXM Configuration Software
Local Registers
Register Mapping
Action Rules
Scheduler
Script Basic
System Register
Settings View Utility
Internal Micro
USB
XML Config File Ethernet
To configure the DXM1200, connect the provided M8-to-Ethernet cable to both the DXM1200 and a computer or local area
network. The computer and DXM must have IP addresses from the same network. After the configuration file is saved,
upload the XML configuration file to the DXM1200 for operation.
This quick start guide outlines the basic operations to set up a DXM1200 using the configuration software. For a more
comprehensive explanation of features, refer to the DXM Configuration Software Instruction Manual (p/n 209933).
For a complete list of all associated product documentation, go to Product Support and Maintenance on page 63.
2.2.2 Configuration Example: Reading Registers on a Modbus Slave

Device
The opening page of the DXM Configuration Software displays the Local Registers tab. The local registers are the main
global pool of registers that are defined by the user to store data within the DXM1200. The bottom status bar displays the
communications status, application status, and the DXM Configuration Software version.
In this short example, we will configure the DXM1200 to read six registers on an external Modbus Slave device and save the
data into the local registers.

Step 1: Define the Local Registers

Change the name and parameter settings for each Local Register under the Local Registers in Use screen. You may
change them individually (Edit Register) or in groups (Modify Multiple Registers).
Figure 13. Modify Multiple Registers - Configuration Example
1. Click on the Modify Multiple Registers section of the Local Registers in Use screen. Use this screen to quickly
modify multiple local registers at a time.
2. Select the range of registers to change.
3. Select the fields to change in each local register. In our example, registers one through six will be changed and the
names will be GPS Reg followed by an auto-incremented number. This example will also change the LCD
permissions flag to Set, then Read to allow the values of the local registers to display on the LCD.
4. Click Modify Registers to apply your changes.
Step 2: Read the Registers

Under Register Mapping, the Read Rules or Write Rules interact with the Local Registers to exchange data with external
Modbus devices.
Figure 14. Read Rules - Configuration Example
This example screen shows a read rule created to read six registers (address 1 through 6), from Modbus Slave 4. The results
are stored in the Local Registers 1 through 6.
1. Go to the Register Mapping > RTU or Modbus TCP > Read Rules tab to define a Modbus read rule.
2. Click Add Read Rule.
3. Click the arrow next to the new rule to display all parameters.
4. Type in a name into the name field.
5. Select the slave address. In this example, we will read from Slave ID 4.
6. Select the starting register and ending register. In this example, we will read from register 1 through register 6.
7. Select the beginning local register on the DXM1200.
8. Enter a polling frequency. In this example we have entered five seconds.
9. If necessary, select the error condition. For this example, if the read function fails after three attempts, the read rule
writes 12345 to the DXM1200 local registers. Notice the list of local register names this read rule is using.

Step 3: Define the Time Zone and Set the Time Clock
Use the Settings > System screen to define the time zone and daylight saving option. The time zone and DST options are
saved into the configuration file.
Figure 15. Settings > System > Device Time
If you connect the DXM1200 to a computer, click Sync PC Time with Device to set the time on the DXM1200 to match the
time of the computer.
Step 4: Save the Configuration File

To save your configuration file:
1. Go to File > Save As.
2. Enter a file name and save the file. The file name cannot contain spaces or special characters.
Step 5: Connect the DXM1200

1. Connect the DXM1200 to the computer using the supplied M8 to RJ45 cable. This is an Ethernet connection.
2. From the Device menu, select Connection Settings.
3. From the dialog box, select TCP/IP and enter the IP address of the DXM connected to the computer or local area
network. Select Serial if you are connecting to the DXM using the internal micro USB.
4. Click Connect to connect to the DXM1200.
Figure 16. Connection settings pop-up window
Step 6: Send the Configuration File to the DXM1200

1. From the Device menu, select Send XML Configuration to Device.
2. Select the configuration file to load. The software will have pre-selected the file name you have previously saved.
Important: The software only loads a file to the DXM1200. Internal parameter settings that are changed in
the tool but not saved to the file will not be sent to the device.
After the file is selected, the software uploads the file to the DXM1200. The DXM Configuration Software reboots the
controller after the configuration file finishes uploading. The new configuration is only read at startup and always requires a
reboot or power cycle to take effect. It will take a few seconds for the DXM1200 to reboot.
Important: If the power cycles to the DXM1200 while the DXM Configuration Software is connected, close
the USB port from the software and unplug the USB cable. Reconnect the DXM1200 by plugging the USB
cable into the DXM1200, then select Device > Connection Settings.
The DXM1200 is now running the new configuration. On the DXM1200's LCD screen, select the Registers menu by clicking
the Enter button with the Registers menu highlighted. The local registers defined in the configuration tool display.

3 ISM Radio Board (Slave ID 1)

Plug the ISM radio into the I/O base board with the U.FL antenna connector closest to the SMA connectors. Typically, users
will not need to adjust the DIP switch settings on the physical radio modules.
For the DXM1200 models, set the radio options using the LCD menu.
Figure 17. ISM radio board
Antenna
4
LED
3 2 1
3 2 1
ON
ON
DIP Switch DIP Switch Button

Bank 1 Bank 2
Button Operation
For DXM models without a LCD display, use the button to bind the ISM radio. For models with a LCD display, use
the ISM menu to bind the radio.
LED Operation
The LED located on the ISM radio module indicates power and communications traffic. ISM board LED operations
also display on the LED on the right side of the I/O base board.
• Solid green DX80 ISM radio LED indicates power.
• Flashing green MultiHop ISM radio LED indicates operation.
• Red and green combined: Communications traffic and binding.
3.1 MultiHop Radio DIP Switches

MultiHop ISM radio devices are defined with R2, R4, and R5 in the model number.
• DXMxxx-xxR2 - MultiHop 900 MHz
• DXMxxx-xxR4 - MultiHop 2.4 GHz
• DXMxxx-xxR5 - MultiHop 900 MHz, 100 mW
• DXMxxx-xxR9 - MultiHop 900 MHz, (Australia)
Making changes to the baud or parity settings requires that you make the same settings to the Modbus Master
Communications section within the DXM Configuration Software (Settings > General.
Important: Disabling the serial port disables the ISM radio in the DXM1200. Selecting Transparent mode
causes radio communications to be slower and denies access to device I/O register data.

Table 6: DIP switch settings
D1 Switches D2 Switches
Device Settings 1 2 3 4 1 2 3 4
Serial line baud rate 19200 OR User defined receiver OFF* OFF*
slots
Serial line baud rate 38400 OR 32 receiver slots OFF ON
Serial line baud rate 9600 OR 128 receiver slots ON OFF
Serial line baud rate Custom OR 4 receiver slots ON ON
Parity: None OFF* OFF*
Parity: Even OFF ON
Parity: Odd ON OFF
Disable serial (low power mode) and enable the receiver ON ON

slots select for switches 1-2
Transmit power OFF

900 MHz radios: 1.00 Watt (30 dBm)
2.4 GHz radios: 0.065 Watts (18 dBm) and 60 ms
frame
Transmit power ON *
900 MHz radios: 0.25 Watts (24 dBm)
2.4 GHz radios: 0.065 Watts (18 dBm) and 40 ms
frame
Application mode: Modbus OFF*
Application mode: Transparent ON
MultiHop radio setting: Repeater OFF OFF
MultiHop radio setting: Master OFF ON
MultiHop radio setting: Slave ON OFF
MultiHop radio setting: DXM LCD Menu Control ON * ON *
* Default configuration. The default settings for D2 DIP switches 1, 3, and 4 are ON. This allows for forcing the device into
Master mode and DXM menu control for the radio power settings.
3.1.1 Application Mode

The MultiHop radio operates in either Modbus mode or transparent mode. Use the internal DIP switches to select the mode
of operation. All MultiHop radios within a wireless network must be in the same mode.
Modbus mode uses the Modbus protocol for routing packets. In Modbus mode, a routing table is stored in each parent
device to optimize the radio traffic. This allows for point to point communication in a multiple data radio network and
acknowledgement/retry of radio packets. To access a radio's I/O, the radios must be running in Modbus mode.
In transparent application mode, all incoming packets are stored, then broadcast to all connected data radios. The data
communication is packet based and not specific to any protocol. The application layer is responsible for data integrity. For
one to one data radios it is possible to enable broadcast acknowledgement of the data packets to provide better throughput.
In transparent mode, there is no access to the radio's I/O.
3.1.2 Baud Rate and Parity

The baud rate (bits per second) is the data transmission rate between the device and whatever it is physically wired to. Set
the parity to match the parity of the device you are wired to.
3.1.3 Disable Serial

Disable an unused local serial connection to reduce the power consumption of a data radio powered from the solar assembly
or from batteries. All radio communications remain operational.

3.1.4 Transmit Power Levels/Frame Size

The 900 MHz data radios can be operated at 1 watt (30 dBm) or 0.250 watt (24 dBm). For most models, the default transmit
power is 1 watt.
For 2.4 GHz radios, the transmit power is fixed at 0.065 watt (18 dBm) and DIP switch 5 is used to set the frame timing. The
default position (OFF) sets the frame timing to 60 milliseconds. To increase throughput, set the frame timing to 40
milliseconds. For battery-powered devices, increasing the throughput decreases battery life.
Important: Prior to date code 15341 and radio firmware version 3.6, the frame timing was 40 ms (OFF) or
20 ms (ON).
3.2 Modbus Registers for the MultiHop Radio Board Module

The DX80 MultiHop master radio is a tree-based architecture device that allows for repeater radios to extend the wireless
network. Each device in a MultiHop network is a Modbus device with a unique Modbus ID.
Modbus registers in a MultiHop network are contained within each individual radio device. To obtain Modbus register data
from a MultiHop device, configure the DXM1200 to access each device across the wireless network as an individual Modbus
slave device.
Table 7: Example MultiHop Modbus registers with generic devices.
MulitHop Device Slave ID Modbus Registers
DXM Master radio 1 none
Slave radio 11 Modbus register 1–16 are inputs, 501–516 are outputs
Repeater radio 12 Modbus register 1–16 are inputs, 501–516 are outputs
Slave radio 15 Modbus register 1–16 are inputs, 501–516 are outputs
3.3 DIP Switch Settings for the Performance Gateway Radio Module
The 900 MHz radios transmit at 1 Watt (30 dBm) or 250 mW (24 dBm). The 250 mW mode reduces the radio's range but
improves the battery life in short range applications. For 2.4 GHz models, this DIP switch is disabled. The transmit power for
2.4 GHz is fixed at about 65 mW EIRP (18 dBm).
DX80 Performance Gateway ISM radio devices are defined with R1, R3, and R8 in the model number.
• DXMxxx-xxR1 - DX80 Performance 900MHz
• DXMxxx-xxR3 - DX80 Performance 2.4GHz
• DXMxxx-xxR8 - DX80 Performance 900MHz (Australia)
Important: To adjust the transmit power on the Gateway radio, Banner recommends using the LCD menu
(System Conf > ISM Radio > RF CNTRL).

Figure 18. DIP switch bank 1 and bank 2 Table 8: DIP switch settings for bank 1 (D1)
DIP Switch
1
Antenna OFF 1 Watt (30 dBm, 900 MHz models only) (default configuration)
ON 250 mW (24 dBm, 900 MHz models only), DX80 compatibility

4 mode
LED
3 2 1
3 2 1
ON
ON
DIP Switch DIP Switch Button

Bank 1 Bank 2
3.4 Modbus Registers for the Performance Gateway Radio Module

The DX80 Performance Gateway is a star-based architecture device that contains all the Modbus registers for the wireless
network within the Gateway. To access any input or output values within the entire wireless network, read the appropriate
Modbus register from Gateway.
There are 16 Modbus registers allocated for each device in the wireless network. The first 16 registers (1–16) are allocated
for the Gateway, the next 16 (17–32) are allocated for Node 1, the next 16 (33–48) are allocated for Node 2 and so forth.
There are no inputs or outputs on the DXM embedded Gateway but the Modbus registers are still allocated for them.
Although only seven Nodes are listed in the table, the Modbus register numbering continues for as many Nodes as are in the
network. For example, the register number for Node 10, I/O point 15 , is 175. Calculate the Modbus register number for each
device using the equation:
Register Number = I/O# + (Node# × 16)
Table 9: Modbus holding registers
I/O Point Gateway Node 1 Node 2 Node 3 Node 4 Node 5 Node 6 Node 7
1 1 17 33 49 65 81 97 113
2 2 18 34 50 66 82 98 114
3 3 19 35 51 67 83 99 115
4 4 20 36 52 68 84 100 116
5 5 21 37 53 69 85 101 117
6 6 22 38 54 70 86 102 118
7 7 23 39 55 71 87 103 119
8 8 24 40 56 72 88 104 120
9 9 25 41 57 73 89 105 121
10 10 26 42 58 74 90 106 122
11 11 27 43 59 75 91 107 123
12 12 28 44 60 76 92 108 124
13 13 29 45 61 77 93 109 125
14 14 30 46 62 78 94 110 126
15 15 31 47 63 79 95 111 127
16 16 32 48 64 80 96 112 128

Table 10: Access all wireless network registers by reading Modbus slave ID 1
DX80 Device Slave ID Modbus Registers
DXM Gateway radio 1 Modbus registers 1–8 are inputs, 9–16 are outputs
Node 1 - Modbus registers 17–24 are inputs, 25–32 are outputs
3.4.1 Alternative Modbus Register Organization

The Sure Cross DX80 Alternative Modbus Register Organization registers are used for reordering data registers to allow host
systems to efficiently access all inputs or outputs using a single Modbus command. The register groups include the input/
output registers, bit-packed registers, and analog registers. This feature is only available with the Performance models using
version 3 or newer of the LCD firmware code.
Table 11: Alternative Modbus register organization
Name Modbus Register Address (Decimal)
Inputs and Outputs, in order by device 2201 through 4784
Discrete Bit Packed (Status, Discrete Inputs, Discrete Outputs) 6601 through 6753
Analog Inputs (1–8) and Analog Outputs (1–8) 6801 through 9098
Input Registers and Outputs Registers

Modbus registers 2201 through 2584 are used to organize all inputs together.
In this format, users can sequentially read all input registers using one Modbus message. Modbus registers 4401 through
4784 organize all outputs together to allow users to sequentially write to all outputs registers using one Modbus message.
Table 12: Input and output registers
Inputs (2201–2584) Outputs (4401–4784)
Modbus Register Address 16-bit Register Value Modbus Register Address 16-bit Register Value
(Decimal) (Decimal)
2201–2208 Gateway Inputs 1 through 8 4401–4408 Gateway Outputs 1 through 8
2209–2216 Node 1 Inputs 1 through 8 4409–4416 Node 1 Outputs 1 through 8
... ... ... ...
Refer to your device's datasheet for a list of the active inputs and outputs. Not all inputs or outputs listed in this table may be
active for your system.
Discrete Bit-Packed Registers

Discrete bit-packed registers include the discrete status registers, discrete inputs, and discrete outputs.
Bit packing involves using a single register, or range of contiguous registers, to represent I/O values.
When networks use similar Nodes to gather data using the same I/O registers for each Node, discrete data from multiple
Nodes can be bit packed into a single register on the Gateway. The bit-packed data is arranged by I/O point starting at
Modbus register 6601. For example, Discrete IN 1 for all the Nodes in the network is stored in three contiguous 16-bit
registers.
The most efficient way to read (or write) discrete data from a Sure Cross® DX80 Gateway is by using these bit-packed
registers because users can read or write registers for all devices using one Modbus message. The following registers
contain discrete bit-packed I/O values for the Gateway and all Nodes. Values are stored first for the Gateway, then for each
Node in order of Node address.

