SESSION PLAN

Sector ELECTRICAL AND ELECTRONICS

Qualification ELECTRICAL INSTALLATION MAINTENANCE NCII
Unit of Competency PERFORM ROUGHING IN ACTIVITIES, WIRING AND CABLING WORKS FOR
SINGLE PHASE DISTRIBUTION, POWER, LIGHTING AND AUXILIARY SYSTEM
Module Title PERFORMING ROUGHING IN ACTIVITIES, WIRING AND CABLING WORKS FOR
SINGLE PHASE DISTRIBUTION, POWER, LIGHTING AND AUXILIARY SYSTEM

Learning Outcomes:
At the completion of the module, the trainees must be able to:
1. Install electrical metallic /non-metallic (PVC conduit)
2. Install wire ways and cable tray
3. Install auxiliary terminal cabinet and distribution panel
4. Prepare for cable pulling and installation
A. Introduction:
This module covers the knowledge, skills and attitudes on installing electrical metallic and non-metallic
conduit, wire ways and cable clamp, auxiliary terminal cabinet and distribution frame panel board/safety switch and
used in roughing-in based on the required performance standards. This unit also covers the outcomes required in
preparing for cable pulling and installation, performing wiring and cabling lay-out and notifying completion of work for
single-phase distribution, power, lighting and auxiliary systems.
B. Learning Activities
LO 1. Install electrical metallic /non-metallic (PVC conduit)
Learning Content Methods Presentation Practice Feedback Resources Time
1.1-1 mechanical Lecture/ Trainers discusses 2hrs.
drawing and electrical Discussion mechanical drawing Compare
wiring diagram and electrical wiring answer to
interpretation diagram interpretation Answer self-
answer
check 1.1-1
Read information sheet key 1.1-1
Individual
4.1-1 “mechanical
Study
drawing and electrical
 wiring diagram
interpretation”

1.1-2 Proper uses of

safety harness (PPE) Trainer discusses
Lecture/
Proper uses of safety 2hrs.
Discussion Answer self- Compare
harness (PPE)
check,1.1-2 answers to
answer
Individual Read information sheet key 1.1-2
Study 1.1-2 “Proper uses of
safety harness (PPE)”
1.1-3 Types of Trainer discusses Answer self- Compare
Lecture/
electrical conduit types of electrical check,1.1-3 answers to
Discussion
conduit answer
Individual Read information sheet key 1.1-3
Study 1.1-3 “Types of
electrical conduits”
1.1-4 Proper uses and Laptop 3hrs
Trainer discusses
installation of Lecture/ Projector
Proper uses and
conduits Discussion Whiteboard
installation of conduits Compare
Marker
Answer self- answer to
Read information
check 1.1-4 answer
sheet 1.1-3 “Proper
Individual key 1.1-4
uses and Installation
Study
of conduits”

Demonstration Trainer demonstrate Perform task Refer to

the proper uses and sheet 1.1-4 performan
Installation of conduits ce criteria
 1.1-4
1.1-5 Technics in Trainer discusses the Laptop
installing and technics in installing Projector
Lecture/
bending electrical and bending electrical Whiteboard
Discussion
metallic and non- metallic and non- Compare Marker
metallic conduits metallic conduits Answer self- answer to
Read information check 1.1-5 answer CBLM
Individual sheet 1.1-5 “Technics key 1.1-5
Study in installing and 2hrs.
bending electrical
metallic and non-
metallic conduits”
Trainer demonstrate Perform task Refer to
the technics in sheet 1.1-5 performan
Demonstration installing and bending ce criteria
electrical metallic and 1.1-5
non-metallic conduits
1.1-6 Types of fittings Trainer discusses the
and their uses Individual different type of fitting Compare
Study and their uses Answer self- answer to
Individual Read information check 1.1-5 answer
Study sheet 1.1-6 “Types of key 1.1-5
fittings and their uses”
LO 2. Install wire ways and cable tray
1.2-1 Trainer’s discusses Answer self- Compare Laptop 6hrs.
Install wire ways and check 4.2-1 answer to Projector
Lecture/ answer Whiteboard
cable tray
Discussion key 4.2-1 Marker

Individual Read information sheet CBLM

Study 4.2-1“Install wire ways
and cable tray”
 Perform Refer to
job sheet performan
Trainer’s demonstrate
4.2- ce criteria
Demonstration on how to Install wire
1“Install 4.2-1
ways and cable tray
wire ways
and cable
tray”
LO 3. Install auxiliary terminal cabinet and distribution panel
4.3-1 Lecture/ Trainer’s discusses Laptop
Discussion tack welding procedure Projector
Whiteboard
Marker
Compare CBLM
answer to
Answer self-
Individual Read information sheet answer
check 4.3-1
Study 4.3-1 “1. Install key 4.3-1
auxiliary terminal
cabinet and
distribution panel” 20 hrs.

Perform job Refer to

sheet 4.3- performan
1“1. Install ce criteria
Trainer’s demonstrate auxiliary 4.3-1
Demonstration
1. Install auxiliary terminal
terminal cabinet and cabinet and
distribution panel distribution
panel”
LO 4. Prepare for cable pulling and installation
4.4-1 Lecture/ Trainer’s discusses Answer self- Compare Laptop 3 hrs.
 Prepare for cable Projector
pulling and installation Whiteboard
Discussion
Marker
answer to
CBLM
check 4.4-1 answer
Read information sheet
key 4.4-1
Individu 4.4-1 “Prepare for cable
al Study pulling and installation”

Trainer’s demonstrate Perform job Refer to

1. Prepare for cable sheet 4.3- performan
Demonst pulling and installation 1“1. ce
ration “Prepare for criteria
cable 4.3-1
pulling and 2hrs.
installation
”

C. Assessment Plan
 Written examination
 Performance test of the job sheets.
 Interview/Oral questioning
Prepared by:

ENGR. MARK NEL A. INOJOSA

Trainer