Hyponic-003 COMPLETE CATALOG

Hyponic®
Hypoid Right Angle

Gearmotor and Reducer
CATALOG 12.001.50.004
Hyponic ® Hypoid Right Angle
Gearmotor and Reducer
Sumitomo’s patented Hyponics are

high-performance reducers and
gearmotors that feature
all-steel hypoid gearing.
Proven Performance in a
Full Range of Ratios
Over one million Hyponic drives in service worldwide.
Ratios from 5:1 to 1440:1 available.
100
Extremely Quiet Operation
Smooth, silent operation is a benefit of hypoid gearing. 90
Hyponic
Efficiency (%)
Patented Compact Design: 80
More Torque Delivered 70

Offset design and all-steel gearing transmit more torque than
other designs. 60
Worm
Maintenance Free: Extraordinary Reliability 50
5
Gears
Trouble-free grease lubrication, no oil level to maintain, 25 50 75 100 150
no oil changes. 200 250
Reduction Ratio
Universal Housing Design Minimizes Spares
Modular housing design accommodates hollow output shaft,
solid output shaft, flange mounted and foot mounted designs. Outstanding Efficiency Saves
Adaptable Money
Integral motorized, C-face adaptor and free input shaft styles Efficiencies far higher than worm gearing. Highly effi-
enable users to optimize their selections. cient across all ratios. No cooling fans are required, ever.
Two-Year Warranty Hyponic hypoid gearing demonstrates efficiencies of

Not limited by operational hours or duty cycle. 85-90% within the range of 10 to 240:1.
www.sumitomodrive.com
Hyponic Table of Contents
Page Page
Nomenclature.............................................................2 Technical Information ...........................................D-1
Basic Information and Shaft Dimensions............................................D-2
Recommendations ....................................................4 Shaft Rotation .................................................D-3
Hyponic Gearmotors..............................................A-1 Actual Reduction Ratio ...................................D-4
Product Range ................................................A-2 Allowable Overhung Load...............................D-5
Standard Specifications ..................................A-4 Moment of Inertia............................................D-6
Gearmotor Selection Flowchart Construction and Nameplate ..........................D-7
and Procedure ............................................A-5
Output Shaft Safety Cover Dimensions ..........D-8
AGMA Load Classifications ............................A-7
Torque Arm.....................................................D-8
Motor Thermal Ratings ...................................A-9
Mounting .......................................................D-10
Hollow Shaft Type Selection Tables
Lubrication ....................................................D-12
3-Phase Motor ..........................................A-10
Paint and Rust Proofing Specifications.........D-12
Single-phase Motor ..................................A-17
Motor Information
Inverter Duty .............................................A-19
Conduit Box Mounting Direction ..............D-14
Hollow Shaft Type Dimensions
Motor Cover Mounting Specifications.......D-14
3-Phase Motor ..........................................A-22
Conduit Box Dimensions ..........................D-15
Single-phase Motor ..................................A-27
Standard Motor Characteristics................D-16
Inverter Duty .............................................A-29
Assembly Drawings..................................D-18
Hyponic Speed Reducers......................................B-1
Motor Thermal Ratings.............................D-19
Product Range, Standard Specifications
and Recommended Service Factors ..........B-2 Brakemotor Characteristics ......................D-20
AGMA Load Classifications ............................B-3 Standard Wiring Connection ....................D-22
Reducer Selection Flowchart Assembly of Brakemotors ........................D-23
and Procedure ............................................B-4 Standards
Reducer Selection Tables Motor Protection ...........................................D-26
1750 RPM...................................................B-6 International Standards and Corresponding
1450 RPM...................................................B-8 Sumitomo Standards................................D-27
1165 RPM.................................................B-10 EC Directives and CE Marking .....................D-29
980 RPM...................................................B-12 Precautions for Inverter Driving ....................D-31
870 RPM...................................................B-14 Constant Torque Operation of General
Purpose Motors ........................................D-32
720 RPM...................................................B-16
General Engineering Information
580 RPM...................................................B-18
Basic Power Transmission Formulas ...........D-34
50 RPM.....................................................B-20
Formula Derivations......................................D-36
Reducer Dimensions
Common Conversion Factors .......................D-37
Frame Size 1120~1520Y..........................B-22
Frame Size 1230~1531Y..........................B-23
Hyponic Gearmotor and Reducer
Options.............................................................C-1
Plug-in Solid Output Shaft ..............................C-2
Plug-in Solid Output Shaft,
Foot Mounted .............................................C-3
Output Flange .................................................C-4
Nomenclature & Mounting Positions
The complete Hyponic® is specified by the use of 14 references.
1 2 3 4 5 6 7 8 9 10 11 12 13 14
R N Y M S 05 1 2 2 0 A AV X1 B 38
Ratio
Frame size
Brake
Gearmotor HP (1750 rpm)
Optional Specification suffix
(as required)
Special feature
Motor Specification
Input connection
Mounting style AGMA class (gearmotor only)
Output shaft orientation Shaft specification
Hyponic product code O/P shaft direction (shafted model only)
TABLE 1 HYPONIC PRODUCT CODE TABLE 7 MODEL SIZE

PREFIX TYPE Frame Size
R Hypoid Gear 361 1120
461 1220
TABLE 2 OUTPUT SHAFT ORIENTATION 56 1320
PREFIX TYPE 60 1420
63 1520
Universal Direction
N
(Maintenance Free) 64 1230
1330
1430
TABLE 3 MOUNTING STYLE
1530
PREFIX TYPE
1531
Y Shaft Mount (Hollow Shaft)
F Flange (Solid Shaft)

TABLE 8 OUTPUT SHAFT DIRECTION (Shafted Model Only)
H Foot (Solid Shaft)
L Projects to Left Side
R Projects to Right Side
TABLE 4 INPUT CONNECTION
T Projects to Both Left/Right Sides
PREFIX
INPUT CONNECTION WHEN VIEWED FROM MOTOR END
REDUCER W/MOTOR
M Integral Motor
J JM C-Face Adaptor
TABLE 9 SHAFT SPECIFICATIONS
SUFFIX OUTPUT SHAFT INPUT

TABLE 5 MODIFICATION
SYMBOL HOLLOW SOLID SHAFT
PREFIX
Y Key (Inch) Inch Inch
S Special Key (Metric) Metric Metric
Standard
TABLE 10 AGMA CLASS (Integral Motor Type Only)

TABLE 6 GEARMOTOR HP (APPLIES ONLY TO 1750 RPM)
CAPACITY CAPACITY SUFFIX CLASS
HP (kW) HP (kW)
SYMBOL SYMBOL A I
01 1/8 (0.1) 1H 1 1/2 (1.1) B II
02 1/4 (0.2) 2 2 (1.5) C III
03 1/3 (0.25) 3 3 (2.2)
05 1/2 (0.4) 5 5 (3.7)
08 3/4 (0.55) 8 7 1/2 (5.5)
1 1 (0.75)
Hyponic
2
TABLE 11 MOTOR SPECIFICATIONS TABLE 14 STANDARD NOMINAL REDUCTION RATIOS
SUFFIX SPECIFICATION STANDARD RATIOS

AV AF Motor (ADJ Frequency) 5 20 60 200 560
SG Single Phase Motor 7 25 80 240 750
Three Phase Motor 10 30 100 300 900

12 40 120 360 1200
15 50 150 480 1440
TABLE 12 OPTIONAL SPECIFICATIONS SUFFIX
(as required)
SUFFIX SPECIFICATION NOMENCLATURE EXAMPLES:
RNYJ 1220Y 5
HOLLOW BORE OPTIONS
R Hyponic 1220 Model Size
Extended Flange (for motor clearance)
N Universal Mount Y Inch
Y Shaft Mount (Hollow Shaft) 5 Ratio
F1 Left (Viewed from J C-Face Input
motor end)
RNFM05 1220L YA J1 20
R Hyponic 1220 Model Size
G1 Right (Viewed from
motor end) N Universal Mount L Left O/P Shaft Direction
F Flange Mount (Solid Shaft) YA Y: Inch, A: AGMA Class I
M Integral Motor J1 Bolt-on Feet, Bottom
SOLID SHAFT OPTIONS
05 1/2 HP 20 Ratio
When ordering, the following information should be included:
X1 Plug-in Shaft
Motor Specification (230/460 VAC 60 Hz is supplied, unless otherwise specified)
NEMA frame size for C-face adaptor
Plug-in Shaft with Bolt-on Feet
Optional conduit box positions must be specified, otherwise the standard position is
supplied.
J1 Bottom
S1 Opposite from
Motor
M1 Top
Plug-in Shaft with Extended Flange

(for motor clearance)
P1 Left (Viewed from

motor end)
Q1 Right (Viewed from

motor end)
TABLE 13 BRAKE (Gearmotor Only)
SUFFIX SPECIFICATION
B With Brake
No Brake
Hyponic
3
Basic Information & Recommendations
General Service Factors
Selection of the Hyponic® speed reducer should be based on In general, gear drives are rated for a specific application by
actual horsepower and torque requirements at the output shaft. the use of Service Factors. Each application has its own
Contrary to conventional gear reducers, the Hyponic® speed conditions and operating requirements. There are three load
reducer has very high efficiencies over a wide range of reduction classifications: uniform, moderate shock and heavy shock.
ratios. Proper selection frequently permits the use of reduced These are further classified into duration of service per day and
input power requirements without sacrificing torque at the output the prime mover. (See Table 15 below and Load Classification
shaft. tables on pages A-7 ~ A-8 for Gearmotors and page B-3 for
Drive Ratings Reducers.)
Standard Hyponic® speed reducers are designed and built Time of operation, frequency, and severity of shock must be
for long, maintenance-free, 10-hour daily service under determined in order to select the properHyponic® reducer
conditions of uniform loads (equivalent to AGMA service factor for a specific application. To assist in the selection process,
1.0). When your application involves more severe conditions, AGMA has defined standard Service Factors.
catalog ratings must be divided by the proper S.F., or the The Hyponic® reducer has higher overload capacity than
actual load must be multiplied by this factor. conventional speed reducers as a result of the tooth shape,
greater number of teeth in contact, and the high material
quality of the components.
Table 15 Recommended Reducer Service Factors

LOAD CLASSIFICATIONS
PRIME MOVER DURATION OF SERVICE UNIFORM MODERATE SHOCK HEAVY SHOCK
AGMA AGMA AGMA
Occasional 1/2 hr. per day *0.50 *0.80 1.25
Intermittent 3 hrs. per day *0.80 1.00 1.50

ELECTRIC
MOTOR
Up to 10 hrs. per day 1.00 1.25 1.75
24 hours per day 1.25 1.50 2.00
*Maximum momentary or starting load must not exceed 250% of gear reducer rating (rating meaning service factor of 1.0). Time sp
ecified
for occasional and intermittent service refers to total operating time per day.
Excessive Overloads example, coupling connections normally involve torsional forces

Hyponic® Speed Reducers provide 250% momentary only. However, when power is transmitted through spur gears,
intermittent shock load capacity and are warranted for belts, pulleys or chains, both torsional and radial forces may be
2 years from date of shipment. Refer to our standard terms applied to the slow speed shaft. When driving through helical or
and conditions for our complete warranty. bevel gears, all three conditions (torsional, radial and thrust load)
may be referred to the reducer shaft.
Selection for Applications Involving Shock Loading The slow speed shaft and bearings must have sufficient strength
For applications involving frequent start-stop, braking or to withstand these loads, and it is, therefore, necessary to
reversing, or quick starting of load having large inertia, consult determine the allowable limits for each condition.
factory for model selection or recommended modifications.
Load Centering
Allowable Radial and Thrust Loads The radial load capacities are calculated with the load
The loads imposed on the slow speed shaft vary with the concentrated at the midpoint of the slow speed shaft extension.
method of connecting the shaft to the driven machine. Radial load capacities decrease if the center of the load is
Frequently, in addition to torsional forces, radial and thrust loads moved farther from the reducer and the values obtained from the
are applied to the slow speed shaft at the same time. For charts must be adjusted accordingly.
Hyponic
4
Shaft Connections Warranty
Pulley, sprocket or sheave connection Mount any Sumitomo warrants that its Hyponic® Speed
of the above as close to the unit housing as possible, Reducers will deliver their continuous catalog ratings
never beyond the midpoint of the shaft projection, to provided they are properly installed, maintained and
avoid undue bearing load and shaft deflection. Never operated within the limits of speed, torque or other load
overtighten belts or chains. Careful and accurate conditions under which they were sold. Sumitomo
installation is essential for best results and for trouble- further states that Hyponic® Speed Reducers are
free operation. Before installing, the shafts should be warranted to be free from defects in material or
checked to make sure that they are parallel and level. workmanship for a period of two years from the date of
Perfect alignment after mounting can be checked with a shipment. Sumitomo assumes no liability beyond
string or straight edge held against the sides of the product repair or replacement under this limited
sprocket or pulley base. warranty.
Couplings should be properly aligned to the limits For construction purposes, be sure to obtain
specified by the manufacturer. On coupled speed certified dimension sheets or drawings. Although we
reducers coupling alignment should be checked prior to take every precaution to include accurate data in our
initial startup. catalog, we cannot guarantee such accuracy. If
performance guarantees are required, they should be
Shaft Rotation obtained in writing from the factory. Full consideration
The direction of shaft rotation on Hyponic® will be given to such requests when complete details
speed reducers varies according to frame size and ratio. are given of the proposed installation.
Please refer to the Technical Information section for Installation
specific data on the shaft rotation for various models.
Be sure to install and operate Hyponic® speed
Input Speeds reducers in compliance with applicable local and
In general terms, the standard input speeds of national safety codes. Appropriate guards for rotating
single reduction units are 1750 and 1165 RPM. shafts should be used and are available from local
stocks.
When non-standard input speeds are used, the
horsepower and torque ratings will also vary. Dimensions
Thermal Capacity All dimensions in this catalog are for reference

purposes only. Consult factory for certified dimensions.
The Hyponic® speed reducers smooth, almost
frictionless operation all but eliminates the conventional
limitations due to heat. In all sizes, Hyponic® speed
reducers have thermal ratings that exceed their
mechanical capacity.
Hyponic
5
Notes
Hyponic
6
Gearmotors
Gearmotors
A
Hollow Shaft Type
Hyponic
A-1
Gearmotors
Product Range
Table A-1 Hollow Shaft Type
Nominal Ratio (:1) 5 7 10 12 15 20 25 30 40 50 60
Output RPM (1750 RPM Input) 350 250 175 146 117 87.5 70 58.3 43.8 35 29.2
Frame Size: 1120, Bore: Ø0.75²
1/8 HP [1]
Frame Size: 1120, Bore Ø0.75² Frame Size: 1220, Bore: Ø1.00 ²
Frame Size: 1120, Bore: Ø0.75² Frame Size: 1220, Bore: Ø1.00 ²
1/4 HP [1]
1/3 HP Frame Size: 1220, Bore: Ø1.00² Frame Size: 1320, Bore: Ø1.25 ²
1/2 HP [1]
3-Phase Frame Size: 1320, Bore: Ø1.25² Frame Size: 1420, Bore: Ø1.375 ²
1 HP [1]
1-1/2 HP Frame Size: 1420, Bore Ø1.375² Frame Size: 1520, Bore: Ø1.50 ²
Gearmotors
2 HP [1] Frame Size: 1420, Bore: Ø1.375² Frame Size: 1520, Bore: Ø1.50 ²
Product
Range
3 HP Frame Size: 1520, Bore: Ø1.50² Frame Size: 1531, Bore: Ø1.50 ²
5 HP Frame Size 63, Bore: Ø2.00²

7-1/2 HP Frame Size 63, Bore: Ø2.00²
Single-Phase 1/4 HP Frame Size: 1220, Bore: Ø1.00² Frame Size: 1320, Bore: Ø1.25 ²
Inverter Duty
1 HP Frame Size: 1420, Bore: Ø1.375² Frame Size: 1520, Bore; Ø1.50 ²
2 HP Frame Size: 1520, Bore; Ø1.50² Frame Size: 1531, Bore Ø1.50 ²
3 HP Frame Size: 63, Bore: Ø2.00²
5 HP Frame Size: 64, Bore: Ø2.00²
Notes: [1] Those selections shaded in blue offer an increased service factor. Please refer to the gearmotor selection tables forspecific unit service
factor details.
[2] These reduction ratios are not available from stock; consult factory for availability.
[3] This frame size is torque limited. Overload may occur if the motor is loaded to its full capacity. Sumitomo recommends theuse of a
torque limiting device to protect the unit and/or the driven machine.
Hyponic
A-2
Gearmotors
80 100 120 150 200 240 300[2] 360[2] 480[2] 560[2] 750[2] 900[2] 1200[2] 1440[2]
21.9 17.5 14.6 11.7 8.75 7.29 5.83 4.86 3.65 3.13 2.33 1.94 1.46 1.222
Frame Size: 1230, Bore: Ø1.00² [3]

Frame Size: 1430, Bore: Ø1.375² Frame Size: 56, Bore: Ø1.50² [3]

Frame Size: 56,
Bore: Ø1.50² [3]
Frame Size: 1531,

Bore: Ø1.50²
Frame Size: Frame Size: 60,
1531, Bore:
Ø1.50² Bore: Ø2.00²
Gearmotors
Frame Size: 1531,
Bore: Ø1.50² Frame Size: 60,
Bore: Ø2.00²
Product
Range
Frame Size: 60, Bore: Ø2.00 ²

Frame Size: Frame Size: 60,
1531, Bore:
Ø1.50² Bore: Ø2.00²
Hyponic
A-3
Gearmotors
Standard Specifications
Table A-2
Item Standard Specification Standard Specification with Built-In Brake
Capacity 1/8 HP - 7.5 HP, 4-pole
1/8 HP - 7.5 HP, 4-pole
Range FB Brake
Totally Enclosed Fan Cooled Totally Enclosed Fan Cooled
Enclosure
(1/8 HP Totally Enclosed Non Ventilated) (1/8 HP Totally Enclosed Non Ventilated)
3-Phase Power 230/460V, 60 Hz 230/460V, 60 Hz
Supply 575V, 60 Hz 575V, 60 Hz
1/8 HP - 1/2 HP: Class E 1/8 HP - 1/2 HP: Class E, Brake: Class B
Insulation
3/4 HP - 7.5 HP: Class B 3/4 HP - 7.5 HP: Class B, Brake: Class B
Time Rating Continuous Continuous
Capacity
1/8 HP - 1/2 HP, 4-pole 1/8 HP - 1/2 HP, 4-pole
Range
Enclosure Totally Enclosed Fan Cooled Totally Enclosed Fan Cooled
Motor Power
Single-Phase 115/230V, 60 Hz 115/230V, 60 Hz
Supply
Insulation Class B Class B, Brake: Class B
Gearmotors
Time Rating Continuous Continuous
Specifications
Starting
Standard
Capacitor-Starting, Capacitor-Run Capacitor-Starting, Capacitor-Run

Method
Capacity 1/8 HP - 5 HP, 4-pole
1/8 HP - 5 HP, 4-pole
Range FB Brake
Enclosure Totally Enclosed Fan Cooled Totally Enclosed Fan Cooled
Invertor Duty Power
230/460V, 60 Hz 230/460V, 60 Hz
Supply
Insulation Class B Class B, Brake: Class B
Time Rating Continuous (6-60 Hz Constant Torque) Continuous (6-60 Hz Constant Torque)
Lubrication Grease Lubricated. Filled with special high-grade grease prior to shipment from factory.
Reducer Reduction Combination of Hypoid gear and Involute gear.
Material Casing: Aluminum Alloy, Gear: Chrome-Molybdenum steel
Installation Indoor (free from water)
Temperature 14 to 104°F
Ambient Conditions Humidity 85% maximum - no condensation
Altitude 3280 feet
Atmosphere Free from corrosive gas, explosive gas, or steam. Area to be well ventilated.
Installation Angle No Limitation
Mounting Direction of Terminal Box

Mounting direction of terminal box may be changed in 90 increments. A mounting direction other than standard must be changed
by the factory and specified when an order is placed. Refer to Fig. A-1 for mounting direction and lead wire opening direction.The
direction cannot be changed after shipment.
Fig. A-1 3-phase (Standard motors and motors for inverters)
Up
Left Right
Standard
The directions indicated in Fig. A-1 are viewed from opposite side of fan cover.
Arrow indicates lead wire opening direction Please consult factory for brakemotor, plug-in shaft, bolt-on flange and bolt-on feet models.
Hyponic
A-4
Gearmotors
Gearmotor Selection Flowchart
DETERMINE TYPE OF DRIVEN MACHINE
CHECK HOURS OF OPERATION
CHOOSE A LOAD CLASSIFICATION See Load Classification Tables, Pages A-7~8
SPECIFY MOTOR HORSEPOWER & SPEED See Gearmotor Selection Tables, Pages A-10~21
Gearmotors
DETERMINE INPUT AND OUTPUT SPEEDS
Flowchart
Selection
MAKE A PRELIMINARY SELECTION
DIRECT
NO
CONNECT DETERMINE OVERHUNG LOAD
OUTPUT
OHL<
YES YES
OHL IN
TABLES
SELECT MOUNTING STYLE
NO
CHECK OPERATING ENVIRONMENT
LARGER UNIT OR DECREASE OHL
FINALIZE REQUIRED OPTIONS See Standard Specifications, Page A-4
Hyponic
A-5
Gearmotors
Gearmotor Selection Procedure

The following information is required to properly select a Hyponic® Gearmotor:
1. Application Type of Driven Machine Example: Belt Conveyor Uniformly Fed

2. Hours of Operation per Day 8 Hours of Operation per Day
3. Motor Power and Speed 3 HP Motor, 1750 RPM
4. Desired Output Speed 120 RPM
5. Mounting Position and Style Horizontal Shaft Mounted
6. Environmental Conditions Inside Industrial Plant
7. Required Options Motor Brake
8. Electrical Specifications 460 Volts, 60 Hertz, 3 phase
9. Overhung or Thrust Loads None Hollow Shaft Output
10. Shaft Dimensions Inch or Metric 1-1/2Head Shaft
Review the Basic Information and Recommendations on page 4, then proceed to Selection Example 1.
Selection Example 1
Step 1
Gearmotors Using the information above, choose a Load Classification from the AGMA Load Classification Tables (pages A-7~8).
Table A-4 identifies service classes based on applications and hours of operation. For Conveyors Uniformly Loaded
Procedure
Selection
or Fed, Belt, Up to 10 hours per day, the recommended minimum is Class I.
Step 2
Go to the Gearmotor Selection Tables (pages A-10~21) for the correct input power and find the ratio providing the
output speed closest to the desired output speed. The closest speed to 120 RPM is 117 RPM. Match the Class to the
minimum obtained in Step 1 and make a selection. The selection is 3-1520Y-15.
Step 3
Are there any overhung or thrust loads present? If not, then proceed to Step 4. Otherwise, any overhung or thrust
loads must be checked against the capability of the selection.
To check overhung load use this formula: HP: Transmitted or Motor HP

Cf: Load Connection Factor
Overhung = 126,000 x HP x Cf x Lf x Fs Lf: Load Location Factor
Load (OHL) DxN D: Pitch Diameter (in)
N: Shaft RPM
Fs: Shock factor
The specific values for the overhung load factors, as well as a method to evaluate thrust loads, are listed on page D-5
contained in the Technical Information Section.
Step 4
Go to page 2. Select the desired mounting position and housing style from the nomenclature pages. The horizontal,
shaft mounted Hyponic Gearmotor designation is RNYM. The unit nomenclature for a shaft-mounted unit is RNYM3-
1520YA-15.
Step 5
Check environmental conditions against the Standard Specifications on page A-4. Since this application is located
inside an industrial plant, no environmental modifications are required.
Step 6
Specify desired options: 460V motor, 460-volt brake, 1-1/2 hollow bore, and a torque arm.
Hyponic
A-6
Gearmotors
AGMA Load Classifications

Class I For steady loads not exceeding normal motor rating, 8 to 10 hours a
day. Moderate shock loads where service is intermittent
(AGMA equivalent Service Factor: 1.0).
Class II For steady loads not exceeding normal motor rating and 24 hours a
day service. Moderate shock loads for 8 hours a day
(AGMA equivalent Service Factor: 1.4).
Class III For moderate shock loads for 24 hours a day. Heavy shock loads for
8 hours a day (AGMA equivalent Service Factor: 2.0). [1]
Table A-3 Load Classification Listed By Industry [2]
Class Class Class Class