Figure 19. Discrete bit-packed register addresses and bit positions
Bit-Packed Device Status R egisters

Bit Position
Register Address 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
6601 Node 15 Node 14 Node 13 Node 12 Node 11 Node 10 Node 9 Node 8 Node 7 Node 6 Node 5 Node 4 Node 3 Node 2 Node 1 Gateway
6602 Node 31 Node 30 Node 29 Node 28 Node 27 Node 26 Node 25 Node 24 Node 23 Node 22 Node 21 Node 20 Node 19 Node 18 Node 17 Node 16
Bit-Packed Discrete Input 1

Bit Position
Bit-Packed Discrete Output 1

Bit Position
Table 13: Discrete bit-packed registers for inputs and outputs
Inputs Outputs
Modbus Register Address Description (Inputs) Modbus Register Description (Outputs)

(Decimal) Address (Decimal)
6601–6603 Status for all devices
6611–6613 Input 1 from all devices 6691–6693 Output 1 from all devices
6681–6683 Input 8 from all devices
Status registers (6601–6603) contain a bit-packed representation defining the devices that are operational in the wireless
system. Each bit indicates Node in Sync (1) or Node Not in Sync (0).
Input registers from all devices use Modbus registers 6611 through 6683 to organize the least significant bit into a
sequential array of registers. The first register contains the least significant bit from the input values for the Gateway through
Node 15. The second register contains the input values for Node 16 through Node 31, and the third register contains the
input values for Nodes 32 through 47.
For discrete inputs, only the least significant bit is used. For analog inputs, the least significant bit indicates if the analog
value is above or below the selected threshold value (when using the threshold parameter configured in the User
Configuration Software). For example, a least significant bit of one (1) indicates the analog value is above the selected
threshold value. A least significant bit of zero (0) indicates the analog value is below the threshold value.
Output registers from all devices use Modbus registers 6691 through 6753 to organize the least significant bit into a
sequential array of registers. Output 8 (I/O point 16) cannot be written using the discrete format.
Analog 16-Bit Registers (Registers 6801 through 9098)

The most efficient way to read (or write) analog data from a Gateway is by using these 16-bit analog registers. Most networks
consist of similar Nodes reporting data using the same I/O registers for each Node. For this reason, the analog data is
arranged by I/O point using Modbus registers 6801 through 9098.
For example, Input 1 for Gateway and all Nodes is stored in the first 48 contiguous blocks of 16-bit analog registers,
beginning with register 6801.

In this format, users can read a 16-bit holding register for all devices or write to a register for all devices using one Modbus
message. Using these registers is the most efficient way to read all status registers, read all analog inputs, or write all analog
outputs.
The following registers contain analog I/O values for the Gateway and all Nodes. Values are stored first for the Gateway,
then for each Node in order of Node address.
Table 14: Analog input and output registers
Inputs Outputs
Modbus Register Address Description (Inputs) Modbus Register Address Description (Outputs)
(Decimal) (Decimal)
6801 Input 1 for Gateway 8001 Output 1 for Gateway
6802 Input 1 for Node 1 8002 Output 1 for Node 1
... ... ... ...
... ... ... ...
... ... ... ...
7851 Input 8 (Status Register) for Gateway 9051 Output 8 for Gateway
7852 Input 8 (Status Register) for Node 1 9052 Output 8 for Node 1
7853 Input 8 (Status Register) for Node 2 9053 Output 8 for Node 2
... ... ... ...
For example, 6801 contains the input 1 value for the Gateway, 6802 contains the input 1 value for Node 1, and 6848 contains
the input 1 value for Node 47.

4 Processor Connections
Figure 20. DXM1200 base board
DIP Switches 1-4
ON
1
Micro USB
Cellular Modem Connector
Micro SD
Card Holder
Cellular Modem Connector
LED 1 (Status LED)

ON
Reserved
DIP Switches
ISM Radio Connector
Button
ISM Radio Connector LED 2
Figure 21. DXM1200 base board, cellular modem board, and ISM radio board
Cell Modem
SIM card*
location Micro USB
Antenna Cable
ISM
Radio
Board

Button Operation
The button is used for special functions, as defined in the configuration or advanced configuration instructions.
LED Operation
LED1 flashes to indicate the processor board is running.
The LED starts flashing about 10 seconds after power is applied and a network connection is present. Without an
ethernet network connection the LED starts to flash after about 40 seconds.

Cellular Modem Connection

Install the cellular modem onto the board with the cellular modem's U.FL connector as shown. Only install/remove a
cellular modem when the power to the device is disconnected.
4.1 DIP Switch Settings for the Base Board

After making changes to the DIP switch settings, cycle power to the device.
Table 15: DIP switches for the base board
DIP Switches
Settings
1 2 3 4
OFF *
Disable Ethernet Port
ON
OFF *
Disable LCD Display
ON
Not used OFF *
OFF *
Bypass XML
ON
Bypass XML
Turn on to have the XML file ignored at boot time. This is useful for ignoring a corrupt or questionable XML
configuration file. After the device is running, a new XML file can be loaded using the DXM configuration tool.
Turn on to stop the processor from executing defined configuration. This is useful if the loaded configuration is using
all the processing time and not allowing DXM Configuration Tool operations.
The factory default position is OFF.
Disable Ethernet Port
Set to on to power down the Ethernet interface. Disabling the unused Ethernet port reduces power consumption.
Disable LCD Display
Set to on to disable the LCD. This DIP switch should be on when the LCD display board is not connected.
4.2 Ethernet
Before applying power to the DXM1200, verify the Ethernet cable is connected.
The number of times the processor attempts to connect to the Ethernet network is configured in the DXM Configuration
Software (Settings > Network Ethernet Connection Acquisition). The default setting is two retries one minute after the
device boots up another retry two minutes later.
The Ethernet connection supports the DXM Configuration Software, Modbus/TCP, and EtherNet/IP. ScriptBasic also has
access to Ethernet for custom programming. Use the software or LCD menu system to configure the characteristics of the
Ethernet connection, including the IP address. Any parameters not changeable from the menu system are configurable from
the configuration software.
Ethernet parameter changes entered through the LCD menu override the XML configuration parameters. To return to using
the network settings in the XML configuration file, remove the Ethernet parameters defined by the LCD menu using the
System Config > Ethernet > Reset menu.
4.3 USB
A micro USB port is available inside the DXM1200.
The micro USB port can be used to configure the DXM, but a micro USB cable is not provided with the device.

4.4 Internal Local Registers (Slave ID 199) for the DXM700, DXM1000,
and DXM1200
The main storage elements for the DXM1200 are its local registers, which can store 4-byte values that result from register
mapping, action rules, or ScriptBasic commands.
Local registers updated from Modbus transactions are restricted to a16-bit data value to follow standard Modbus holding
register definition.
The local registers defined in action rules must all be within the same register group. For example, an action rule cannot have
inputs from an integer group with the result register defined as a floating point register. To move between integers and floats,
use the Register Copy Rule.
• Local registers 1–850 and 5001–7000 are 32-bit integer registers
• Local registers 851–900 and 7001–8000 are non-volatile 32-bit integer registers
• Local registers 901-1000 are reserved for internal use
• Local registers 1001–5000 are floating point format numbers, each address stores half of a floating point number; for
example, registers 1001 and 1002 store the first full 32-bit floating point number
• Local registers 10000 and higher are read only virtual registers; virtual registers collect various system-level data
Local registers 1–850 and 5001–7000 (Internal Processor Memory, 32-bit, Unsigned)—The local registers are the main
global pool of registers. Local registers are used as basic storage registers and as the common data exchange mechanism.
External Modbus device registers can be read into the local registers or written from the local registers. The DXM1200, as a
Modbus master device or a Modbus slave device, exchanges data using the local registers. Modbus over Ethernet (Modbus/
TCP) uses the local registers as the accessible register data.
Local registers 851–900 and 7001–8000 (Data Flash, Non-volatile, 32-bit, Unsigned)—The top 50 local registers are
special non-volatile registers. The registers can store constants or calibration type data that must be maintained when power
is turned off. This register data is stored in a data flash component that has a limited write capability of 100,000 cycles, so
these registers should not be used as common memory registers that change frequently.
Local registers 1001–5000— These local registers are paired together to store a 32-bit IEEE floating point format number in
big endian format. Registers 1001 [31:16], 1002 [15:0] store the first floating point value; registers 1003, 1004 store the
second floating point number. There are a total of 2000 floating point values; they are addressed as two 16-bit pieces to
accommodate the Modbus protocol. Use these registers when reading/writing external devices that require Modbus registers
in floating point format. Since Modbus transactions are 16-bits, the protocol requires two registers to form a 32-bit floating
point number.
Virtual registers—The DXM1200 has a small pool of virtual registers that show internal variables of the main processor.
Some register values will be dependent upon the configuration settings of the DXM1200. Do not use Read Rules to move
virtual local registers data into local registers. Use the Action Rule > Register Copy function to move virtual local registers
into local registers space (1–850).
Table 17: Modbus registers for virtual registers
Registers Definition
10001 GPS latitude direction (N, S, E, W)
10002 GPS latitude

GPS Coordinate Data if the DXM is configured to read an external GPS unit.
10003 GPS longitude direction (N, S, E, W)
10004 GPS longitude

10011–10012 Resync timer Engineering use
10013–10014 Resync timer rollover Engineering use
10015–10016 Reboot cause (Restart Codes above) Reboot Type
10017–10018 Watchdog reset count Counter to track how many resets have been caused by the Watchdog
10021 IO Board Battery Voltage (mV) mV
10022 IO Board - Incoming Supply Voltage (mV) mV
0—No successful readings

10023 IO Board Voltage Cut-off Feature 1—Normal range
2—Cut-off engaged
10024 IO Board - Battery Charging Current (mA) mA
10025–10026 Http Push SSL Acquires

Statistical counts of connections, disconnections and forced disconnects when
10027–10028 Http Push SSL Releases
the DXM1200 creates a connection using SSL/TLS (Encrypted connections)
10029–10030 Http Push SSL Forced Releases
10031–10032 Http Push Attempts

Statistical counts of connections, disconnections and forced disconnects when
10033–10034 Http Push Successes
the DXM controller creates a connection using HTTP non-encrypted
10035–10036 Http Push Failures
Last DXM1200 push status

0 = Initial state, no push attempt as finished yet
10037–10038 Http Push Last Status
1 = Attempt complete
2 = Attempt aborted
Cellular signal strength. Value range: 0–31

0 = –113 dBm or less
10039–10040 Cellular Strength, BER 1 = –111 dBm
2–30 = –109 dBm through –53 dBm in 2 dBm steps
31 = –51 dBm or greater
99 = not known or not detectable; BER not used
10055–10056 Alarms, smtp, attempts Email attempts
10057–10058 Alarms, smtp, fails Email failures
10100 Number of read maps in default
10101 Number of read map successes
10102 Number of read map timeouts Read Map statistics
10103 Number of read map errors
10104 Read map success streak
10105 Number of write map successes
10106 Number of write map timeouts

Write Map statistics
10107 Number of write map errors
10108 Write map success streak
10109 Number of passthrough successes
10110 Number of passthrough timeouts

API message passing statistics
10111 Number of passthrough errors
10112 Passthrough success streak
10113 Number of 43 buffer successes

DX80 Gateway automatic messaging buffer statistics
10114 Number of 43 buffer timeouts

10115 Number of 43 buffer errors
10116 43 buffer success streak
11000 Read map success count
12000 Write map success count
13000 Read map timeout count
14000 Write map timeout count
15000 Read map error count Read/Write maps statistics
16000 Write map error count
17000 Read map success streak
18000 Write map success streak
19000 Read map is in default
TCP Client Stats—The "x" represents the socket 0 through 4. The flex socket is not used. This range repeats for the next
socket.
Table 18: TCP client statistics
Register Definition
2x001 Socket x connection attempts (20001 is the first socket, 21001 is the second socket...)
2x003 Socket x connections
2x005 Socket x disconnections
2x007 Socket x transmits
2x009 Socket x receives
2x011 Socket x resolver attempts (reserved)
2x013 Socket x resolvers (reserved)
2x015–2x020 Reserved
2x021 Socket x Rule 0 transmits
2x023 Socket x Rule 0 receives
2x025 Socket x Rule 0 timeouts
2x027 Socket x Rule 0 broadcasts
2x029 Reserved
2x031 Socket x Rule 1 transmits
2x033 Socket x Rule 1 receives
2x035 Socket x Rule 1 timeouts
2x037 Socket x Rule 1 broadcasts
2x039 Reserved
Reset Codes—The reset codes are in virtual register 11015 and define the condition of the last restart operation.
Table 19: Reset codes
Reset Code Definition
0 Undefined
1 Unknown
2 General

