b=h 8 in

Perimeter, p 32 in
2.67 ft

Depth Layer, ΔL cu cu Cu/ Pa α

ft ft Ton/ ft2 lb/ ft2 (Table 9.10)
5 to 10 5 0.478 1070.72 0.5 0.65
10 to 15 5 0.364 815.36 0.4 0.74
15 to 20 5 0.581 1301.44 0.7 0.55
20 to 25 5 0.372 833.28 0.4 0.74
25 to 30 5 0.134 300.16 0.2 0.92
30 to 35 5 0.134 300.16 0.2 0.92
35 to 40 5 0.134 300.16 0.2 0.92
40 to 45 5 0.36 806.4 0.4 0.74
45 to 50 5 0.36 806.4 0.4 0.74
50 to 55 5 0.47 1052.8 0.5 0.65
55 to 60 5 0.47 1052.8 0.5 0.65
α.c.p.ΔL
ton
4.14
3.59
4.26
3.67
1.64
1.64
1.64
3.55
3.55
4.07
4.07
35.84

14.3366933333333
Depth Rl Rl SPT qu cu f d=0.8f tand
m m ft N-Values kN/m2
0.0 0.0 0.0 0 0.00 0.00 27.1 21.7 0.4
5.0 5.0 16.4 26 185.25 92.63 32.8 26.2 0.5
10.0 5.0 16.4 37 439.38 219.69 37.5 30.0 0.6
15.0 5.0 16.4 37 439.38 219.69 36.1 28.9 0.5
20.0 1.0 3.3 37 439.38 219.69 35.2 28.1 0.5
5.0 5.0 16.4 43 510.63 255.31 42.7 34.1 0.7
6.0 1.0 3.3 43 510.63 255.31 41.7 33.3 0.7
7.0 1.0 3.3 43 510.63 255.31 40.9 32.7 0.6
8.0 1.0 3.3 43 510.63 255.31 40.3 32.2 0.6
9.0 1.0 3.3 43 510.63 255.31 39.7 31.8 0.6
10.0 1.0 3.3 43 510.63 255.31 39.3 31.4 0.6
11.0 1.0 3.3 85 1062.50 531.25 49.1 39.3 0.8
12.0 1.0 3.3 85 1062.50 531.25 48.3 38.6 0.8
1. Pile specifications
Pile type
Outer pile diameter D=
Cross-sectional area Ap =
Outer perimeter u=

2. Estimation of unit shaft and end bearing resistance

Shaft resistance fs = min (2*N1,60, 200 kPa) for co
fs = min (5*a*N
a = 0.55 if c
End bearing resistance
qb = min (Nb*min(40*Lp/D,380)
Nb: SPT N values for soil ab

3. Factor of safety for estimation of allowable pile capacity, FS=3

Unit weight Effective

Bulk
(Cohesionless stress at Factors for corection of SPT N-Values
Density
soil) tip
SPT α
Avg N- Values kN/m3 kN/m3 kPa CN CH CR CS
0.0 16.0 6.0 0.00 0.55 0.00 0.6 0.95 1
13.0 17.5 7.5 37.41 0.55 1.33 0.6 0.95 1
21.0 19.5 9.5 84.99 0.55 1.06 0.6 0.95 1
25.0 19.5 9.5 132.56 0.55 0.91 0.6 0.95 1
27.4 19.5 9.5 180.14 0.55 0.80 0.6 0.95 1
36.0 20.1 10.1 28.86 0.55 1.42 0.6 0.95 1
39.4 20.1 10.1 38.95 0.55 1.32 0.6 0.95 1
40.6 20.1 10.1 49.03 0.55 1.24 0.6 0.95 1
41.8 20.1 10.1 59.12 0.55 1.18 0.6 0.95 1
43.0 20.1 10.1 69.20 0.55 1.12 0.6 0.95 1
43.0 20.1 10.1 79.29 0.55 1.08 0.6 0.95 1
51.4 24.5 14.5 93.79 0.55 1.02 0.6 1 1
59.8 24.5 14.5 108.29 0.55 0.98 0.6 1 1
 Pushed Pile
1.80 m
2.545 m2
1.220 m

min (2*N1,60, 200 kPa) for cohesionless soils

min (5*a*N1,60, 200 kPa) for cohesion soils
a = 0.55 if cu < 150 kPa, otherwise: a = 0.55 - 0.1*(cu/100 - 1.5)

min (Nb*min(40*Lp/D,380),18000 kPa)

