GROUP

Model : UTN

High reading accuracy due to

large size and design of dial

Loading accuracy as high as + 1%

Motor driven threaded columns for quick &

effortless adjustment of lower cross-head-to
facilitate rapid fixing of test specimen
Features : Hydraulic Controls :
Loading accuracy as high as + 1% Hand operated wheels are used to control the flow to and from the
Suitable at variable speeds to suit a wide range of materials. hydraulic cylinder. The regulation of the oil flow is infinitely variable.
Continuous roll autographic recorder supplied as standard to Incorporated in the hydraulic system is a regulating valve, which
enable study of the behavior of materials. maintains a practically constant rate of piston movement.
Motor driven threaded columns for quick effortless adjustment Control by this valve allows mechanical extensometer reading to be
of lower cross-head-to facilitate rapid fixing of test specimen. taken.
High reading accuracy due to large size and design of dial. Principle of operation for-
Wide range of standard and special accessories, including load Model : UTN
stabilizer.
Operation of machine is by hydraulic transmission of load from the test
Easy change from plain to threaded and screwed specimens. specimen to a separately housed load indicator.
Large effective clearance between columns enables testing of
The hydraulic system is ideal since it replaces transmission of load
standards specimens as well as structures.
through levers and knife edges, which are prone to wear and damage due
Simple controls for ease of operation. to shock on rupture of test pieces.
Robust straining frame of an extremely rigid construction. Load is applied by a hydraulically lubricated ram.
Safe operation ensured by means of safety devices. Main cylinder pressure is transmitted to the cylinder of the pendulum
Fully enclosed and protected pendulum. dynamometer system housed in the control panel.
Load Capacity : 100 kN, 200kN, 400kN, 600kN, 1000kN.
The cylinder of the dynamometer is also of self-lubricating design.
Application : The load transmitted to the cylinder of the dynamometer is transferred
'FIE' Analogue Universal Testing Machine is designed for testing Ferrous through a lever system to a pendulum.
& Non-Ferrous materials under tension, compression bending, Displacement of the pendulum actuates the rack and pinion mechanism
transverse and shear loads. Hardness test on metals can also which operates the load indicator pointer and the autographic recorder.
conducted. The deflection of the pendulum represents the absolute load applied
on the test specimen.
Machine Consists of -
Return movement of the pendulum is effectively damped to absorb
Straining unit : energy in the event of sudden breakage of a specimen.
This consists of a hydraulic cylinder, motor with chain and sprocket drive
and a table coupled with the ram of the hydraulic cylinder, mounted on to Load indicator System :
a robust base. This system consists of a large dial and a pointer.
The cylinder and the ram are individually lapped to eliminate friction. The A dummy pointer is provided to register the maximum load reached
upper cross-head is rigidly fixed to the lower table by two strengthened
during the test.
columns. The lower cross-head is connected to two screwed columns
which are driven by a motor. Axial loading of the ram is ensured by Different measuring ranges can be selected by operating the range
relieving the cylinder and ram of any possible side loading by the selection knob.
provision of ball seating. An overload trip switch is incorporated which, automatically cuts out the
An displacement scale, with a minimum graduation of 1mm, is provided pump motor when the load range in use is exceeded.
to measure the deformation of the specimen.
Tension test is conducted by gripping the test specimen between the Displacement :
upper and lower cross-heads. An elongation scale, with a minimum graduation of 1mm, is provided to
Compression, transverse, bending, shear and hardness tests are measure the deformation of the specimen.
conducted between the lower cross-head and the lower table.
The lower cross-head can be raised or lowered rapidly by operating the Pendulum Dynamometer :
screwed columns, thus facilitating ease of fixing of the test specimen.
This unit permits selection of favorable hydraulic ratios producing
Control Panel : relatively small frictional forces.
The Control Panel consists of a power pack complete with drive motor Pressurized oil in the loading cylinder pushes up the measuring piston
and an oil tank, control valves, load indicator system & autographic proportionately and actuates the special dynamometer system.
recorder. The piston is constantly rotated to eliminate friction.
Power Pack : The dynamometer system is also provided with an integral damper and
The power pack generates the maximum pressure of 200 kgf/cm2. The ensures high reliability of operation.
hydraulic pump provides continuously non-pulsating oil flow. Hence the The load transmitted to the dynamometer is transferred through a
load application is very smooth. pendulum to the load indicator.

Attachments :

Attachment for Tension Test of - Attachment for Tension Shear Test

Shouldered & Threaded specimens upto Test of - Wire Ropes (Min. Ø5 to Ø20mm) &
M6 to M20 (Min. length 110 mm). (Min. Ø1 to Ø10mm) (Min.Ø25 to Ø40mm
Technical Specifications for - Analogue Universal Testing Machine
Model – UTN

MODEL UNIT UTN 10 UTN 20 UTN 40 UTN60 UTN 100

Maximum Capacity kN 100 200 400 600 1000
1stMeasuring range kN 0-100 0-200 0-400 0-600 0-1000
Minimum Graduations kN 0.2 0.4 1 1 2
2 nd Measuring range kN 0-50 0-100 0-200 0-300 0-500
Minimum Graduations kN 0.1 0.2 0.5 0.5 1
3 rd Measuring range kN 0-25 0-50 0-100 0-120 0-250
Minimum Graduations kN 0.05 0.1 0.25 0.2 0.5
4 th Measuring range kN 0-10 0-20 0-40 0-60 0-100
Minimum Graduations kN 0.02 0.04 0.1 0.1 0.2
Clearance for tensile test
mm 50-700 50-700 50-700 50-800 50-850
(At fully descended working piston)
Clearance for compression test
mm 0-700 0-700 0-700 0-800 0-850
(At fully descended working piston)
Clearance between columns mm 500 500 500 600 750
Ram Stroke mm 150 200 200 250 250
Straining/ Piston Speed (at no load) mm/min 0-300 0-150 0-150 0-100 0-80
CONNECTED LOAD
Power for UTN HP 1.3 1.3 2.3 2.5 3.5
V 400-440 400-440 400-440 400-440 400-440
3 3 3 3 3
STANDARD ACCESSORIES
FOR TENSION TEST UTN
Clamping jaws for round specimens 10-20 10-20 10-25 10-25 10-25
of diameter mm 20-30 20-30 25-40 25-40 25-45

Clamping jaws for flat specimens 0-10 0-10 0-15 0-15 0-22
of thickness mm 10-20 10-20 15-30 15-30 22-44
Width mm 50 50 65 70 70
FOR COMPRESSION TEST
Pair of Compression Plates of diameter. mm 120 120 120 120 160
FOR TRANSVERSE TEST
Table with adjustable rollers
width of rollers mm 160 160 160 160 160
Diameter of Rollers mm 30 30 30 50 50

Maximum clearance between supports mm 500 500 500 600 800

Radius of punch tops mm 6,12 6,12 12,16 16,22 16,22

Due to constant R& D specifications & features are subject to change without notice.
Colour scheme subject to confirm at the time of order.
 Series : UTN

Manufactured By :

Plot No. 68 & 89, Parvati Co-op Industrial Estate, YADRAV-416 145 (Ichalkaranji),
Tal : Shirol, Dist : Kolhapur, Maharashtra State, INDIA.

Tel : +91 2322 252137, Cell : +91 98223 94981, E-mail : mrk@fietest.com
Web : www.fiegroup.in, www.fietest.com, www.fuelinstrument.com