Up to 24 Up to 24 Up to 24 Up to 24
Application 10 Hr. Hr. Application 10 Hr. Hr. Application 10 Hr. Hr. Application 10 Hr. Hr.
per per per per per per per per
day day day day day day day day
Brewing & Distilling Lumber Industry Oil Well Pumping Refer to Factory Tire Building Machines Refer to Factory
Bottling Machinery I II Barkers Paraffin Filter Press II II Tire, Tube Press Gearmotors
Brew Kettles, Cont. Spindle Feed II III Rotary Kilns II II Openers Refer to Factory
Duty II Barkers Tubers & Stainers II II
Classifications
Can Filling Machines I II Main Drive III III Paper Mills
AGMA
CookersCont. Duty II Carriage Drive Refer to Factory Agitators (Mixers) II II Sewage Disposal
Load
Mash TubsCont. Duty II Conveyors BarkerAuxiliaries Aerators Refer to Factory
Scale Hoppers Burner II III Hyd. III Bar Screens I II
Frequent Starts II II Main or Heavy Duty II III Barker, Mechanical III Chemical Feeders I II
Main Log III III Barking Drum III Collectors I II
Re-Saw Beater & Pulper II Dewatering Screens II II
Clay Working Industry Bleacher II
Brick Press III III Merry-Go-Round II III Grit Collectors I II
Slab III III Calenders II Scum Breakers II II
Briquette Machines III III CalendersSuper II
Clay Working Transfer II III Slow or Rapid Mixers II II
ChainsFloor II III Converting Mach. Sludge Collectors I II
Machinery II II Except Cutters
Pug Mills II II ChainsGreen II III Thickeners II II
Cut-Off SawsChain II III Platers II Vacuum Filters II II
Cut-Off SawsDrag II III Conveyors II
Distilling (See Brewing) Debarking Drums III III Couch II Textile Industry
FeedsEdger II III Cutters, Platers III Batchers II II
Cylinders _ II
Dredges FeedsGang III III Calenders II II
FeedsTrimmer II III Dryers II Card Machines II II
Cable Reels II
Log Deck III III Felt Stretchers II Cloth Finishing Machines
Conveyors II II
Log HaulsIncline, Felt Whippers III (Calenders, Dryers,
Cutter Head Drives III III
Well Type III III Jordans II Pads, Tenters,
Jig Drives III III
Log Turning Devices III III Log Haul III Washers) II II
Maneuvering Winches II
Planer Feed II III Presses II Dry Cans II II
Pumps II II
Planer Tilting Hoists II III Pulp Machine Reels II Dyeing Machinery II II
Screen Drives III III
RollsLiveOff Stock Chests II Knitting Machinery
Stackers II II Refer to Factory
BearingRoll Cases III III Suction Rolls II Looms, Mangles,
Utility Winches II
Sorting Table II III Washers & Nappers II II
Tipple Hoist II III Thickeners II Range Drives Refer to Factory
Food Industry Winders II
TransfersChain II III Soapers, Spinners II II
Beet Slicers II II
TransfersCraneway II III Rubber Industry Tenter Frames II II
Bottlings, Can
Tray Drives II III Mixer III III Winders II II
Filling Mach. I II
Rubber Calender II II Yarn Preparatory
Cereal Cookers I II
Rubber Mill Machinery (Cards,
Dough Mixers II II
Oil Industry (2 or more) II II Spinners,
Meat Grinders II II
Chillers II II Sheeter II II Slashers) II II
Notes: [1] For applications involving frequent start-stop, braking or reversing, or quick starting of a large inertia load, cons
ult the factory for model
selection on recommended modifications.
[2] Load classification listed by application shown on next page.
Hyponic
A-7
Gearmotors

Table A-4 Load Classification Listed By Application
Class Class Class Class

Up to 24 Up to 24 Up to 24 Up to 24
Application 10 Hr. Hr. Application 10 Hr. Hr. Application 10 Hr. Hr. Application 10 Hr. Hr.
per per per per per per per per
day day day day day day day day
Agitators Jig Drives III III Tray Drives II III Pullers
Pure Liquids I II Maneuvering Winches II Veneer Lathe Drives Refer to Factory Barge Haul III III
Liquids and Solids II II Pumps II II
Liquids Variable Screen Drive III III Machine Tools Pumps
Density II II Stackers II II Bending Roll II II Centrifugal I II
Semi-liquids Utility Winches II Notching Press Proportioning II II
Variable Density II II Belt Driven Refer to Factory Reciprocating
Elevators Plate Planer III III Single Acting
Blowers Bucket Uniform Load I II Punch Press 3 or more Cylinders II II
Centrifugal I II Bucket Heavy Load II II Gear Driven III III Double Acting
Lobe II II Bucket Continous I II Tapping Machines III III
Vane I II Centrifugal Discharge I II 2 or more Cylinders II II
Other Machine Tools Single Acting
Escalators I II Main Drives II II
Brewing and Distilling Freight I II 1 or 2 Cylinders Refer to Factory
Auxiliary Drives I II Double Acting
Bottling Machinery I II Gravity Discharge I II
Brew Kettles Man Lifts Refer to Factory Single Cylinder Refer to Factory
Continuous Duty II Passenger Metal Mills Rotary Gear Type I II
Cookers Continuous Service Hand Lift III Bridle Roll Drives III III Lobe, Vane I II
Duty II Draw Bench Carriage III III
Mash Tubs Fans Draw Bench Rubber Industry
Continuous Duty II Centrifugal II II Main Drive III III Mixer III III
Scale Hopper Cooling Towers Forming Machines III III Rubber Calender II II
Gearmotors Frequent Starts II II Induced Draft II II Pinch Dryer & Scrubber Rubber Mill (2 or more) II II
Forced Draft Refer to Factory Rolls, Reversing Refer to Factory Sheeter II II
Can Filling Machines I II Induced Draft II II Slitters II II
Classifications
Tire Building Machines Refer to Factory

Large (Mine, etc.) II II Table Conveyors
Non-Reversing II III Tire & Tube Press Refer to Factory
Cane Knives II II Large Industrial II II
AGMA
Reversing III Openers

Load
Light (Small Diameter) I II Tubers & Strainers II II

Car Dumpers III Winding Reels Strip III
Feeders Wire Drawing &
Flattening Machine II III Sewage Disposal
Car Pullers Apron II II
Intermittent Duty I Belt II II Wire Winding Machine II II Equipment
Disc I II Aerators Refer to Factory
Clarifiers I II Reciprocating III III Bar Screens I II
Mills, Rotary Type Chemical Feeders I II
Screw II II Ball III III
Classifiers II II Collectors, Circuline
Clay Working Cement Kilns
Food Industry Dryers & Coolers II II or Straightline I II
Machinery Beet Slicer II II Dewatering Screens II II
Brick Press III III Kilns II II
Cereal Cooker I II Pebble III III Grit Collectors I II
Briquette Machine III III Dough Mixer II II Scum Breakers II II
Clay Working Rod III III
Meat Grinders II II Tumbling Barrels III III Slow or Rapid Mixers II II
Machinery II II Sludge Collectors I II
Pug Mill II II Generators Thickeners II II
(Not Welding) I II Mixers Vacuum Filters II II
Compressors Concrete Mixers,
Centrifugal I II Continuous II II
Lobe II II Hammer Mills III III Screens
Concrete Mixers,
Reciprocating Intermittent I Air Washing I II
Multi-Cylinder II II Laundry Washers Rotary Stone
Reversing II II Constant Density I II
Single Cylinder III III Variable Density II II or Gravel II II
Conveyors Uniformly Traveling Water
Laundry Tumblers II II
Loaded or Fed Intake I II
Oil Industry
Apron I II Line Shafts Chillers II II
Assembly I II Heavy Shock Load III III Slab Pushers II II
Oil Well Pumping Refer to Factory Steering Gear II II
Belt I II Moderate Paraffin Filter Press II II
Bucket I II Shock Load II II Rotary Kilns II II Stokers I II
Chain I II Uniform Load I II
Flight I II Textile Industry
Oven I II Lumber Industry
Barkers Spindle Feed Paper Mills Batchers II II
Screw I II Refer to Factory Aerators Refer to Factory
Barkers Main Drive Refer to Factory Calenders II II
Conveyors Heavy Duty Carriage Drive Agitators (Mixers) II II Card Machines II II
Refer to Factory Barker Auxiliaries,
Not Uniformly Fed Conveyors Burner II III Cloth Finishing Machines
Apron II II Conveyors Main or Hydraulic III (Washers, Pads,
Assembly II II Heavy Duty II III Barker, Mechanical III Tenters)
Belt II II Conveyors Main Log III III Barking Drum III (Dryers,
Bucket II II Conveyors Beater & Pulper II Calenders, etc.) II II
Chain II II Merry-Go-Round II III Bleacher II Dry Cans II II
Flight II II Conveyors Slab III III Calenders II Dryers II II
Live Roll (Package) I II Conveyors Transfer II III Calenders Super II
Converting Machines, Dyeing Machinery II II
Oven II II Conveyors Waste II II Knitting Machines
Reciprocating III III Chains Floor II III except Cutters,
Platers II (Looms, etc.) Refer to Factory
Screw II II Chains Green II III Looms II II
Shaker III III Cut-Off Saws Chain II III Conveyors II
Conveyors, Log III Mangles II II
Cranes and Hoists Cut-Off Saws Drag II III Nappers II II
Debarking Drums III III Couch II
Main Hoists III III Cutters, Platers III Pads II II
Heavy Duty III III Feeds Edger II III Range Drives Refer to Factory
Feeds Gang III III Cylinders II
Medium Duty II II Dryers II Slashers II II
Reversing II II Feeds Trimmer II III
Log Deck III III Felt Stretcher II Soapers II II
Skip Hoists II II Felt Whipper III Spinners II II
Trolley Drive II II Log Hauls Incline
Well Type III III Jordans II Teneter Frames II II
Bridge Drive II II Presses II Washers II II
Log Turning Devices III III
Planer Feed II III Pulp Machines, Reel II Winders (Other
Crushers Stock Chests II
Ore III III Planer Tilting Hoists II III than Batchers) II II
Rolls Live Off Brg. Suction Roll II Yarn Preparatory
Stone III III Washers and
Roll Cases III III Machines (Cards,
Dredges Sorting Table II III Thickeners II Spinners, Slashers,
Cable Reels II Tipple Hoist II III Winders II etc.) II II
Conveyors II II Transfers Chain II III
Cutter Head Drives III III Transfers Craneway II III Printing Presses I II Windlass II II
Hyponic
A-8
Gearmotors
Motor Thermal Ratings

Table A-5 Motor Thermal Rating (C x Z)[1]
Motor Power Allowable C x Z Motor Moment of Inertia(lb-in2)
HP (kW) (35%ED) [2] 35% - 50% ED[2] 50% - 80% ED[2] 80% - 100% ED[2] Standard With Brake
1/8 (0.1) 3200 3000 2000 1200 1.13 1.20
1/4 (0.2) 2200 2800 2800 2500 1.71 1.88
1/3 (0.25) 2200 2800 2800 2500 1.71 1.88
1/2 (0.4) 1800 2200 1500 1500 2.22 2.33
3/4 (0.55) 1800 2200 1500 1500 3.45 3.80
1 (0.75) 1400 1400 800 500 4.10 4.45
1.5 (1.1) 1400 1400 800 500 6.33 7.11
2 (1.5) 1200 1200 500 400 7.28 8.04
3 (2.2) 1000 900 400 200 11.4 12.8
5 (3.7) 800 800 800 700 29.0 32.8
7.5 (5.5) 300 300 200 150 39.1 42.9
Gearmotors
The calculated C x Z value (steps 1 - 3 outlined below) should be less than the allowable value listed in Table A-5.
Thermal
(1) Obtain the C value.
Ratings
Motor
I M + IL IM =
Moment of inertia of motor.
C=
IM IL =
Total moment of inertia of load as seen from the motor.
(2) Obtain the Z value (number of starts per hour).
(a) Assume that one operating period consists ofon time ta (sec), off time tb (sec) and the motor is started nr
(times/cycle).
3600nr
Zr = (times/hr)
ta + tb
(b) When inching, ni (times/cycle) is included in 1 cycle (ta+tb), the number of inching times per hour, Zi,
is then included in the number of starts.
3600ni
Zr = (times/hr)
ta + tb
(c) Calculate Z by adding Zr to Zi.
3600 1
Z = Zr + 1 Zi = (nr+ ni) (times/hr)
2 ta + tb 2
(3) Calculate C multiplied by Z.
Use the value of C obtained in step (1) and Z from step (2).
(4) Obtain the duty cycle %ED and check with Table A-5.
ta
%ED = x 100 ta = on-time
ta +tb tb = off-time
Notes: [1] Please consult the factory for inverter duty and single-phase motors.
[2] %ED = Duty Cycle
Hyponic
A-9
Gearmotors
Selection Tables 60 Hz, 3-Phase, 1750 RPM

1/8 HP (0.1 kW)
Output Output Service Factor Hollow Bore Selection
Dimension
Speed Torque AGMA Overhung Load [2] HP Frame Nominal
SF Symbol Size Ratio Page
RPM inlbs Class[1] lbs
350 11
19.1 2.14 III 130 01 1120YC 5
250 29
26.8 2.14 III 140 01 1120YC 7
175 41
38.3 2.14 III 165 01 1120YC 10
146 49
45.9 2.14 III 175 01 1120YC 12
117 62
57.2 2.14 III 185 01 1120YC 15
87.5 82
76.5 2.14 III 210 01 1120YC 20
70.0 103
95.7 2.14 III 220 01 1120YC 25 A-22
58.3 123
115 2.14 III 230 01 1120YC 30
1.07 I 250 01 1120YA 40
43.8 165
153
2.14 III 350 01 1220YC 40
1.07 I 275 01 1120YA 50

35.0 205
191
2.14 III 375 01 1220YC 50
Gearmotors
1.07 I 285 01 1120YA 60
29.2 247
229
2.14 III 385 01 1220YC 60
Selection
Tables
1.07 I 395 01 1230YA 80

21.9 329
306
2.14 III 660 01 1330YC 80
1.07 I 395 01 1230YA 100

17.5 411
383
2.14 III 680 01 1330YC 100
1.07 I 405 01 1230YA 120

14.6 493
459
2.14 III 695 01 1330YC 120
A-23
1.07 I 405 01 1230YA 150
11.7 617
572
2.14 III 695 01 1330YC 150
1.07 I 405 01 1230YA 200

8.75 822
765
2.14 III 695 01 1330YC 200
868
868 0.94 * 405 01 1230Y 240
7.29
982
919 1.88 II 695 01 1330YB 240
5.83 1159
1149 1.00 I 695 01 361YA 300
4.86 1390
1378 1.00 I 695 01 361YA 360
3.65 1726
1726 0.94 * 695 01 361Y 480
3.13 1726
1726 0.81 * 695 01 361Y 560
A-25
2.33 1726
1726 0.60 * 695 01 361Y 750
1.94 1726
1726 0.50 * 695 01 361Y 900
1.46 1726
1726 0.38 * 695 01 361Y 1200
1.22 1726
1726 0.31 * 695 01 361Y 1440
Notes: [1] AGMA Class values replaced by * are torque limited. Overload may occur if the motor is loaded to its full capacity. Sumitomo
recommends the use of a torque-limiting device to protect the unit and/or the driven machine.
[2] Overhung Load values are based at a distance of 0.78 inch from the collar.
Hyponic
A-10
Gearmotors
Selection Tables 60 Hz, 3-Phase, 1750 RPM, cont.
1/4 HP (0.2 kW)

Dimension
1.07 I 130 02 1120YA 5
350 41
38.3
2.14 III 185 02 1220YC 5
1.07 I 140 02 1120YA 7

250 58
53.6
2.14 III 210 02 1220YC 7
1.07 I 165 02 1120YA 10

175 82
76.5
2.14 III 230 02 1220YC 10
1.07 I 175 02 1120YA 12
146 98
91.7
2.14 III 240 02 1220YC 12
1.07 I 185 02 1120YA 15

117 114
123
2.14 III 265 02 1220YC 15
1.07 I 210 02 1120YA 20

87.5 153
165 A-22
2.14 III 295 02 1220YC 20 Gearmotors
1.07 I 220 02 1120YA 25

70.0 191
205
Selection
2.14 III 305 02 1220YC 25
Tables
1.07 I 230 02 1120YA 30
58.3 230
247
2.14 III 330 02 1220YC 30
1.07 I 350 02 1220YA 40
43.8 306
329
2.16 III 570 02 1320YC 40
1.07 I 375 02 1220YA 50
35.0 383
411
2.16 III 615 02 1320YC 50
1.07 I 385 02 1220YA 60

29.2 459
493
2.16 III 635 02 1320YC 60
1.07 I 660 02 1330YA 80
21.9 612
658
2.14 III 960 02 1430YC 80
1.07 I 680 02 1330YA 100
17.5 765
822
2.14 III 980 02 1430YC 100
1.07 I 695 02 1330YA 120

14.6 917
982 A-23
2.14 III 980 02 1430YC 120
1.07 I 695 02 1330YA 150
11.7 1145
1230
2.14 III 980 02 1430YC 150
1.07 I 695 02 1330YA 200
8.75 1531
1646
2.14 III 980 02 1430YC 200
1726
1726 0.94 * 695 02 1330Y 240
7.29
1837
1974 1.88 II 980 02 1430YB 240
5.83 2297
2319 1.00 I 980 02 461YA 300
4.86 2756
2788 1.00 I 980 02 461YA 360
3.65 3452
3452 0.94 * 980 02 461Y 480
3.13 3452
3452 0.81 * 980 02 461Y 560
A-25
2.33 3452
3452 0.60 * 980 02 461Y 750
1.94 3452
3452 0.50 * 980 02 461Y 900
1.46 3452
3452 0.38 * 980 02 461Y 1200
1.22 3452
3452 0.31 * 980 02 461Y 1440
Hyponic
A-11
Gearmotors

1/3 HP (0.25 kW)
Speed Torque Dimension
AGMA Overhung Load [2] HP Frame Nominal
350 51.0 1.60 II 185 03 1220YB 5

250 71.4 1.60 II 210 03 1220YB 7
175 102 1.60 II 230 03 1220YB 10
146 122 1.60 II 240 03 1220YB 12
117 153 1.60 II 265 03 1220YB 15
A-22
87.5 204 1.60 II 295 03 1220YB 20
70.0 255 1.60 II 305 03 1220YB 25
58.3 306 1.60 II 330 03 1220YB 30
43.8 408 1.62 II 570 03 1320YB 40
35.0 510 1.62 II 615 03 1320YB 50
29.2 612 1.62 II 635 03 1320YB 60
21.9 815 1.60 II 960 03 1430YB 80

17.5 1020 1.60 II 980 03 1430YB 100
14.6 1223 1.60 II 980 03 1430YB 120
Gearmotors A-23
11.7 1526 1.60 II 980 03 1430YB 150
8.75 2041 1.60 II 980 03 1430YB 200
Selection
7.29 2450 1.40 II 980 03 1430YB 240

Tables
5.83 2903 1.60 II 1400 03 56YB 300

4.86 3479 1.54 I 1400 03 56YA 360
3.65 4647 1.16 I 1400 03 56YA 480
A-26
3.13 5417 1.19 I 1400 03 56YA 560
2.33 6479 0.85 * 1400 03 56Y 750
1.94 6479 0.70 * 1400 03 56Y 900
1.46 6479 0.53 * 1400 03 56Y 1200
1.22 6479 0.44 * 1400 03 56Y 1440
1/2 HP (0.4 kW)

Dimension
1.07 I 185 05 1220YA 5
350 76.5
2.14 III 305 05 1320YC 5
1.07 I 210 05 1220YA 7
250 107
2.14 III 350 05 1320YC 7
1.07 I 230 05 1220YA 10

175 153
2.14 III 385 05 1320YC 10
1.07 I 240 05 1220YA 12
146 183
2.14 III 405 05 1320YC 12
1.07 I 265 05 1220YA 15
117 229 A-22
2.14 III 440 05 1320YC 15
1.07 I 295 05 1220YA 20

87.5 306
2.14 III 485 05 1320YC 20
1.07 I 305 05 1220YA 25

70.0 383
2.14 III 505 05 1320YC 25
1.07 I 330 05 1220YA 30
58.3 459
2.14 III 525 05 1320YC 30
Hyponic
A-12
Gearmotors
1/2 HP (0.4 kW) cont.

Dimension
1.08 I 570 05 1320YA 40
43.8 612
2.14 III 855 05 1420YC 40
1.08 I 615 05 1320YA 50 A-22

35.0 765
2.14 III 900 05 1420YC 50
1.08 I 635 05 1320YA 60

29.2 917
2.14 III 935 05 1420YC 60
1.07 I 960 05 1430YA 80

21.9 1223
2.14 III 1375 05 1530YC 80
1.07 I 980 05 1430YA 100

17.5 1531
2.14 III 1400 05 1530YC 100
1.07 I 980 05 1430YA 120
14.6 1835
2.14 III 1400 05 1530YC 120 Gearmotors
A-23
1.07 I 980 05 1430YA 150
Selection
11.7 2289
Tables
2.14 III 1400 05 1530YC 150
1.07 I 980 05 1430YA 200

8.75 3061
1.53 II 1400 05 1530YB 200
3452 0.94 * 980 05 1430Y 240
7.29
3674 1.76 II 1400 05 1530YB 240
5.83 4594 1.00 I 1400 05 56YA 300
4.86 5567 1.01 I 1400 05 56YA 360
3.65 6479 0.88 * 1400 05 56Y 480
3.13 6479 0.76 * 1400 05 56Y 560
A-26
2.33 6479 0.56 * 1400 05 56Y 750
1.94 6479 0.47 * 1400 05 56Y 900
1.46 6479 0.35 * 1400 05 56Y 1200
1.22 6479 0.30 * 1400 05 56Y 1440
Hyponic
A-13
Gearmotors
3/4 HP (0.55 kW)

Dimension
350 115 1.43 II 305 08 1320YB 5
250 161 1.43 II 350 08 1320YB 7
175 230 1.43 II 385 08 1320YB 10
146 275 1.43 II 405 08 1320YB 12
A-22
117 343 1.43 II 440 08 1320YB 15
87.5 459 1.43 II 485 08 1320YB 20
70 574 1.43 II 505 08 1320YB 25
58.3 689 1.43 II 525 08 1320YB 30
43.8 917 1.43 II 855 08 1420YB 40 A-22

35 1148 1.43 II 900 08 1420YB 50 A-22
29.2 1376 1.43 II 935 08 1420YB 60 A-22
Gearmotors
21.9 1835 1.43 II 1375 08 1530YB 80 A-23
Selection
17.5 2296 1.43 II 1400 08 1530YB 100

Tables
14.6 2752 1.43 II 1400 08 1530YB 120

A-23
11.7 3434 1.43 II 1400 08 1530YB 150
8.75 4592 1.41 II 1400 08 1530YB 200
7.29 5511 1.17 I 1400 08 1530YA 240 A-23
5.83 6381 0.93 * 1400 08 56Y 300 A-26
4.86 6479 0.78 * 1400 08 56Y 360 A-26
3.65 6479 0.59 * 1400 08 56Y 480 A-26
1 HP (0.75 kW)
Dimension
1.07 I 305 1 1320YA 5
350 153
2.07 III 460 1 1420YC 5
1.07 I 350 1 1320YA 7

250 214
2.07 III 515 1 1420YC 7
1.07 I 385 1 1320YA 10
175 306
2.07 III 580 1 1420YC 10
1.07 I 405 1 1320YA 12

146 367 A-22
2.07 III 615 1 1420YC 12
1.07 I 440 1 1320YA 15
117 458
2.07 III 660 1 1420YC 15
1.07 I 485 1 1320YA 20
87.5 612
2.07 III 715 1 1420YC 20
1.07 I 505 1 1320YA 25

70.0 765
2.07 III 760 1 1420YC 25
Hyponic
A-14
Gearmotors
1 HP (0.75 kW) cont.