Reset Code Definition
3 Brownout
4 Watchdog
5 User
6 Software
7 Return from backup mode
4.5 Modbus RTU Master

The DXM1200 can be a Modbus RTU master device to other slave devices.
The DXM1200 uses the primary RS-485 port as a Modbus RTU master to control external slave devices. All wired devices
connected to the master RS-485 port must be slave devices. As a Modbus RTU master device, the DXM1200 controls
external slaves connected to the primary RS-485 port, the local ISM radio, local I/O base board, and the local display board.
Use the DXM Configuration Software to define operational settings for both the Modbus RTU master port and the Modbus
RTU slave port.
The basic communications parameters for the RS-485 ports are set in the DXM Configuration Software and are saved in the
XML configuration file. All basic settings are available under Settings > System screen.
Master port parameters include:
• Baud rate and parity
• Set the Communications Timeout parameter to cover the expected time for messages to be sent throughout the
wireless network. For the DXM1200, the Communications Timeout parameter is the maximum amount of time the
DXM1200 should wait after a request is sent until the response message is received from the Modbus slave device.
• Delay Between Messages sets the minimum wait time from the end of a Modbus transaction to the beginning of the
next Modbus transaction.
Figure 22. Settings > General screen

5 Cellular Modem Boards

5.1 Cellular Modem Board for GSM and LTE
The GSM or LTE cellular modem is an optional accessory that is installed on the two 12-pin sockets.
Plug the cellular modem into the right socket (when viewing the internal PCB with the connectors at the bottom). The SIM
card slides into the socket on the back of this board.
Figure 23. Cellular modem board (optional)
U.FL antenna
connector
5.2 Cellular Power Requirements

If the incoming voltage drops below 11.2 V DC, the cellular modem does not turn on and will not turn on until the voltage is
above 11.8 V DC. A text file (CmVMon.txt) on the internal micro SD card saves the periodic sampling of the incoming
voltage. If cellular operation stops because of voltage, it is logged in this file.
5.3 Using the DXM Cellular Modem

The DXM cellular modem provides a remote network connectivity solution for the DXM1200.
To use the cellular modem:
1. Verify the cellular modem is installed and the correct antenna is connected to the cellular antenna port.
2. Activate the cellular service.
3. Configure the DXM1200 to use the cellular network as the network interface.
5.3.1 Activating a Cellular Modem

Follow these basic steps to activate the cellular capabilities of your DXM Controller.
1. Purchase a cellular modem kit from Banner Engineering Corp.
2. Activate a cellular plan to the SIM card, then insert the SIM card into the cellular modem.
3. Install the cellular modem, connect the antenna cable, and connect the cellular antenna.
4. Configure the DXM to use the cellular modem.
Table 20: Cellular modem kit models
Cellular Kit Model Kit Description
Verizon LTE cellular modem using Telit LE910 modem kit (Verizon part number SENSX002). Includes a cellular modem, SIM
card, antenna, and antenna cable. The SIM card is specific to the LTE technology and cannot be used in other cellular
SXI-LTE-001 modems. Requires a LTE Verizon cellular wireless plan attached to the ICCID (SIM card) number and IMEI (International
Mobile Equipment Identity) number.
Cellular plans can be purchased through secure.bannercelldata.com.

Verizon CAT M1 cellular modem using Telit ME910 modem kit (Verizon part number SXIM1V). Includes a cellular modem, SIM
card, and internal adhesive antenna. The SIM card is specific to the CATM1 technology and cannot be used in other cellular
SXI-CATM1VZW-001 modems. Requires a LTE Verizon cellular wireless plan attached to the ICCID (SIM card) number and IMEI (International
ATT CAT M1 cellular modem using Telit ME910 model kit. (ATT part number SXIM1A). Includes a cellular modem, SIM card.
and internal adhesive antenna. The SIM card is specific to the CATM1 technology and cannot be used in other cellular
SXI-CATM1ATT-001 modems. Requires a LTE AT&T cellular wireless plan attached to the ICCID (SIM card) number and IMEI (International Mobile
Equipment Identity) number.
For additional information, refer to the Banner Cloud Data Services support center (support.bannercds.com). The support
center includes video tutorials, product documentation, technical notes, and links to download configuration software.
Important: Only the DXM100 and DXM150 models offer SMS/text messaging capabilities directly from the
device. SMS/text messaging can be delivered using the BannerCDS web service from any DXM model.
Install the Cellular Modem (DXM100, 150, 700, and 1000 Models)
Follow these steps to install the cellular modem and antenna cable.
Important:
Before you activate your cellular plan, verify you have one of the following cellular modem kits.
Figure 24. Installing the cellular modem
2 3

1. Insert the SIM card into the socket on the underside of the cellular modem. SIM cards come in a credit card sized
carrier. Snap it out and insert the SIM card into the holder on the cellular modem.
Make note of the IMEI number of the cellular modem and the ICCID number of the SIM card. The numbers can be
found on the cellular modem and the SIM card or SIM card carrier. You will need the SIM number to associate a
wireless plan to this SIM card.
2. Orient the cellular modem according to the pin layout and verify the pins are properly aligned. Firmly press the
modem into the 24-pin socket.
• For the DXM100, DXM150, and DXM1000 models—Install the cellular modem board onto the processor board as
shown. Use the diagram below to verify the orientation is correct.
• For the DXM700 models—Install the cellular modem board onto the base board as shown. Use the diagram
below to verify the orientation is correct.
3. Attach the antenna cable between the cellular modem board to the base board as shown.
4. Install the external cellular antenna on the DXM's SMA connector located next to the antenna cable.
Figure 25. DXM100, 150, and 1000 Figure 26. DXM700
SIM card*
location
SIM card*
location
Antenna Cable
Modem Modem
Antenna Cable
*SIM card is located on the underside of installed modem *SIM card is located on the underside of installed modem
Install the Cellular Modem (DXM1200 Models)

Follow these steps to install the cellular modem and antenna cable.
Important:
Before you activate your cellular plan, verify you have one of the following cellular modem kits.

Figure 27. Installing the cellular modem
2 3
1. Insert the SIM card into the socket on the underside of the cellular modem. SIM cards come in a credit card sized
carrier. Snap it out and insert the SIM card into the holder on the cellular modem.
Make note of the IMEI number of the cellular modem and the ICCID number of the SIM card. The numbers can be
found on the cellular modem and the SIM card or SIM card carrier. You will need the SIM number to associate a
wireless plan to this SIM card.
2. Apply the internal antenna as shown paying attention to the antenna cable position.
a) Pull back the adhesive protective paper from the middle of the antenna, only exposing the middle portion.
Antenna application is easier if just a small middle portion of the adhesive is uncovered.
b) Center the antenna on the side wall. Use the exposed adhesive in the middle of the antenna to hold the antenna
in place while aligning the antenna to the full length of the housing.
c) Slowly peel off the paper backing exposing the adhesive and stick to the plastic housing. The antenna should run
below the rim of the housing.
d) Press firmly.
3. Orient the cellular modem according to the diagram below and verify the pins are properly aligned. Firmly press the
modem into the 24-pin socket on the board.
The cellular modem is inserted into the main board with the antenna cable from the applied internal antenna attached
to the cellular modem PCB.
4. Attach the antenna cable between the cellular modem board to the base board. The antenna cable uses the top
antenna connection.
Figure 28. Internal view of a DXM1200
Cell Modem
SIM card*
location Micro USB
Antenna Cable
ISM
Radio
Board

Activate a 4G LTE or CAT M1 Cellular Plan

Activate a cellular plan for your DXM1200 using the Banner Cloud Data Services website.
1. Go to secure.bannercelldata.com to purchase cellular data plans.
2. If you have previously created an account, click Login and enter your username and password to continue.
3. If you are creating a login for the first time:
a) Select the region in which the device will operate.
b) Select the cellular subscription plan. Please use the calculator and regional coverage information to determine the
plan needed for your device (https://support.bannercds.com/home/pricing/how-to-choose-a-cellular-service-plan).
c) Create a username and password (use an email address for the username).
d) Enter your payment information, mailing address, agree to the terms and conditions.
4. Go to the My Services and Equipment section.
5. Enter the SIM Number (ICCID) and the Module Number (IMEI).
The ICCID is the 20-digit number of the SIM, the bottom barcode number on the SIM card carrier. If the carrier card is
not available, the ICCID is also printed on the SIM card, but must be removed from its socket to be read. The IMEI is
the 15-digit number on top of the 4G LTE device.
6. Click Activate.
Note: Although new activations are typically functional in 20 minutes or less, it may take up to 24
hours for the cellular plan to become active on the wireless network.
Configure the DXM Controller for a Cellular Modem

Use the DXM Configuration Software to create a configuration using a cellular connection.
Important: Only the DXM100 and DXM150 models offer SMS/text messaging capabilities directly from the
device. SMS/text messaging can be delivered using the BannerCDS web service from any DXM model.
1. Go to the Settings > Cloud Services screen.

2. Set the Push Interface to Cell
All push data, SMS messages, or email alerts will be sent using the cellular modem.
3. Go to the Settings > Cellular screen. Under the Cell Configuration section, select the Cell module from the drop-
down list.
• For North America—For Verizon LTE/CATM modems, select VZW LTE/CATM and set the APN to vzwinternet.
For ATT LTE/CATM modems, select ATT LTE/CATM and set the APN to iot0119.com.attz. Requires a SIM
module to be purchased from a wireless carrier based on the IMEI number of the cellular modem. The wireless
carrier will provide the APN parameters. Not all parameters may be required.
4. To send data to the webserver, complete the parameters on the Settings > Cloud Services screen. Set the Cloud
push interval and the Web Server settings. (For more information, refer to the DXM Configuration Software
Instruction Manual (p/n 201127).
When the DXM1200 is configured to use the cellular modem, the information on the cellular modem is found on the LCD
menu under System Info > Cell. The menu does not display values until a transaction with the wireless cell tower is
complete.
If there are no webserver parameters defined, the user must force a push to retrieve the data from the cellular network. On
the LCD menu, select Push > Trigger Data Push.
Obtaining LTE service outside of the Banner Cellular Data Plans—Customers have the option of securing a data plan for
the Verizon network themselves without using the Banner cellular data portal (secure.bannercelldata.com). Suitable plans
would include those available from Verizon directly or from a Mobile Virtual Network Operator (MVNO) licensed to resell
Verizon network data plans. (The SXI-LTE-001 will not function on AT&T, T-Mobile, or Sprint networks.) When purchasing a
data plan, it is important to refer to the modem by its official Verizon network name (for example, SENSX002) and give the
IMEI number (found on the cellular modem) to the plan provider. To use the SIM card that comes with the cellular modem kit,
give the SIM card number to the provider. The required SIM card form factor is 3FF - Micro.

6 LCD and Menu System

The LCD has four user-defined LED indicators, four control buttons, and an LCD. The four buttons control the menu system
on the LCD menu.
Figure 29. Top-level menu
Banner Eng 08:25:45
↑ → Registers
→ Push S → 08:25:15
ENTER
→ ISM Radio
→ I/O Board
→ System Config
↓ → System Info BACK
The top-level menu always displays the time in a 24-hour format.

• The up and down arrows scroll through display items.
• The ENTER button selects the highlighted items on the display
• The BACK button returns to a previous menu option.
The left display column shows an arrow at the beginning of the line if the menu has submenus. The right column shows a
vertical line with an arrow at the bottom if the user can scroll down to see more menu items.
The DXM can be configured to require a passcode be entered before the LCD and Menu system will operate. The passcode
configuration is defined in the DXM Configuration Software.
6.1 Registers
The Registers submenu displays the processor's local registers that can be configured using the DXM Configuration
Software.
To configure these local registers, launch the DXM Configuration Software. Go to Local Registers and expand the view for a
local register by clicking on the down arrow next to the register number. In the LCD Permissions field, select None, Read,
Write, or Read/Write.
Figure 30. Registers menu
Registers List of Local Register

Values and the Register Name
↑ ↓ to change the value
ENTER to accept
BACK to return to the previous menu
Read allows the register to be displayed, and Write or Read/Write allows the register value to be changed using the LCD.
The Units and Scaling parameters are optional and affect the LCD.
6.2 Push
The Push menu displays information about the last data sent to the Webserver.
Figure 31. Push menu
Push Trigger Data Push Trigger Data Push

Status
Time (hh:mm:ss)
ENTER to accept

The user can force an immediate push to the webserver using Trigger Push. If a current push is in process it may take
several minutes to complete over cellular.
• The Trigger Push submenu forces an immediate push to the web server.
• The status and time fields indicate success or failure of the last attempted push and time of the last attempted push.
6.3 ISM Radio

The ISM Radio menu allows the user to view the Modbus ID of the internal ISM radio, enter binding mode, or run a site
survey. This top-level ISM Radio menu is different from the System Config > ISM Radio submenu.
The first option under the ISM Radio menu only displays the type of radio in the DXM1200 (MultiHop or DX80 Star) and the
Modbus ID of the radio. To change the ISM Radio Modbus ID refer to the System menu.
Select Binding to enter binding mode or select Site Survey to run a site survey.
Figure 32. ISM Radio menu
ISM Radio MultiHop/DX80 ID

Binding Bind to > 1
ENTER to accept
Site Survey Node/Modbus ID > 1 BACK to return to the previous menu
Please Wait...
Site Survey results OR Failed to start Site Survey
Binding— All ISM radio devices must be bound to the internal Gateway/master device before the DXM1200 can access the
wireless devices. The first submenu under binding allows the user to set the wireless address of the device to bind with. This
is required to bind with wireless devices that do not have rotary dials (for example: M-GAGEs, ultrasonic sensors, and Q45
devices). See Binding and Conducting a Site Survey with the ISM Radio on page 11. For more information on binding a
particular device, refer to the individual datasheet.
Site Survey—After creating a wireless network using the binding process, run a site survey on each device to see the link
quality. See Conduct a Site Survey from the DXM on page 13.
6.4 System Config

