HAT560N Series

(HAT560N /HAT560NB)

ATS CONTROLLER
HAT560N series ATS controller is intelligent dual-supply module with configurable function, automatic
measurement, LCD display, and digital communication. It combines digital, intelligence and networking.
Automatic measurement and control can reduce incorrect operation. It is an ideal option for ATS.
The powerful Microprocessor contained within the unit allows for precision voltage
(2-way-3-phase/single phase) measuring and make accurate judgment; in addition, the corresponding
digital output port will active when there is over/under voltage, over/under frequency, loss of phase and
other abnormal condition occurs. This controller has full consideration in various application of ATS
(automatic transfer system) and can be directly used for specialized ATS, Contactor ATS, Air break ATS
etc. It has compact structure, advanced circuits, simple wiring and high reliability, and can be widely
used in electrical devices, automatic control and testing system of electric power, telecommunications,
petroleum, coal, metallurgy, railways, municipal administration, intelligent building, etc.

PERFORMANCE AND CHARACTERISTICS

1) System type can set as: Mains (1#) & Generator (2#), Generator (1#) & Mains (2#), Mains (1#) &
Mains (2#), Generator (1#) & Generator (2#).
2) 132x64 LCD with backlight, optional Chinese and English display, push-button operation.
3) Measure and display 2-way 3 phase Voltage and Frequency:
1# 2#
Line voltage (Uab, Ubc, Uca) Line voltage (Uab, Ubc, Uca)
Phase voltage (Ua, Ub, Uc) Phase voltage (Ua, Ub, Uc)
Frequency Hz Frequency Hz
4) Over/under voltage, loss of phase, reverse phase sequence, over/under frequency protection.
5) Automatic/Manual mode. In manual mode, can force the switch to close or open;
6) All parameters can be set on site. With Two different passwords which ensures authorized staff
operation only.
7) During commissioning, the genset can be set either on On-load or Off-load mode.
8) ATS Controller has function of automatic Re-closing.
9) Closing output signal can be set as on intervals or as continuous output.
10) Applicable for ATS of one neutral position, two neutral position and non-position.
11) Applicable for 2 isolated neutral line.
12) Real-time clock (RTC).
13) Event log can record 50 items circularly.
14) Scheduled start & stop generator (can be set as start genset once a day/week/month whether with
load or not).
15) Can control two generators to work in a cycle, even the genset running time and crank rest time
can be set.
16) Optional AC system or DC system.
17) With standard LINK communication interface. With "remote controlling, remote measuring, remote
communication" function by the ModBus communication protocol. Can remote start/stop the
genset and remote control the ATS to close or open.
HAT560N Series ATS Controller 2016-06-27 Version 1.0
 18) Can check the current status of controller (digital input port, digital output port, over voltage, under
voltage, over frequency, under frequency etc.).
19) Suitable for various AC systems (3 phase 4-wires, 3-phase 3-wires, single-phase 2-wire, and
2-phase 3-wire).
20) Modular design, self extinguishing ABS plastic shell, pluggable terminal, built-in mounting，
compact structure with easy installation.
HAT560N series controller and its main functions are shown as following,
Function
Type DC Power Supply AC Power Supply AC Current/Power
HAT560N √ × ×
HAT560NB √ √ (LN220V) ×

HAT560N Series ATS Controller 2016-06-27 Version 1.0

 SPECIFICATION
Items Contents
1. DC 8.0V~35.0V, continuous power supply.
Operating Voltage
2. AC170V~270V during AC power L1N1/L2N2 supply.
Power Consumption <3W (Standby mode: ≤2W)
AC system HAT560N HAT560NB
3P4W (ph-N) AC30V~AC360V AC170V~AC277V
3P3W (ph-ph) AC60V~AC620V Not used
AC Voltage Input
1P2W (ph-N) AC30V~AC360V AC170V~AC277V