Dimension
1.07 I 525 1 1320YA 30
58.3 919
2.07 III 805 1 1420YC 30
1.07 I 855 1 1420YA 40

43.8 1223
2.07 III 1245 1 1520YC 40
A-22
1.07 I 900 1 1420YA 50
35.0 1531
2.07 III 1310 1 1520YC 50
1.07 I 935 1 1420YA 60

29.2 1835
2.07 III 1355 1 1520YC 60
1.07 I 1375 1 1530YA 80

21.9 2446
2.07 III 1375 1 1531YC 80
Gearmotors
17.5 3061 1.07 I 1400 1 1530YA 100
A-23
14.6 3669 1.07 I 1400 1 1530YA 120
Selection
Tables
11.7 4579 1.07 I 1400 1 1530YA 150
8.75 6122 1.06 I 1400 1 1530YA 200
7.29 7349 0.88 * 1400 1 1530Y 240 A-23

5.83 6479 0.71 * 1400 1 56Y 300 A-26
4.86 6479 0.59 * 1400 1 56Y 360 A-26
3.65 6479 0.44 * 1400 1 56Y 480 A-26
1.5 HP (1.1 kW)

Dimension
350 230 1.38 I 460 1H 1420YA 5
250 321 1.38 I 515 1H 1420YA 7
175 459 1.38 I 580 1H 1420YA 10
146 550 1.38 I 615 1H 1420YA 12

117 687 1.38 I 660 1H 1420YA 15 A-22
87.5 918 1.38 I 715 1H 1420YA 20
70.0 1148 1.38 I 760 1H 1420YA 25

58.3 1378 1.38 I 805 1H 1420YA 30
43.8 1835 1.38 I 1245 1H 1520YA 40
35.0 2296 1.38 I 1310 1H 1520YA 50 A-22
29.2 2752 1.38 I 1355 1H 1520YA 60 A-22
21.9 3669 1.38 I 1375 1H 1531YA 80 A-23
17.5 4592 2.00 III 2205 1H 60YC 100
A-24
14.6 5504 2.00 III 2205 1H 60YC 120
Hyponic
A-15
Gearmotors
2 HP (1.5 kW)
Dimension
RPM inlbs Class lbs
1.04 I 460 2 1420YA 5
350 306
1.48 II 660 2 1520YB 5
1.04 I 515 2 1420YA 7
250 429
1.48 II 745 2 1520YB 7
1.04 I 580 2 1420YA 10
175 612
1.48 II 835 2 1520YB 10
1.04 I 615 2 1420YA 12
146 734 A-22
1.48 II 890 2 1520YB 12
1.04 I 660 2 1420YA 15
117 916
1.48 II 945 2 1520YB 15
1.04 I 715 2 1420YA 20
87.5 1224
1.48 II 1035 2 1520YB 20
Gearmotors 1.04 I 760 2 1420YA 25
70.0 1531
1.48 II 1100 2 1520YB 25
Selection
1.04 I 805 2 1420YA 30

Tables
58.3 1838
1.48 II 1155 2 1520YB 30
1.04 I 1245 2 1520YA 40 A-22
43.8 2446
1.48 II 1245 2 1531YB 40 A-23
1.04 I 1310 2 1520YA 50 A-22
35.0 3061
1.48 II 1310 2 1531YB 50 A-23
1.04 I 1355 2 1520YA 60 A-22
29.2 3669
1.48 II 1355 2 1531YB 60 A-23
1.04 I 1375 2 1531YA 80 A-23
21.9 4892
1.47 II 2170 2 60YB 80 A-24
17.5 6122 1.47 II 2205 2 60YB 100 A-24
14.6 7339 1.47 II 2205 2 60YB 120 A-24
3 HP (2.2 kW)
Dimension
RPM inlbs Class lbs
350 459 1.00 I 660 3 1520YA 5
250 643 1.00 I 745 3 1520YA 7
175 918 1.00 I 835 3 1520YA 10
A-22
146 1101 1.00 I 890 3 1520YA 12
117 1374 1.00 I 945 3 1520YA 15
87.5 1837 1.00 I 1035 3 1520YA 20
70.0 2296 1.00 I 1100 3 1520YA 25 A-22
58.3 2757 1.00 I 1155 3 1520YA 30 A-22
43.8 3669 1.00 I 1245 3 1531YA 40 A-23
35.0 4592 1.00 I 1310 3 1531YA 50 A-23

29.2 5504 1.00 I 1355 3 1531YA 60 A-23
21.9 7339 1.00 I 2170 3 60YA 80 A-24
17.5 9184 1.00 I 2205 3 60YA 100 A-24

14.6 11008 1.00 I 2205 3 60YA 120 A-24
Note: [1] Overhung Load values are based at a distance of 0.78 inch from the collar.
Hyponic
A-16
Gearmotors
5 HP (3.7 kW)
Dimension
RPM inlbs Class lbs
175 1531 1.00 I 1330 5 63YA 10
146 1835 1.00 I 1420 5 63YA 12
117 2289 1.00 I 1495 5 63YA 15
87.5 3061 1.00 I 1650 5 63YA 20

A-24
70.0 3827 1.00 I 1740 5 63YA 25
58.3 4594 1.00 I 1815 5 63YA 30
43.8 6115 1.00 I 1905 5 63YA 40

35.0 7653 1.00 I 1995 5 63YA 50
7.5 HP (5.5 kW)

Output Output Service Factor Hollow Bore Selection Gearmotors
Dimension
RPM inlbs Class lbs
Selection
Tables
175 2296 1.00 I 1330 8 64YA 10
146 2752 1.00 I 1420 8 64YA 12
117 3434 1.00 I 1495 8 64YA 15
87.5 4592 1.00 I 1650 8 64YA 20
A-24
70.0 5740 1.00 I 1740 8 64YA 25
58.3 6892 1.00 I 1815 8 64YA 30
43.8 9173 1.00 I 1905 8 64YA 40
60 Hz, Single Phase, 1750 RPM

1/8 HP (0.1 kW)
Dimension
SF Symbol Size Suffix Ratio Page
RPM inlbs Class lbs
350 19.1 2.00 III 1295
130 01 1120YC SG 5
250 26.8 2.00 III 1405
140 01 1120YC SG 7
175 38.3 2.00 III 1620
165 01 1120YC SG 10
146 45.9 2.00 III 1730
175 01 1120YC SG 12
117 57.2 2.00 III 1835
185 01 1120YC SG 15 A-27
87.5 76.5 2.00 III 2055
210 01 1120YC SG 20
70.0 95.7 2.00 III 2160

220 01 1120YC SG 25
58.3 115 2.00 III 2270
230 01 1120YC SG 30
43.8 153 2.00 III 3460
350 01 1220YC SG 40
35.0 191 2.00 III 3680
375 01 1220YC SG 50 A-27
29.2 229 2.00 III 3790
385 01 1220YC SG 60 A-27
21.9 306 2.00 III 6480
660 01 1330YC SG 80 A-28
17.5 383 2.00 III 6700

680 01 1330YC SG 100
14.6 459 2.00 III 6810
695 01 1330YC SG 120
11.7 572 2.00 III 6810
695 01 1330YC SG 150 A-28
8.75 765 1.74 II 6810
695 01 1330YB SG 200
7.29 919 1.45 II 6810
695 01 1330YB SG 240
Hyponic
A-17
Gearmotors
Selection Tables 60 Hz, Single Phase, 1750 RPM, cont.

1/4 HP (0.2 kW)
Dimension
RPM inlbs Class lbs
350 38.3 2.00 III 1835
185 02 1220YC SG 5
250 53.6 2.00 III 2055
210 02 1220YC SG 7
175 76.5 2.00 III 2270
230 02 1220YC SG 10
146 91.7 2.00 III 2380

240 02 1220YC SG 12
117 114 2.00 III 2600
265 02 1220YC SG 15 A-27
87.5 153 2.00 III 2910
295 02 1220YC SG 20
70.0 191 2.00 III 3020

305 02 1220YC SG 25
58.3 230 2.00 III 3240
330 02 1220YC SG 30
43.8 306 2.00 III 5620
570 02 1320YC SG 40
35.0 383 2.00 III 6060
615 02 1320YC SG 50 A-27
29.2 459 2.00 III 6260
635 02 1320YC SG 60 A-27
Gearmotors 21.9 612 2.00 III 9415
960 02 1430YC SG 80 A-28
17.5 765 2.00 III 9610
980 02 1430YC SG 100
Selection
14.6 917 2.00 III 9610

980 02 1430YC SG 120
Tables
11.7 1145 2.00 III 9610

980 02 1430YC SG 150 A-28
8.75 1531 1.74 II 9610
980 02 1430YB SG 200
7.29 1837 1.45 II 9610
980 02 1430YB SG 240
1/2 HP (0.4 kW)

Dimension
RPM inlbs Class lbs
350 76.5 1.88 II 305 05 1320YB SG 5
250 107 1.88 II 350 05 1320YB SG 7
175 153 1.88 II 385 05 1320YB SG 10
146 183 1.88 II 405 05 1320YB SG 12

117 229 1.88 II 440 05 1320YB SG 15 A-27
87.5 306 1.88 II 485 05 1320YB SG 20
70.0 383 1.88 II 505 05 1320YB SG 25

58.3 459 1.88 II 525 05 1320YB SG 30
43.8 612 1.88 II 855 05 1420YB SG 40
35.0 765 1.88 II 900 05 1420YB SG 50 A-27
29.2 917 1.88 II 935 05 1420YB SG 60 A-27
21.9 1223 1.88 II 1375 05 1530YB SG 80 A-28
17.5 1531 1.88 II 1400 05 1530YB SG 100

14.6 1835 1.88 II 1400 05 1530YB SG 120
11.7 2289 1.88 II 1400 05 1530YB SG 150 A-28
8.75 3061 1.63 II 1400 05 1530YB SG 200
7.29 3674 1.36 I 1400 05 1530YA SG 240
Hyponic
A-18
Gearmotors
Selection Tables Inverter Duty

1/8 HP (0.1 kW)
Output Service Factor Hollow Bore
Output Speed RPM (60 Hz) Selection Dimension
Torque Overhung
6 Hz 60 Hz 120 Hz[1] (60 Hz) AGMA Load [2] HP Frame Nominal Page
SF Suffix
inlbs Class (60 Hz) lbs Symbol Size Ratio
36.0 360 720 18.6 2.00 III 130 01 1120YC AV 5

25.7 257 514 26.1 2.00 III 140 01 1120YC AV 7
18.0 180 360 37.2 2.00 III 165 01 1120YC AV 10
15.0 150 300 44.6 2.00 III 175 01 1120YC AV 12

12.0 120 240 55.8 2.00 III 185 01 1120YC AV 15 A-29
9.0 90.0 180 74.4 2.00 III 210 01 1120YC AV 20
7.20 72.0 144 93.0 2.00 III 220 01 1120YC AV 25

6.00 60.0 120 112 2.00 III 230 01 1120YC AV 30
4.50 45.0 90.0 149 2.00 III 350 01 1220YC AV 40
3.60 36.0 72.0 186 2.00 III 375 01 1220YC AV 50 A-29
3.00 30.0 60.0 223 2.00 III 385 01 1220YC AV 60 A-29
2.25 22.5 45.0 298 2.00 III 660 01 1330YC AV 80 A-30 Gearmotors
1.80 18.0 36.0 372 2.00 III 680 01 1330YC AV 100
Selection
Tables
1.50 15.0 30.0 446 2.00 III 695 01 1330YC AV 120
1.20 12.0 24.0 558 2.00 III 695 01 1330YC AV 150 A-30
0.900 9.00 18.0 744 2.00 III 695 01 1330YC AV 200
0.750 7.50 15.0 893 1.80 II 695 01 1330YB AV 240
1/4 HP (0.2 kW)

Output Speed RPM Selection Dimension
Torque (60 Hz) Overhung
SF Suffix
36.0 360 720 37.2 2.00 III 185 02 1220YC AV 5
25.7 257 514 52.1 2.00 III 210 02 1220YC AV 7
18.0 180 360 74.4 2.00 III 230 02 1220YC AV 10
15.0 150 300 89.3 2.00 III 240 02 1220YC AV 12
12.0 120 240 112 2.00 III 265 02 1220YC AV 15 A-29
9.00 90.0 180 149 2.00 III 295 02 1220YC AV 20
7.20 72.0 144 186 2.00 III 305 02 1220YC AV 25
6.00 60.0 120 223 2.00 III 330 02 1220YC AV 30
4.50 45.0 90.0 298 2.00 III 570 02 1320YC AV 40
3.60 36.0 72.0 372 2.00 III 615 02 1320YC AV 50 A-29
3.00 30.0 60.0 446 2.00 III 638 02 1320YC AV 60 A-29
2.25 22.5 45.0 595 2.00 III 960 02 1430YC AV 80 A-30
1.80 18.0 36.0 744 2.00 III 980 02 1430YC AV 100
1.50 15.0 30.0 893 2.00 III 980 02 1430YC AV 120
1.20 12.0 24.0 1116 2.00 III 980 02 1430YC AV 150 A-30
0.900 9.00 18.0 1488 2.00 III 980 02 1430YC AV 200
0.750 7.50 15.0 1786 1.80 II 980 02 1430YB AV 240
Notes: [1] 3600 RPM (120 Hz) is the maximum allowable input speed.
Hyponic
A-19
Gearmotors
Selection Tables Inverter Duty, cont.

1/2 HP (0.4 kW)
Torque Overhung
SF Suffix
36.0 360 720 74.4 1.88 II 305 05 1320YB AV 5
25.7 257 514 104 1.88 II 350 05 1320YB AV 7
18.0 180 360 149 1.88 II 385 05 1320YB AV 10
15.0 150 300 179 1.88 II 405 05 1320YB AV 12
12.0 120 240 223 1.88 II 440 05 1320YB AV 15 A-29
9.00 90.0 180 298 1.88 II 485 05 1320YB AV 20
7.20 72.0 144 372 1.88 II 505 05 1320YB AV 25
6.00 60.0 120 446 1.88 II 525 05 1320YB AV 30
4.50 45.0 90.0 595 1.88 II 855 05 1420YB AV 40
3.60 36.0 72.0 744 1.88 II 900 05 1420YB AV 50 A-29
3.00 30.0 60.0 893 1.88 II 935 05 1420YB AV 60 A-29
2.25 22.5 45.0 1190 1.88 II 1375 05 1530YB AV 80 A-30
Gearmotors
1.80 18.0 36.0 1488 1.88 II 1400 05 1530YB AV 100
1.50 15.0 30.0 1786 1.88 II 1400 05 1530YB AV 120
Selection
Tables
1.20 12.0 24.0 2232 1.88 II 1400 05 1530YB AV 150 A-30

0.900 9.00 18.0 2976 1.88 II 1400 05 1530YB AV 200
0.750 7.50 15.0 3571 1.88 II 1400 05 1530YB AV 240
1 HP (0.75 kW)
SF Suffix
36.0 360 720 149 2.00 III 460 1 1420YC AV 5
25.7 257 514 208 2.00 III 515 1 1420YC AV 7
18.0 180 360 298 2.00 III 580 1 1420YC AV 10
15.0 150 300 357 2.00 III 615 1 1420YC AV 12
12.0 120 240 446 2.00 III 660 1 1420YC AV 15 A-29
9.00 90.0 180 595 2.00 III 715 1 1420YC AV 20
7.20 72.0 144 744 2.00 III 760 1 1420YC AV 25
6.00 60.0 120 893 2.00 III 805 1 1420YC AV 30
4.50 45.0 90.0 1190 2.00 III 1245 1 1520YC AV 40
3.60 36.0 72.0 1488 2.00 III 1310 1 1520YC AV 50 A-29
3.00 30.0 60.0 1786 2.00 III 1355 1 1520YC AV 60 A-29
2.25 22.5 45.0 2381 2.00 III 1375 1 1531YC AV 80 A-30
1.80 18.0 36.0 2976 2.93 III 2205 1 60YC AV 100
A-31
1.50 15.0 30.0 3571 2.93 III 2205 1 60YC AV 120
Hyponic
A-20
Gearmotors
Selection Tables Inverter Duty, cont.
2 HP (1.5 kW)
Torque Overhung
SF Suffix
36.0 360 720 298 1.47 II 660 2 1520YB AV 5
25.7 257 514 417 1.47 II 745 2 1520YB AV 7
18.0 180 360 595 1.47 II 835 2 1520YB AV 10
A-29
15.0 150 300 714 1.47 II 890 2 1520YB AV 12
12.0 120 240 893 1.47 II 945 2 1520YB AV 15
9.00 90.0 180 1190 1.47 II 1035 2 1520YB AV 20
7.20 72.0 144 1488 1.47 II 1100 2 1520YB AV 25 A-29
6.00 60.0 120 1786 1.47 II 1155 2 1520YB AV 30 A-29
4.50 45.0 90.0 2381 1.47 II 1245 2 1531YB AV 40 A-30
3.60 36.0 72.0 2976 1.47 II 1310 2 1531YB AV 50 A-30
3.00 30.0 60.0 3571 1.47 II 1355 2 1531YB AV 60 A-30
2.25 22.5 45.0 4762 1.47 II 2170 2 60YB AV 80 A-31
Gearmotors
1.80 18.0 36.0 5952 1.47 II 2205 2 60YB AV 100
A-31
1.50 15.0 30.0 7143 1.47 II 2205 2 60YB AV 120
Selection
Tables
3 HP (2.2 kW)
SF Suffix
18.0 180 360 893 1.68 II 1330 3 63YB AV 10
15.0 150 300 1071 1.68 II 1420 3 63YB AV 12
12.0 120 240 1339 1.68 II 1495 3 63YB AV 15
9.00 90.0 180 1786 1.68 II 1650 3 63YB AV 20
A-31
7.20 72.0 144 2232 1.68 II 1710 3 63YB AV 25
6.00 60.0 120 2679 1.68 II 1815 3 63YB AV 30
4.50 45.0 90.0 3571 1.68 II 1905 3 63YB AV 40
3.60 36.0 72.0 4464 1.68 II 1995 3 63YB AV 50
5 HP (3.7 kW)
SF Suffix
18.0 180 360 1488 1.49 II 1330 5 64YB AV 10
15.0 150 300 1786 1.49 II 1420 5 64YB AV 12
12.0 120 240 2232 1.49 II 1495 5 64YB AV 15
9.00 90.0 180 2976 1.49 II 1650 5 64YB AV 20 A-31
7.20 72.0 144 3720 1.49 II 1740 5 64YB AV 25
6.00 60.0 120 4464 1.49 II 1815 5 64YB AV 30
4.50 45.0 90.0 5952 1.49 II 1905 5 64YB AV 40
Hyponic
A-21
Gearmotors
Hollow Shaft Type, 3-Phase Motor

RNYM01~3 1120/1220/1320/1420/1520Y (-B)
C
F G F
D D L N
P P
A
ZA
L K
B DIA B DIA A R
J E MP
DIA
AB
4X H DIA
A
K E
A X
O
S
M DIA
T DIA U DIA BORE
Gearmotors
Inch
W W
AA
Dimensions
Model A B min B max D E F G H J K L N P R X

RNYM01~02-1120Y 3.54 2.046 2.047 1.30 1.65 0.31 2.60 0.26 1.97 1.26 1.57 3.23 0.24 0.79 0.87
RNYM01~05-1220Y 4.53 3.070 3.071 1.46 2.24 0.35 2.91 0.35 2.60 1.57 1.93 3.78 0.20 1.10 0.79
RNYM02~1-1320Y 5.20 3.345 3.346 1.81 2.44 0.35 3.62 0.43 2.91 1.81 2.28 4.69 0.20 1.08 1.34
RNYM05~2-1420Y 6.22 3.739 3.740 2.32 2.95 0.39 4.65 0.55 3.46 2.24 2.76 5.75 0.20 0.79 1.69
RNYM1~3-1520Y 7.01 4.329 4.331 2.68 3.15 0.39 5.35 0.55 3.70 2.76 3.31 7.01 0.20 1.10 2.68
Output Shaft
Model
U min U max V Key M O S T W
RNYM01~02-1120Y 0.750 0.751 3.23 3/16X3/16 0.77 0.63 0.039 0.796 1.18
RNYM01~05-1220Y 1.000 1.001 3.62 1/4X1/4 1.02 0.87 0.046 1.066 1.50
RNYM02~1-1320Y 1.250 1.252 4.33 1/4X1/4 1.27 0.87 0.056 1.330 1.81
RNYM05~2-1420Y 1.375 1.377 5.43 5/16X5/16 1.40 1.02 0.056 1.461 2.05
RNYM1~3-1520Y 1.500 1.502 6.14 3/8X3/8 1.52 1.18 0.056 1.594 2.64
Standard Motor Brakemotor

Model HP AB ZA
C MP WT (LB) C MP WT (LB)
RNYM01-1120Y(-B)-5~60 1/8 5.04 - 10.55 4.69 13 11.93 4.88 17
RNYM02-1120Y(-B)-5~30 1/4 5.04 - 12.20 4.88 15 13.46 4.88 19
RNYM01-1220Y(-B)-40~60 1/8 5.04 - 11.46 4.69 15 12.83 4.88 19
RNYM02-1220Y(-B)-5~60 1/4 5.04 - 13.11 4.88 19 14.37 4.88 22
RNYM03-1220Y(-B)-5~30 1/3 5.04 - 13.90 4.88 21 15.16 4.88 24
RNYM05-1220Y(-B)-5~30 1/2 5.04 - 13.90 4.88 21 15.16 4.88 24
RNYM02-1320Y(-B)-40~60 1/4 5.04 - 14.21 4.88 22 15.47 4.88 24
RNYM03-1320Y(-B)-40~60 1/3 5.04 - 15.00 4.88 24 16.26 4.88 29
RNYM05-1320Y(-B)-5~60 1/2 5.04 - 15.00 4.88 24 16.26 4.88 29
RNYM08-1320Y(-B)-5~30 3/4 5.43 3.41 16.65 6.10 29 18.35 6.10 35
RNYM1-1320Y(-B)-5~30 1 5.43 3.41 16.65 6.10 33 18.35 6.10 37
RNYM05-1420Y(-B)-40~60 1/2 5.04 - 16.22 4.88 33 17.48 4.88 35
RNYM08-1420Y(-B)-40~60 3/4 5.43 3.66 18.66 6.10 37 20.35 6.10 42
RNYM1-1420Y(-B)-5~60 1 5.43 3.66 18.66 6.10 40 20.35 6.10 44
RNYM1H-1420Y(-B)-5~30 1.5 5.63 3.86 19.84 6.57 46 22.28 6.57 55
RNYM2-1420Y(-B)-5~30 2 5.63 3.86 19.84 6.57 49 22.28 6.57 57
RNYM1-1520Y(-B)-40~60 1 5.43 4.45 19.61 6.10 57 21.30 6.10 62
RNYM1H-1520Y(-B)-40~60 1.5 5.63 4.65 21.02 6.57 64 23.46 6.57 73
RNYM2-1520Y(-B)-5~60 2 5.63 4.65 21.02 6.57 68 23.46 6.57 77
RNYM3-1520Y(-B)-5~30 3 5.91 4.88 21.77 7.09 75 24.25 7.09 86
Dimensions shown are for reference only and are subject to change without notice, unless certified.
Certified prints are available after receipt of an order; consult factory.
Hyponic
A-22
Gearmotors
RNYM01~3 1230/1330/1430/1530/1531Y (-B)

C
P D D P N
L J
A
ZA
L
K
B DIA B DIA MP DIA
R
A
E
J
AB
I DIA
A
Q 4X H DIA K E
F G F A X
O M DIA
S
T DIA U DIA BORE

Gearmotors
W W
Dimensions
V A-A
Inch
Model A B min B max D E F G H I J K L N P Q R X
RNYM01-1230Y 5.00 3.070 3.071 1.61 2.56 0.35 3.23 0.35 0.55 2.99 1.57 2.01 3.74 0.20 - 0.51 0.31
RNYM01~02-1330Y 5.98 3.345 3.346 1.81 3.11 0.35 3.62 0.43 0.69 3.62 1.85 2.36 4.25 0.20 - 0.43 0.14
RNYM02~05-1430Y 7.01 3.739 3.740 2.32 3.62 0.39 4.65 0.55 0.79 4.25 2.13 2.76 5.12 0.20 4.13 0.55 0.31
RNYM05~1-1530Y 8.39 4.329 4.331 2.68 4.29 0.39 5.35 0.71 - 5.08 2.52 3.31 6.18 0.20 - 0.67 0.37
RNYM1~3-1531Y 8.39 4.329 4.331 2.68 4.29 0.39 5.35 0.71 - 5.08 2.52 3.31 6.18 0.20 - 0.67 0.37
Output Shaft
Model
RNYM01-1230Y 1.000 1.001 3.94 1/4X1/4 1.02 0.87 0.046 1.066 1.50
RNYM01~02-1330Y 1.250 1.252 4.33 1/4X1/4 1.27 0.87 0.056 1.330 1.81
RNYM02~05-1430Y 1.375 1.377 5.43 5/16X5/16 1.40 1.02 0.056 1.461 2.05
RNYM05~1-1530Y 1.500 1.502 6.14 3/8X3/8 1.52 1.18 0.056 1.594 2.64
RNYM1~3-1531Y 1.500 1.502 6.14 3/8X3/8 1.52 1.18 0.056 1.594 2.64

Model HP AB ZA
RNYM01-1230Y(-B)-80~240 1/8 5.04 - 11.50 4.69 17 12.87 4.88 20
RNYM01-1330Y(-B)-80~240 1/8 5.04 - 12.36 4.69 20 13.74 4.88 22
RNYM02-1330Y(-B)-80~240 1/4 5.04 - 14.02 4.88 22 15.28 4.88 24
RNYM02-1430Y(-B)-80~240 1/4 5.04 - 15.12 4.88 33 16.38 4.88 35
RNYM03-1430Y(-B)-80~240 1/3 5.04 - 15.91 4.88 35 17.17 4.88 37
RNYM05-1430Y(-B)-80~240 1/2 5.04 - 15.91 4.88 35 17.17 4.88 37
RNYM05-1530Y(-B)-80~240 1/2 5.04 - 17.20 4.88 51 18.46 4.88 53
RNYM08-1530Y(-B)-80~240 3/4 5.43 3.78 19.61 6.10 53 21.30 6.10 57
RNYM1-1530Y(-B)-80~240 1 5.43 3.78 19.61 6.10 55 21.30 6.10 62
RNYM1-1531Y(-B)-80 1 5.43 4.45 19.61 6.10 57 21.30 6.10 62
RNYM1H-1531Y(-B)-80 1.5 5.63 4.65 20.79 6.57 64 23.23 6.57 73
RNYM2-1531Y(-B)-40~80 2 5.63 4.65 20.79 6.57 66 23.23 6.57 75
RNYM3-1531Y(-B)-40~80 3 5.91 4.88 21.57 7.09 75 24.06 7.09 86
Hyponic
A-23
Gearmotors