Use the System Config menu to set DXM1200 system parameters.
Figure 33. System Config menu
System Config ISM Radio DX80 ID: x New ISM Modbus ID: x
Auto Detect Radio Radio Detected Type: DX80
ID: 1
Advanced Options Ref Type: DX80
Ref Modbus ID: x
Max Node Count: xx New ISM Max Nodes: xx
Binding #: xxxxxx New ISM Binding Code: xxxxxx
RF Ctrl: Dip 1.00W
Ethernet DHCP Update DHCP Mode After making changes to the

IP: Update IP Address Ethernet settings, restart the DXM.
SN: Update SN
GW: Update GW Address
Reset Resets Ethernet parameters
to xml defaults.
Provision Cell
DXM Modbus ID: xxx ↑ ↓ to change the value
LCD Contrast: xx ENTER to accept
Restart
BACK
to return to the previous menu

The System Config submenus are:

• ISM Radio
• Ethernet
• Provision Cell
• DXM Modbus ID
• LCD Contrast
• Restart
6.4.1 ISM Radio

DX80/MultiHop ID—The ISM radio is set at the factory to be Modbus device address 1 (Modbus ID 1). For some
applications, you may need to change the Modbus ID. Adjust the Modbus device address using the LCD menu system. Any
other method may cause issues with the DXM1200 not knowing which Modbus device address is assigned to the radio,
which causes issues with running Binding or Site Survey from the LCD menu.
Set the radio Modbus ID to a valid number (1 through 247) that is not being used by the DXM system. Processor Local
Registers allocate ID 199, the I/O board is set to ID 200, and the display board is set to ID 201. With a DX80 Gateway (star
network), it's easy to choose a new ID. With a MultiHop network, remember that the master MultiHop radio allocates a range
of Modbus IDs for wireless devices, typically 11 through 110.
When setting the new ISM Modbus ID, the system changes the Modbus ID on the internal radio and changes the reference
to it on the DXM1200. The reference Modbus ID is what the DXM1200 uses to access the internal radio when running
Binding or Site Survey.
Auto Detect Radio—If the internal Modbus ID of the radio was changed or the internal radio was changed, but not recorded,
use Auto Detect Radio to determine the radio ID and radio type. The auto-detect routine broadcasts discovery messages and
waits for a response. If other devices are connected to the external RS-485 ports, they may need to be disconnected for this
process to work properly.
Advanced Options—The Advanced Options menu is typically not used unless the Modbus ID is changed without the
DXM1200 being involved, such as when you write directly to the radio Modbus registers.
• Reference Type selects the radio type between DX80 star architecture radios and a MultiHop radio. The DXM1200
uses this reference to determine how to communicate to the internal radio. If set incorrectly, the DXM1200 may not
be able to run Site Survey from the LCD menu. Unless you are changing or adding the internal radio device, there
should no reason to change the radio type.
• Reference Modbus ID defines the Modbus ID the DXM1200 uses when communicating with the internal radio. If this
is set incorrectly, the DXM1200 will not be able to run Binding or Site Survey through the LCD menu.
Max Node Count—Defines the maximum number of devices for the DX80 wireless network.
Binding #—This parameter allows the user to define the Binding code within the ISM radio. Typically, you will not have to
adjust this number unless you are replacing an existing Gateway or master radio.
RF Ctrl—Displays the status of the ISM radio DIP switch 1 (off or on). The menu doesn't allow the user to change the DIP
switch setting through the display.
6.4.2 Ethernet
Use the Ethernet submenu to sets the IP Address, Gateway Address, and Subnet mask of the DXM1200's Ethernet
interface. You may change these settings either from the LCD menu (System Config > Ethernet) or from the XML
configuration file created by the DXM Configuration Software.
The network address settings from the LCD menu have the highest priority and override settings in the XML configuration
file. To use the parameter settings from the XML configuration file or use DHCP, execute the Reset under System Config >
Ethernet or use the LCD display to set the IP Address, Gateway Address, and Subnet Mask to 255.255.255.255. Reboot the
DXM1200 after changing the Ethernet parameters.
The Ethernet cable should be attached before powering up the DXM1200.
6.4.3 LCD Contrast

Use the LCD Contrast option to adjust the LCD contrast. Adjust the starting number lower to decrease the display contrast.
The factory default is 28. Do not set a number less than 15 or the display may not be bright enough to see to change back.
6.4.4 Reset
Use the Restart menu to force the main processor to restart. This does not affect the other boards in the system.

6.5 System Info

Various DXM system settings are shown in this menu. The Push, Ethernet, and Cell parameters are helpful for debugging
network connections. This is a read only menu.
Figure 34. System Info menu
System Info Controller Date:

Firmware:
Build:
Model:
Serial: ENTER to accept
Push Method:
Interval: hh:mm BACK to return to the previous menu
URL:
Page:
Https: on/off
Site ID:
ISM Radio Serial:
Model:
Date:
RF FW Pt:
RF FW Ver:
RF EE Pt:
RF EE Ver:
Ethernet DHCP: Wifi IP:
IP: Mode:
Subnet: AP:
Gate: Stat:
Mac: Script Path:
DNS1:
Baud:
DNS2:
Code:
Cell Signal:
Phn#: LCD Board Serial:
Dev#: Model:
SIM: Date:
CellVer: RF FW Pt:
CellMdl: RF FW Ver:
CellFw: RF EE Pt:
CellMask: RF EE Ver:
Controller
Displays the date, build, model, and serial number.
Push
Shows the current parameters loaded from the XML configuration that applies to pushing data to a webserver,
including method (Ethernet or cellular), interval, URL, page, HTTPS, and site ID.
ISM Radio
Displays the serial number, model, date, firmware part numbers, and version numbers.
Ethernet
Displays the IP address, MAC address, DHCP, Gateway address, and DNS settings.
Cell
Shows the cellular MEID number (Mobil Equipment Identifier), MDN (Mobil Device Number), version, signal, firewall
setting, and firewall mask. Some of these parameters are not visible until the cellular network is accessed.
Wifi
Displays the Wifi IP address and other settings.

Sript
Displays the name of the ScriptBasic file running.
LCD Board
Displays the serial number, model, date, firmware part numbers, and version numbers.
6.6 Display Lock

Display Lock protects the DXM LCD menu system from being used until the proper pass code is entered.
Figure 35. Display Lock menu
Display Lock Enter password

>> x
ENTER to accept
The display lock feature uses the configuration software to set a passcode within the DXM. A valid passcode is 1 to 9 digits
long and uses numbers 0 through 9. For example 1234 or 209384754.
6.7 Modbus Registers for the LCD (Modbus Slave ID 201)

Control the four bi-color LEDs using the display's Modbus registers. Using write maps or ScriptBasic, write the Modbus
registers shown below with 0 (off) or 1 (on).
Table 23: Modbus registers for the LCD board (Modbus slave ID 201)
Modbus Register LED Color State
1102 : bit 0 LED 1 Red
1103 : bit 0 LED 2 Green

1 = On
1104 : bit 0 LED 3 Blue
0 = Off
1105: bit 0 LED 4 Amber
1105: bit 0 Backlight

7 Working with Modbus Devices

The DXM1200 has two physical RS-485 connections using Modbus RTU protocol.
The master Modbus RS-485 port is for the DXM1200 to act as a Modbus master device to control internal and external
Modbus slave devices. The Modbus master RS-485 port uses the white (+) and black (-) wires on the M12 quick disconnect
connector.
Figure 36. DXM1200 system overview
Processor/Outputs (Base Board)

Local Registers
(Modbus ID 199) ISM Radio (Modbus ID 1)
Ethernet Local Regi sters Gateway or MultiHop

Integer
Local Registers User Display (Modbus ID 201)
RS-485 (master) Float
LED / LCD Display
Local Registers
Non-Volatile
Internal
Micro USB
Processor Controlled
Cellular Modem
Modbus Data Traffic

Control
The DXM1200 operates the Modbus master port. Each device on the master port must be assigned a unique slave ID. There
are slave IDs that are reserved for internal devices in the DXM1200.
Table 24: DXM internal Modbus slave IDs (factory default)
Modbus Slave ID Device
1 DX80 Performance Gateway or MultiHop ISM Radio—MultiHop wireless devices connected to the internal MultiHop radio
should be assigned Modbus Slave addresses starting at 11.
199 Local Registers—Internal storage registers of the DXM1200
201 LCD—The user has access to the LED indicators on the DXM1200.
7.1 Assigning Modbus Slave IDs

Set the DXM Slave ID from the LCD menu under System > DXM Slave ID. The DXM1200 can have any unique slave ID.
DXM Master Configuration—When the DXM1200 operates as a Modbus master device, use the DXM Configuration
Software to configure read or write operations of the DXM Modbus network. The DXM1200 communicates with all internal
and external peripheral devices using the external Modbus bus RS-485.
There are four internal Modbus slave devices that are configured from the factory with slave IDs. Assign slave IDs of 2
through 10 to Modbus slave devices that are physically wired to the DXM1200. Assign slave IDs or 11 through 60 to wireless
slaves within the MultiHop network.
Do not assign a slave ID of greater than 10 to Modbus slave devices that are physically wired using the RS-485 port if there
is an internal MultiHop ISM radio in the DXM1200. The MultiHop ISM radio attempts to send any Modbus data intended for
slaves 11–60 across the radio network, which conflicts with wired slave devices if the slave IDs overlap. The MultiHop master
radio can be changed from the factory default of 11–60 Modbus slave IDs if more hardwired slaves are required.

7.2 Modbus Operation

All Modbus transactions are managed by a central Modbus engine. If there are Modbus messages intended for a Modbus
slave that doesn't exist, the Modbus engine waits for a response until the timeout period is expired. This slows down the
Modbus polling loop for read and write operations.
For this reason, verify all Modbus read and write operations are intended for Modbus slave devices that are in the network. If
a Modbus slave is not in the network, either a wired or wireless device, the operation of the LCD menu system can be
compromised. Operations like Binding, Site Survey, or accessing the ISM menu may be slower. This is because all internal
devices (such as the ISM radio, LCD, etc) of the DXM1200 are also Modbus slaves.
7.3 Wireless and Wired Devices

Wireless DX80 Performance Gateway—The DX80 Performance Gateway architecture is a star architecture in which all
Nodes in the system send their data back to the Gateway. The host can access the entire network data from the Gateway,
which is Modbus slave ID 1. Because the DXM1200 will not be sending any Modbus messages across the wireless link, the
timeout parameter can be set low (less than 1 second) and the device is treated like a directly connected device.
MultiHop Master—The MultiHop master radio forms a wireless tree network using repeaters and slave devices. Each device
in a MultiHop network must be assigned a unique Modbus Slave ID and is accessed as a separate device.
For the DXM1200 to talk with a MultiHop device in the wireless network, the master MultiHop device interrogates every
message on the RS-485 bus. If they are within the wireless devices range (slave IDs 11 though 60), the message is sent
across the wireless network. To change this range, the user must adjust the offset and range setting in the MultiHop master
radio (Modbus Slave ID 1). Modbus register 6502 holds the Modbus offset, default 11. Modbus register 6503 holds the
number of Modbus slaves allowed (maximum of 100).
Table 25: Modbus slave IDs for wireless and wired devices
Modbus Slave ID Description
1 Allocated for the internal ISM radio device, either a DX80 Performance Gateway or MultiHop Master
2–10 Slave addresses available for direct connected Modbus slave devices to the master RS485 port (M+ , M-)
11–60 Allocated for wireless MultiHop radio network devices. If there is not an internal MultiHop in the DXM1200, these slave addresses
are available to use for directly connected devices.
61–198 Available to user for direct connected Modbus slave devices or the expansion of the wireless network slave IDs to go past 50
wireless devices.
199 Allocated for internal Local Register
201 Allocated for the LCD display board, the user can read/write LEDs.
7.4 Modbus Communication Timeouts

A Modbus timeout is the amount of time a Modbus slave is given to return an acknowledgment of a message sent by the
Modbus master. If the Modbus master waits for the timeout period and no response is seen, the Modbus master considers it
a lost message and continues on to the next operation.
The timeout parameter is simple to set for Modbus devices directly connected to the DXM1200, if there are no MultiHop
wireless devices. Special considerations need to be made to set the timeout parameter when a MultiHop network uses the
DXM1200 as the master radio.
Configure controllers operating wireless networks to allow for enough time for hardware transmission retries. Set the
Communications Timeout parameter to cover the expected time for messages to be sent throughout the wireless network.
For the DXM1200, the Communications Timeout parameter is the maximum amount of time the DXM1200 should wait after
a request is sent until the response message is received from the Modbus slave device. Use the DXM Configuration
Software to set the timeout parameter on the Settings > System screen (select Show advanced settings).
The default setting for the timeout parameter is 5 seconds.
7.4.1 MultiHop Networks vs DX80 Star Networks

The DX80 star Gateway collects all the data from the Nodes, which allows the host system to directly read the data from the
Gateway without sending messages across the wireless network. This allows for DX80 Gateway to be treated like any other
wired Modbus device.

