Basaveshwar Engineering College Bagalkot (Autonomous).

Department of Mechanical Engineering

First C.I.E. Test (Even semester)-2021-2022
Course B.E. Semester 06
Subject Heat Transfer
Subject Code UME 623C
Division(s) B
Time 05:00 pm to 06:00 pm
Date 02-05-2022 Max Marks 30
Faculty Name Dr.H.M.Kadlimatti
Answer two full questions.
Use of Heat and Mass Transfer data book is
permitted.
Marks BL CO
Qla Consider a solid cylinder of radius r = b and height z = c. The
06 L3 CO1
boundary surface at r = b is subjected to a uniform heating
electrically at a rate of qo W/m2, the boundary surface at z = o is
insulated. The boundary surface at z c dissipates heat by
=

convection into an ambient at zero temperature with a heat transfer

coefficient h. Write the mathematical formulation of this heat
conduction problem.
b An electrical resistance of mattress type is inserted between two
09 L4 CO1
slabs of different materials on a panel heater. On one side, the
material has a thermal conductivity of 0.174 W/m K and 10 mm
thick. On the other side of the heater the material has a thermal
conductivity of 0.05 W/m K and 25 mm thick. The convection heat
transfer coefficients for the thinner and thicker slabs are 23.26 and
11.63 W/m2K. The temperature of the surrounding air on both
sides is 15 °C. If the energy dissipation for each square meter of the
mattress is 5 kW, neglecting end effects, find i) the surface
temperature of the slab ii) the temperature of the mattress
assuming it to be the same as the inner surface of the slabs
Q2 a Discuss the importance of critical thickness of insulation from the 06 L2 COO1
heat transfer point of view with suitable examples.
b Calculate the rate, at which heat is being lost to the surroundings, 09 L4 CO1
per unit length of a steam pipe (k 80.2 w/m K) of ID 3 cm and OOD
3.4 cm. The convective heat transter coetficients on inner and outer
surfaces are 20 W/m2 K each. There is a radiation heat transfer
coefficient of 5 W/m2 K on the outer surface in addition. The
temperature of steam is 150 °C and outside air temperature is 25
C.
Q3a A wire 150 mm long and 0.5 mm in diameter is taut between two 06 L3 CO1
conducting supports in a water tank and is submerged. A controlled
amount of current through a variac is passed through the wire until
the water boils at 100 °c. Find the steady sate temperature of the
wire if 25 watts of electric power is consumed. Take h = 6000 W/m2
C
Develop an expression to find the 3-D heat diffusion from an 09 L4 CO1
arbitrary shaped solid body which is generating heat of its own from
fundamentals.
 Basaveshwar Engineering College (Autonomous) Bagalkote
Department of Mechanical Engineering
Second CIE Test (Even semester)-2021-2022
B.E Semesteer 06
Course
Heat Transfer Division (s) B
Subject Time 10:30 am to 11:30 am
Subject Code UME 623C
09-06-2022 Max Marks 30
Date
Faculty Name Dr.H.M.Kadlimatti
Answer two full questions.
is Permitted
Use of Heat and Mass transfer data handbook
Marks BL CO
for flow of fluid at 06 L2 CO2
Compare velocity and thermal boundary layers
a
Q1. a
a temperature T» with
convective heat transfer coefficient h' over a
flat plate of length L' maintained at a temperature of Ts.
b Hot air at atmospheric pressure and 80 °C enters an 8 m long 09 L4 CO03
uninsulated square duct of cross section 0.2 m x 0.2 m that
house at a rate of 0.15 m3/s. The D= A - 4 barv)
passes through the attic of a
the P
duct is observed to be nearly isothermal at 60 °C. Determine 2024bD2
rate of heat loss from the duct to the attic space.

Q2. a State whether the flow is laminar or turbulent for the following 06 L2 CO3
cases

A 10 long yatcht sailing at 13 km/h in sea water (p =

i m
1000 kg/m3 and u = 1.3 x 10-3 kg/ms)

A compressor disc of radius 0.3 rotating at 15000 rpm in

i)
air at 5 bar and 400 °C
b A steel ball of diameter D' is removed from a domestic refrigerator 09 L4 C02
which is at a temperature of 0 °C and placed on a table in a room.
The room air temperature is maintained at 40 °C. Develop an
expression to determine total1 heat transfer rate from the
fundamentals.

the Nusselt number for laminar 06 L3 CO3

Q3. a An approximate expression for
flow along a flat plate in the thermal layer is given by
Nu-b-0.332P/Re/2. Develop an expression for the relation
between the local and average heat transfer coefficient.
09 L4 CO2
b Vertical pipe 5 cm in diameter carrying hot water is exposed to
ambient air at 15 °C. If the outer surface of the pipe is 65 °C, find
the heat loss from one-meter length of pipe per hour.
 Basaveshwar Engineering College (Autonomous) Bagalkote.
Department of MechanicalEngineering
Third CIE Test (Even semester)-2021-2022
Course B.E. Semester :06
Subject :Heat Transfer Division (s) :B
Subject Code :UME 623C Time :10:30 am to 11:30 am
Date :05-07-2022 Max Marks :30
Faculty in charge Dr.H.M.Kadlimatti

Answer two full questions.

Use of HMT data handbook and steam tables is permitted

Marks BL CO

Q1. a Develop an expression to find the LMTD of a counter flow 06 L3 CO3

exchanger from fundamentals.
bA vertical square plate 30 cm x 30 cm is exposed to steam at 09 L4 CO4
atmospheric pressure. The plate temperature is 98°C. Determine
the mass of steam condensed per hour.

Q2. a Show that, the intensity of radiation for a diffuse surface is same 06 L3 CO4
in all the directions.
b A tubular heat exchanger is to be designed for cooling oil from a 09
L5 CO3
temperature of 80 °C to 30 °C by large stagnant water which may
be assumed to remain at a constant temperature of 20 °C. The
heat transfer surface consists of 30 cm long straight tube of 20
mm diameter. The oil (Cp 2.5 kJ/kg K, Sp.gr
= =
0.8) flows through
the cylindrical tube with an average velocity of 50 cm/s. Determine
the overall heat transfer coefficient for the oil cooler.

Q3. a Assuming the sun to be a black body having surface

temperature 06 L3 CO4
of 5800 K. Determine the i) total emissive
power ii) wavelength at
which the maximum spectral intensity occur and ii) the maximum
value of monochromatic emissive power.
b Water is to be boiled at atmospheric
pressure in a polished copper 09 L4 CO04
pan by means of an electrical heater. The bottom of the copper
pan
is 0.4 m diameter and is kept at 120 °C. Determine the rate
at
which the water will evaporate from the
pan due to boiling.