RNYM1H~8 60/63/64Y (-B)
D D C
P P
ZA
LK
B DIA B DIA R MP
A DIA
J E
AB
I DIA
4X H DIA K E
Q
L J
F G F
A
O
S M DIA
Gearmotors
T DIA U DIA BORE
Dimensions
W
W
V A-A
Inch
Model A B min B max D E F G H I J K L P Q R
RNYM1H~3-60Y 11.02 5.904 5.906 3.66 5.71 0.75 7.32 0.87 1.26 6.69 3.35 4.33 0.47 6.46 1.06
RNYM5-63Y 11.02 5.904 5.906 3.66 5.71 0.75 7.32 0.87 1.26 6.69 3.35 4.33 0.47 6.46 1.06
RNYM8-64Y 11.02 5.904 5.906 3.66 5.71 0.75 7.32 0.87 1.26 6.69 3.35 4.33 0.47 6.46 1.06
Output Shaft
Model
RNYM1H~3-60Y 2.000 2.002 8.82 1/2X1/2 2.02 1.57 0.068 2.122 3.35
RNYM5-63Y 2.000 2.002 8.82 1/2X1/2 2.02 1.57 0.068 2.122 3.35
RNYM8-64Y 2.000 2.002 8.82 1/2X1/2 2.02 1.57 0.068 2.122 3.35

Model HP AB ZA
RNYM1H-60Y(-B)-100~120 1.5 5.63 6.30 23.35 6.57 187 25.79 6.57 198
RNYM2-60Y(-B)-80~120 2 5.63 6.30 23.35 6.57 187 25.79 6.57 198
RNYM3-60Y(-B)-80~120 3 5.91 6.30 24.57 7.09 198 27.05 7.09 214
RNYM5-63Y(-B)-10~50 5 6.54 6.30 26.65 8.74 225 29.49 8.74 247
RNYM8-64Y(-B)-10~40 7.5 6.54 6.30 28.39 8.74 243 31.22 8.74 262
Hyponic
A-24
Gearmotors
RNYM01~02 361/461Y (-B)
C
D D N
P P
MP
L K DIA
R
B DIA B DIA
A AB
J E
I DIA
Q K E
4X H DIA
F G F L J
O M DIA A
Gearmotors
S
Dimensions
T DIA U DIA BORE
W
W
V
Inch
Model A B min B max D E F G H I J K L N P Q R
RNYM01-361 5.98 3.345 3.346 1.81 3.11 0.35 3.62 0.43 0.69 3.62 1.85 2.36 4.13 0.20 3.19 1.18
RNYM02-461 7.01 3.739 3.740 2.32 3.62 0.39 4.65 0.55 0.79 4.25 2.13 2.76 4.76 0.20 4.13 1.06
Output Shaft
Model
RNYM01-361 1.000 1.002 4.33 1/4X1/4 1.02 0.87 0.046 1.066 1.81
RNYM02-461 1.438 1.439 5.43 3/8X3/8 1.46 1.02 0.056 1.528 2.05

Model HP AB
RNYM01-361(-B)-300~1440 1/8 5.04 13.86 4.69 25 15.24 4.88 29
RNYM02-461(-B)-300~1440 1/4 5.04 17.01 4.88 32 18.27 4.88 35
Hyponic
A-25
Gearmotors

RNYM03~1 56Y (-B)
D D
C
P P
N
ZA
L MP
K DIA
R
B DIA B DIA
A AB
J E
I DIA
Q 4X H DIA
K E
F G F L J
A
O
M DIA
Gearmotors
S
Dimensions
T DIA U DIA BORE
W W A-A
V
Inch
Model A B min B max D E F G H I J K L N P Q R
RNYM03~1-56Y 8.39 4.329 4.331 2.76 4.29 0.39 5.51 0.71 1.02 5.08 2.52 3.31 5.69 0.20 4.80 1.89
Output Shaft
Model
RNYM03~1-56Y 1.508 1.689 6.30 3/8X3/8 1.71 1.18 0.068 1.792 2.64

Model HP AB ZA
RNYM03-56Y(-B)-300~1440 1/3 5.04 - 19.49 4.88 57 20.75 4.88 60
RNYM05-56Y(-B)-300~1440 1/2 5.04 - 19.49 4.88 57 20.75 4.88 60
RNYM08-56Y(-B)-300~480 3/4 5.43 6.34 21.34 5.83 66 23.03 5.83 73
RNYM1-56Y(-B)-300~480 1 5.43 6.34 21.34 5.83 66 23.03 5.83 73
Hyponic
A-26
Gearmotors
Hollow Shaft Type, Single Phase Motor

RNYM01~05 1120/1220/1320/1420Y SG (-B)
F G C
F
D D L N
P P
A
ZA
L K
B DIA B DIA
A R MP DIA
J E
4X H DIA A AB
K E
A X
O
S M DIA
Gearmotors
Dimensions
T DIA U DIA BORE
W
W
V A-A
Inch
RNYM01-1120Y-SG 3.54 2.046 2.047 1.30 1.65 0.31 2.60 0.26 1.97 1.26 1.57 3.23 0.24 0.79 0.87
RNYM01~02-1220Y-SG 4.53 3.070 3.071 1.46 2.24 0.35 2.91 0.35 2.60 1.57 1.93 3.78 0.20 1.10 0.79
RNYM02~05-1320Y-SG 5.20 3.345 3.346 1.81 2.44 0.35 3.62 0.43 2.91 1.81 2.28 4.69 0.20 1.08 1.34
RNYM05-1420Y-SG 6.22 3.739 3.740 2.32 2.95 0.39 4.65 0.55 3.46 2.24 2.76 5.75 0.20 0.79 1.69
Output Shaft
Model
RNYM01-1120Y-SG 0.750 0.751 3.23 3/16X3/16 0.77 0.63 0.039 0.796 1.18
RNYM01~02-1220Y-SG 1.000 1.001 3.62 1/4X1/4 1.02 0.87 0.046 1.066 1.50
RNYM02~05-1320Y-SG 1.250 1.252 4.33 1/4X1/4 1.27 0.87 0.056 1.330 1.81
RNYM05-1420Y-SG 1.375 1.377 5.43 5/16X5/16 1.40 1.02 0.056 1.461 2.05

Model HP AB ZB
RNYM01-1120Y-SG(-B)-5~60 1/8 4.72 - 12.80 4.88 18 13.46 4.88 21
RNYM01-1220Y-SG(-B)-40~60 1/8 4.72 - 13.70 4.88 19 14.37 4.88 24
RNYM02-1220Y-SG(-B)-5~60 1/4 4.72 - 14.49 4.88 22 15.16 4.88 26
RNYM02-1320Y-SG(-B)-40~60 1/4 4.72 - 15.55 4.88 26 16.26 4.88 31
RNYM05-1320Y-SG(-B)-5~60 1/2 5.12 3.37 16.65 6.10 35 18.35 6.10 40
RNYM05-1420Y-SG(-B)-40~60 1/2 5.12 3.66 18.66 6.10 42 20.35 6.10 46
Hyponic
A-27
Gearmotors
Hollow Shaft Type, Single Phase Motor

RNYM01~05 1230/1330/1430/1530Y SG (-B)
F F C
G
L N
P D D P
A
ZA
L
K
B DIA B DIA MP
R DIA
A
E
J
AB
4X H DIA
A
K E
O A X
Gearmotors S
M DIA
Dimensions
T DIA U DIA BORE
W W
V A-A
Inch
RNYM01-1330Y-SG 5.98 3.345 3.346 1.81 3.11 0.35 3.62 0.43 0.69 3.62 1.85 2.36 4.25 0.20 3.19 0.43 0.14
RNYM02-1430Y-SG 7.01 3.739 3.740 2.32 3.62 0.39 4.65 0.55 0.79 4.25 2.13 2.76 5.12 0.20 4.13 0.55 0.31
RNYM05-1530Y-SG 8.39 4.329 4.331 2.68 4.29 0.39 5.35 0.71 - 5.08 2.52 3.31 6.18 0.20 - 0.67 0.37
Output Shaft
Model
RNYM01-1330Y-SG 1.250 1.252 4.33 1/4X1/4 1.27 0.87 0.056 1.330 1.81
RNYM02-1430Y-SG 1.375 1.377 5.43 5/16X5/16 1.40 1.02 0.056 1.461 2.05
RNYM05-1530Y-SG 1.500 1.502 6.14 3/8X3/8 1.52 1.18 0.056 1.594 2.64

Model HP AB ZA
RNYM01-1330Y-SG(-B)-80~240 1/8 4.72 - 14.57 4.88 22 15.28 4.88 24
RNYM02-1430Y-SG(-B)-80~240 1/4 4.72 - 16.46 4.88 35 17.17 4.88 37
RNYM05-1530Y-SG(-B)-80~240 1/2 5.12 3.78 19.61 6.10 55 21.30 6.10 62
Hyponic
A-28
Gearmotors
Hollow Shaft Type, Inverter Duty

RNYM01~2 1120/1220/1320/1420/1520Y AV (-B)
F G C
F
D D L N
P P
A
ZA
L K
B DIA B DIA A
R
J E
MP
DIA
AB
4X H DIA
A
K E
A X
O
S
M DIA Gearmotors
Dimensions
T DIA U DIA BORE
W W
V A-A
Inch
RNYM01-1120Y-AV 3.54 2.046 2.047 1.30 1.65 0.31 2.60 0.26 1.97 1.26 1.57 3.23 0.24 0.79 0.87
RNYM01~02-1220Y-AV 4.53 3.070 3.071 1.46 2.24 0.35 2.91 0.35 2.60 1.57 1.93 3.78 0.20 1.10 0.79
RNYM02~05-1320Y-AV 5.20 3.345 3.346 1.81 2.44 0.35 3.62 0.43 2.91 1.81 2.28 4.69 0.20 1.08 1.34
RNYM05~1-1420Y-AV 6.22 3.739 3.740 2.32 2.95 0.39 4.65 0.55 3.46 2.24 2.76 5.75 0.20 0.79 1.69
RNYM1~2-1520Y-AV 7.01 4.329 4.331 2.68 3.15 0.39 5.35 0.55 3.70 2.76 3.31 7.01 0.20 1.10 2.68
Output Shaft
Model
RNYM01-1120Y-AV 0.750 0.751 3.23 3/16X3/16 0.77 0.63 0.039 0.796 1.18
RNYM01~02-1220Y-AV 1.000 1.001 3.62 1/4X1/4 1.02 0.87 0.046 1.066 1.50
RNYM02~05-1320Y-AV 1.250 1.252 4.33 1/4X1/4 1.27 0.87 0.056 1.330 1.81
RNYM05~1-1420Y-AV 1.375 1.377 5.43 5/16X5/16 1.40 1.02 0.056 1.461 2.05
RNYM1~2-1520Y-AV 1.500 1.502 6.14 3/8X3/8 1.52 1.18 0.056 1.594 2.64

Model HP AB ZA
RNYM01-1120Y-AV(-B)-5~30 1/8 5.04 - 12.20 4.88 15 13.46 4.88 19
RNYM01-1220Y-AV(-B)-40~60 1/8 5.04 - 13.11 4.88 19 14.37 4.88 22
RNYM02-1220Y-AV(-B)-5~30 1/4 5.04 - 13.90 4.88 21 15.16 4.88 24
RNYM02-1320Y-AV(-B)-40~60 1/4 5.04 - 15.00 4.88 24 16.26 4.88 29
RNYM05-1320Y-AV(-B)-5~60 1/2 5.43 3.37 16.65 6.10 33 18.35 6.10 37
RNYM05-1420Y-AV(-B)-40~60 1/2 5.43 3.66 18.66 6.10 40 20.35 6.10 44
RNYM1-1420Y-AV(-B)-5~30 1 5.63 3.86 19.84 6.57 49 22.28 6.57 57
RNYM1-1520Y-AV(-B)-40~60 1 5.63 3.58 21.02 6.57 68 23.46 6.57 77
RNYM2-1520Y-AV(-B)-5~30 2 5.91 3.78 21.77 7.09 75 24.25 7.09 86
Hyponic
A-29
Gearmotors
Hollow Shaft Type, Inverter Duty

RNYM01~2 1330/1430/1530/1531Y AV (-B)
C
P D D P N
L J
A
ZA
L
K
B DIA B DIA MP DIA
R
A
E
J
AB
I DIA
A
Q 4X H DIA K E
F G F A X
O M DIA
S
Gearmotors
T DIA U DIA BORE
Dimensions
W W
V A-A
Inch
RNYM01-1330Y-AV 5.98 3.345 3.346 1.81 3.11 0.35 3.62 0.43 0.69 3.62 1.85 2.36 4.25 0.20 3.19 0.43 0.14
RNYM02-1430Y-AV 7.01 3.739 3.740 2.32 3.62 0.39 4.65 0.55 0.79 4.25 2.13 2.76 5.12 0.20 4.13 0.55 0.31
RNYM05-1530Y-AV 8.39 4.329 4.331 2.68 4.29 0.39 5.35 0.71 - 5.08 2.52 3.31 6.18 0.20 - 0.67 0.37
RNYM1~2-1531Y-AV 8.39 4.329 4.331 2.68 4.29 0.39 5.35 0.71 - 5.08 2.52 3.31 6.18 0.20 - 0.67 0.37
Output Shaft
Model
RNYM01-1330Y-AV 1.250 1.252 4.33 1/4X1/4 1.27 0.87 0.056 1.330 1.81
RNYM02-1430Y-AV 1.375 1.377 5.43 5/16X5/16 1.40 1.02 0.056 1.461 2.05
RNYM05-1530Y-AV 1.500 1.502 6.14 3/8X3/8 1.52 1.18 0.056 1.594 2.64
RNYM1~2-1531Y-AV 1.500 1.502 6.14 3/8X3/8 1.52 1.18 0.056 1.594 2.64

Model HP AB ZA
RNYM01-1330Y-AV(-B)-80~240 1/8 5.04 - 14.02 4.88 22 15.28 4.88 24
RNYM02-1430Y-AV(-B)-80~240 1/4 5.04 - 15.91 4.88 35 17.17 4.88 37
RNYM05-1530Y-AV(-B)-80~240 1/2 5.43 3.78 19.61 6.10 55 21.30 6.10 62
RNYM1-1531Y-AV(-B)-80 1 5.63 3.98 20.79 6.57 66 23.23 6.57 75
RNYM2-1531Y-AV(-B)-40~60 2 5.91 4.21 21.57 7.09 75 24.06 7.09 86
Hyponic
A-30
Gearmotors
RNYM2~5 60/63/64Y AV (-B)
D D C
P P
ZA
L K
B DIA B DIA MP
R
A DIA
J E
AB
I DIA
4X H DIA K E
Q
L J
F G F
A
O
S M DIA Gearmotors
Dimensions
T DIA U DIA BORE
W
W
V A-A
Inch
Model A B min B max D E F G H I J K L P Q R
RNYM2-60Y-AV 11.02 5.904 5.906 3.66 5.71 0.75 7.32 0.87 1.26 6.69 3.35 4.33 0.47 6.46 1.06
RNYM3-63Y-AV 11.02 5.904 5.906 3.66 5.71 0.75 7.32 0.87 1.26 6.69 3.35 4.33 0.47 6.46 1.06
RNYM5-64Y-AV 11.02 5.904 5.906 3.66 5.71 0.75 7.32 0.87 1.26 6.69 3.35 4.33 0.47 6.46 1.06
Output Shaft
Model
RNYM2-60Y-AV 2.000 2.002 8.82 1/2X1/2 2.02 1.57 0.068 2.122 3.35
RNYM3-63Y-AV 2.000 2.002 8.82 1/2X1/2 2.02 1.57 0.068 2.122 3.35
RNYM5-64Y-AV 2.000 2.002 8.82 1/2X1/2 2.02 1.57 0.068 2.122 3.35

Model HP AB ZA
RNYM2-60Y-AV(-B)- 80~120 2 5.91 6.30 24.57 7.09 198 27.05 7.09 214
RNYM3-63Y-AV(-B)- 10~50 3 6.54 6.30 26.65 8.74 225 29.49 8.74 245
RNYM5-64Y-AV(-B)- 10~40 5 6.54 6.30 28.39 8.74 243 31.22 8.74 262
Hyponic
A-31
Gearmotors
Notes
Gearmotors
Hyponic
A-32
Reducers
Speed Reducers
B
Hollow Shaft Type
Reducers
Selection
Tables
Hyponic
B-1
Reducers
Product Range
Table B-1 Reducer Product Range
Frame Nominal Output Torque at 1750 Stock
Size Ratio (:1) RPM Input (inlbs) [1] Adaptor[2]
1120 5 ~ 60 41.1 ~ 246 42C ~ 56C
1230 80 ~ 240 328 ~ 867 42C ~ 56C
1220 5 ~ 60 82.1 ~ 493 42C ~ 56C
1330 80 ~ 240 657 ~ 1724 42C ~ 56C
1320 5 ~ 60 165 ~ 982 56C ~ 145TC
1430 80 ~ 240 1314 ~ 3448 42C ~ 56C
1420 5 ~ 60 316 ~ 1970 56C ~ 145TC
1530 80 ~ 240 2627 ~ 6470 56C ~ 145TC
1520 5 ~ 60 452 ~ 3793 56C ~ 184TC
1531 40 ~ 80 3612 ~ 5419 56C ~ 184TC
Table B-2 Standard Specifications
Item Standard Specification
Lubrication Grease Lubricated. Filled with special high-grade grease prior to shipment from factory.
Reducer Reduction Combination of Hypoid gear and Involute gear.
Material Casing: Aluminum Alloy, Gear: Chrome-Molybdenum steel
Installation Indoor (free from water)

Reducers
Temperature 14 to 104°F
Product
Range
Ambient Conditions Humidity 85% maximum - no condensation
Altitude 3280 feet
Atmosphere Free from corrosive gas, explosive gas, or steam. Area to be well ventilated.
Installation Angle No Limitation
Table B-3 Recommended Reducer Service Factors

LOAD CLASSIFICATIONS
PRIME MOVER DURATION OF SERVICE UNIFORM MODERATE SHOCK HEAVY SHOCK
AGMA AGMA AGMA
Occasional 1/2 hr. per day 0.50[3] 0.80[3] 1.25
Intermittent 3 hrs. per day 0.80[3] 1.00 1.50

ELECTRIC
MOTOR
Up to 10 hrs. per day 1.00 1.25 1.75
24 hours per day 1.25 1.50 2.00
Notes: [1] Please refer to the Reducer Selection Tables for additional input speeds and ratings.
[2] Please consult the factory for availablity of motor adaptors not listed.
[3] Maximum momentary or starting load must not exceed 250% of gear reducer rating (rating meaning service factor of 1.0). Time
specified for occasional and intermittent service refers to total operating time per day.
Hyponic
B-2
Reducers

Table B-4 Load Classification Listed by Application
TYPE OF TYPE OF TYPE OF TYPE OF TYPE OF TYPE OF
APPLICATION LOAD APPLICATION LOAD APPLICATION LOAD
Agitators Large (industrial) . . . . . . . . . . . . . . . . . . . . . . . M Paper Mills