In a MultiHop network, the data resides at each device, forcing the controller to send messages across the wireless network
to access the data. For this reason, carefully consider the value of the wireless timeout parameter.
7.4.2 Calculating the Communications Timeout for Battery-Powered

MultiHop Radios
Battery-powered MultiHop radios are configured to run efficiently to maximize battery life. By optimizing battery life, the
allowed communications window for receive messages is slow (once per 1.3 seconds) and sending message rates are
standard (once per 0.04 seconds).
A MultiHop device is set from the factory with the retry parameter of 8. This means that under worst-case conditions, a
message is sent from the DXM1200 to an end device a total of nine times (one initial message and eight retry messages).
The end device sends the acknowledgment message back to the DXM1200 a maximum of nine times (one initial message
and eight retries). A single Modbus transaction may send up to two messages + 16 retry messages before the transaction is
complete. In addition, the radios randomly wait up to one time period before retransmitting a retry message. So to allow for
the random wait time, add one extra time period for each in-between time of retries.
To calculate the communication timeout parameter for a Master radio to a slave radio (no repeaters):
Master to Slave Send time = (9 × 1.3 sec) + (8 retry wait × 1.3 sec) = 22 seconds
Slave to Master Send time = (9 × 0.04 sec) + (8 retry wait × 0.04 sec) = 1 second
Total Send/Receive time = 23 seconds
Minimum Timeout period = 23 seconds
If the link quality of the network is poor, the maximum transfer times may happen. Set the timeout parameter to
accommodate the maximum number of retries that may happen in your application.
When MultiHop repeaters are added into the wireless network, each additional level of hierarchical network increases the
required timeout period. Since MultiHop repeaters are running at the highest communications rate, the overall affect is not as
great.
Master to Repeater Send time = (9 × 0.04 sec) + (8 retry wait × 0.04 sec) = 1 second
Repeater to Master Send time = (9 × 0.04 sec) + (8 retry wait × 0.04 sec) = 1 second
Additional Timeout period for a repeater = 2 seconds
Using the timeout calculation above of 23 seconds, if a repeater is added to the network the timeout should be set to 25
seconds. For each additional MultiHop repeater device creating another level of network hierarchy, add an additional two
seconds to the timeout period.
7.4.3 Calculating the Communication Timeout for 10–30 VDC

MultiHop Radios
Line-powered (10–30 V dc) MultiHop devices operate at the maximum communication rate, resulting in a much lower timeout
parameter setting. For each repeater added to the network, increase the timeout parameter 2 seconds.
For a Master radio to a 10–30 V dc powered slave radio (no repeaters):
Master to Slave Send time = (9 × 0.04 sec) + (8 retry wait × 0.04 sec) = 1 second
Slave to Master Send time = (9 ×* 0.04 sec) + (8 retry wait × 0.04 sec) = 1 second
Total Send/Receive time = 2 seconds
Minimum Timeout period = 2 seconds
7.4.4 Adjusting the Receive Slots and Retry Count Parameters

The number of receive slots governs how often a MultiHop device can communicate on the wireless network.
Battery-powered devices typically have DIP switches that allow the user to set the number of receive slots, which directly
affects the battery life of the radio. Adjusting the receive slots changes how often a message can be received. By default, the
receive slots are set to 4 (every 1.3 seconds). When the receive slots are set to 32, the radio listens for an incoming
message every 0.16 seconds.
Users may also leave the retry mechanism to the application that is accessing the wireless network, in this case the
DXM1200. Adjust the number of retries in the MultiHop devices by writing the number of retries desired to Modbus register
6012. The factory default setting is 8.

7.4.5 Calculating the Communication Timeout for a DX80 Star

Network
In the DX80 network, all Node data is automatically collected at the Gateway to be read. The DXM1200 does not use the
wireless network to access the data, which allows for much faster messaging and much lower timeout values.
For a DXM1200 with an internal DX80 Gateway, set the timeout value 0.5 seconds. If other Modbus slave devices are
connected to the RS-485 lines, the timeout parameter governs all communication transactions and must be set to
accommodate all devices on the bus.
7.5 Modbus TCP Client

The DXM1200 can operate as a Modbus TCP client on Ethernet. Users may define up to five socket connections for Modbus
TCP server devices to read Modbus register data over Ethernet. Use the DXM Configuration Software to define and
configure Modbus TCP client communications with other Modbus TCP servers.

8 Configuration Instructions
8.1 Scheduler
Use the Scheduler screens to create a calendar schedule for local register changes, including defining the days of the week,
start time, stop time, and register values.
Schedules are stored in the XML configuration file, which is loaded to the DXM1200. Reboot the DXM1200 to activate a new
schedule.
If power is cycled to the DXM1200 in the middle of a schedule, the DXM1200 looks at all events scheduled that day and
processes the last event before the current time.
For screens that contain tables with rows, click on any row to select it. Then click Clone or Delete to copy/paste or remove
that row.
8.1.1 Create a Weekly Event

Use the Scheduler > Weekly Events screen to define weekly events.
Figure 37. Scheduler > Weekly Events screen
1. Click Add Weekly Event.

A new schedule rule is created.
2. Click on the arrow to the left of the new rule to expand the parameters into view.
The user-defined parameters are displayed.
3. Name your new rule.
4. Enter the local register.
5. Select the days of the week this rule applies to.
6. Enter the starting value for the local register.
7. Use the drop-down list to select the type of Start at time: a specific time or a relative time.
8. Enter the starting time.
9. Enter the end time and end value for the local register.
Register updates can be changed up to two times per day for each rule. Each rule can be set for any number of days in the
week by clicking the buttons M, T, W, Th, F, S, or Su.
If two register changes are defined for a day, define the start time to be before the end time. Select End Value to enable the
second event in a 24 hour period. To span across two days (crossing the midnight boundary), set the start value in the first
day, without selecting End Value. Use the next day to create the final register state.
Start and end times can be specified relative to sunrise and sunset, or set to a specific time within a 24 hour period. When
using sunrise or sunset times, set the GPS coordinates on the device so it can calculate sunrise and sunset.
8.1.2 Create a One-Time Event

Define one-time events to update registers at any time within a calendar year.
Similar to Weekly events, the times can be specific or relative to sunrise or sunset. Define one-time events using the
Scheduler > One Time Events screen.
Figure 38. Scheduler > One Time Events screen

1. Click on Add One Time Event.

A new one-time event is created.
2. Click on the arrow to expand the parameters into view.
The user-defined parameters are displayed.
3. Name your one-time event by clicking on the name link and entering a name.
4. Enter the local register.
5. Enter the starting time, date, and starting value for the local register.
6. Enter the ending time, date, and ending value for the local register.
8.1.3 Create a Holiday Event

Use the Scheduler > Holidays screen to create date and/or time ranges that interrupt weekly events.
Figure 39. Scheduler > Holidays screen
1. Click on Add Holiday.

A new rule is created.
2. Enter a name your new holiday rule.
3. Select the start date and time for the new holiday.
4. Select the stop date and time for the new holiday.
8.2 Authentication Setup

The DXM1200 has three different areas that can be configured to require a login and password authentication.
• Webserver/ Cloud Services Authentication
• Mail Server Authentication
• DXM Configuration Authentication
The webserver and mail server authentication depends upon the service provider.
8.2.1 Set the Controller to use Authentication

The DXM1200 can be configured to send login and password credentials for every HTTP packet sent to the webserver. This
provides another layer of security for the webserver data.
Configuration requires both the webserver and the DXM1200 to be given the same credentials for the login and password.
The webserver authentication username and password are not stored in the XML configuration file and must be stored in the
DXM1200.
1. From within the DXM Configuration Software, go to the Settings > Cloud Services screen.
2. In the upper right, select Show advanced settings.
3. Define the username and password in the Web Server Authentication section of the screen.
Figure 40. Web Server Authentication screen
The first time you select Require Authentication, a pop-up box appears with additional instructions. Since the data
is not stored in the XML configuration file, it is hidden from view of the DXM Configuration Software.
4. Click on Send Authentication.
The controller must be connected to the PC for this operation to succeed.
The data transmits directly to the DXM1200's non-volatile memory. If successful, a pop-up window appears, asking to
reboot the device.
5. Select Yes to reboot the device.

Set the Web Services to Use Authentication

1. At the Banner Cloud Data Services website, go to Settings > Sites.
2. To edit the site settings, click Edit on the line of the site name.
Figure 41. Settings > Sites screen of the Banner CDS website
At the bottom of the pop-up window is a checkbox to enable authentication/validation.

3. Enter the same username and password as used in the DXM Configuration Software. The username and password
do not need to be a defined user within the Banner Cloud Data Services website.
8.2.2 Controller Configuration Authentication

The DXM1200 can be programmed to allow changes to the configuration files only with proper authentication by setting up a
password on the Settings > Administration screen in the DXM Configuration Software.
With the DXM1200 connected to the PC, click Get Device Status. The DXM1200 status displays next to the button.
Figure 42. Settings > Administration screen
Use the DXM Configuration Software to:

• Set the Admin Password
• Change the Admin Password
• Remove the Admin Password
To change or remove an admin password, the current password must be supplied. The DXM1200 must be connected to the
PC to change the administration password.

8.3 Register Flow and Configuration

The DXM1200 register data flow goes through the Local Registers, which are data storage elements that reside within the
processor. Using the DXM Configuration Software, the controller can be programmed to move register data from the Local
Register pool to remote devices, the internal radio, the I/O base (if applicable), or the display.
Figure 43. Register flow
Processor
Local
Registers
Ethernet/USB/Cellular Remote Devices
Display I/O Base Internal

Radio
8.3.1 Basic Approach to Configuration

When programming an application in the DXM1200, first plan the overall data structure of the Local Registers. The Local
Registers are the main storage elements in the DXM1200. Everything goes into or out of the Local Registers.
1. In the DXM Configuration Software, name the Local Registers to provide the beginning structure of the application.
2. Configure the read/write rules to move the data. The Read/Write rules are simple rules that move data between
devices (Nodes, Modbus slaves, sensors, etc) and the Local Registers.
3. Most applications require the ability to manipulate the Local Register data, not just move data around. Use the Action
rules to make decisions or transform the data after the data is in the Local Registers. Action rules can apply many
different functions to the Local Register data, including conditional statements, math operations, copy operations, or
trending.
4. To perform scheduled events in Local Registers, go to the Scheduler screen in the DXM Configuration Software.
These rules provide the ability to create register events by days of the week. The scheduler can also create events
based on sunrise or sunset.
8.3.2 Troubleshooting a Configuration

View Local Registers using the Local Registers > Local Registers in Use screen of the DXM Configuration Software.
When a configuration is running on the DXM1200, viewing the Local Registers can help you to understand the application's
operation. This utility can also access data from remote devices.
To configure the Local Register data to display on the LCD menu, go to the Local Registers screen, set the LCD
permissions to read or read/write.
8.3.3 Saving and Loading Configuration Files

The DXM Configuration Software saves its configuration information in a XML file. Use the File menu to Save or Load
configuration files.
Save the configuration file before attempting to upload the configuration to the DXM1200. The DXM Configuration Software
uploads the configuration file saved on the PC to the DXM1200; it will not send the configuration loaded in the tool.

8.3.4 Uploading or Downloading Configuration Files

The DXM1200 requires a XML configuration file to become operational. To upload or download configuration files, connect a
computer to the DXM1200 using the USB port or Ethernet port. Then use the Upload Configuration to Device or
Download Configuration from Device under the Device menu.
8.4 EtherNet/IP™ Configuration

The DXM1200 is defined from the factory to send/receive register data from the Gateway and the first 16 Nodes with an
EtherNet/IP™ 1 host.
To expand the number devices going to Ethernet/IP, change the Devices in system parameter in the DX80 Gateway
(default setting is 8) to 32. To change this value:
1. Launch the the DX80 Configuration Software.
2. In the menu bar, go to Device > Connection Settings and select Serial or Ethernet DXM.
3. In the Configuration > Device Configuration screen, click on the arrow next to the Gateway to expand and display
the Gateway's parameters.
4. In the System section, use the Devices in system drop-down list to make your selection.
This allows the user to maximize the use of the EtherNet/IP buffer to 28 devices.
EDS (Electronic Data Sheet) files allow users of the EtherNet/IP protocol to easily add a Banner DXM device to the PLC.
Download the EDS files from the Banner website.
• DXM EDS Configuration File (for PLCs) (p/n b_4205242)
• DXM EIP Config File for DXM Controller with Internal Gateway (Models: DXM1xx-BxR1, DXM1xx-BxR3, and
DXM1xx-BxCxR1) (p/n 194730)
8.4.1 Configuring the Host PLC

On the host PLC, install the DXM1200 using an EDS file or by using the following parameters:
• Assembly1: Originator to DXM = Instance 112, 456 bytes (228 words)
• Assembly2: DXM to Originator = Instance 100, 456 bytes (228 words)
The Originator is the host PLC system, and the DXM is the DXM1200. The host system sees the DXM1200 as a generic
device with the product name of Banner DXM (ProdType: 43 - Generic Device, ProdName: Banner DXM).
Important: Do not set the Requested Packet Interval (RPI) any faster than 150 ms.
8.4.2 Configuring the Controller

Use the DXM Configuration Software to define the Protocol conversion for each local register to be EIP Originator -> DXM
or EIP DXM -> Originator from the Edit Register or Modify Multiple Register screens.
• Define a DXM local register as EIP Originator -> DXM when the host PLC (Originator) will send data to the
DXM1200 local register (DXM).
• Define a DXM local register as EIP DXM -> Originator when that register data will be sent from the DXM1200 (DXM)
to the host PLC (Originator).
Data from an EIP controller in assembly instance 112 is data destined for the DXM1200 local registers. The first two bytes of
the assembly instance are stored in the first local register defined as an EIP Originator -> DXM register. The next two bytes
of the assembly instance are stored in the next local register defined as an EIP Originator -> DXM register. For example, if
DXM local registers 5, 12, 13, and 15 are configured as EIP Originator -> DXM, the first eight bytes (four words) of data from
the assembly instance are stored into these registers in order (5, 12, 13, and 15). The system ignores the rest of the bytes in
the assembly instance.
Data from the DXM1200 local registers is sent to the EIP controller using assembly instance 100. Each local register in the
DXM1200 defined as EIP DXM -> Originator is collected in numerical order and placed into the data buffer destined for
assembly instance 100. DXM local registers are capable of 32-bits, but only the lower 2-bytes for each local register are
transferred. For example, if DXM registers 1, 10, 20, and 21 are defined as EIP DXM -> Originator registers, the assembly
instance 100 will have the first eight bytes of data coming from the DXM local registers 1, 10, 20, and 21. The rest of the data
is in assembly instance 100 is zero.
For example, define register 1 as an EIP Originator -> DXM (target) register. The EIP PLC will write data into register 1. For
local registers to be sent to the EIP controller, define registers as EIP DXM -> Originator. Use the Modify Multiple
Registers screen to change many registers parameters at one time.
The DXM1200 is big endian: the upper bits of a local register (15:8) are stored in the first byte of the assembly instance and
the second byte of the assembly instance is stored in the lower bits of a local register (7:0).
1 EttherNet/IP is a trademark of Rockwell Automation.