2P3W (ph-N) AC30V~AC360V AC170V~AC277V

Rated Frequency 50/60Hz
Close Relay Output 16A AC250V Volts free output
Auxiliary Relay Output 1 7A AC250V Volts free output
Auxiliary Relay Output 2 7A AC250V Volts free output
Auxiliary Relay Output 3 16A AC250V Volts free output
Auxiliary Relay Output 4 16A AC250V Volts free output
Digital Input GND connect is active.
Communication LINK interface, MODBUS Protocol
Case Dimensions 139mmx120mmx48mm
Panel Cutout 130mmx111mm
Temperature: (-25~+70)°C;
Working Conditions
Humidity: (20~93)%RH
Storage Condition Temperature: (-25~+70)°C
Protection Level IP55 Gasket
Apply AC2.2kV voltage between high voltage terminal and low voltage
Insulation Strength terminal;
The leakage current is not more than 3mA within 1min.
Weight 0.62kg

HAT560N Series ATS Controller 2016-06-27 Version 1.0 Page 6 of 27

OPERATING
OPERATION PANEL

KEY FUNCTION DESCRIPTION

I# Manual Close In Manual mode, switch on 1# power to load.

Open In Manual mode, switch off 1# or 2# power to off-load.

II# Manual Close In Manual mode, switch on 2# power to load.

Manual/Auto Set Press the button and controller enter into Manual or Auto mode.

Press the button to enter into menu interface; pressing and holding it to
Menu /Confirm return to the main menu interface. When an alarm occurs, pressing and
holding the button for more than 3s can remove alarm.
Scroll the screen. In parameter setting, pressing this button can
decrease values.
Scroll Screen Pressing and holding the button for more than 3s, there is a flash on the
/Increase backlight to confirm the “always illuminated” mode is selected.
Pressing and holding the button for more than 3s again, the backlight
will extinguished which means the “normal display” mode is selected.

HAT560N Series ATS Controller 2016-06-27 Version 1.0

 LCD DISPLAY
MAIN SCREEN

U1(L-L) 380 380 380V

U2(L-L) 380 380 380V This screen shows: 1#/2# line voltage (L1-L2, L2-L3,
F1 50.0Hz F2 50.0Hz and L3-L1), frequency, controller’s working status,
Present Status: MANUAL close/open information and load information.

U1(L-N) 220 220 220V

U2(L-N) 220 220 220V This screen shows: 1# and 2# 3 phase Voltage (L-N),
2016-06-27 (1) 09:43:36 real-time clock, controller’s working status, close/open
Present Status: MANUAL information and load information.

1# Under Volt First line: 1# working status

2# Volt normal Second line: 2# working status
Gens Start signal Out Third line: other working status
Present Status: AUTO Fourth line: alarm type and information.
Fifth line: close/open information and load information

Display of the #1 status (upper to lower)

No. Item Type Description
1 1# Gens Alarm Alarm When 1# genset failure occurs, this will display.
2 1# Fail to Close Alarm When 1# close failure occurs, this will display.
3 1# Fail to Open Alarm When 1# open failure occurs, this will display.
When 1# power supply voltage has exceeded the set
4 1# Over Voltage Indication
value, this will display.
5 1# Loss of Phase Indication Loss of any phase of A, B and C.
When 1# power supply frequency is higher than the set
6 1# Over Freq Indication
value, this will display.
When 1# power supply frequency has fallen below the
7 1# Under Freq Indication
set value, this will display.
When 1# power supply voltage has fallen below the set
8 1# Under Volt Indication
value, this will display.
1# Phase Sequence
9 Warning Phase sequence is not A-B-C.
Wrong
10 1# Volt Normal Indication 1# power supply voltage is within the setting range.