Pure liquids . . . . . . . . . . . . . . . . . . . . . . . . . . . . U Light (small diameter) . . . . . . . . . . . . . . . . . . . . U Agitators (mixers) . . . . . . . . . . . . . . . . . . . . . . . M
Liquids and solids . . . . . . . . . . . . . . . . . . . . . . . M Feeders Barker, hydraulic . . . . . . . . . . . . . . . . . . . . . . . M
Variable-density liquids . . . . . . . . . . . . . . . . . . M Apron . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . M Barker, mechnical . . . . . . . . . . . . . . . . . . . . . . M
Blowers Belt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . M Barking drum . . . . . . . . . . . . . . . . . . . . . . . . . . H
Centrifugal . . . . . . . . . . . . . . . . . . . . . . . . . . . . U Disc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . U Beater and pulper . . . . . . . . . . . . . . . . . . . . . . . M
Lobe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . M Reciprocating . . . . . . . . . . . . . . . . . . . . . . . . . . H Bleacher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . U
Vane . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . U Screw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . M Calenders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . M
Brewing and Distilling Food Industry Calenders, super . . . . . . . . . . . . . . . . . . . . . . . H
Bottling machinery . . . . . . . . . . . . . . . . . . . . . . U Beet slicer . . . . . . . . . . . . . . . . . . . . . . . . . . . . M Converting machine (except cutters, platers) . . M
Brew kettles, cont. duty . . . . . . . . . . . . . . . . . . . U Cereal cooker . . . . . . . . . . . . . . . . . . . . . . . . . . U Conveyors . . . . . . . . . . . . . . . . . . . . . . . . . . . . U
Cookers, cont. duty . . . . . . . . . . . . . . . . . . . . . . U Dough mixer . . . . . . . . . . . . . . . . . . . . . . . . . . . M Couch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . M
Mash tubs, cont. duty . . . . . . . . . . . . . . . . . . . . U Meat grinders . . . . . . . . . . . . . . . . . . . . . . . . . . M Cutters, platers . . . . . . . . . . . . . . . . . . . . . . . . . H
Scale hopper, frequent starts . . . . . . . . . . . . . . M Generators (Not Welding) . . . . . . . . . . . . . . . . . . . . U Cylinders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . M
Can Filling Machines . . . . . . . . . . . . . . . . . . . . . . . . U Hammer Mills . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H Dryers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . M
Cane Knives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . M Hoists Felt stretcher . . . . . . . . . . . . . . . . . . . . . . . . . . M
Car Dumpers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H Heavy duty . . . . . . . . . . . . . . . . . . . . . . . . . . . . H Felt whipper . . . . . . . . . . . . . . . . . . . . . . . . . . . H
Car Pullers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . M Medium duty . . . . . . . . . . . . . . . . . . . . . . . . . . . M Jordans . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H
Clarifiers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . U Skip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . M Log haul . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H
Classifiers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . M Laundry Washers Reversing . . . . . . . . . . . . . . . M Presses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . U
Clay Working Machinery Laundry Tumblers . . . . . . . . . . . . . . . . . . . . . . . . . . M Pulp machine reel . . . . . . . . . . . . . . . . . . . . . . M
Brick press . . . . . . . . . . . . . . . . . . . . . . . . . . . . H Line Shaft Stock chest . . . . . . . . . . . . . . . . . . . . . . . . . . . . M
Briquette machine . . . . . . . . . . . . . . . . . . . . . . . H Drive processing equipment . . . . . . . . . . . . . . . M Suction roll . . . . . . . . . . . . . . . . . . . . . . . . . . . . . U
Clay working machinery . . . . . . . . . . . . . . . . . . M Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . U Washers and thickeners . . . . . . . . . . . . . . . . . . M
Pug mill . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . M Other line shafts . . . . . . . . . . . . . . . . . . . . . . . . U Winders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . U
Compressors Lumber Industry Printing Presses . . . . . . . . . . . . . . . . . . . . . . . . . . . S
Centrifugal . . . . . . . . . . . . . . . . . . . . . . . . . . . . U Barkers hydraulic and mechanical . . . . . . . . S Pullers, Barge Haul . . . . . . . . . . . . . . . . . . . . . . . . . H
Lobe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . M Burner conveyor . . . . . . . . . . . . . . . . . . . . . . . . M Pumps
Reciprocating, multi-cylinder . . . . . . . . . . . . . . M Chain Saw and Drag Saw . . . . . . . . . . . . . . . . . . . . H Centrifugal . . . . . . . . . . . . . . . . . . . . . . . . . . . . U
Reciprocating, single-cylinder . . . . . . . . . . . . . . H Chain transfer . . . . . . . . . . . . . . . . . . . . . . . . . . H Proportioning . . . . . . . . . . . . . . . . . . . . . . . . . . M
Conveyors Uniformly Loaded or Fed Craneway transfer . . . . . . . . . . . . . . . . . . . . . . H Reciprocating
Apron . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . U De-barking drum . . . . . . . . . . . . . . . . . . . . . . . . H Single acting, 3 or more cylinders . . . . . . . M
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . U Edger feed . . . . . . . . . . . . . . . . . . . . . . . . . . . . H Double acting, 2 or more cylinders . . . . . . M
Belt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . U Gang feed . . . . . . . . . . . . . . . . . . . . . . . . . . . . M Rotary-gear type . . . . . . . . . . . . . . . . . . . . . . . . U
Bucket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . U Geen chain . . . . . . . . . . . . . . . . . . . . . . . . . . . . M Rubber and Plastics Industries
Chain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . U Live rolls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H Crackers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H Reducers
Flight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . U Log haul-lockline . . . . . . . . . . . . . . . . . . . . . . . . H Laboratory equipment . . . . . . . . . . . . . . . . . . . M
Classifications
Oven . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . U Log turning device . . . . . . . . . . . . . . . . . . . . . . H Mixing mills . . . . . . . . . . . . . . . . . . . . . . . . . . . . H
Screw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . U Main log conveyor . . . . . . . . . . . . . . . . . . . . . . H Refiners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . M
AGMA
Conveyors Heavy Duty, Not Uniformly Fed Off bearing rolls . . . . . . . . . . . . . . . . . . . . . . . . M Rubber calenders . . . . . . . . . . . . . . . . . . . . . . . M
Load
Apron . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . M Planer feed chains . . . . . . . . . . . . . . . . . . . . . . M Rubber mill (2 on line) . . . . . . . . . . . . . . . . . . . M
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . M Planer floor chains . . . . . . . . . . . . . . . . . . . . . . M Rubber mill (3 on line) . . . . . . . . . . . . . . . . . . . U
Belt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . M Planer tilting hoist . . . . . . . . . . . . . . . . . . . . . . . M Sheeter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . M
Bucket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . M Re-saw merry-go-round conveyor . . . . . . . . . . M Tire building machines . . . . . . . . . . . . . . . . . . . S
Chain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . M Roll cases . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H Tire and tube press openers . . . . . . . . . . . . . . . S
Flight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . M Slab conveyor . . . . . . . . . . . . . . . . . . . . . . . . . . H Tubers and strainers . . . . . . . . . . . . . . . . . . . . M
Live roll oven . . . . . . . . . . . . . . . . . . . . . . . . . . M Small waste-conveyor-belt . . . . . . . . . . . . . . . . U Warming mills . . . . . . . . . . . . . . . . . . . . . . . . . . M
Reciprocating . . . . . . . . . . . . . . . . . . . . . . . . . . H Small waste-conveyor-chain . . . . . . . . . . . . . . M Sand Muller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . M
Screw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . M Sorting table . . . . . . . . . . . . . . . . . . . . . . . . . . . M Screens
Shaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H Tipple hoist conveyor . . . . . . . . . . . . . . . . . . . . M Air washing . . . . . . . . . . . . . . . . . . . . . . . . . . . . U
Cranes (Except for Dry Dock Cranes) Tipple hoist drive . . . . . . . . . . . . . . . . . . . . . . . M Rotary, stone or gravel . . . . . . . . . . . . . . . . . . . M
Main hoists . . . . . . . . . . . . . . . . . . . . . . . . . . . . U Transfer conveyors . . . . . . . . . . . . . . . . . . . . . M Traveling water intake . . . . . . . . . . . . . . . . . . . U
Bridge travel . . . . . . . . . . . . . . . . . . . . . . . . . . . S Transfer rolls . . . . . . . . . . . . . . . . . . . . . . . . . . M Sewage Disposal Equipment
Trolley travel . . . . . . . . . . . . . . . . . . . . . . . . . . . S Tray drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . M Bar screens . . . . . . . . . . . . . . . . . . . . . . . . . . . U
Crusher Trimmer feed . . . . . . . . . . . . . . . . . . . . . . . . . . M Chemical fenders . . . . . . . . . . . . . . . . . . . . . . . U
Ore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H Waste conveyor . . . . . . . . . . . . . . . . . . . . . . . . M Collectors, circuline or straightline . . . . . . . . . . U
Stone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H Machine Tools Dewatering screens . . . . . . . . . . . . . . . . . . . . . M
Sugar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . M Bending roll . . . . . . . . . . . . . . . . . . . . . . . . . . . M Grit collectors . . . . . . . . . . . . . . . . . . . . . . . . . . U
Dredges Notching press, belt driven . . . . . . . . . . . . . . . . S Scum breakers . . . . . . . . . . . . . . . . . . . . . . . . . M
Cable reels . . . . . . . . . . . . . . . . . . . . . . . . . . . . M Plate planer . . . . . . . . . . . . . . . . . . . . . . . . . . . H Slow or rapid mixers . . . . . . . . . . . . . . . . . . . . . M
Conveyors . . . . . . . . . . . . . . . . . . . . . . . . . . . . M Punch press, gear driven . . . . . . . . . . . . . . . . . H Sludge collectors . . . . . . . . . . . . . . . . . . . . . . . U
Cutter head drives . . . . . . . . . . . . . . . . . . . . . . H Tapping machine . . . . . . . . . . . . . . . . . . . . . . . H Thickeners . . . . . . . . . . . . . . . . . . . . . . . . . . . . M
Jig drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H Other machine tools Vacuum filters . . . . . . . . . . . . . . . . . . . . . . . . . M
Maneuvering winches . . . . . . . . . . . . . . . . . . . M Main drives . . . . . . . . . . . . . . . . . . . . . . . . M Slab Pushers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . M
Pumps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . M Auxiliary drives . . . . . . . . . . . . . . . . . . . . . . U Steering Gear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . S
Screen drive . . . . . . . . . . . . . . . . . . . . . . . . . . . H Metal Mills Stokers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .U
Stackers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . M Draw bench carriage and main drive . . . . . . . . M Sugar Industry
Utility winches . . . . . . . . . . . . . . . . . . . . . . . . . M Forming machines . . . . . . . . . . . . . . . . . . . . . . H Cane knives . . . . . . . . . . . . . . . . . . . . . . . . . . . M
Dry Dock Cranes . . . . . . . . . . . . . . . . . . . . . . . . . . . S Pinch, dryer and scrubber rolls, reversing . . . . S Crushers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . M
Elevators Slitters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . M Mills . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H
Bucket, uniform load . . . . . . . . . . . . . . . . . . . . . U Table conveyors, nonreversing Textile Industry
Bucket, heavy load . . . . . . . . . . . . . . . . . . . . . . M Group drives . . . . . . . . . . . . . . . . . . . . . . . M Batchers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . M
Bucket, cont. . . . . . . . . . . . . . . . . . . . . . . . . . . . U Individual drives . . . . . . . . . . . . . . . . . . . . . H Calenders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . M
Centrifugal discharge . . . . . . . . . . . . . . . . . . . . U Table conveyors, reversing . . . . . . . . . . . . . . . . S Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . M
Escalators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . U Wire drawing and flattening machine . . . . . . . . M Dry cans . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . M
Freight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . M Wire winding machine . . . . . . . . . . . . . . . . . . . M Dryers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . M
Gravity discharge . . . . . . . . . . . . . . . . . . . . . . . U Mills, Rotary Type Dyeing machinery . . . . . . . . . . . . . . . . . . . . . . M
Man lifts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . S Ball . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . M Knitting machines . . . . . . . . . . . . . . . . . . . . . . . S
Passenger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . S Cement kilns . . . . . . . . . . . . . . . . . . . . . . . . . . M Looms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . M
Extruders (Plastics) Dryers and coolers . . . . . . . . . . . . . . . . . . . . . . M Mangles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . M
Blow molders . . . . . . . . . . . . . . . . . . . . . . . . . . M Kilns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . M Nappers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . M
Coating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . U Pebble . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . M Pads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . M
Film . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . U Rod, plain and wedge bar . . . . . . . . . . . . . . . . M Range drives . . . . . . . . . . . . . . . . . . . . . . . . . . . S
Pipe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . U Tumbling barrels . . . . . . . . . . . . . . . . . . . . . . . . H Slashers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . M
Pre-plasticizers . . . . . . . . . . . . . . . . . . . . . . . . . M Mixers Soapers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . M
Rods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . U Concrete mixers, cont. . . . . . . . . . . . . . . . . . . . M Spinners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . M
Sheet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . U Concrete mixers, intermittent . . . . . . . . . . . . . . M Tenter frames . . . . . . . . . . . . . . . . . . . . . . . . . . M
Tubing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . U Constant density . . . . . . . . . . . . . . . . . . . . . . . . U Washers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . M
Fans Variable density . . . . . . . . . . . . . . . . . . . . . . . . M Winders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . M
Centrifugal . . . . . . . . . . . . . . . . . . . . . . . . . . . . U Oil Industry Windlass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . S
Cooling towers . . . . . . . . . . . . . . . . . . . . . . . . . S Chillers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . M
Forced draft . . . . . . . . . . . . . . . . . . . . . . . . . . . S Oil well pumps . . . . . . . . . . . . . . . . . . . . . . . . . S U = Uniform Load H = Heavy Shock
Induced draft . . . . . . . . . . . . . . . . . . . . . . . . . . M Paraffin filter press . . . . . . . . . . . . . . . . . . . . . . M M = Moderate Shock S = Contact Sumitomo
Large (mine, etc.) . . . . . . . . . . . . . . . . . . . . . . . M Rotary kilns . . . . . . . . . . . . . . . . . . . . . . . . . . . M
B-3
Reducers
Reducer Selection Flowchart
DETERMINE TYPE OF DRIVEN MACHINE
CHECK HOURS OF OPERATION
CHOOSE A LOAD CLASSIFICATION See Load Classification Table, Page B-3

See Service Factor Table, Page B-2
CALCULATE SELECTION HORSEPOWER
DETERMINE INPUT AND OUTPUT SPEEDS See Reducer Selection Tables, Pages B-6 ~ B-21
MAKE A PRELIMINARY SELECTION

Reducers
Flowchart
Selection
DIRECT NO
CONNECT DETERMINE OVERHUNG LOAD
OUTPUT
YES YES OHL<

OHL IN
TABLES
SELECT MOUNTING STYLE
NO
LARGER UNIT OR DECREASE OHL
CHECK OPERATING ENVIRONMENT See Standard Specifications, Page B-2
FINALIZE REQUIRED OPTIONS
Hyponic
B-4
Reducers
Reducer Selection Procedure

The following information is required to properly select a Hyponic® Reducer
1. Application Type of Driven Machine Example: Belt Conveyor Uniformly Fed

2. Hours of Operation per Day 10 Hours of Operation per Day
3. Motor Power and Speed 2 HP Motor, 1750 RPM 145TC
4. Desired Output Speed 37 RPM
5. Mounting Position and Style Horizontal, Foot Mounted
6. Environmental Conditions Inside Industrial Plant
7. Required Options C Face Adapter
8. Electrical Specifications 460 Volts, 60 Hertz, 3 phase
9. Overhung or Thrust Loads None Direct Coupled Output
10. Shaft Dimensions Inch or Metric Inch Shafting
Review the Basic Information and Recommendations on pages 4 and 5, then proceed to Selection Example 1.
Selection Example 1
Step 1
Using the information above, choose a Load Classification in the Application Table (page B-3): Conveyors Uniformly
Loaded or Fed = U. Determine the service factor from the Service Factor Table (page B-2): Electric motor prime
mover, operating 10 hours per day, with uniform loading = 1.00 service factor.
Step 2
Multiply either the motor horsepower or demand horsepower by the service factor:
2 motor horsepower X 1.00 service factor = 2.0 selection horsepower
Step 3 Reducers
Go to the Reducer Selection Table (pages B-6 ~ 21)for the correct input speed. Find the ratio providing the output
speed closest to the desired speed. At 1750 RPM, the closest speed to 37 RPM is 35 RPM. The ratio for this speed
Procedure
Selection
is 50:1. Go down the column to a selection equal to or next closest to the selection horsepower of 2 HP. The 2.07 HP
rating for frame size 1520, having a ratio of 50:1, exceeds 2 HP.
Are there any overhung or thrust loads? For shaft mounted or direct connected units, proceed to Step 4. Otherwise,
any overhung or thrust loads must be checked against the capability of the selection.
To check overhung load use this formula: HP: Transmitted or Motor HP

Cf: Load Connection Factor
Overhung = 126,000 x HP x Cf x Lf x Fs Lf: Load Location Factor
Load (OHL) DxN D: Pitch Diameter (in)
N: Shaft RPM
Fs: Shock factor
The specific values for the overhung load factors, as well as a method to evaluate thrust loads, are listed on page D-5
in the Technical Information Section.
Step 4
Select the desired mounting position and housing style from the nomenclature on page 2. The shaft mounted
designation is RNY. The unit nomenclature is RNYJ-1520Y- 50.
Step 5
Check environmental conditions against the Standard Specifications on page B-2: inside industrial plant. No
environmental modifications required.
Step 6
Specify desired specifications and options: 145TC motor adapter, 1-1/2 hollow bore.
Hyponic
B-5
Reducers
Reducer Selection Tables

1750 RPM Input Speed
Frame Output RPM 350 250 175 146 117 87.5 70 58.3 43.8
Size Nominal Ratio 5 7 10 12 15 20 25 30 40
Input HP 0.268 0.268 0.268 0.268 0.268 0.268 0.268 0.268 0.134
1120 Output Torque inlbs 41.1 57.5 82.1 98.5 123 164 205 246 164
Hollow Bore OHL lbs 132 143 165 176 187 210 220 232 254
Input HP
1230 Output Torque inlbs
Hollow Bore OHL lbs
Input HP 0.536 0.536 0.536 0.536 0.536 0.536 0.536 0.536 0.268
1220 Output Torque inlbs 82.1 115 164 197 246 328 411 493 328
Input HP
Hollow Bore OHL lbs
Input HP 1.07 1.07 1.07 1.07 1.07 1.07 1.07 1.07 0.54
1320 Output Torque inlbs 165 230 329 395 493 658 822 982 658
Input HP
Reducers
Hollow Bore OHL lbs
Input HP 2.07 2.07 2.07 2.07 2.07 2.07 2.07 2.07 1.07
Selection
Tables
Input HP
Hollow Bore OHL lbs
Input HP 3.00 3.00 3.00 3.00 3.00 3.00 3.00 3.00 2.07
Input HP 3.00
1531 Output Torque inlbs 3669
Hollow Bore OHL lbs 1245
Hyponic
B-6
Reducers
1750 RPM Input Speed (cont.)

35.0 29.2 21.9 17.5 14.6 11.7 8.75 7.29 Output RPM Frame Dimension
50 60 80 100 120 150 200 240 Nominal Ratio Size Page
0.134 0.134 Input HP
205 246 Output Torque inlbs 1120 B-22
277 285 Hollow Bore OHL lbs
0.134 0.134 0.134 0.134 0.134 0.118 Input HP
328 411 493 616 821 867 Output Torque inlbs 1230 B-23
398 398 407 407 407 407 Hollow Bore OHL lbs
0.268 0.268 Input HP
0.268 0.268 0.268 0.268 0.268 0.235 Input HP
0.54 0.54 Input HP
0.536 0.536 0.536 0.536 0.536 0.469 Input HP
Reducers
1.07 1.07 Input HP
Selection
Tables
1.07 1.07 1.07 1.07 1.06 0.880 Input HP
2.07 2.07 Input HP
3.00 3.00 2.07 Input HP
4592 5504 5057 Output Torque inlbs 1531 B-23
1310 1355 1378 Hollow Bore OHL lbs
Hyponic
B-7
Reducers

Frame Output RPM 290 207 145 121 96.7 72.5 58.0 48.3 36.3
Input HP 0.268 0.268 0.268 0.268 0.268 0.268 0.268 0.268 0.134
1120 Output Torque inlbs 49.5 69.4 99.1 119 149 198 248 297 198
Input HP
Hollow Bore OHL lbs
Input HP 0.536 0.536 0.536 0.536 0.536 0.536 0.536 0.536 0.268
1220 Output Torque inlbs 99.1 139 198 238 297 396 495 595 396
Input HP
Hollow Bore OHL lbs
Input HP 1.07 1.07 1.07 1.07 1.07 1.07 1.07 1.07 0.54
Input HP
Reducers
Hollow Bore OHL lbs
Input HP 2.07 2.07 2.07 2.07 2.07 2.07 2.07 2.07 1.07
Selection
Tables
Input HP
Hollow Bore OHL lbs
Input HP 2.95 2.95 2.95 2.95 2.95 2.95 2.95 2.95 2.07
Input HP 2.95
Hyponic
B-8
Reducers

0.134 0.134 Input HP
0.134 0.134 0.134 0.134 0.117 0.098 Input HP
0.268 0.268 Input HP
0.268 0.268 0.268 0.268 0.233 0.194 Input HP
0.536 0.536 Input HP
0.536 0.536 0.536 0.536 0.467 0.389 Input HP
Reducers
1.07 1.07 Input HP
Selection
Tables
1.07 1.07 1.07 1.07 0.876 0.730 Input HP
2.07 2.07 Input HP
2.95 2.95 2.07 Input HP
Hyponic
B-9
Reducers

Frame Output RPM 233 166 117 97.1 77.7 58.3 46.6 38.8 29.1
Input HP 0.216 0.216 0.216 0.216 0.216 0.216 0.216 0.216 0.107
1120 Output Torque inlbs 49.6 69.5 99.3 119.1 148.9 198.6 248.2 297.8 197.3
Input HP
Hollow Bore OHL lbs
Input HP 0.430 0.430 0.430 0.430 0.430 0.430 0.430 0.430 0.216
Input HP
Hollow Bore OHL lbs
Input HP 0.862 0.862 0.862 0.862 0.862 0.862 0.862 0.862 0.430
Input HP
Reducers
Hollow Bore OHL lbs
Input HP 1.66 1.66 1.66 1.66 1.66 1.66 1.66 1.66 0.862
Selection
Tables
Input HP
Hollow Bore OHL lbs
Input HP 2.37 2.37 2.37 2.37 2.37 2.36 2.37 2.37 1.66
Input HP 2.37
Hyponic
B-10
Reducers

0.107 0.107 Input HP
246.7 296.0 Output Torque inlbs 1120 B-22
0.107 0.107 0.107 0.107 0.094 0.079 Input HP
0.216 0.216 Input HP
0.216 0.216 0.216 0.216 0.188 0.157 Input HP
0.430 0.430 Input HP
0.430 0.430 0.430 0.430 0.375 0.312 Input HP
Reducers
0.862 0.862 Input HP
Selection
Tables
0.862 0.862 0.862 0.862 0.703 0.586 Input HP
1.66 1.66 Input HP
2.37 2.37 1.66 Input HP
Hyponic
B-11
Reducers

980 RPM Input Speed
Frame Output RPM 196 140 98.0 81.7 65.3 49.0 39.2 32.7 24.5
Input HP 0.181 0.181 0.181 0.181 0.181 0.181 0.181 0.181 0.091
Input HP
Hollow Bore OHL lbs
Input HP 0.362 0.362 0.362 0.362 0.362 0.362 0.362 0.362 0.181
Input HP
Hollow Bore OHL lbs
Input HP 0.725 0.725 0.725 0.725 0.725 0.725 0.725 0.725 0.362
Input HP
Reducers
Hollow Bore OHL lbs
Input HP 1.40 1.40 1.40 1.40 1.40 1.40 1.40 1.40 0.725
Selection
Tables
Input HP
Hollow Bore OHL lbs
Input HP 2.00 2.00 2.00 2.00 2.00 2.00 2.00 2.00 1.40
Input HP 2.00
Hyponic
B-12
Reducers

0.091 0.091 Input HP
0.091 0.091 0.091 0.091 0.079 0.066 Input HP
0.181 0.181 Input HP
0.181 0.181 0.181 0.181 0.158 0.131 Input HP
0.362 0.362 Input HP
0.362 0.362 0.362 0.362 0.315 0.263 Input HP
Reducers
0.725 0.725 Input HP
Selection
Tables
0.725 0.725 0.725 0.725 0.591 0.493 Input HP
1.40 1.40 Input HP
2.00 2.00 1.40 Input HP
Hyponic
B-13
Reducers

870 RPM Input Speed
Frame Output RPM 174 124 87.0 72.5 58.0 43.5 34.8 29.0 21.8
Input HP 0.161 0.161 0.161 0.161 0.161 0.161 0.161 0.161 0.080
Input HP
Hollow Bore OHL lbs
Input HP 0.322 0.322 0.322 0.322 0.322 0.322 0.322 0.322 0.161
Input HP
Hollow Bore OHL lbs
Input HP 0.644 0.644 0.644 0.644 0.644 0.644 0.644 0.644 0.322
Input HP
Reducers
Hollow Bore OHL lbs
Input HP 1.24 1.24 1.24 1.24 1.24 1.24 1.24 1.24 0.644
Selection
Tables
Input HP
Hollow Bore OHL lbs
Input HP 1.77 1.77 1.77 1.77 1.77 1.77 1.77 1.77 1.24
Input HP 1.77
Hyponic
B-14
Reducers

0.080 0.080 Input HP
0.080 0.080 0.080 0.080 0.070 0.059 Input HP
0.161 0.161 Input HP
0.161 0.161 0.161 0.161 0.139 0.117 Input HP
0.322 0.322 Input HP
0.322 0.322 0.322 0.322 0.280 0.233 Input HP
Reducers
0.644 0.644 Input HP
Selection
Tables
0.644 0.644 0.644 0.644 0.526 0.437 Input HP
1.24 1.24 Input HP
1.77 1.77 1.24 Input HP
Hyponic
B-15
Reducers

720 RPM Input Speed
Frame Output RPM 144 103 72.0 60.0 48.0 36.0 28.8 24.0 18.0
Input HP 0.133 0.133 0.133 0.133 0.133 0.133 0.133 0.133 0.067
Input HP
Hollow Bore OHL lbs
Input HP 0.267 0.267 0.267 0.267 0.267 0.267 0.267 0.267 0.133
Input HP
Hollow Bore OHL lbs
Input HP 0.532 0.532 0.532 0.532 0.532 0.532 0.532 0.532 0.267
Input HP
Reducers
Hollow Bore OHL lbs
Input HP 1.03 1.03 1.03 1.03 1.03 1.03 1.03 1.03 0.532
Selection
Tables
Input HP
Hollow Bore OHL lbs
Input HP 1.46 1.46 1.46 1.46 1.46 1.46 1.46 1.46 1.03
Input HP 1.46
Hyponic
B-16
Reducers

0.067 0.067 Input HP
0.067 0.067 0.067 0.067 0.058 0.048 Input HP
0.133 0.133 Input HP
0.133 0.133 0.133 0.133 0.115 0.097 Input HP
0.267 0.267 Input HP
0.267 0.267 0.267 0.267 0.232 0.193 Input HP
Reducers
0.532 0.532 Input HP
Selection
Tables
0.532 0.532 0.532 0.532 0.434 0.362 Input HP
1.03 1.03 Input HP
1.46 1.46 1.03 Input HP
Hyponic
B-17
Reducers

580 RPM Input Speed
Frame Output RPM 116 82.9 58.0 48.3 38.7 29.0 23.2 19.3 14.5
Input HP 0.107 0.107 0.107 0.107 0.107 0.107 0.107 0.107 0.054
Input HP
Hollow Bore OHL lbs
Input HP 0.215 0.215 0.215 0.215 0.215 0.215 0.215 0.215 0.107
Input HP
Hollow Bore OHL lbs
Input HP 0.429 0.429 0.429 0.429 0.429 0.429 0.429 0.429 0.215
Input HP
Reducers
Hollow Bore OHL lbs
Input HP 0.826 0.826 0.826 0.826 0.826 0.826 0.826 0.826 0.429
Selection
Tables
Input HP
Hollow Bore OHL lbs
Input HP 1.18 1.18 1.18 1.18 1.18 1.18 1.18 1.18 0.826
Input HP 1.18
Hyponic
B-18
Reducers

0.054 0.054 Input HP
0.054 0.054 0.054 0.054 0.047 0.039 Input HP
0.107 0.107 Input HP
0.107 0.107 0.107 0.107 0.067 0.078 Input HP
0.215 0.215 Input HP
0.215 0.215 0.215 0.215 0.186 0.156 Input HP
Reducers
0.429 0.429 Input HP
Selection
Tables
0.429 0.429 0.429 0.429 0.350 0.292 Input HP
0.826 0.826 Input HP
1.18 1.18 0.826 Input HP
Hyponic
B-19
Reducers

50 RPM Input Speed
Frame Output RPM 10.0 7.14 5.00 4.17 3.33 2.50 2.00 1.67 1.25
Input HP 0.009 0.009 0.009 0.009 0.009 0.009 0.009 0.009 0.004
Input HP
Hollow Bore OHL lbs
Input HP 0.018 0.018 0.018 0.018 0.018 0.018 0.018 0.018 0.009
Input HP
Hollow Bore OHL lbs
Input HP 0.037 0.037 0.037 0.037 0.037 0.037 0.037 0.037 0.018
Input HP
Reducers
Hollow Bore OHL lbs
Input HP 0.07 0.07 0.07 0.07 0.07 0.07 0.07 0.07 0.04
Selection
Tables
Input HP
Hollow Bore OHL lbs
Input HP 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.07 0.07
Input HP 0.07
Hyponic
B-20
Reducers

0.004 0.004 Input HP
0.005 0.005 0.005 0.005 0.004 0.003 Input HP
0.009 0.009 Input HP
0.009 0.009 0.009 0.009 0.008 0.007 Input HP
0.018 0.018 Input HP
0.018 0.018 0.018 0.018 0.016 0.013 Input HP
Reducers
0.04 0.04 Input HP
Selection
Tables
0.037 0.037 0.037 0.037 0.030 0.025 Input HP
0.07 0.07 Input HP
0.07 0.07 0.05 Input HP
Hyponic
B-21
Reducers
Hollow Shaft Type, C-Face

RNYJ-1120/1220/1320/1420/1520Y
CE
C XJ
D D L N B Z C
P P A BB
AJ
XV
L K ZA
B B BD
DIA DIA R MIN
A I.D. AK
J E
4X H DIA A B
F G F
K E C
A X C-C
O (ADAPTER ONLY)
S 4X BF DIA HOLE
M DIA
T DIA U DIA BORE KEY
W W XU
V
B-B
A-A
Reducers
Inch
Dimensions