The following table shows DXM local registers 1, 5, and 10 being written from the EIP controller using assembly instance
112. Only registers 1, 5, and 10 are defined in the DXM Configuration Software as EIP Originator -> DXM registers.
Table 26: EIP Originator -> DXM register mapping
EIP Assembly Instance 112 DXM Local Registers
Adrs Data Adrs Data
00 11
01 11 22
01 22
02 33
05 33 44
03 44
04 55
10 55 66
05 66
The following table shows DXM local registers 10, 11, and 19 defined as EIP DXM -> Originator. The lower 2-bytes of each
register data is placed into assembly instance 100.
Table 27: EIP DXM -> Originator register mapping
EIP Assembly Instance 112 DXM Local Registers
Adrs Data Adrs Data
00 77
10 77 88
01 88
02 99
11 99 10
03 10
04 11
19 11 12
05 12
8.5 Setting up Email and Text Messaging

The DXM can be configured to send email or SMS messages based on threshold conditions.
Important: Only the DXM100 and DXM150 models offer SMS/text messaging capabilities.
Cellular-connected systems can use email or SMS. Ethernet-connected systems can only use email, but can send email to
cellular phones as a SMS message depending upon the network carrier. To send email to a Verizon phone, use the phone
number followed by @vtext.com, for example, [email protected].
For more information, refer to the DXM Configuration Software Instruction Manual (p/n 209933). Internal log files may be sent
using email. Follow these instructions and use the DXM Configuration Software to program the controller for email and/or
SMS.
1. On the Settings > System screen, set the Device Time on the DXM1200.
2. On the Settings > Cloud Services screen, select either Ethernet or Cell for the Push Interface.
3. If you selected Ethernet, configure your Ethernet connection by setting the IP settings on the Ethernet screen. If you
selected a Push interface of Cell, use the Cellular screen to define parameters.
4. Set the email and message parameters on the Notifications screen.
5. To send alert messages, define the threshold rule to use email and/or SMS.
6. To send log files, define the log file parameters.
8.5.1 Mail Server Authentication

Complete the mail server settings to have the DXM1200 send email alert messages or to email the log files.
The SMTP password is stored in the DXM1200, not the XML configuration file. Use the Settings > Notifications screen to
complete this configuration.

Figure 44. Mail server settings
After selecting Enable SMTP Authentication for the first time, a pop-up box appears with additional instructions to complete
the mail server authentication process.
After entering the user name and password, click on Send SMTP Password to save the user name and password to the
DXM1200. The DXM1200 must be connected to the PC to complete this operation. If successful, a pop-up window appears,
asking to reboot the device. Select Yes to reboot the device.
8.5.2 Define the Network Interface Settings

On the Cloud Services screen (shown with Show advanced settings selected), define the network connection settings by
selecting Ethernet or Cell from the Network Interface drop-down list. This determines how the DXM1200 sends data.
If you don't require pushing data to a web server, set the Cloud Push interval to zero.
Figure 45. Cloud Services screen
8.5.3 Configure your Ethernet Connection

To send email based on a threshold rule or to email log files, first define the network and email servers. When selecting
Ethernet, go to the Settings > Ethernet screen.
1. To define the Ethernet IP address, give the DXM1200 a static IP address. In most cases you may select the device to
use DHCP and have the IP address automatically assigned.
2. DNS settings are not typically required. The DXM1200 uses a public service to resolve Domain names, but if the
network connection does not have Internet access, the DNS settings may be required.

Figure 46. Settings > Ethernet screen
8.5.4 Configure your Cellular Connection

To use a cellular connection, select Cell as the network connection on the Settings > Cloud Services screen (see Configure
the DXM Controller for a Cellular Modem on page 34). The Cellular screen does not display unless the Network interface is
set to Cell.
Using a 4G LTE cell module requires a cellular plan; follow the instructions on p/n 205026 to activate a cell modem.
1. On the Settings > Cellular screen, select your cellular modem from the drop-down list.
2. Set the APN.
• If you are using a Banner 4G LTE Verizon Module (LE910), set the APN to vzwinternet.
• If you are using an Emnify 3G GSM Cellular Radio (HE910), set the APN to EM. This module does not require
an APN username or password.
• If you are using a third-party SIM card, the APN, APN Username, and Password must be provided by the
cellular service provider.
8.5.5 Set the Email and Messaging Parameters

From the Settings > Notifications screen, enter the SMTP definition, login, and password for a mail server.
Important: Only the DXM100 and DXM150 models offer SMS/text messaging capabilities.
To send email, you must supply the SMTP Server, Server Port, and login credentials. When you are only sending SMS
messages over cellular, the SMTP Server is not required.
The default SMTP port is 25 but may need to be adjusted for Ethernet-based networks. Note that many facilities block port
25. Port 587 is another common SMTP submission port.
The SMTP password is not stored in the XML configuration file, but on the DXM1200. After the password is entered, click on
Send SMTP Password to send it to the DXM1200. The password is stored in non-volatile memory, so reboot the DXM1200
to recognize the new password.
When using a GMail server, select Situational encryption and Enable SMTP authentication. The GMail server will not
allow you to send email alerts using the cellular interface. GMail may notify you that you must allow access for less secure
apps in your email settings.
For other email servers, the parameters may vary and will require information from the provider.

Figure 47. Mail and email settings
At the bottom of the screen, define the recipient to receive emails. These recipients selected in the threshold definition for
sending alert messages.
Sending SMS alerts requires that the Cellular Radio chip be installed and configured, regardless of the Push Interface used.
This setting allows a user to receive SMS alerts directly on their cell phone in the case of critical component changes or
failures.
1. On the Settings > Notifications screen, add recipients for SMS alerts.
2. In this section, you may change the Name of the recipient, add a phone Number, and insert a Message for the
recipient.
3. SMS alerts will be received in the format: Message Active/Inactive or Threshold Rule Name Active/Inactive
depending on the configuration.
4. Enter the phone numbers for SMS messages.
• 4G LTE cellular: Enter phone numbers without dashes. For example, a US phone number of (234) 555-1212
would be entered as 2345551212.
• Emnify GSM cellular: Enter phone numbers using the country code, area code, and phone number. For
example, a US phone number of (234) 555-1212 would be entered as 12345551212. These cellular modems
are not certified for use in the US.
8.5.6 Define Threshold Rules for Email

To define a threshold, go to Local Registers > Action Rules > Thresholds.
Depending upon which recipients are defined, select the appropriate email or SMS checkbox for the threshold rule (under
Email/SMS on state transition). When the threshold rules goes active or inactive, an email is generated.
For more information on how to set up threshold rules, refer to the DXM Configuration Software Instruction Manual (p/n
209933).
8.5.7 Define Log File Parameters for Emailing Log Files

The DXM1200 can email log files generated on the device.
Before emailing log files, set the Mail and Messaging parameters to provide the login credentials. When using Ethernet,
verify the IP address settings are defined on the Ethernet screen. Set the DXM1200 time, under Settings > System, so that
all data is properly time stamped.
Use the Local Registers > Local Registers in Use > Edit Register screen to select which registers to log which log file (set
the SD card logging to the log file. Define the setup of the log file using the Settings > Logging screen. Typical settings are
shown.
1. Enable the log and timestamp with every entry.
2. Enter the filename, log rate, and the maximum file size to send via email (5 to 10k is an efficient size for a cellular
connection). Banner does not recommend setting the log file size larger than 100 kB as this cannot be read through
the configuration software and must be read directly from the SD card.

3. Define the email address.

Figure 48. Defining the data log files
4. Define the local register data put into the log file using the Local Registers > Local Register Configuration screen,
under the Logging and Protocol Conversion section. From the SD Card Logging drop-down list, select the log file
to write to. Log files are written in CSV format.
5. Use the DXM Configuration Software to read back the log files. Under Settings > Logging, click Refresh List,
highlight the file to download, then click Save Selected.
8.6 Ethernet and Cellular Push Retries

The DXM1200 can be configured to send register data packets to a webserver. When the Ethernet or cell communications
path is not operating, the DXM1200 retries the send procedure. The communications retry process is outlined below for each
configuration.
Regardless of the communications type (Ethernet or cellular), a failed attempt results in the register data packet being saved
on the local micro SD card 2. The number of retries will depend upon the network connection type.
When there is bad cellular signal strength or there is no Ethernet connection, the transmission attempts are not counted as
failed attempts to send data. Only when there is a good network connection and there are 10 failed attempts will the
controller archive the data on the SD card. Data archived on the SD card must be manually retrieved.
8.6.1 Ethernet Push Retries

With an Ethernet-based network connection, the DXM1200 retries a message five times. The five retry attempts immediately
follow each other. After all attempts are exhausted, the register data packet is saved on the micro SD card.
At the next scheduled time, the DXM1200 attempts to send the saved packet as well as the newly created register data
packet. If it cannot send the new register data packet, the new register data packet is appended to the saved file on the micro
SD card to be sent later. After 10 rounds of retries, the data set is archived on the micro SD card under folder _sxi. No
additional attempts to resend the data are made; the data file must be manually retrieved.
Using SSL on Ethernet will have no retries, but will save each failed attempt to the micro SD card until 10 failed rounds. At
this time, the register data packet is archived.
8.6.2 Cellular Push Retries

In a cellular-connected system there are no retries. Failed transmissions are saved on the micro SD card.
After 10 successive failed attempts, the data is archived in the _sxi folder. Send attempts with a low signal quality are not
counted against the 10 count limit. For example, if the cellular antenna is disconnected for period that the DXM controller
would have sent 20 messages under normal circumstances, all 20 messages would be saved and will be retried when the
antenna is reconnected. If the signal quality was good, but the cellular network was not responding, the DXM1200 archives
the register data packets after 10 failed attempts.
8.6.3 Event/Action Rule or Log File Push Retries

Event-based pushes caused by Action rules and locally stored log files sent using email follow the same process when
failures occur, based on the network connection. The failed Event-based messages are resent with the next cyclical schedule
or the next event message that triggers a push message.
2 Enable HTTP logging to save data on the SD card; this is the factory default. See SETTINGS -> LOGGING in the DXM Configuration Tool.

8.6.4 Email and Text Message Push Retries

There are no retries for emails or SMS messages that fail to be sent from the DXM1200.

9 PROFINET®
PROFINET is a data communications protocol for industrial automation and processes. PROFINET IO defines how
controllers (IO controllers) and peripheral devices (IO devices) exchange data in real time. The standard is maintained by
PROFIBUS & PROFINET International (PI) , an organization headquartered in Karlsruhe, Germany.
Only the DXMR90, DXM700, DXM1000, and DXM1200 Controller models support PROFINET IO.
9.1 General Station Description Markup Language File

A PROFINET General Station Description (GSD) file is a description of an IO device provided by the device manufacturer in
an XML format (GSDML.xml).
The GSD file is a standardized way of describing the device information to engineering tools and the IO controller and can
work across a variety of tools as a standard set of device information.
9.2 DXM PROFINET IO Data Model

The PROFINET IO data model is based on the typical, expandable field device that has a backplane with slots. Modules
have different functionalities.
Modules are plugged into slots. In the PROFINET IO data model Slot 0, Subslot 1 is reserved for the Device Access Point
(DAP) or network interface.
• Inputs Integer Module sends integer data to the PLC
• Inputs Floats Module sends floating point data to the PLC
• Output Integer Module receives integer data from the PLC
9.3 Configure the DXM Controller for a PROFINET IO Connection

To use PROFINET, follow these instructions to configure the DXM700 or DXM1200.
1. Using the DXM Configuration Software, go to the Settings > Ethernet screen.
2. Select Enable PROFINET.
3. Save the configuration file and upload it to the DXM Controller (see Save and Upload the Configuration File on page
55).
After PROFINET is enabled, the IP address for the DXM Controller is controlled by the PROFINET host. The LCD
display and DXM Configuration Software no longer control the setting of the IP address. The PROFINET IP address
settings are invisible to the LCD display and the DXM Configuration Software.
The PROFINET data type and data size to/from the DXM Controller is configurable. The PROFINET data is processed from
the Local Register of the DXM Controller.
Configure the Local Registers to match the PROFINET module definitions in the host PLC.
9.3.1 Save and Upload the Configuration File

After making any changes to the configuration, you must save the configuration files to your computer, then upload it to the
device.
Changes to the XML file are not automatically saved. Save your configuration file before exiting the tool and before sending
the XML file to the device to avoid losing data. If you select DXM > Send XML Configuration to DXM before saving the
configuration file, the software will prompt you to choose between saving the file or continuing without saving the file.
1. Save the XML configuration file to your hard drive by going to the File > Save As menu.
2. Go to the DXM > Send XML Configuration to DXM menu.
Figure 49. Status indicator bar
• If the Application Status indicator is red, close and restart the DXM Configuration Tool, unplug and re-plug in the
cable and reconnect the DXM to the software.
• If the Application Status indicator is green, the file upload is complete.
• If the Application Status indicator is yellow, the file transfer is in progress.
The device reboots and begins running the new configuration.

9.4 Slots and Modules

There are nine slots to accommodate the DXM Controller data.
Table 28: Slots for input and output values
Values Slots Maximum Data Size
Input values 1–6 1440 bytes
Output values 7–9 1440 bytes
Table 29: Listing of slots for input and output values
PLC DXM Local Register Module Size

Slot
Module Definition Start End 512
Slot 1 Inputs Integer <- 1 256
Slot 4 Inputs Float <- 1001 1256
Slot 7 Output Integer -> 5001 5256
The DXM Local Register association shown uses a Module size of 512 bytes, which equals 256 Local Registers in the DXM.
Module sizes supported are 64, 128, 256 and 512 bytes. Input Integers are data from the DXM to the PLC. Output integers
are data from the PLC to the DXM.
Table 30: Slots 1 through 3
Module Notes
Input Integer 512 Allowed in slots 1-3, Module Identifier= 0x30
Module Notes
Input Float 512 Allowed in slots 4-6, Module Identifier= 0x34
Module Notes
Output Integer 512 Allowed in slots 7-9, Module Identifier= 0x40

Module Notes
Example Configuration
Table 33: Example configuration for slots and modules
Slot Module Description

Slot 1 Input Integer 512 The two input integer modules have a total of 640 bytes (320 Modbus registers)
Slot 2 Input Integer 128 The data will come from DXM Local Registers 1 through 320
The input Floating register module has a total of 128 byes (64 Modbus registers)
Slot 4 Input Float 128 Since it takes two Modbus registers to make a 32-bit floating value, there will be 32
floating point values coming from Local Registers 1001-1064
The output integer 64 module has a total of 64 bytes (32 Modbus registers).
Slot 7 Output Integer 64 The data will come from the PLC and be put into DXM Local Registers 5001 through
5032
9.5 Configuration Instructions
9.5.1 Install the GSD File

Although these instructions are specific for the Siemens TIA Portal (v14) software, you may use these instructions as a basis
for installing the GSD file into another controller.
1. Download the GSD file from www.bannerengineering.com.
2. Launch the Siemens TIA Portal (v14) software.
3. Click Open existing project.
4. Select a project and open it.
5. After the project is uploaded, click Devices & networks.
Figure 50. Devices and networks screen
6. Click Configure networks.