Nb: SPT N values for soil above 10D and 4D below the pile tip

Ult.pile
of SPT N-Values Correction of SPT qb fs (cohesionless) Qs Qb capacity,
Qu
CB N60 Avg N60 N1,60 kPa kPa kN kN kN
1 0.0 0.0 0.00 0.0 0.0 0.0 0.0 0.0
1 14.8 12.4 19.72 1372.2 39.4 240.6 127.6 368.2
1 35.2 20.0 37.13 4433.3 74.3 693.5 412.3 1105.8
1 35.2 23.8 31.90 7916.7 63.8 1082.7 736.3 1818.9
1 35.2 26.0 28.30 9891.4 56.6 1151.7 919.9 2071.6
1 40.9 34.2 57.90 3800.0 115.8 1858.1 353.4 2211.5
1 40.9 37.4 53.81 4990.7 107.6 1989.4 464.1 2453.5
1 40.9 38.6 50.66 5999.8 101.3 2113.0 558.0 2671.0
1 40.9 39.7 48.10 7059.6 96.2 2230.4 656.5 2886.9
1 40.9 40.9 45.95 8170.0 91.9 2342.5 759.8 3102.3
1 40.9 40.9 44.09 9077.8 88.2 2450.1 844.2 3294.3
1 85.0 51.4 86.98 12564.4 174.0 2662.3 1168.5 3830.8
1 85.0 59.8 82.89 15946.7 165.8 2864.6 1483.0 4347.6
 Allowable Allowable
Point Line Line
Bearing Bearing
Spring Spring Spring
capacity, Qu capacity, Qu
kN Ton kip/ft kip/ft kip/ft
0.0 0.0
122.7 13.8 39.55983 40.261
368.6 41.4 114.0386 99.14723
606.3 68.1 178.0342 161.8671
690.5 77.6 946.935 888.9991
737.2 82.9 305.5412 226.292
817.8 91.9 1252.042 1635.647 1247.823
890.3 100.1 1505.205 1737.277 1356.703
962.3 108.2 1771.079 1833.781 1460.121
1034.1 116.2 2049.663 1925.969 1559.246
1098.1 123.4 2277.404 2014.428 1654.837
1276.9 143.5 3152.128 2188.914 1343.549
1449.2 162.9 4000.649 2355.203 1481.109
1. Pile specifications
Pile type
Pile size D=
B=
Cross-sectional area Ap =
Outer perimeter u=

f'c =
Fy =
Ag =
99% of pile area =
Bar Diameter =
Ab =
No; of bars =
As =
Allowable Capacity =
0.33f'cAc =
0.39fyAs =
Pa =

Ultimate Capacity (from soil-pile interaction) =

SF =
Allowable Capacity (from soil-pile interaction) =

Number of Piles (required) n=

DL + LL =
5 % for Pile Cap =
n=

Minimum Length of pile =

Grid 3
Number of Piles (required) n=
DL + LL =
5 % for Pile Cap =
n=

Minimum Length of pile =

Grid 1
Number of Piles (required) n=
DL + LL =
5 % for Pile Cap =
n=

Minimum Length of pile =

 Pushed Pile
8 in
8 in
64 sq. in
32 in

3000 psi
50000 psi
64 in^2
63.4 in2
16 mm
0.31 in2
4 nos
1.2 in2
0.33f'cAc + 0.39fyAs
62726.4 lb 28.00286
24318 lb 10.85615
87044 lb
39 Tons

36 Tons
2.5 (2.5 - 4)
13 Tons

DL + LL / Pa piles
792 Tons
831.6 Tons
62.4 Piles

20 ft

DL + LL / Pa piles
75.39 Tons
79.164435 Tons
5.3 Piles

60 ft

DL + LL / Pa piles
48 Tons
50.4 Tons
3.9 Piles

20 ft
Bored Pile
Pushed Pile
Driven Pile

TABLE: Design Reactions

Story Joint Label
Unique Name
Load Case/Combo FX FY DL LL Wall
tonf tonf tonf tonf tonf
BASE 1 1 DEAD 0.0689 0.1085 23.39 7.49 12.1
BASE 2 3 DEAD -0.0169 0.0225 23.76 6.64 17.2
BASE 3 5 DEAD 0.0907 -0.0415 31.17 10.82 27.5
BASE 4 7 DEAD 0.1041 -0.0148 31.54 10.93 28.4
BASE 5 9 DEAD 0.379 -0.0054 33.18 14.24 22.8
BASE 6 11 DEAD 0.0178 0.029 23.61 6.16 16.6
BASE 7 13 DEAD -0.0337 -0.0296 25.74 8.19 21.6
BASE 8 15 DEAD -0.1996 -0.0388 32.22 11.39 29.4
BASE 9 17 DEAD -0.185 -0.0571 32.47 11.62 29.4
BASE 10 19 DEAD -0.2752 0.06 33.07 12.18 29.2
BASE 11 134 DEAD 0.0264 -0.0498 30.17 11.08 21.1
BASE 12 135 DEAD 0.0235 0.0171 29.54 10.70 18.4
326.6 121.4 273.7
Finishing Suspended Rain Total
tonf tonf tonf tonf
2.6 2.5 0.2 48.4315
2.7 0.9 0.2 51.48
5.4 0.0 0.4 75.39
5.5 0.0 0.5 45.23
5.1 1.6 0.3 44.01
3.2 -0.1 0.3 26.13
4.1 0.0 0.3 34.22
5.7 0.0 0.5 46.97
5.7 0.1 0.5 47.27
4.9 1.0 0.3 47.58
4.8 0.8 0.4 38.25
4.4 2.0 0.3 35.78
54.0 8.9 4.2 788.8