RNYJ-1120Y 3.54 2.046 2.047 1.30 1.65 0.31 2.60 0.26 1.97 1.26 1.57 3.23 0.24 0.79 0.87
RNYJ-1220Y 4.53 3.070 3.071 1.46 2.24 0.35 2.91 0.35 2.60 1.57 1.93 3.78 0.20 1.10 0.79
RNYJ-1320Y 5.20 3.345 3.346 1.81 2.44 0.35 3.62 0.43 2.91 1.81 2.28 4.69 0.20 1.08 1.34
RNYJ-1420Y 6.22 3.739 3.740 2.32 2.95 0.39 4.65 0.55 3.46 2.24 2.76 5.75 0.20 0.79 1.69
RNYJ-1520Y 7.01 4.329 4.331 2.68 3.15 0.39 5.35 0.55 3.70 2.76 3.31 7.01 0.20 1.10 2.68
Output Shaft Input Shaft

Model
U min U max V KEY M O S T W XU min XU max XV KEY
RNYJ-1120Y 0.750 0.751 3.23 3/16X3/16 0.77 0.59 0.039 0.796 1.22 0.4996 0.5000 0.98 1/8X1/8X0.71
RNYJ-1220Y 1.000 1.001 3.62 1/4X1/4 1.02 0.87 0.046 1.066 1.50 0.4996 0.5000 0.98 1/8X1/8X0.71
RNYJ-1320Y 1.250 1.252 4.33 1/4X1/4 1.27 0.87 0.056 1.330 1.81 0.6246 0.6250 0.98 3/16X3/16X0.75
RNYJ-1420Y 1.375 1.377 5.43 5/16X5/16 1.40 1.02 0.056 1.461 2.05 0.6246 0.6250 0.98 3/16X3/16X0.75
RNYJ-1520Y 1.500 1.502 6.14 3/8X3/8 1.52 1.02 0.056 1.594 2.28 0.7495 0.7500 1.38 3/16X3/16X1.02
NEMA MIN WT
Model Ratio CE C XJ AK BD AJ BF Z BB ZA
FRAME I.D. (LB)
RNYJ-1120Y 5~60 42C 10.72 8.94 1.78 3.0 4.33 3.75 0.28 0.47 - 2.44 - 12
RNYJ-1120Y 5~60 48C 11.09 8.94 2.16 3.0 4.33 3.75 0.28 0.47 - 2.44 - 13
RNYJ-1220Y 40~60 48C 12.39 10.24 2.16 3.0 4.33 3.75 0.28 0.47 - 2.44 - 16
RNYJ-1220Y 5~30 56C 12.80 10.24 2.56 4.5 6.69 5.87 0.43 0.47 - 3.15 - 17
RNYJ-1320Y 40~60 56C 14.52 11.89 2.63 4.5 6.69 5.87 0.43 0.47 - 4.21 4.53 29
RNYJ-1320Y 5~30 143TC 14.52 11.89 2.63 4.5 6.69 5.87 0.43 0.47 - 4.21 4.53 29
RNYJ-1420Y 40~60 143TC 15.93 13.31 2.63 4.5 6.69 5.87 0.43 0.47 - 4.21 4.53 36
RNYJ-1420Y 5~30 143TC 16.29 13.66 2.63 4.5 6.69 5.87 0.43 0.47 - 4.21 4.53 36
RNYJ-1520Y 40~60 143TC 19.20 16.57 2.63 4.5 6.69 5.87 0.43 0.47 - 4.21 5.12 67
RNYJ-1520Y 5~30 184TC 19.94 16.57 3.37 8.5 8.98 7.25 0.55 0.47 0.22 5.43 5.12 71
Hyponic
B-22
Reducers
RNYJ-1230/1330/14301530/1531Y
CE
C XJ
D D L N B Z
P P C
A BB AJ
XV
L K ZA
B B BD
DIA DIA MIN
A I.D.
AK
J E
I DIA B
Q
A C
4X H DIA K E 4X BF DIA HOLE
F G F C-C
A X
O (ADAPTER ONLY)
S M DIA
T DIA U DIA BORE KEY
XU
W W
V B-B
A-A
Reducers
Inch
Dimensions
RNYJ-1230Y 5.00 3.070 3.071 1.61 2.56 0.35 3.23 0.35 0.55 2.99 1.57 2.01 3.74 0.20 2.87 0.51 0.31
RNYJ-1330Y 5.98 3.345 3.346 1.81 3.11 0.35 3.62 0.43 0.69 3.62 1.85 2.36 4.25 0.20 3.19 0.43 0.14
RNYJ-1430Y 7.01 3.739 3.740 2.32 3.62 0.39 4.65 0.55 0.79 4.25 2.13 2.76 5.12 0.20 4.13 0.55 0.31
RNYJ-1530Y 8.39 4.329 4.331 2.68 4.29 0.39 5.35 0.71 - 5.08 2.52 3.31 6.18 0.20 - 0.67 0.37
RNYJ-1531Y 8.39 4.329 4.331 2.68 4.29 0.39 5.35 0.71 - 5.08 2.52 3.31 6.18 0.20 - 0.67 0.37
Output Shaft Input Shaft

Model
U min U max V KEY M O S T W XU min XU max XV KEY
RNYJ-1230Y 1.000 1.001 3.94 1/4X1/4 1.02 0.87 0.046 1.066 1.50 0.4996 0.500 0.98 1/8X1/8X0.71
RNYJ-1330Y 1.250 1.252 4.33 1/4X1/4 1.27 0.87 0.056 1.330 1.81 0.4996 0.500 0.98 1/8X1/8X0.71
RNYJ-1430Y 1.375 1.377 5.43 5/16X5/16 1.40 1.02 0.056 1.461 2.05 0.6246 0.625 0.98 3/16X3/16X0.75
RNYJ-1530Y 1.500 1.502 6.14 3/8X3/8 1.52 1.02 0.056 1.594 2.28 0.6246 0.625 0.98 3/16X3/16X0.75
RNYJ-1531Y 1.500 1.502 6.14 3/8X3/8 1.52 1.02 0.056 1.594 2.28 0.7495 0.750 1.38 3/16X3/16X1.02
NEMA MIN WT
Model Ratio CE C XJ AK BD AJ BF Z BB ZA
FRAME I.D. (LB)
RNYJ-1230Y 80~240 42C 11.66 9.88 1.78 3.0 4.33 3.75 0.28 0.47 - 2.44 - 16
RNYJ-1330Y 80~240 48C 13.30 11.14 2.16 3.0 4.33 3.75 0.28 0.47 - 2.44 - 20
RNYJ-1430Y 80~120 56C 15.42 12.80 2.63 4.5 6.69 5.87 0.43 0.47 - 4.21 4.53 38
RNYJ-1430Y 150~240 56C 15.46 12.83 2.63 4.5 6.69 5.87 0.43 0.47 - 4.21 4.53 38
RNYJ-1530Y 80~120 143TC 16.92 14.29 2.63 4.5 6.69 5.87 0.43 0.47 - 4.21 4.53 51
RNYJ-1530Y 150~240 143TC 17.19 14.57 2.63 4.5 6.69 5.87 0.43 0.47 - 4.21 4.53 51
RNYJ-1531Y 80 143TC 17.90 15.28 2.63 4.5 6.69 5.87 0.43 0.47 - 4.21 5.12 63
RNYJ-1531Y 40~60 183TC 18.65 15.28 3.37 8.5 8.98 7.25 0.55 0.47 0.22 5.43 5.12 66
Hyponic
B-23
Reducers
Notes
Reducers
Hyponic
B-24
Options
C
Options
Options
Options
Hyponic
C-1
Options
Plug-In Solid Output Shaft
A plug-in output shaft converts the

hollow output to a solid output
reducer.
Plug-in Solid Output Shaft, Casing Surface Mount With Safety Cover
Dimensions (Inch)
Options
Output Shaft
Options
Model B min B max D P M W

U min U max V F S Key
RNFM-1120Y 2.0460
2.046 2.3622
2.047 1.30 0.12 2.20 0.79 0.7495 0.7500 1.10 1.97 #10-32 UNF x 0.63 3/16 x 3/16
RNFM-1220Y 3.070
3.3451 3.071
3.3465 1.46 0.12 2.32 1.26 0.9995 1.0000 1.42 2.50 5/16-18UNC x 0.63 1/4 x 1/4
RNFM-1320Y 3.345
3.6994 3.346
3.7008 1.81 0.12 2.64 1.26 1.2494 1.2500 1.65 2.80 5/16-18UNC x 0.63 1/4 x 1/4
RNFM-1420Y 3.739
4.1325 3.740
4.1339 2.32 0.12 3.03 1.65 1.3744 1.3750 2.28 3.58 5/16-18UNC x 0.63 5/16 x 5/16
RNFM-1520Y 4.329
4.7230 4.331
4.7244 2.68 0.12 3.54 1.65 1.7494 1.7500 3.23 4.72 3/8-16UNC x 0.71 3/8 x 3/8
RNFM-1230Y 3.070
3.3451 3.071
3.3465 1.65 0.12 2.32 1.26 0.9995 1.0000 1.42 2.50 5/16-18UNC x 0.63 1/4 x 1/4
RNFM-1330Y 3.345
3.6994 3.346
3.7008 1.81 0.12 2.64 1.26 1.2494 1.2500 1.65 2.80 5/16-18UNC x 0.63 1/4 x 1/4
RNFM-1430Y 3.739
4.1325 3.740
4.1339 2.32 0.12 3.03 1.65 1.3744 1.3750 2.28 3.58 5/16-18UNC x 0.63 5/16 x 5/16
RNFM-1530Y 4.329
4.7230 4.331
4.7244 2.68 0.12 3.54 1.65 1.7494 1.7500 3.23 4.72 3/8-16UNC x 0.71 3/8 x 3/8
RNFM-1531Y 4.329
4.7230 4.331
4.7244 2.68 0.12 3.54 1.65 1.7494 1.7500 3.23 4.72 3/8-16UNC x 0.71 3/8 x 3/8
Hyponic
C-2
Options
Plug-In Solid Output Shaft Foot Mounted
A bolt-on adaptor converts the solid

output reducer to a foot mounted
reducer
Plug-in Solid Shaft, Bolt-on Foot Mount With Safety Cover
Dimensions (Inch)
D C
V N
KEY
F
M
DIA U DIA
S
E
B A B G H 4X K DIA
P K J K
Options
Options
Output Shaft
Model A B C D E F G H J K M N
U min U max V S Key
RNHM-1120Y 4.72 0.39 3.27 2.60 3.54 1.57 0.39 1.18 2.76 0.35 2.20 1.57 0.7495 0.7500 1.10 #10-32UNF x 0.63 3/16 x 3/16
RNHM-1220Y 5.35 0.59 3.96 2.72 4.33 2.01 0.39 1.57 4.13 0.35 2.32 2.01 0.9995 1.0000 1.42 5/16-18UNC x 0.63 1/4 x 1/4
RNHM-1320Y 6.46 0.59 4.61 3.07 4.41 2.36 0.47 1.85 4.96 0.43 2.64 2.36 1.2494 1.2500 1.65 5/16-18UNC x 0.63 1/4 x 1/4
RNHM-1420Y 8.03 0.79 5.91 3.98 5.20 2.76 0.47 2.01 5.51 0.55 3.03 2.76 1.3744 1.3750 2.28 5/16-18UNC x 0.63 5/16 x 5/16
RNHM-1520Y 9.61 0.79 7.40 4.33 6.30 3.31 0.59 2.52 6.81 0.71 3.54 3.31 1.7494 1.7500 3.23 3/8-16UNC x 0.71 3/8 x 3/8
RNHM-1230Y 5.67 0.59 4.11 2.87 4.33 2.01 0.39 1.57 4.13 0.35 2.32 2.01 0.9995 1.0000 1.42 5/16-18UNC x 0.63 1/4 x 1/4
RNHM-1330Y 6.46 0.59 4.61 3.07 4.41 2.36 0.47 1.85 4.96 0.43 2.64 2.36 1.2494 1.2500 1.65 5/16-18UNC x 0.63 1/4 x 1/4
RNHM-1430Y 8.03 0.79 5.91 3.98 5.20 2.76 0.47 2.01 5.51 0.55 3.03 2.76 1.3744 1.3750 2.28 5/16-18UNC x 0.63 5/16 x 5/16
RNHM-1530Y 9.61 0.79 7.40 4.33 6.30 3.31 0.59 2.52 6.81 0.71 3.54 3.31 1.7494 1.7500 3.23 3/8-16UNC x 0.71 3/8 x 3/8
RNHM-1531Y 9.61 0.79 7.40 4.33 6.30 3.31 0.59 2.52 6.81 0.71 3.54 3.31 1.7494 1.7500 3.23 3/8-16UNC x 0.71 3/8 x 3/8
Hyponic
C-3
Options
Output Flange
Flange adaptors provide additional

motor clearance when the application
requires a flush or face mount.
Hollow Shaft, Bolt-on Flange Mount
Plug-in Solid Shaft, Bolt-on Flange Mount With Safety Cover
D F
W P
V
Dimensions (Inch) KEY
M U DIA B
DIA DIA
Options
Options
Output Shaft
Model B min B max D P M W
U min U max V F S Key
RNFM-1120Y 2.3610 2.3622 2.50 0.12 2.20 0.79 0.7495 0.7500 1.10 1.30 #10-32 UNF x 0.63 3/16 x 3/16
RNFM-1220Y 3.3455 3.3465 3.25 0.12 2.32 1.26 0.9995 1.0000 1.42 1.61 5/16-18UNC x 0.63 1/4 x 1/4
RNFM-1320Y 3.6998 3.7008 3.48 0.12 2.64 1.26 1.2494 1.2500 1.65 1.85 5/16-18UNC x 0.63 1/4 x 1/4
RNFM-1420Y 4.1327 4.1339 3.74 0.12 3.03 1.65 1.3744 1.3750 2.28 2.48 5/16-18UNC x 0.63 5/16 x 5/16
RNFM-1520Y 4.7232 4.7244 3.74 0.12 3.54 1.65 1.7494 1.7500 3.23 3.43 3/8-16UNC x 0.71 3/8 x 3/8
RNFM-1230Y 3.3455 3.3465 2.50 0.12 2.24 1.26 0.9995 1.0000 1.42 1.61 5/16-18UNC x 0.63 1/4 x 1/4
RNFM-1330Y 3.6998 3.7008 2.50 0.12 2.64 1.26 1.2494 1.2500 1.65 1.85 5/16-18UNC x 0.63 1/4 x 1/4
RNFM-1430Y 4.1327 4.1339 3.25 0.12 3.03 1.65 1.3744 1.3750 2.28 2.48 5/16-18UNC x 0.63 5/16 x 5/16
RNFM-1530Y 4.7232 4.7244 3.74 0.12 3.54 1.65 1.7494 1.7500 3.23 3.43 3/8-16UNC x 0.71 3/8 x 3/8
RNFM-1531Y 4.7232 4.7244 3.74 0.12 3.54 1.65 1.7494 1.7500 3.23 3.43 3/8-16UNC x 0.71 3/8 x 3/8
Hyponic
C-4
Technical Information
D
Technical
Information
Hyponic
D-1
Shaft Dimensions
Table D-1. Hollow Shaft Dimensions (In.) Table D-2. Hollow Shaft Optional Metric Bore
[1] Dimensions (mm)
Frame Size
Bore 1320 1420 1520 60 Frame Size [1]
Size 1220
1120 1330 1430 1530 63 Bore 1520
(In.) 1230 1320 60
361 461 1531 64 Size 1220 1430 1530
56 (inch) 1120 1330 1420 63
1230 461 1531
361 64
5/8 56
20
3/4
25
13/16
30
7/8
35
15/16
38
1
40
1-1/8
45
1-3/16
50
1-1/4
55
1-5/16
1-3/8
1-7/16
[2] Table D-3. Solid Shaft Dimensions (In.)
Frame Size [1]
1-1/2 Bore
Size 1220 1320 1420 1520
1-5/8 (inch) 1120 1230 1330 1430 1530
1531
1-11/16
5/8
1-3/4
3/4
1-7/8
1
1-15/16
1-1/4
2
Technical
Information 1-5/16
2-1/16
Dimensions
1-3/8
2-1/8
Shaft
1-7/16
2-3/16
[3]
1-1/2
Notes: [1] Standard, Semi-standard. Contact factory for
price and delivery.
[2] Only for frame sizes 1430 and 461. 1-3/4
[3] Standard shaft dimension for T-type.
2
Hyponic
D-2
Shaft Rotation
Table D-4. Shaft Rotation Direction
Frame Frame
Size Reduction Ratio (:1) Size Reduction Ratio (:1)
361 300, 360, 480, 560, 750, 900, 1200, 1440 361
461 300, 360, 480, 560, 750, 900, 1200, 1440 461
56 300, 360, 480, 560, 750, 900, 1200, 1440 56
60 60 80, 100, 120
63 10, 12, 15, 20, 25, 30 63 40, 50
64 10, 12, 15, 20, 25 64 30, 40
1120 5, 7, 10, 12, 15, 20, 25, 30, 40, 50, 60 1120
1220 5, 7, 10, 12, 15, 20, 25, 30, 40, 50, 60 1220
1230 1230 80, 100, 120, 150, 200, 240
1320 5, 7, 10, 12, 15, 20, 25, 30, 40, 50, 60 1320
1330 1330 80, 100, 120, 150, 200, 240
1420 5, 7, 10, 12, 15, 20, 25, 30, 40, 50, 60 1420
1430 1430 80, 100, 120, 150, 200, 240
1520 5, 7, 10, 12, 15, 20, 25, 30, 40, 50, 60 1520
1530 1530 80, 100, 120, 150, 200, 240
1531 1531 40, 50, 60, 80
Fig. D-1 Fig. D-2
CCW CW
Technical
Information
CW CW
Shaft Rotation
Hyponic
D-3
Actual Reduction Ratio

Table D-5. Actual Reduction Ratio
Nominal Reduction Ratio (:1)
Frame
Size 5 7 10 12 15 20 25 30 40 50 60 80 100
1120 5.00 7.03 9.81 11.74 15.26 20.67 24.62 30.00 41.33 49.23 60.00
1220 5.00 7.03 9.81 11.74 15.26 20.67 24.62 30.00 41.33 49.23 60.00
1320 5.00 7.03 9.81 11.74 15.26 20.67 24.62 30.00 41.33 49.23 60.00
1420 5.00 6.97 10.00 11.96 14.75 19.69 25.00 30.45 39.38 50.00 60.91
1520 5.00 7.03 9.81 11.74 15.26 20.67 24.62 30.00 41.33 49.23 60.00
1230 81.45 101.01
1330 81.94 102.27
1430 80.37 102.35
1530 79.63 101.32
1531 39.20 49.88 57.60 77.42
60 80.50 102.94
63 10.31 12.47 14.48 20.39 24.15 29.24 41.16 49.00
64 10.34 12.40 14.57 20.88 24.33 29.40 40.25
Nominal Reduction Ratio (:1)

Frame
Size 120 150 200 240 300 360 480 560 750 900 1200 1440
1120
1220
1320
1420
1520
Technical
Information
1230 120.15 151.51 200.39 231.27
Reduction
1330 122.54 153.40 199.13 232.50

Ratio
1430 122.64 153.52 199.29 240.00
1530 119.17 151.99 191.52 232.25
1531
60 119.00
63
64
361 306.80 367.60 465.00 564.51 732.78 855.60 1239.00 1484.60
461 307.05 367.91 480.00 564.97 733.37 883.20 1240.00 1485.80
56 300.74 353.70 459.55 557.28 702.23 851.58 1149.11 1393.49
Hyponic
D-4
Allowable Overhung Load

Overhung Load Acting on the Slow Speed Shaft
The existing overhung load acting on the output shaft must not exceed the allowable unit rating.
The overhung load acting on the slow speed shaft may be calculated by using the following formula.
Overhung Load = 126,000 x HP x Cf x Lf x Sf

DxN
where HP = Power Transmitted by Shaft (HP)

Cf = Load Connection Factor
Lf = Load Location Factor
Sf = Shock Factor
D= Pitch Diameter of Sprocket, etc. (in.)
N= Shaft Speed (RPM)
Table D-6. RNFM-Y1, RNHM-K1 Slow Speed Load Location Factor, Lf

L (inches)
Unit Size
¼ ¾ 1 1¼ 1½ 1¾ 2 2¼ 2½ 2¾
1120 1.05 1.18 1.25 1.32 1.38 1.44 1.51 1.57 1.67 1.80
1220 1.13 1.19 1.25 1.32 1.38 1.44 1.51 1.57 1.64 1.70
1320 1.13 1.19 1.25 1.32 1.38 1.44 1.51 1.57 1.64 1.70
1420 1.13 1.19 1.25 1.30 1.30 1.34 1.41 1.47 1.54 1.60
1520 1.13 1.19 1.25 1.30 1.30 1.34 1.41 1.47 1.54 1.60
1230 1.13 1.19 1.25 1.32 1.38 1.44 1.51 1.57 1.64 1.70
1330 1.13 1.19 1.25 1.32 1.38 1.44 1.51 1.57 1.64 1.70
L
1430 1.13 1.19 1.25 1.30 1.30 1.34 1.41 1.47 1.54 1.60
1530, 1531 1.28 1.47 1.66 1.85 1.54 2.23 2.43 2.69 2.91 3.10 Pr
Table D-7. RNFM-F1, -G1 Slow Speed Load Location Factor, Lf

L (inches)
Unit Size
½ ¾ 1 1¼ 1½ 1¾ 2 2¼ 2½ 2¾
1120 1.03 1.29 1.35 1.44 1.46 1.64 1.71 1.77 1.84 2.02
1220 1.05 1.48 1.55 1.62 1.38 1.74 1.81 1.87 1.94 2.06
Fig. D-3
Technical
1320 1.03 1.39 1.45 1.50 1.30 1.54 1.61 1.67 1.74 1.86 Information
1420 1.00 1.20 1.25 1.32 1.38 1.44 1.50 1.50 1.54 1.66
Overhung
1520 1.00 1.10 1.15 1.22 1.38 1.34 1.40 1.40 1.47 1.66
Load
1230 1.03 1.19 1.25 1.32 1.38 1.44 1.51 1.57 1.64 1.76
1330 1.03 1.09 1.15 1.22 1.38 1.34 1.41 1.47 1.54 1.66
1430 1.00 1.10 1.15 1.22 1.38 1.34 1.40 1.40 1.44 1.56
1530, 1531 1.05 1.28 1.46 1.65 1.54 2.08 2.32 2.51 2.71 3.09
Table D-8. Load Connection Factor Table D-9. Shock Factor, Sf

Type of Connection Factor Degree of Shock Factor
General Purpose Chain 1.0
Machined Gear, Pinion or Steady Loads 1.0
1.25
Synchronous Belts
Moderate Shock 1.5
V-Belt 1.5
Flat Belt 2.5 Heavy Shock 2.0
Hyponic
D-5
Moment of Inertia
Table D-10. Gearmotor Moment of Inertia Units: poundinch2
Motor Power
Motor Type 1/8 HP 1/4 HP 1/3 HP 1/2 HP 3/4 HP 1 HP
(0.1 kW) (0.2 kW) (0.25 kW) (0.4 kW) (0.55 kW) (0.75 kW)
Without Brake 1.13 1.71 2.22 2.22 3.45 4.10
3-Phase
With Brake 1.20 1.88 2.32 2.32 3.79 4.44
Without Brake 1.71 2.22 4.10
Single-Phase With Brake 1.88 2.32 4.44
Without Brake 1.71 2.22 4.10 7.28
Inverter Duty
With Brake 1.88 2.32 4.44 8.03
Motor Power
Motor Type 1.5 HP 2.0 HP 3 HP 5 HP 7.5 HP
(1.1 kW) (1.5 kW) (2.2 kW) (3.7 kW) (5.5 kW)
Without Brake 6.32 7.28 11.4 29.0 39.0
3-Phase
With Brake 7.11 8.03 12.7 32.7 42.7
Without Brake 11.4 29.0 39.0
Inverter Duty With Brake 12.7 32.7 42.7
Table D-11. Reducer Moment of Inertia Units: poundinch2
Reduction Ratio
Unit Size
5 7 10 12 15 20 25 30 40
1120 0.581 0.581 0.581 0.581 0.581 0.581 0.581 0.581 0.547
1220 0.854 0.786 0.786 0.752 0.752 0.752 0.752 0.752 0.683
1320 1.40 1.33 1.30 1.26 1.23 1.23 1.20 1.20 0.957
1420 2.60 2.43 2.26 2.22 2.15 2.08 2.05 2.05 1.47
1520 11.9 11.3 11.0 10.8 10.6 12.3 10.4 10.3 8.03
1230
1330
1430
1530
1531 4.54
Technical Reduction Ratio

Information Unit Size
50 60 80 100 120 150 200 240
of Inertia
1120 0.547 0.547

Moment
1220 0.683 0.683

1320 0.957 0.957
1420 1.47 1.44
1520 8.03 8.03
1230 0.547 0.547 0.547 0.547 0.547 0.547
1330 0.683 0.683 0.683 0.649 0.649 0.649
1430 0.957 0.957 0.957 0.752 0.752 0.752
1530 1.47 1.47 1.47 1.33 1.33 1.33
1531 4.54 4.54 4.54
Hyponic
D-6
Construction & Nameplate