Figure 51. Configure networks screen
7. Click Options and select Manage general station description file (GSD).
The Install general station decription file window opens.
8. Click the More options (...) icon to the right of the Source path field and browse to the location the DXM GSD file
was downloaded to.
9. Select the DXM GSD file.
10. Click Install.
Figure 52. Hardware catalog
The system installs the DXM GSD file and places it in the Hardware catalog. In the example, the DXM GSD file is
located under Other field devices > PROFINET IO > Banner Engineering Corp. > Banner.
If the DXM GSD file does not install properly, save the log and contact Banner Engineering Corp.

9.5.2 Change the Device IP Address

Follow these instructions to change the IP address of the DXM device using the Siemens TIA Portal (v14) software. Use
these instructions as a basis if you are using another controller (PLC).
1. Launch the Siemens TIA Portal (v14) software.
2. Click Open existing project.
3. Select a project and open it.
4. Click Devices & networks.
Figure 53. Network view
The Network view displays.

5. Double-click on the DXM icon to open the Device view screen.
6. Click on the DXM icon in the graphic area of the Device view screen.
The Module properties window displays and the module can now be configured.
7. Click Properties.
8. Click General.
9. Select PROFINET Interface > Ethernet addresses.
Figure 54. Ethernet addresses
10. Select Set IP address in the project.

11. Enter the IP address.
12. Right-click on the device icon and select Online & diagnostics.

Figure 55. Online & diagnostics menu and screen
The Online & diagnostics windows displays.

13. Select Assign IP address under Functions.
14. Click Accessible devices.
The Select device window searches the network for available devices.
15. Determine the device to be adjusted via the MAC address and select it.
16. Click Apply.
The IP address for the device is updated.
17. Click Assign IP address to complete the step.
This step is completed for every device.
By default, each DXM shipped from the factory is assigned the IP address 192.168.0.1.
Immediately after the PROFINET protocol is enabled, the DXM has an IP address of 0.0.0.0. We recommend using the TIA
Portal to give the DXM an IP address so that the address is saved in the unit. When the PLC powers up, this IP address is
accessible. The PLC can change the IP address if it is configured to do so.
If the PLC assigns the DXM IP address (for example, using the Set IP address in the project option in Siemens TIA Portal),
the DXM receives the specified address, but only after the program has been loaded into the PLC and is running. If the DXM
is restarted after it was discovered and configured by the PLC, the DXM retains the IP address that was assigned to it using
the LCD or software until after the PLC discovers the DXM and assigns it the specified address again. However, if this
address is different than what is specified in the PLC, the DXM reverts to the address specified in the PLC after the PLC
becomes active again.
These configuration options conform to the PROFINET standard.
9.5.3 Change the Device Name

Follow these instructions to change the name of the DXM using the Siemens TIA Portal (v14) software. Use these
instructions as a basis if you are using another controller (PLC).
1. Open a project and click on Devices & networks.
The Network view displays.
2. Right-click on the DXM icon and select Assign device name.
The Assign PROFINET device name window displays. The software searches for devices of the same type.

3. Enter the desired name in the PROFINET device name field. Note that each name can be used only once.
4. Click Assign name.
The device now has a PROFINET name.

10 Accessories
For a complete list of all the accessories for the Sure Cross wireless product line, please download the Banner Industrial
Wireless Accessories list (p/n b_3147091).
Cordsets Power Supplies
MQDC1-506—5-pin M12, straight, single ended, 6 ft PSD-24-4—DC Power Supply, Desktop style, 3.9 A, 24 V DC, Class 2,
MQDC1-530—5-pin M12, straight, single ended, 30 ft 4-pin M12 quick disconnect (QD)
MQDC1-506RA—5-pin M12, right-angle, single ended, 6 ft PSDINP-24-06—DC power supply, 0.63 Amps, 24 V DC, with DIN Rail
MQDC1-530RA—5-pin M12, right-angle, single ended, 30 ft Mount, Class I Division 2 (Groups A, B, C, D) Rated
IVUC-E-406—RJ45 Ethernet to 4-pin threaded M8, straight, 6 ft PSDINP-24-13 —DC power supply, 1.3 Amps, 24 V DC, with DIN Rail
Mount, Class I Division 2 (Groups A, B, C, D) Rated
IVUC-E-415—RJ45 Ethernet to 4-pin threaded M8, straight, 15 ft
PSDINP-24-25 — DC power supply, 2.5 Amps, 24 V DC, with DIN Rail
Cellular Communications—Controllers accept Banner Cellular Modems Mount, Class I Division 2 (Groups A, B, C, D) Rated
only. Adding a cellular modem requires the placement of an internal cellular PSW-24-1—DC power supply with multi-blade wall plug, 100–240 V AC
antenna. Cellular modems are ordered separately as accessories under the 50/60 Hz input, 24 V DC 1 A output, UL Listed Class 2, 4-pin female
following part numbers: M12 connector
• LTE CAT1 Verizon (United States only): SXI-LTE-001
• LTE CAT-M1 AT&T (North America only): SXI-CATM1ATT-001
• LTE CAT-M1 Verizon (North America only): SXI-CATM1VZW-001

11 Product Support and Maintenance

11.1 File System and Archive Process
The DXM file system consists of two physical components: the serial EEPROM that stores non-volatile configuration
information and a removable micro SD card that stores file backup data and user created files.
EEPROM Files—The serial EEPROM stores basic data that is required to be non-volatile, including network configuration
data, IP address, MAC address, network masks, firewall settings, and authentication information. The controller XML
configuration file created by the DXM Configuration Software is stored in EEPROM. The small section of non-volatile local
registers is also stored in EEPROM.
Micro SD Card Files—The micro SD card contains most files at the root level. The archive directory contains files kept by
the system for history backup. Archive files are stored in the directory _sxi and are only accessible by removing the SD card.
• Data Log Files
• HTTP Push Files
• User created ScriptBasic file
• ScriptBasic program file
• CmVMon file
• _sxi Archive directory
Data Log files

Users may create up to four data log files using the DXM Configuration Software. The log files are stored in the root
directory on the SD card. When the file size limit is reached, the filename is changed to include the date and time
and the file is moved into the archive directory _sxi. If a finished log file is to be e-mailed, it will be done at this time
and then moved into the archive directory. Archived log files are deleted based on the Clear Logs parameter.
HTTP Push File
If the DXM1200 is configured to send data to a webserver or host system, the device creates an HTTP.LOG file on
the SD card. The HTTP log is created only if the Logging Interval is non-zero and the HTTP enable log is set. An
entry is placed in the HTTP log file at the Logging Interval specified by the user. At the Push Interval time, the HTTP
log file is sent to the webserver or host system. If the transmission is successful, the HTTP log file is time stamped
and placed into the archive directory (_sxi). If the transmission fails, the file remains in the root directory and
subsequent Logging Intervals are appended to the file and are sent at the next Push Interval. See Ethernet and
Cellular Push Retries on page 53.
User Created ScriptBasic Files
Users may use ScriptBasic to create files on the SD card by using the FILEOUT function. The filenames are fixed
and up to five files can be created in the root directory.
ScriptBasic Program File
The main ScriptBasic program that runs at boot time is stored on the SD card in the root directory.
CmVMon File
The CmVMon.txt file (Cellular milli-Volt Monitor) is created by the system and is used to track power events. Every
power-up cycle is date/time stamped with the voltage read from the I/O board. The value 24487 is equal to 24.487
volts. If the voltage drops below 11.2 V, another entry is put in the log file indicating the cellular modem will shut
down.
CM 2015-09-22 18:52:43 VMon Power entered normal range 24487
_sxi Archive Directory

Only two types of files are moved into the archive directory: data log files and HTTP log files. Data log files are date/
time stamped and placed into the archive directory when the size limit is reached. HTTP log files are date/time
stamped then placed into the archive directory when they are successfully sent to the webserver or host system. If
the HTTP log files were not successfully sent after the retries have been exhausted, the files are placed into a root
directory called sav.

11.2 Update Your DXM Processor Firmware Using the DXM

Configuration Tool
To update your processor firmware using the DXM Configuration Software, follow these instructions.
1. Using the DXM Configuration Software version 3 or later, connect to the DXM1200 via USB 3 or Ethernet.
File loads to the DXM1200 will take about 15 minutes using USB or approximately 2 minutes using Ethernet.
2. On the DXM Configuration Software, go to Settings > General > Device Information to verify the current firmware
version.
You must load a different version with the same firmware number for the boot loader to operate. Download firmware
files from the Banner website.
Figure 56. Device Information
3. Under Settings > Reprogram, click Select upgrade file to select the firmware file to program.
After the file load is completed, the DXM1200 restarts and loads the new firmware file. It takes about 2 minutes to complete
the programming process. The device reboots when finished. Verify the firmware has been updated, under Settings >
General > Device Information.
11.3 Clear the Password on DXM700-Bx, DXM1000-Bx, or DXM1200-

Bx Models
By default, the DXM Controllers do not require a password to load a configuration file. If a password is defined, the password
must be entered before uploading a configuration file.
To change the password, you must already know the current password. If you do not know the current password, follow
these steps to clear the password.
Important: Clearing the password erases the current configuration and any program files, log files, or
history files.
1. Turn on the power to the DXM Controller.

2. Set DIP switch 4 to the ON position.
3. Press and hold the processor button until processor board LED flashes.
4. Set DIP switch 4 to the OFF position.
5. Cycle power to the DXM Controller.
6. Reload the configuration file before resuming normal operation.
11.4 DXM1200 Documentation

• DXM Wireless Controller Sell Sheet, p/n 194063
• DXM1200-B1 Wireless Controller Datasheet, p/n 196719
• DXM1200-Bx Wireless Controller Instruction Manual, p/n 216539
• DXM ScriptBasic Instruction Manual, p/n 191745
• DXM Controller Configuration Quick Start, p/n 191247
• DXM Configuration Software v4 (p/n b_4496867)
• DXM Configuration Software Instruction Manual, p/n 209933
• DXM EDS Configuration file for Allen-Bradley PLCs
• Activating a Cellular Modem (p/n b_4419353)
• Additional technical notes and videos
3 While the file download is in process over a USB connection, do not use other applications on the PC. After the DXM1200 reboots for a firmware
update, the USB port may be unresponsive. Clear the connection by disconnecting the USB cable and restarting the DXM Configuration Software
software.

For more information about the DXM1200 family of products, including technical notes, configuration examples, and
ScriptBasic program examples, please refer to the Banner website: www.bannerengineering.com
11.5 DXM1200 Support Policy

The DXM Wireless Controllers are industrial wireless controllers that facilitate Industrial Internet of Things (IIoT) applications.
As a communications gateway, it interfaces local serial ports, local I/O ports, and local ISM radio devices to the Internet using
either a cellular connection or a wired Ethernet network connection. In a continuing effort to provide the best operation for the
DXM1200, stay connected with Banner Engineering Corp to hear about the latest updates through the Banner website.
Create a login today to stay informed of all Banner product releases.
11.5.1 Firmware Updates

The DXM1200 has been designed to be a robust and secure IOT device. To provide the most reliable and secure device
possible, periodic firmware updates are released to enhance and expand the capabilities of the DXM1200. Firmware updates
and description details are found on the Banner website. Customers with critical update requirements will get access to pre-
released firmware from the factory.
11.5.2 Website Information

The Banner website is the main method of disseminating DXM1200 information to customers. The data found on the website
include:
• DXM instruction manuals
• Configuration manuals
• Firmware downloads
• Firmware release notes
• Errata data, any known issues with a release of firmware
• Possible work-around solutions for known issues
• DXM Solutions Guides
11.5.3 Feature Requests

Our customer is our most valuable resource to improve our DXM1200. If you have suggestions for improvements to the
DXM1200 or configuration tools, please contact Banner Engineering Corp.
11.5.4 Potential DXM Issues

Potential issues with the DXM1200 are collected from Banner's support engineers to provide solutions. Users can get help
from the website documentation or by calling Banner Engineering for support help. Solutions are as simple as configuration
adjustments, work-around configuration solutions, or potential new firmware updates.
11.5.5 DXM Security

The DXM1200 was designed to collect local wireless sensor data, local sensor data, provide simple control, and send the
data to the cloud.
The DXM1200 does not run a Linux or Windows based operating system but an embedded real-time operating system
(RTOS) environment. As a proprietary operating system, the security aspects are easier to manage and minimize.
Security updates are released through the Banner Engineering Corp website (www.bannerengineering.com) and New
Product Release Announcements (NPRA).
11.6 Contact Us
Banner Engineering Corp. headquarters is located at:
9714 Tenth Avenue North
Minneapolis, MN 55441, USA
Phone: + 1 888 373 6767
For worldwide locations and local representatives, visit www.bannerengineering.com.