HAT560N Series ATS Controller 2016-06-27 Version 1.0

Display of the #2 status (upper to lower)

No. Item Type Description

1 2# Gens Alarm Alarm When 2# genset failure occurs, this will display.
2 2# Fail to Close Alarm When 2# close failure occurs, this will display.
3 2# Fail to Open Alarm When 2# open failure occurs, this will display.
When 2# power supply voltage has exceeded the
4 2# Over Voltage Indication
setting value, this will display.
5 2# Loss of Phase Indication Loss of any phase of A, B and C.
When 2# power supply frequency is higher than the set
6 2# Over Freq Indication
value, this will display.
When 2# power supply frequency has fallen below the
7 2# Under Freq Indication
set value, this will display.
When 2# power supply voltage has fallen below the set
8 2# Under Volt Indication
value, this will display.
2# Phase Sequence
9 Warning Phase sequence is not A-B-C.
Wrong
10 2# Volt Normal Indication 2# power supply voltage is within the setting range.

Display status of the other items (upper to lower)

No. Item Type Description
1 Trip Alarm Alarm Trip alarm input is active.
2 Breaking Compulsorily Warning Breaking compulsorily input is active.
3 Gens Start Out Indication Start input is active.
4 Remote Start Input Indication This input is active when start the genset circularly.

HAT560N Series ATS Controller 2016-06-27 Version 1.0

DESCRIPTION OF CONNECTING TERMINALS

Terminal description,
No. Functions Description Remark
Connected with negative of starter
1 B- DC input B-
battery.
Connected with positive of starter
2 B+ DC(8-35)V; Power supplied by controller.
battery.
3
Aux. output 1 Default: 1# open output Relay contact output; Volts free; Rated 7A
4
5 Normally Close Default: Gen Start
6 Aux. output 2 COM Output (Normally Relay contact output; Volts free; Rated 7A
7 Normally Open Open)
8 Normally Close
Default: ATS
9 Aux. output 3 COM Relay contact output; Volts free; Rated 16A
Power A
10 Normally Open
11 Normally Open
Default: ATS
12 Aux. output 4 COM Relay contact output; Volts free; Rated 16A
Power N
13 Normally Close
14 Relay contact output; Volts free; Rated 16A
1# Close Output Relay contact output; Volts free;
15
16 Relay contact output; Volts free; Rated 16A
2# Close Output Relay contact output; Volts free;
17
18 A1
19 B1
1# AC System 3P4W voltage input For single phase, only connect A1, N1
20 C1
21 N1

HAT560N Series ATS Controller 2016-06-27 Version 1.0

No. Functions Description Remark
Detect the 1# ATS closing status.
22 1# Close Input Ground connected is active.
Auxiliary contact input.
Detect the 2# ATS closing status.
23 2# Close Input Ground connected is active.
Auxiliary contact input.
24 Aux. Input 1 User-defined. Ground connected is active.
25 Aux. Input 2 User-defined. Ground connected is active.
26 COM GND
27 A2
28 B2
2# AC System; 3P4W voltage input For single phase, only connect A2, N2
29 C2
30 N2
Communication Used for PC communication/
LINK
port program updating.

HAT560N Series ATS Controller 2016-06-27 Version 1.0

 HAT560N Series ATS Controller User Manual
18 INSTALLATION

19 FAULT FINDING
Symptom Possible Solutions
Controller no response with
Check starting batteries;
power.

If SG72 module is fitted, check its connections.

LINK communication failure
Check module address in parameters settings.

Check auxiliary output connections, pay attention to normally open

Auxiliary Output Error contact and normally close contact.
Check the output settings in parameters settings.

Ensure that the auxiliary input is soundly connected to GND when it’s
active, while hung up when it is inactive.
Auxiliary Input Abnormal
( Note: The input port will be possibly destroyed when connected with
voltage)

Check ATS.
Genset running while ATS
Check the connection wirings between the controller and the ATS.
not transfer
Ensure that the ATS Neutral position whether is same as the setting.

HAT560N Series ATS Controller 2016-06-27 Version 1.0 Page 27 of 27