Construction
Fig. D-4 Hollow Shaft Type Example (RNYM1-1530-120)
Part No. Description Part No. Description Part No. Description Part No. Description
1 Casing (1) 4 Gear 7 Bearing 10 Output shaft
2 Gear 5 Pinion shaft 8 Bearing 11 Oil seal
3 Pinion shaft 6 Hypoid pinion shaft 9 Hypoid gear 12 Casing (2)
Nameplate
Fig. D-5
Technical
Information
Construction
& Nameplate
SM-HYPONIC
CHESAPEAKE, VIRGINIA
Gearmotor Model MODEL
Input Power MOTOR H.P. CLASS AGMA Class

Output Speed OUTPUT R.P.M. RATIO Reduction Ratio
Manufacturing SERIAL NO. DATE
Date Manufactured
Serial No.
Hyponic
D-7
Output Shaft Safety Cover Dimensions

It may be mounted on either the left or right side.
C
o
Made of plastic.
Co
t
t
A
øP.C.D
øB
øB
øE
øE
A
D
Fig. D-6 Fig. D-7
Table D-12. Output Shaft Safety Cover Dimensions (Inch)

Output
Safety Cover[1] Shaft End
Frame Size Fig.
A B C D t P.C.D. N MxPXL (mm) E
1120 0.39 2.20 45° R0.12 0.08 [2] 1.18 D-6
1220,1230 0.83 2.17 5° R0.20 0.08 2.76 2 M3x0.5x6 1.57
1320,1330, 361 0.83 2.48 5° R0.20 0.08 3.07 2 M3x0.5x6 1.77
1420, 1430, 461 1.18 2.87 5° R0.20 0.08 3.46 2 M3x0.5x6 2.17
D-7
1520, 1530, 1531 1.18 3.39 5° R0.20 0.08 4.06 2 M3x0.5x6 2.56
56 1.18 3.39 5° R0.20 0.08 4.06 2 M3x0.5x6 2.95
60, 63, 64 1.57 4.33 5° R0.20 0.08 5.31 2 M3x0.5x6 3.74
M : Screw size P : Thread pitch L : Thread length P.C.D : Mounting pitch N : Q'ty
Torque Arm
Follow the steps below to check torque arm strength, driven shaft strength and
bearing life.
Table D-13
Frame Size AG (in)
Brg1
Driven shaft 1230 0.1
Brg2
Sec. B 1120, 1220, 1330, 361 0.15
m
1320, 1430, 461 0.2

YR
Y
G
Fig. D-8 1420, 1520, 1530, 1531, 56 0.25
Technical Torque arm
Information 60, 63, 64 0.30
AG
AR approximate values
rotation rotation
Safety
Cover
Shaft
R R
T+A G G T : Output torque (inlb) [3]

1. Torque arm load : R=
AR G : Hyponic Drive gravity (lb)
m (RG) YR R R : Torque arm load (lb)
2. Brg.1 load : B=
l AG : Distance between the center of driven shaft and center of gravity (in.)
AR : Distance from driven shaft center to torque arm (in.)
(R+M) (R G) YR R
3. Brg.2 load : Bw = YR : Distance from the center of Hyponic Drive to torque arm whirl stop (in.)
l
m : Distance from the center of Hyponic Drive to Brg.2 (in.)
4. Sec. B of driven shaft R : Distance between Brg.1 and Brg.2 (in.)
: M = YR R Y (R G) 0<Y m Y : Distance between the center of Hyponic Drive and Sec. B (in.)
Notes: [1] Safety cover is included with all Hollow bore Hyponics.
[2] No screw is required for safety cover for Frame Size 1120.
[3] Output torque is (+) on the shown rotation, and (-) on the opposite rotation.
Dimensions are for reference only and subject to change without notice.
Hyponic
D-8
Torque Arm
Fig. D-9 Torque Arm Mountings and Designs
1 2 3 4
Mounting examples
Torque arm must not interfere

with the motor.
1120
1220 øD a b b a øD
Drawing examples
1230
b
b
1320
1331, 361
a
a
1420
1430, 461 øH ød ød øH
1520 AR
AR
1530, 1531, 56
60, 63, 64
Machine side
Attach the torque arm to the

casing on the machine side.
Machine side
Table. D-14. Recommended Dimensions of Torque Arm Design (Inch)

Length Bore Stop Hole Mounting Pitch Mounting Hole
Frame size Thickness
AR H D a b d Technical
Information
1120 3.15 2.13 0.35 1.65 1.26 0.28 0.13
Torque Arm
1220 3.94 3.15 0.43 2.24 1.57 0.35 0.18
1230 3.94 3.15 0.35 2.56 1.57 0.35 0.24
1320 4.72 3.43 0.55 2.44 1.81 0.43 0.18
1330, 361 5.12 3.43 0.43 3.11 1.85 0.43 0.35
1420 5.51 3.82 0.71 2.95 2.24 0.55 0.24
1430, 461 6.30 3.82 0.55 3.62 2.13 0.55 0.35
1520 5.91 4.41 0.87 3.15 2.76 0.55 0.35
1530, 1531, 56 7.87 4.41 0.71 4.29 2.52 0.71 0.35
60, 63, 64 11.02 5.98 0.87 5.71 3.35 0.87 0.47
Hyponic
D-9
Mounting
1. Mounting the Shaft in the Hollow Bore 2. Securing the Shaft in the Hollow Bore
a. After coating the shaft and the reducer hollow bore with a. Refer to Fig. D-12 and Table for details on securing a staged
molybdenum disulfide, insert the shaft into the bore. shaft.
b. A clearance fit is standard. A tight fit is recommended for b. Refer to Fig. D-13 and Table for details on securing a straight
severe applications. For tight-fit applications, tap the end of the shaft using a spacer.
hollow shaft with a rubber mallet to aid insertion into the bore.
3. Shaft Removal Using fixtures i k shown in Fig. D-11 is
Using fixtures b e shown in Fig. D-10 is also recommended for
recommended for easy removal of the shaft. The shaft should be
easy assembly.
designed to allow use of these fixtures.
Fig. D-10 Driven Shaft Mounting
A2 e b Fig. D-11 Driven Shaft Removal
A3
k
A8 A7
j i
A6
A5
d c
A4
Fig. D-12 Secured by Staged Driven Shaft
L4 x L5 DEEP
L1 A1 a f
L2 L3 Fig. D-13 Secured by Spacer
h a
øD
LF
LG g
LH
L
Table D-15. Driven Shaft Mounting & Removal Detail (Inch)

Bore Size Recommended Shaft Size Recommended Component Size[1]
øD a b c d
Model
L LH LG LF L1 L2 L3 L4 L5 Thrust
min. max. A1 Nut Threaded Rod Bearing
1120 0.750 0.751 3.23 2.64 2.01 1.22 2.36 0.16 1.37 #10-32UNF 0.63 0.20 #10-32UNF #10-32UNF x 5.91 51100
1220 1.000 1.001 3.62 2.76 2.13 1.50 2.36 0.28 1.98 5/16-18UNC 0.79 0.28 5/16-18UNC 5/16-18UNC x 5.91 51100
Technical 1230 1.000 1.001 3.94 3.07 2.44 1.50 2.68 0.28 1.98 5/16-18UNC 0.79 0.28 5/16-18UNC 5/16-18UNC x 5.91 51100
Information
1320,1330,361 1.250 1.252 4.33 3.46 2.52 1.81 2.80 0.28 2.10 5/16-18UNC 0.79 0.28 5/16-18UNC 5/16-18UNC x 5.91 51100
1420,1430,461 1.375 1.377 5.43 4.41 3.39 2.05 3.66 0.39 2.32 3/8-16UNC 0.98 0.31 3/8-16UNC 3/8-16UNC x 9.45 51201
Mounting
1520,1530,1531 1.500 1.502 6.14 5.12 3.86 2.28 4.09 0.39 3.49 1/2-13UNC 1.18 0.39 1/2-13UNC 1/2-13UNC 9.45 51202
56 1.500 1.502 6.30 5.28 4.02 2.28 4.25 0.39 3.49 1/2-13UNC 1.18 0.39 1/2-13UNC 1/2-13UNC 9.45 51202
60,63,64 2.000 2.002 8.82 7.24 5.47 3.35 6.26 0.47 3.53 5/8-11UNC 1.57 0.51 5/8-11UNC 5/8-11UNC x 11.81 51204
Model Recommended Component Size[1]

e f g h I j k
Model
Retaining
A2 Bolt O.D. x I.D. Bolt A3 A4 A5 A6 A7 A8
Ring
-0.004
1120 0.59 #10-32UNF x 0.98 0.75 0.75 x 0.28 5/16-18UNC x 4.72 0.16 0.64 0.75 -0.012 4.762 5/16-18UNC 2
-0.004
1220 0.51 5/16-18UNC x 1.38 1.00 1.00 x 0.39 1/2-13UNC x 4.72 028 0.86 1.00 -0.012 6.35 1/2-13UNC 2
-0.004
1230 0.51 5/16-18UNC x 1.57 1.00 1.00 x 0.39 1/2-13UNC x 4.72 0.28 0.86 1.00 -0.012 6.35 1/2-13UNC 2
-0.004
1320,1330,361 0.51 5/16-18UNC x 1.77 1.25 1.25 x 0.67 5/8-16UNC x 5.91 0.51 1.11 1.25 -0.012 6.35 5/8-16UNC 3
-0.004
1420,1430,461 0.59 3/8-16UNC x 2.17 1.38 1.37 x 0.75 5/8-16UNC x 7.87 0.51 1.20 1.37 -0.012 7.938 5/8-16UNC 5
-0.004
1520,1530,1531 0.55 1/2-13UNC x 2.56 1.50 1.50 x 1.02 3/4-10UNC x 7.87 0.63 1.29 1.50 -0.012 9.525 3/4-10UNC 5
-0.004
56 0.55 1/2-13UNC x 2.56 1.50 1.50 x 1.02 3/4-10UNC x 7.87 0.63 1.29 1.50 -0.012 9.525 3/4-10UNC 5
-0.004
60,63,64 1.02 5/8-11UNC x 2.95 2.00 2.17 x 0.98 1-8UNC x 9.45 0.75 1.72 2.00 -0.012 12.7 1-8UNC 5
Note: [1] Parts a k are not supplied by Sumitomo Machinery Corporation of America.
Hyponic
D-10
4. Securing the Hyponic Drive to Prevent Movement Away from the Machine Side (Figs. D-14~D-16).
Collar
Snap ring Spacer End plate Set screw

Machine side
Machine side
Machine side
Fig. D-14 Secured by a Spacer Fig. D-15 Secured by Fig. D-16 Secured by a Set
and a Snap Ring an End Plate Screw and a Collar
5. Torque arm
a. Attach the torque arm to Hyponic Drive casing on the machine side with hex socket head cap screws. (Refer to the table
below for bolt sizes.)
b. Leave some allowance in the section of torque arm so that excessive force will not be applied between Hyponic Drive and the
driven shaft. Don't secure the torque arm with the torque arm bolt; otherwise, it may damage the bolt, torque arm, Hyponic
Drive or the machine.
c. For frequent start/stop operations, or repeated normal/reverse operations, use a rubber bushing between the torque arm and
mounting bolt (or spacer) to absorb the shock.
Frame size Bolt Technical

Information
1120,1230 M8
1330, 361 M10
Mounting
Torque arm
1320, 1430, 461 M12
Keep some 1420, 1530, 1531, 56 M16
Spacer allowance
1520, 60, 63, 64 M20
Flat washer No allowance between the

Machine side
Special bolt
(or pin) torque arm and the machine
(Excessive force on the torque arm

(Adjust the allowance according to
bolt, machine and Hyponic may
the movement of the machine.)
cause damage.)
Correct Incorrect
Fig. D-17 Example of Torque Arm mounting
Hyponic
D-11
Mounting cont.
6. Flange Mounting and Casing Bottom Mounting (optional)
Handle with care in order not to
apply excessive force to driven
shaft or hollow shaft by twisting
the Hyponic casing.
Correct Incorrect Incorrect
Bearing unit Bearing unit Bearing unit
Hollow shaft type Hollow shaft type Hollow shaft type

Hyponic Drive Hyponic Drive Hyponic Drive
Fig. D-18 Flange Mounting Surface (Poor concentricity of the driven (Poor perpendicularity of the driven shaft
shaft and mounting flange) center and mounting flange surface)
(Excessive force on Hyponic and the bearing

unit may cause damage on inner parts.)
Lubrication
Hyponic drives are filled with long-life grease and sealed, so replenishment is practically unnecessary, but overhaul in
approximately 20,000 hours or three to five years of operation will provide longer service life. The durability of oil
seals is subject to operating conditions. Under severe conditions, they may require changing in less than 20,000
hours or three years of operation. Overhaul of gearmotors must be performed at factory-authorized locations.
Paint And Rust Proofing Specifications

Table D-16. Paint Specifications
Technical
Information
Paint Classification Paint Name Paint Color Resin Type Dry Time
Paint & Rust
Speed Dry DTM Water Water Based

Lubication
Standard Based Enamel Blue Acrylic Polymer 1~11¦2 hours

Polymide
Epoxy (Optional) Heavy-Duty Epoxy Blue 4~6 hours
Converted Epoxy
Food and Beverage
FDA-USDA (Optional) High Gloss White Modified Alkyd 4~7 hours
Industry Coating
Rust proofing treatment is applied to all completely assembled models prior to shipment.
Table D-17. Rust Proofing Specifications

Lubrication Type Grease Oil
Rust-Proofing Period[1, 2] 1 Year 6 Months
Indoor environment that is relatively free of humidity,
Storage Condition[2] dust, extreme temperature fluctuation, corrosive
gas, etc.
Notes: [1] All oil-lubricated models for export receive rust-proofing treatment that is
effective for 6~12 months. Please specify Export Rust-Proofing for all export
models.
[2] Please consult factory for storage longer than those listed in Table D-17 or in
the event of adverse storage conditions.
Hyponic
D-12
Motor
Conduit Box Specifications
Standard Motor Characteristics
Brakemotor Characteristics
Technical
Information
Motor
Hyponic
D-13
Conduit Box Mounting Direction

The direction in which the conduit box is mounted may be Fig. D-19 Conduit Box Mounting Direction (3-Phase
changed in 90° increments. A mounting direction other than Standard and Inverter Duty Motors)
standard must be changed by the factory and specified when
an order is placed. When ordering, refer to Fig. D-19 for lead
wire opening direction and mounting direction. The direction Up
cannot be changed after shipment.
Left Right
Standard
The mounting directions indicated in Fig. D-19 are viewed from the
opposite side of the fan cover. Arrows indicate lead wire opening
direction. Please consult factory for brakemotor, plug-in shaft, bolt-on
flange and bolt-on feet models.
Motor Cover Mounting Specifications

Refer to the dimension FA or FB in Figure D-20 when Fig. D-20 Motor End Clearance
designing the mounting space into which the gearmotor is to fit.
1. Dimension FA: The space necessary to remove the fan FA or FB
cover or brake cover without removing the motor for the
equipment. Note: It is not necessary to remove the
gearmotor from the equipment when removing the fan or
brake cover
2. Dimension FB: The minimum space required for
adequate ventilation
Table D-18. Space Requirements (Inch)

Motor Standard Motor Brake Motor
HP x 3 Phase Inverter Duty 3 Phase Inverter Duty
Pole FA FB FA FB FA FB FA FB
Technical
Information
1/8 x 4 1.9 0.8 2.0 2.5 0.8
1/4 x 4 1.9 0.8 1.9 0.8 2.5 0.8 2.5 0.8

Motor
1/3 x 4 1.9 0.8 1.9 0.8 2.5 0.8 2.5 0.8
1/2 x 4 1.9 0.8 2.0 0.8 2.5 0.8 3.7 0.8
3/4 x 4 2.0 0.8 2.1 0.8 3.7 0.8 4.6 0.8
1x4 2.0 0.8 2.1 0.8 3.7 0.8 4.6 0.8
1.5 x 4 2.1 0.8 2.2 0.8 4.6 0.8 5.2 0.8
2x4 2.1 0.8 2.2 0.8 4.6 0.8 5.2 0.8
3x4 2.2 0.8 2.4 0.8 5.2 0.8 5.2 0.8
5x4 2.4 0.8 2.4 0.8 5.2 0.8 5.2 0.8
7.5 x 4 2.4 0.8 3.0 1.0 5.2 0.8 6.7 1.0
Hyponic
D-14
Conduit Box Dimensions

Fig. D-21 Global Conduit Box (UL Washdown) Fig. D-22 Indoor Duty Conduit Box (Option)
Table D-19. Conduit Box Dimensions (Inch)

Frame HP Specification AB C D F G X E
Size
Global Conduit Box 5.04 5.91 4.92 2.48 3.43 NPT 1/2
1/8
F63S UL Washdown
Washdown 5.00 5.16 3.94 2.20 2.95 1.40 (1/8 HP) PF 1/2
1/4
F63M UL Indoor 5.20 5.67 4.80 2.64 3.03 2.30 N/A
1/3
F71M Non UL w/ Brake 3.50 4.37 3.94 2.09 2.28 (1/4 ~ 1/2 HP) N/A
1/2
Non UL w/o Brake 3.35 4.37 3.35 2.09 2.28 N/A
UL Washdown
Washdown 5.35 5.16 3.94 2.20 2.95 PF 3/4
F80S 3/4
UL Indoor 5.59 5.67 4.80 2.64 3.03 3.80 N/A
F80M 1
Non UL w/ Brake 5.59 5.67 4.80 2.64 3.03 N/A
Non UL w/o Brake 4.49 3.78 3.35 1.89 1.89 N/A
UL Washdown
Washdown 5.55 5.16 3.94 2.20 2.95 PF 3/4
F90S 1.5
UL Indoor 5.79 5.67 4.80 2.64 3.03 3.90 N/A
F90L 2
Non UL w/ Brake 5.79 5.67 4.80 2.64 3.03 N/A
Non UL w/o Brake 4.69 3.78 3.35 1.89 1.89 N/A
UL Washdown
Washdown 5.83 5.16 3.94 2.20 2.95 PF 3/4
F100L 3 UL Indoor 6.06 5.67 4.80 2.64 3.03 4.10 N/A
Technical
Non UL w/ Brake 6.06 5.67 4.80 2.64 3.03 N/A Information
Non UL w/o Brake 4.96 3.78 3.35 1.89 1.89 N/A

Motor
UL Washdown
Washdown 7.20 6.02 3.94 2.56 3.46 PF 3/4
F112M 5 UL Indoor 6.69 5.67 4.80 2.64 3.03 5.00 N/A
Non UL w/ Brake 6.69 5.67 4.80 2.64 3.03 N/A
Non UL w/o Brake 5.79 4.41 3.94 2.09 2.32 N/A
Global Conduit Box 6.54 5.91 4.92 2.48 3.43 NPT 1
UL Washdown
Washdown 7.20 6.02 3.94 2.56 3.46 PF 1
F132S 7.5 UL Indoor 6.69 5.67 4.80 2.64 3.03 5.00 N/A
Non UL w/ Brake 6.69 5.67 4.80 2.64 3.03 N/A
Non UL w/o Brake 5.79 4.41 3.94 2.09 2.32 N/A
Hyponic
D-15
Standard Motor Characteristics

Standard Motor Data
Full Load ratings and amperage for Hyponic® gearmotors are listed in Tables D-20~D-22. These ratings are
based on the motors design values. If additional information is required, please consult the factory.
Table D-20. 230/460 V, Synchronous Speed 1800 RPM, 60 Hz, Continuous Duty, TEFC
Full Load Full Load Current (A) Starting Current (A) Torque (% of F.L.) Power Code Inertia WR 2
Frame Efficiency
HP Torque Factor
Starting Breakdown (Percent) (Percent) Letter
[1]
Size RPM 230V 460V 208V 230V 460V lbin 2
inlbs
1/8[2] F-63S 1730 4.50 0.7 0.35 0.65 2.8 1.4 326 329 64.0 59.5 K 1.11
1/4 F-63M 1730 9.06 1.1 0.6 1.1 5.2 2.6 300 293 69.8 65.2 K 1.71
1/3 F-63M 1710 12.3 1.3 0.65 1.3 5.2 2.6 232 232 70.8 72.0 G 1.71
1/2 F-71M 1740 18.3 2.1 1.1 2.0 9.8 4.9 295 280 71.9 65.1 J 2.22
3/4 F-80S 1730 27.4 2.5 1.2 2.5 12.3 6.2 266 245 76.9 73.0 H 3.45
1 F-80 1750 36.0 3.4 1.7 3.4 17.6 8.8 269 303 77.2 72.3 H 4.10
1.5 F-90S 1730 54.7 4.7 2.4 4.7 28.6 14.3 273 281 80.3 74.1 J 6.32
2 F-90L 1740 72.5 6.1 3.0 6.2 36.8 18.4 263 270 82.3 75.6 J 7.28
3 F-100L 1730 109 8.5 4.3 8.7 54.8 27.4 277 266 84.4 77.2 J 11.4
5 F-112M 1730 183 13.1 6.6 13.7 91.5 45.8 308 279 86.3 82.4 J 29.0
7.5 F-132S 1710 277 18.1 9.0 20.1 120 60 230 223 86.9 88.1 H 39.0
Table D-21. 575 Volt, Synchronous Speed, 1800 RPM, 60 Hz, Continuous Duty
Full Full Load Starting Torque (% of F.L.) Power Inertia WR2
HP Frame Efficiency Code
Torque Current (A) Current (A) Factor inlbs
Size RPM 575V 575V Starting Breakdown (Percent) Letter[1]
inlbs.
1/8 [2]
F-63S 1720 4.58 0.28 1.3 376 391 65.2 54.1 L 1.11
1/4 F-63M 1720 9.17 0.48 2.2 316 340 69.4 60.3 K 1.71
1/3 F-63M 1710 12.8 0.52 2.2 250 270 71.3 67.7 H 1.71
1/2 F-71M 1700 18.6 0.79 3.7 309 300 75.8 67.4 H 2.22
3/4 F-80S 1720 27.5 0.94 4.5 247 227 77.4 75.9 G 3.27
Technical 1 F-80M 1680 37.5 1.3 6.6 252 256 78.1 74.9 H 4.10
Information
1.5 FA-90S 1740 54.3 1.84 12.4 319 364 85.7 71.1 K 11.4
2 FA-90L 1730 72.9 2.36 16.6 326 371 86.1 73.6 K 11.4
Motor
3 FA-100L 1750 108 3.26 27.5 354 417 87.9 78.5 L 29

5 FA-112M 1740 181 5.17 40 295 346 88.7 81.7 J 39
7.5 FA-132S 1750 270 7.47 53.2 288 331 89.9 83.6 H 91.6
Table D-22. Single Phase, 115/230V, Synchronous Speed, 1800 RPM, 60 Hz, TEFC
Full Load Amp. Inertia WR2
HP RPM Frame Size
115 V 230 V lbin 2
1/8 S-71S 3.4 1.7 5.13
1/4 S-71S 4.2 2.1 5.13
1/3 1750 S-71 6.5 3.2 7.69
1/2 S-71 7.1 3.5 7.69
Notes: [1] Code letter shown is for 230V or 460V operation. Consult the factory for other voltages.
[2] No Fan 1/8 H.P., F-63S frame.
Hyponic
D-16
Standard Wiring Diagrams

Illustrated below are the wiring diagrams for our standard motors. For additional information, please refer to motor
nameplate. Due to changes in design features, this diagram may not always agree with that on the motor. If different,
the motor diagram found inside the conduit box cover is correct.
A. Three Phase Motors

Fig. D-23 Y-Connected (5 HP and smaller) Fig. D-24 Delta-Connected (7.5 HP)
Line 208/230V 60 Hz Line 460V 60 Hz Line 208/230V 60 Hz Line 460V 60 Hz
B. Single Phase Motors

Fig. D-25
Line 115V Line 230V or 208V
Technical
Information
Motor
Hyponic
D-17
Assembly Drawings
Assembly of Motors
Fig. D-26 Frame Size F-63M thru F-160M
Table D-23. Part Name

1 Bearing Cover[1] 13 Stationary Core
Technical 2 Bearing 14 Stator Frame
Information
3 Bolt[1] 15 Stator Winding
4 Fan [2]
16 Bolt
Motor
5 Fan Cover 17 Eye Bolt

6 End Bracket 18 Cyclo Flange Bracket
7 Bolt 19 Bearing
8 Bolt 20 Slinger/Oil Seal
9 Internal Fan 21 Motor Shaft
10 Hub 22 Conduit Box
11 Short Circuit Ring 23 Bearing Cover
12 Rotor Core 24 Bearing Sleeve
Notes: [1] Parts not included in F-63 through F-132S Motors.