11.7 Mexican Importer

Banner Engineering de Mèxico, S. de R.L. de C.V.
David Alfaro Siqueiros 103 Piso 2 Valle oriente
San Pedro Garza Garcia Nuevo Leòn, C. P. 66269
81 8363.2714
11.8
Modelo (Model): DX80-2400—Este equipamento não tem direito à proteção contra interferência prejudicial e não pode
causar interferência em sistemas devidamente autorizados. Para maiores informações, consulte o site da ANATEL
www.gov.br/anatel/pt-br/
11.9 FCC and ISED Certification, 900 MHz, 1 Watt Radios

This equipment contains transmitter module RM1809.
FCC ID: UE3RM1809 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
IC: 7044A-RM1809 conditions: (1) this device may not cause harmful interference, and (2) this device must
HVIN: RM1809 accept any interference received, including interference that may cause undesired operation.
This device contains licence-exempt transmitters(s)/receiver(s) that comply with Innovation,
Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject
to the following two conditions: (1) This device may not cause interference, and (2) This
device must accept any interference, including interference that may cause undesired
operation of the device.
Cet appareil contient des émetteurs/récepteurs exemptés de licence conformes à la norme
Innovation, Sciences, et Développement économique Canada. L’exploitation est autorisée
aux deux conditions suivantes: (1) L’appareil ne doit pas produire de brouillage, and (2)
L’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d’en compromettre le fonctionnement.
FCC Notices
IMPORTANT: The transmitter modules RM1809 have been certified by the FCC / ISED for use with other products without
any further certification (as per FCC section 2.1091). Changes or modifications not expressly approved by the manufacturer
could void the user’s authority to operate the equipment.
IMPORTANT: The transmitter modules RM1809 have been certified for fixed base station and mobile applications. If
modules will be used for portable applications, the device must undergo SAR testing.
IMPORTANT: If integrated into another product, the FCC ID label must be visible through a window on the final device or it
must be visible when an access panel, door, or cover is easily removed. If not, a second label must be placed on the outside
of the final device that contains the following text:
Contains Transmitter Module RM1809
FCC ID: UE3RM1809
IC: 7044A-RM1809
HVIN: RM1809
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must accept any interference received, including interference that
may cause undesired operation.
Note
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna,
• Increase the separation between the equipment and receiving module,
• Connect the equipment into an outlet on a circuit different from that to which the receiving module is connected,
and/or
• Consult the dealer or an experienced radio/TV technician for help.
Antenna WARNING: This device has been tested with Reverse Polarity SMA connectors with the antennas listed in Table 34
on page 67. When integrated into OEM products, fixed antennas require installation preventing end-users from replacing
them with non-approved antennas. Antennas not listed in the tables must be tested to comply with FCC Section 15.203
(unique antenna connectors), FCC Section 15.247 (emissions), and ISED RSS-Gen Section 6.8.
FCC and ISED Approved Antennas

WARNING: This equipment is approved only for mobile and base station transmitting devices. Antenna(s) used for this
transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be collocated or
operating in conjunction with any other antenna or transmitter.
This radio transmitter module RM1809 have been approved by FCC and ISED Canada to operate with the antenna types
listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater
than the maximum gain indicated for any type listed are strictly prohibited for use with this device.
Table 34: Certified Antennas for 900 MHz 1 Watt
Model Number Antenna Type Maximum Gain Impedance Minimum Required Cable/
Connector Loss
- Integral Antenna Unity gain 0
BWA-9O1-x Omni, 1/4 wave dipole ≤2 dBi 50 Ω 0
BWA-9O2-C Omni, 1/2 wave dipole, Swivel ≤2 dBi 50 Ω 0
BWA-9O6-A Omni Wideband, Fiberglass Radome ≤8.2 dBi 50 Ω 2.2 dB
BWA-9O5-B Omni Base Whip ≤7.2 dBi 50 Ω 1.2 dB
BWA-9Y10-A Yagi ≤10 dBi 50 Ω 4 dB
11.10 FCC and ISED Certification, 2.4GHz

This equipment contains transmitter module DX80-2400 or SX243.
FCC ID: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
UE300DX80-2400 conditions: (1) this device may not cause harmful interference, and (2) this device must accept
IC: 7044A-DX8024 any interference received, including interference that may cause undesired operation.
FCC ID: UE3SX243 This device contains licence-exempt transmitters(s)/receiver(s) that comply with Innovation,
IC: 7044A-SX243 Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to
HVIN: DX80G2 / the following two conditions: (1) This device may not cause interference, and (2) This device
DX80N2 / SX243 must accept any interference, including interference that may cause undesired operation of the
device.
Cet appareil contient des émetteurs/récepteurs exemptés de licence conformes à la norme
Innovation, Sciences, et Développement économique Canada. L’exploitation est autorisée aux
deux conditions suivantes: (1) L’appareil ne doit pas produire de brouillage, and (2) L’utilisateur
de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d’en compromettre le fonctionnement.
FCC Notices
IMPORTANT: The transmitter modules DX80-2400 and SX243 have been certified by the FCC / ISED for use with other
products without any further certification (as per FCC section 2.1091). Changes or modifications not expressly approved by
the manufacturer could void the user’s authority to operate the equipment.
IMPORTANT: The transmitter modules DX80-2400 and SX243 have been certified for fixed base station and mobile
applications. If modules will be used for portable applications, the device must undergo SAR testing.

IMPORTANT: If integrated into another product, the FCC ID/IC label must be visible through a window on the final device or
it must be visible when an access panel, door, or cover is easily removed. If not, a second label must be placed on the
outside of the final device that contains the following text:
Contains Transmitter Module [DX80-2400 or SX243]
FCC ID: [UE300DX80-2400 or UE3SX243]
IC: [7044A-DX8024 or 7044A-SX243]
HVIN: [DX80G2, DX80N2 or SX243]
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must accept any interference received, including interference that
may cause undesired operation.
Note
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna,
• Increase the separation between the equipment and receiving module,
• Connect the equipment into an outlet on a circuit different from that to which the receiving module is connected,
and/or
• Consult the dealer or an experienced radio/TV technician for help.
Antenna Warning: This device has been tested with Reverse Polarity SMA connectors with the antennas listed in Table 35 on
page 68. When integrated into OEM products, fixed antennas require installation preventing end-users from replacing them
with non-approved antennas. Antennas not listed in the tables must be tested to comply with FCC Section 15.203 (unique
antenna connectors), FCC Section 15.247 (emissions), and ISED RSS-Gen Section 6.8.
FCC and ISED Approved Antennas

WARNING: This equipment is approved only for mobile and base station transmitting devices. Antenna(s) used for this
transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be collocated or
operating in conjunction with any other antenna or transmitter.
The radio transmitter modules DX80-2400 and SX243 have been approved by FCC and ISED Canada to operate with the
antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a
gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.
Table 35: Certified Antennas for 2.4 GHz
Model Antenna Type 2.4 GHz Radio Module Maximum Gain Impedance
Integral antenna DX80-2400 Unity gain
BWA-2O2-C Omni, 1/2 wave dipole, Swivel DX80-2400 or SX243 ≤ 2 dBi 50 Ω
BWA-2O2-D Omni, Dome, Box Mount DX80-2400 ≤ 2 dBi 50 Ω
BWA-2O2-E Omni, 1/4 wave dipole, Swivel DX80-2400 ≤ 2 dBi 50 Ω
BWA-2O5-C Omni, Collinear, Swivel DX80-2400 ≤ 5 dBi 50 Ω
BWA-2O5-MA Omni, full-wave dipole, NMO DX80-2400 ≤ 4.5 dBi 50 Ω
BWA-2O6-A Omni, Dome, Box Mount DX80-2400 ≤ 6 dBi 50 Ω
BWA-2O7-C Omni, Coaxial Sleeve, Swivel DX80-2400 ≤ 7 dBi 50 Ω
11.11 Warnings
Install and properly ground a qualified surge suppressor when installing a remote antenna system. Remote antenna
configurations installed without surge suppressors invalidate the manufacturer's warranty. Keep the ground wire as short as
possible and make all ground connections to a single-point ground system to ensure no ground loops are created. No surge
suppressor can absorb all lightning strikes; do not touch the Sure Cross® device or any equipment connected to the Sure
Cross device during a thunderstorm.

Exporting Sure Cross® Radios. It is our intent to fully comply with all national and regional regulations regarding radio
frequency emissions. Customers who want to re-export this product to a country other than that to which it was sold
must ensure the device is approved in the destination country. The Sure Cross wireless products were certified for use
in these countries using the antenna that ships with the product. When using other antennas, verify you are not exceeding
the transmit power levels allowed by local governing agencies. This device has been designed to operate with the antennas
listed on Banner Engineering’s website and having a maximum gain of 9 dBm. Antennas not included in this list or having a
gain greater that 9 dBm are strictly prohibited for use with this device. The required antenna impedance is 50 ohms. To
reduce potential radio interference to other users, the antenna type and its gain should be so chosen such that the equivalent
isotropically radiated power (EIRP) is not more than that permitted for successful communication. Consult with Banner
Engineering Corp. if the destination country is not on this list.
Important: Please download the complete DXM1200-Bx Wireless Controller technical documentation,
available in multiple languages, from www.bannerengineering.com for details on the proper use,
applications, Warnings, and installation instructions of this device.
Important: Por favor descargue desde www.bannerengineering.com toda la documentación técnica de los
DXM1200-Bx Wireless Controller, disponibles en múltiples idiomas, para detalles del uso adecuado,
aplicaciones, advertencias, y las instrucciones de instalación de estos dispositivos.
Important: Veuillez télécharger la documentation technique complète des DXM1200-Bx Wireless

Controller sur notre site www.bannerengineering.com pour les détails sur leur utilisation correcte, les
applications, les notes de sécurité et les instructions de montage.
WARNING:
• Do not use this device for personnel protection
• Using this device for personnel protection could result in serious injury or death.
• This device does not include the self-checking redundant circuitry necessary to allow its use in
personnel safety applications. A device failure or malfunction can cause either an energized (on)
or de-energized (off) output condition.
Important:
• Never operate a 1 Watt radio without connecting an antenna
• Operating 1 Watt radios without an antenna connected will damage the radio circuitry.
• To avoid damaging the radio circuitry, never apply power to a Sure Cross® Performance or Sure
Cross MultiHop (1 Watt) radio without an antenna connected.
Important:
11.12 Banner Engineering Corp. Limited Warranty

Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp. will
repair or replace, free of charge, any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty period. This
warranty does not cover damage or liability for misuse, abuse, or the improper application or installation of the Banner product.
THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE OF
DEALING OR TRADE USAGE.
This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING CORP. BE
LIABLE TO BUYER OR ANY OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL,
CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY PRODUCT DEFECT OR FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER
ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE.
Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligations or liabilities relating to any product
previously manufactured by Banner Engineering Corp. Any misuse, abuse, or improper application or installation of this product or use of the product for personal protection
applications when the product is identified as not intended for such purposes will void the product warranty. Any modifications to this product without prior express approval by
Banner Engineering Corp will void the product warranties. All specifications published in this document are subject to change; Banner reserves the right to modify product
specifications or update documentation at any time. Specifications and product information in English supersede that which is provided in any other language. For the most
recent version of any documentation, refer to: www.bannerengineering.com.
For patent information, see www.bannerengineering.com/patents.

Index
A D
authentication 45, 46 DXM S
configure for cell 34
save
C configuration file 55
H scheduler 44, 45
cell modem
activate CAT M1 34 holiday event 45
activate Verizon 4G LTE 34 U
configure DXM 34 M
upload
install 31, 32 Modbus registers 8 configuration file 55
purchase 31, 32
configuration file
save 55 O W
upload 55 one-time event 44 webserver authentication 45, 46
create
weekly event 44
holiday event 45 R
one-time event 44
weekly event 44 registers 8

DXM1200 BX

Uploaded by

Copyright:

Available Formats

DXM1200 BX

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

DXM1200 BX

Uploaded by

Copyright:

Available Formats

Sure Cross® DXM1200-Bx Wireless

8.1.2 Create a One-Time Event ......................................................................................................................................................44

1 DXM1200-Bx System Overview

I/O Connectivity Logic Controller User Interface

Local Registers Type Description

1–845 32-bit integer Local data registers

846–849 32-bit integer Reset, Constant, Timer

851–900 32-bit non-volatile integer Data flash, non-volatile

901–1000 Reserved for internal use

1001–5000 Floating point Floating point registers, local data registers

5001–7000 32-bit integer Local data registers

7001–8000 32-bit non-volatile integer Data flash, non-volatile

> 10000 Read only virtual registers, system-level data

Figure 2. DXM1200 Controller Figure 3. DXM1200E Controller

M12 D-Code for Ethernet

4 www.bannerengineering.com - Tel: + 1 888 373 6767

Wired Connectivity Wireless Connectivity

Wireless Radio Networks

Performance Wireless Radio Network MultiHop Wireless Radio Network

Register Mapping Scheduler

www.bannerengineering.com - Tel: + 1 888 373 6767 5

User programmable LCD API Interface

1.1 DXM1200 Models

Blank = Low profile housing Blank = None

B1 = Modbus controller for data aggregation of

Figure 4. DXM1200-B1 model Figure 5. DXM1200E-B1 model

1.2 DXM Hardware Configuration Overview

6 www.bannerengineering.com - Tel: + 1 888 373 6767

Figure 6. DXM1200 base board

Cellular Antenna Placement

*SIM card is located on the underside of installed modem

1.3 DXM Automation Protocols

1.4 DXM Modbus Overview

www.bannerengineering.com - Tel: + 1 888 373 6767 7

Processor/Outputs (Base Board)

Ethernet Local Regi sters Gateway or MultiHop

Modbus Data Traffic

1.4.1 DXM Modbus Registers

Modbus Slave ID Device

199 Local Registers—Internal storage registers of the DXM1200

Local Registers Type Description

1–845 32-bit integer Local data registers

846–849 32-bit integer Reset, Constant, Timer

851–900 32-bit non-volatile integer Data flash, non-volatile

901–1000 Reserved for internal use

1001–5000 Floating point Floating point registers, local data registers

5001–7000 32-bit integer Local data registers

8 www.bannerengineering.com - Tel: + 1 888 373 6767

Local Registers Type Description

7001–8000 32-bit non-volatile integer Data flash, non-volatile

> 10000 Read only virtual registers, system-level data

Modbus Register LED Color State

1102 : bit 0 LED 1 Red

1103 : bit 0 LED 2 Green

1105: bit 0 Backlight

1.5 DXM Configuration Software

DXM Configuration Software

This configuration file governs all aspects of the DXM1200 operation.

www.bannerengineering.com - Tel: + 1 888 373 6767 9