[2] No Fan 1/8 H.P., F-63S frame.
Hyponic
D-18
Motor Thermal Ratings

Table D-24. Motor Thermal Rating (C x Z)[1]
Motor Power Allowable C x Z Motor Moment of Inertia(lb-in2)
HP (35%ED)[2] 35% - 50% ED[2] 50% - 80% ED[2] 80% - 100% ED[2] Standard With Brake
1/8 3200 3000 2000 1200 1.13 1.20
1/4 2200 2800 2800 2500 1.71 1.88
1/3 2200 2800 2800 2500 1.71 1.88
1/2 1800 2200 1500 1500 2.22 2.33
3/4 1800 2200 1500 1500 3.45 3.80
1 1400 1400 800 500 4.10 4.45
1.5 1400 1400 800 500 6.33 7.11
2 1200 1200 500 400 7.28 8.04
3 1000 900 400 200 11.4 12.8
5 800 800 800 700 29.0 32.8
7.5 300 300 200 150 39.1 42.9
The calculated C x Z value (steps 1 - 3 outlined below) should be less than the allowable value listed in Table D-24
1. Obtain the C value.
I M + IL IM = Moment of inertia of motor.

C=
IM IL = Total moment of inertia of load as seen from the motor.
2. Obtain the Z value (number of starts per hour).
(a) Assume that one operating period consists ofon time ta (sec), off time tb (sec) and the motor is started nr
(times/cycle).
3600nr
Zr = (times/hr)
ta + tb
(b) When inching, ni (times/cycle) is included in 1 cycle (ta+tb), the number of inching times per hour, Zi,
is then included in the number of starts.
Technical
Information
3600ni
Zr = (times/hr)
ta + tb
Motor
(c) Calculate Z by adding Zr to Zi.
3600 1
Z = Zr + 1 Zi = (nr + ni) (times/hr)
2 ta + tb 2
3. Calculate C multiplied by Z.
Use the value of C obtained in step 1 and Z from step 2.
4. Obtain the duty cycle %ED and check with Table D-24.
ta
%ED = x 100 ta = on-time
ta +tb tb = off-time
Notes: [1] Please consult the factory for Inverter Duty and Single Phase motors.
[2] %ED = Duty Cycle
Hyponic
D-19
Brakemotor Characteristics
Brakemotor Data
The brakemotor on Hyponic® gearmotors operates When used for outdoor installations, our standard
with direct current supplied by a dual voltage rectifier brakemotor must be protected by some type of cover.
mounted in the motor conduit box. Such covers are available from the factory; please
inquire when ordering.
The standard brake input voltage is 208V OR 230V OR
460V at 60 Hz.
Table D-25. Required Brake Torque [1]

% Motor Typical
Condition Torque Application [2] Remarks
Machine Tool Cutter and

Rapid Brake Action 100% Table Transfer
Fast Brake Action or Quick
Frequent Start/Stop 100% Conveyor Drive
Brake Relay May Be Required
Wiring Connection for Fast Brake
Rapid Braking and Fail Safe Over 150% Crane, Hoist Winch, Gate, Lifting
Action or Quick Brake Relay
Rapid Deceleration of
Over 150% Centrifuge Drive Textile
High Inertia
Table D-26. Brakemotor Characteristics

Type Brake Torque Inertia WR 2 Brake Delay Time (sec) Coil Current (AC Amperage)
Standard Maximum Normal Fast or Quick
HP Motor Brake
lbin 2 Braking Braking 208V 230V 460V
Frame Model ftlbs ftlbs Action Action
1/8 F-63S FB-01A 0.7 1.0 1.20 0.15~0.2 0.015~0.02 0.06 0.06 0.04
1/4 F-63M FB-02A 1.5 2.0 1.88 0.15~0.2 0.015~0.02 0.1 0.1 0.06
1/3 F-63M FB-02A 1.5 2.9 1.88 0.15~0.2 0.015~0.02 0.1 0.1 0.06
1/2 F-71M FB-05A 3.0 3.0 2.31 0.1~0.15 0.01~0.015 0.1 0.1 0.06
3/4 F-80S FB-1B 5.5 7.7 3.79 0.2~0.3 0.01~0.02 0.1 0.1 0.1
1 F-80M FB-1B 5.5 7.7 4.44 0.2~0.3 0.01~0.02 0.1 0.1 0.1
Technical 1.5 F-90S FB-2B 11 14.0 7.11 0.2~0.3 0.01~0.02 0.3 0.3 0.2
Information
2 F-90L FB-2B 11 14.0 8.03 0.2~0.3 0.01~0.02 0.3 0.3 0.2
3 F-100L FB-3B 16 21.0 12.7 0.3~0.4 0.01~0.02 0.4 0.4 0.2
Motor
5 F-112M FB-5B 27 36.0 32.7 0.4~0.5 0.01~0.02 0.4 0.5 0.3

7.5 F-132S FB-8B 41 53.0 42.7 0.3~0.4 0.01~0.02 0.4 0.5 0.3
Notes: [1] If application requires larger or smaller brake torque than those listed, please advise the factory when ordering.
[2] Quick brake relay may not be used with inverter applications.
Hyponic
D-20
Standard Wiring Connection, Dual Voltage

Models FB-01A thru FB-8B
D-27 D-28
D-29 D-30
Technical
Information
MC: Electromagnetic Relay
MCB: Magnetic Circuit Breaker
Motor
OLR: Overload or Thermal Relay Table D-27. Varistor Specifications
VR: Varistor (protective device) [1] Operating Voltage 200-230V 380-460V 575V
Varistor Rated Voltage AC260~300V AC510V AC604V
Varistor Voltage 430~470V 820V 1000V
FB01A, 02A Over 0.2W Over 0.4W
FB-05A Over 0.2W Over 0.4W
FB-1B Over 0.4W Over 0.6W Over 0.4W
Rated Watt
FB-2B, 3B Over 0.6W Over 1.5W Over 0.6W
FB-5B, 8B Over 0.6W Over 1.5W Over 1.5W
Note: [1] Refer to Table D-27 for Varistor Specifications.
Hyponic
D-21
Standard Wiring Connection

Quick Brake Relay Equipped Models
Fig. D-31 Quick Brake Action, High Voltage Fig. D-32 Quick Brake Action, Low Voltage
(FB-2B, FB-3B, FB-5B, FB-8B) (FB-05A, FB-1B, FB-2B, FB-3B)
Motor QB Relay Rectifier Brake Motor QB Relay Rectifier Brake
T1 T2 T3 1 2 3 4 1 2 3 4 M N T1 T2 T3 1 2 3 4 1 2 3 4 M N
OLR
OLR
Furnished Furnished by
MC MC Customer
by
Customer
LINE 460V
Line 230V
FB Brake (1/8 HP 7.5 HP) with Inverter

D-33 D-34
D-35 D-36
Technical
Information
Motor
MC: Electromagnetic Relay

MCB: Magnetic Circuit Breaker
VR: Varistor (protective device) [1]
Note: [1] Refer to Table D-27 for Varistor Specifications.
Hyponic
D-22
Assembly of Brakemotors
Types FB-01A, 02A, 05A, 1B, 2B, 3B, 5B, 8B Table D-28a. Type FB-01A, -02A, -05A
Part No. Description
Fig. D-37 Brakemotor 1 Stationary Core
2 Spacer
3 Brake Lining
7 6 5 4 3 2 1 4 Restraining Bolt
a. 5 Hub
6 C-type Retaining Ring
7 Cover
8 Fan (TEFC model only)
9 Leaf Spring
10 Brake Shoe
11 Armature
12 Pressure Spring
13 Solenoid Coil
14 Ball Bearing
15 Motor Shaft
Table D-28b. Type FB-1B thru 3B

Part No. Description
1 Stationary Core
2 Brake Release Support
3 Shifting Pin
4 Spacer
8 9 10 11 12 13 14 15 5 GAP Adjusting Sleeve
6 Brake Release Lever
Type FB-01A, 02A, 05A
7 Restraining Bolt
8 Brake Lining
9 Leaf Spring
10 Hub
b. 11 Retaining Ring
12 Fan Cover
13 Fan Set Screw
14 Fan
15 Fixed Plate
16 Noise Shield
17 Brake Shoe
18 Armature Plate
19 Pressure Spring
20 Solenoid Coil
21 Fan Side Motor Bearing
22 Motor Shaft Technical
Information
Table D-28c. Type FB-5B thru 8B
Type FB-1B thru 3B Part No. Description
Motor
1 Stationary Core
2 Brake Release Support
3 Stud Bolt
4 GAP Adjusting Sleeve
5 Shifting Pin
c. 6 Brake Release Lever
7 Spring Washer
8 Nut
9 Brake Lining
10 Hub
11 Retaining Ring
12 Fan Cover
13 Fan Set Screw
14 Fan
15 Brake Shoe
16 Armature Plate
17 Pressure Spring
18 Solenoid Coil
19 Fan Side Motor Bearing
Type FB-5B thru 8B 20 Motor Shaft
21 Bearing Cover
Hyponic
D-23
Assembly of Brakemotors
Rectifier Data
Table D-29. Rectifier Data
Brake Motor Voltage Rectifier P.N. Product I.D.
Type (HP x P) (V) Single Voltage [1] Number
190 ~ 230
FB-01A 1/8 x 4 380 ~ 460 25FW - 4FB DX527WW-01
1/4 x 4 190 ~ 230
FB-02A 25FW - 4FB DX527WW-01
1/3 x 4 380 ~ 460
190 ~ 230
FB-05A 1/2 x 4 25FW - 4FB DX527WW-01
380 ~ 460
3/4 x 4 190 ~ 230
FB-1B 25FW - 4FB DX527WW-01
1x4 380 ~ 460
1.5 x 4 190 ~ 230
FB-2B 1x4 380 ~ 460 25FW - 4FB DX527WW-01
190 ~ 230
FB-3B 3x4 380 ~ 460 25FW - 4FB DX527WW-01
190 ~ 230
FB-5B 5x4 25FW - 4FB DX527WW-01
380 ~ 460
190 ~ 230
FB-8B 7.5 x 4 380 ~ 460 25FW - 4FB DX527WW-01
Note: [1] Dual Voltage P.N. 25FW-4FB is now standard for all FB brakes. The voltage range is 190 ~ 460V.
Technical
Information
Motor
Hyponic
D-24
Standards
Motor Protection
International Standards & Sumitomo Standards
EC Directives & CE Markings
Precautions for Inverter Driving
Constant Torque Operation of General Purpose Motors
Technical
Information
Standards
Hyponic
D-25
Motor Protection
}
The first number (No. 1) denotes the level of motor protection against human or other foreign substances. Classified according
The second number (No. 2) denotes the level of motor protection against water permeation. to combination.
Table D-31. Protection Method of Motors
First Second Number (No. 2)[1, 2, 3]
Number 0 2 3 4 5 6 7 8
(No. 1) Non-Protected Drip-Proof Spray-Proof Splash-Proof Water-Jet-Proof Sea-Wave-Proof Immersion-Proof Submersible
0
Non-Protected IP00 X X X X
1
Semi-Protected IP10 IP12 X X X
2
Protected IP20 IP22 IP23 IP24 X X X
4
Totally Enclosed X IP44 IP45
5
Dust-Protected X IP54 IP55 IP56
6
Dust-Tight IP65
Table D-32. First Number Description

Type Number Description
Constructed without special protection against human contact and penetration of solid foreign
Non-Protected 0 objects.
Constructed to prevent inadvertent contact with rotating and conductive parts inside the
Semi-Protected 1 machine, by hand or other critical parts of the human body. Constructed to prevent penetration
of solid foreign substances over 50 mm in diameter.
Constructed to prevent contact with rotating and conductive parts inside the machine, by hand or
Protected 2 other critical parts of the body. Constructed to prevent penetration by solid substances over 12
mm in diameter.
Constructed to prevent contact with the rotating and conductive parts inside the machine by
tools, electric wires, etc. with minimum width and thickness over 1 mm. Constructed to prevent
Totally Enclosed 4 penetration of solid foreign substances over 1 mm diameter. However, water drainage outlet and
exhaust outlet may be of Number 2 construction.
Constructed to prevent contact with rotating and conductive parts inside the machine by any
Dust-Protected 5 form of objects. Constructed for protection against dust particle penetration, but will not interfere
with normal operation, despite such penetration.
Constructed to prevent contact with rotating and conductive parts inside the machine by any
Dust-Tight 6 form of objects. Constructed to prevent ingress of dust particle penetration.
Table D-33. Second Number Description

Type Number Description
Technical Non-Protected 0 Constructed without special protection against water permeation.
Information
Constructed to prevent harmful effect from dripping water falling from within 15
° direction from
Drip-Proof 2 vertical.
Standards
Constructed to prevent harmful effect from dripping water falling from within 60
° direction from
Spray-Proof 3 vertical.
Splash-Proof 4 Constructed to prevent harmful effect from dripping water falling from any direction.
Water-Jet Proof 5 Constructed to prevent harmful spray from any direction.
Sea-Wave Proof 6 Constructed to prevent harmful effect from strong spray from any direction.
Constructed for submersion into water of prescribed depth and time but not having any harmful
Immersion-Proof 7 effect in spite of water permeation.
Submersible 8 Constructed to assure normal operations under water.
Example:
IP 5 4
Form of protection against water permeation: Splash-Proof Type
Form of protection against bodily injury and solid foreign substance peneration: Dust-Proof Type
ICE Standards abbreviation.
Table C-26 Cooling

Enclosure Construction JEC Standards IEC Standard
Totally Enclosed, Non-Ventilated (TENV) JCN4 IC410
Totally Enclosed, Fan-Cooled (TEFC) JC4 IC411
Notes [1] X denotes a protection combination that is difficult to produce.
[2] IP44 and IP54 are standardly available from Sumitomo.
[3] Please consult factory for IP45 and IP55 selections.
Hyponic
D-26
International Standards &
Corresponding Sumitomo Standards
UL Standards (Underwriters Laboratories)
UL Standards, which are based on a series of scientific not regulated to comply with U.S. Federal Government
studies, research and experiments, are established for standards, but they are regulated by some U.S. cities
safety by a commercial testing institute in the U.S. to and states.
prevent fire, disaster and harm to human life. They are
Table D-35
Non-explosion proof Non-explosion proof 3-phase induction motor
Motor single-phase induction 3-phase induction motor with brake
motor[1]
Power 1/8~1/2HPx4P 1/8~7.5HPx4P 1/8~7.5HPx4P
Voltage 115V, C230V 208V, 230V, 460V, 575V UL mark
Frequency 60Hz 60Hz

Insulation Class A Class A (Class B, Class F) [3] Class F
Ambient Conditions Indoor type[2]
HP P TYPE
VOLTS FRAME
Differences from Sumitomo Machinery Corporation of America (SMA) standard models: Hz INS. CLASS
AMP TIME RATING
Numbered motor leads RPM SERVICE FACTOR
Nameplate with UL mark CODE
SER. NO.
MAX AMB C
Large volume terminal box

UL recognized insulation system. SUMITOMO MACHINERY CORP. OF AMERICA
Fig. D-42 UL nameplate

Additional Remarks:
Manufacturing and repair work may be conducted only at an authorized facility.
CSA Standards (Canadian Standards Association)
CSA Standards are standards that have been established by a semi-governmental
organization in Canada. Most areas in Canada require electronic products to be approved
by CSA.
Table D-36
Single phase induction 3-phase induction motor High efficiency 3-phase High efficiency 3-phase
Motor 3-phase induction motor induction motor with
motor[1] with brake induction motor
brake
Power 1/8~1/2HPx4P 1/8~1HPx4P 1/8~1HPx4P 2~7.5HPx4P 2~7.5HPx4P
Voltage 115V, A230V 208V, 230V, 460V, 575V
Frequency 60Hz
Insulation Class B and Class F[3]
Ambient conditions Indoor type[2] Technical
Information
Differences from SMA standard models:
Standards
Numbered motor leads
Oversized frame for a high-efficiency motor
Nameplate with CSA mark
Large volume terminal box
CSA standard motor coil. VOLTS
HP P TYPE
FRAME
Hz M / B INS. CLASS /
Additional Remarks: M.AMP TIME RATING
RPM SERVICE FACTOR
If the unit is to be exported to Canada, it should include a CSA approved motor. B.AMP MAX.AMB C
B.TORQUE FT-LB ENCLOSURE TE
Manufacturing and repair work may only be done at authorized facilities. MANUF. No.
Inverter (AF) motors are excluded from UL approval. Sumitomo supplies CSA compliant AF
SM CYCLO OF CANADA, LTD
TORONTO, MONTREAL, VANCOUVER
motors (CSA mark is not fixed on the nameplates of CSA compliant products). Fig. D-43 CSA nameplate
NRCan established the Energy Efficiency Act (EEACT) in 1992 and the Energy Efficiency Regulations
(EER) in 1995. Additional regulations were applied to gearmotors imported on November 27, 1999 or later.
The import of gearmotors that do not meet the efficiency standards has been banned.
Notes: [1] Contact factory for manufacturers of single-phase motors or brakemotors.

[2] The outdoor type is unavailable.
[3] Contact the factory for manufacture of insulation types B or F.
Hyponic
D-27
NEMA Standards (National Electrical Manufacturers Association)

Established by a manufacturers association to provide manufacturer and consumer
standards for most electrical products.
Differences from Sumitomo Machinery Corporation of America standard models: HP P TYPE
VOLTS FRAME
Numbered motor leads Hz M B INS. CLASS
M. AMP TIME RATING
Nameplate marked with NEMA design RPM SERVICE FACTOR
NEMA standard motor coil. CODE
B. AMP
MAX. AMB.
B. TORQUE
C
FT LB
SERIAL NO. NEMA DESIGN
Additional Remarks:
SUMITOMO MACHINERY CORP. OF AMERICA
No approval is required to state NEMA compliance.
Fig. D-44 NEMA nameplate
NEMA standards also apply to inverter motor (AF).
Other Standards
Table D-37. Application of International Standards (Example)
Japan 000 GermanyVDE

JIS
Country/Standards JEM
JEC InternationalIEC UKBS DIN
: 4kW max. : 4kW max. : Sumitomo standards

Standard output
: 5.5kW min. : 5.5kW min.
: Manufactured to special specification
Applicable output frame size on customers request
Motor mounting dimension [1] [1] [1] [1]
of corresponding frame size
[1] [1] [1] [1]
Shaft end dimension
Dimension tolerance of shaft [1] [1] [1] [1]
end key and key groove
IECInternational Electrotechnical
Insulation class
Commission.
Lead wire code BSBritish Standards.
Standard direction of
rotation
Description on nameplate
Characteristic testing method
Standard voltage 200V 220V 220V

415V
400V 440V 380V
Standard frequency 50Hz 60Hz 50Hz 60Hz 50Hz 50Hz
Note: [1] Denotes dimension of standard flange-mount CYCLO DRIVE. Consult the factory for flange
dimensions required for standards.
Technical
Information
Standards
Hyponic
D-28
EC Directives & CE Marking

The CE mark is affixed to products that conform to EC products and ensure free distribution of products across
directives in order to certify the quality and safety of borders within the region of the EU (European Union).
EC Directives Applicable to Machine Products and Implementation Period
Table D-38. Directives that Apply to Ordinary Machine Products

Details Objects Details of directive
EC directives
Machinery Directive Essential matters related to safety of machines
Aggregates of parts, which are movable are stipulated. Machines that are electrically
Machinery
(Industrial machines, primarily) dangerous must meet the requirements for low
Directive
voltage.
Low Voltage Directive Products driven by power of 50-1,000 VAC or
Products not conforming to standards cannot be
Low Voltage 75-15,000 VDC
put on the market.
Directive
EMC Directives EMI : Not to cause external electromagnetic

Electromagnetic All types of products that may cause jamming interference
Compatibility (electromagnetic radiation) or have their EMS : To withstand external electromagnetic
Directive functions impeded by nearby radio waves interference
Electromagnetic
Table D-39. Transition Period and Time Limit for Enforcement of CE Marking for Major Directives
Year 1990 1991 1992 1993 1994 1995 1996 1997 1998 1999 2000 2001 2002 2003
EC Directive
Machinery Directive
89/392/EEC Original 1/1 1/1
91/368/EEC Revision I Transition Enforcement
93/44/EEC Revision II
EMC Directives 1/1 1/1

89/336/EEC Original Transition Enforcement
92/31/EEC Revision I
Low Voltage Directive 1/1 1/1 Technical

Information
73/23/EEC Original Transition Enforcement
Standards
93/68/EEC Revision I
Measures to Take for EC Directives and CE Marking Related to Gearmotors

Among EC directives, the machinery directive (issued in The EMC directive (issued in January 1996) does not
January 1995) concerning induction motors and low apply to induction motors.
voltage directive (issued in January 1997) are
applicable.
CE marking logo shown

on nameplates
Hyponic
D-29
EC Directives & CE Marking, cont.
Standard Specifications for CE Marking Motors

Input power : 0.1kW~4kW 230/400V 50Hz Dual voltage direct starting
Y
5.5kW or more 400V 50Hz Start
Insulation : 0.1kW~0.4kW Class E
0.75kW or more Class B
Rated time : Continuous
Characteristics : IEC34-1
Protection : IP54 (without brake), IP44 (with brake)
Terminal box : (Material) 5.5kW or less: Aluminum (PG16 boltsx2pcs)
7.5kW or more: cast iron (PG21 boltsx3pcs)
(specification) Terminal plate (six terminals European style)
with grounding terminal
Conduit tube in European size ( PG bolts) different from Japanese
standard of conduit tube PF bolts
Insulation : Distances between insulated surfaces and spaces in accordance with IEC standards
External dimensions : Same as standard except for the terminal box
TEUV test report : Acquired for a representative model 0.75kWx4p, 230V/400V (Oct 1996)
CE marking motors are manufactured in accordance with the model
Declaration of Conformity : Declaration of Conformity is available when necessary for CE marking
Fig. D-45 Example of Terminal Box 5.5 kW or less Terminal plate

97
81 (six terminals 59
50 in European
style)
56
49
Technical
Information
Standards
Connection 16 16 2-PG16 30.5

bar
Manufacturing Range of CE Marking Motors

Table D-40. 3-phase Induction Motor
230/400V dual voltage 400V
Input Power Symbol 01 012 018 02 03 04 05 08 1 1H 2 3 5 6 8
kWx4P (0.1) 0.12 0.18 (0.2) 0.25 0.37 (0.4) 0.55 0.75 1.1 1.5 2.2 (3.7) 4 5.5
Frame F63S F63M F71M F80S F80M F90S F90L F100L F112M F132S
Motors with kWs not shown in parentheses ( ) in the above table are standard in Europe, while motors with kWs shown in
parentheses ( ) are used only in Japan and other countries.
European standard kW motors are recommended. Motors with kWs shown in parentheses ( ) are also available
3-Phase 100V/50Hz, 200V/60Hz, 220V/60Hz
3-Phase 400V/50Hz, 400V/60Hz, 440V/60Hz
3-Phase 380V/50Hz
3-Phase 415V/50Hz
Contact the factory when motors with kW and voltage not listed in Table D-37 are required.
Hyponic
D-30
Precautions for Inverter Driving

1. Constant Torque Operation
Constant torque operation requires a special motor for the inverter. Consult factory when the operation frequency range is les
s than 6 Hz.
The sensorless operation mode of the HF-320 inverter permits constant torque operation of general-purpose motors at 3.7 kW oress. l
2. Operation in Frequency Range Exceeding the Base Frequency (60 Hz)

Rated output operation will be carried out in the frequency range exceeding the base frequency. Therefore, the torque will dec rease as the
speed increases. Select an appropriate motor capacity according to the machine load characteristics. (See Fig. D-46.)
The frequency exceeding 60 Hz is regarded as the base frequency. The output torque is lower than that at 60 Hz, which is the standard base
frequency, also when V/f is set for constant torque operation.
When such adjustment is made, insufficient torque may result at low frequency or during start-up.
Do not change the base frequency figure for cases other than reduction load characteristics.
3. V/f Mode Operation of General-purpose Inverter

In the case of multiple operation of motors or V/f operation with an inverter that has no sensorless function, it is necessaryto adjust the boost
value to compensate for the start-up torque and slow-speed torque. Standard values are usually set before shipment from the ma nufacturer
but overcurrent may result depending on the load condition and acceleration/deceleration. In such a case, change values approp riately as
follows : Fig. D-46
a. In the case of a small capacity motor and a small load, a large boost setting may cause Output frequency (Hz)
overexcitation of a motor, leading to overcurrent. In that case, lower the boost to return
to a normal value.
b. In cases where a load is large and overcurrent during start-up and slow-speed Base frequency
operation easily causes tripping, increase the boost to lower the current value. Examine
the motor capacity if no improvement is observed after boost adjustment.
Boost
4. Operation by Sensorless Vector Inverter
Base voltage
Some of the newest high-performance inverters are equipped with asensorless vector Output voltage (V)
operation function. Usually this function is valid only when a motor and an inverter are
operated in one-to-one correspondence. The function does not apply to multiple operation or pole-change operation. Products to which the
auto-tuning method is applied do not need adjustment as in the case of V/f operation due to automatic control of the motor char acteristics.
Vector operation is carried out on the basis of the motor data read by the inverter, and operation is controlled instantaneousl y in accordance
with the load condition to continue optimal operation.
When the wiring distance between the motor and inverter becomes long (20 m or more), compensation may be necessary according tothe
drop in the line impedance. Select sufficiently thick cables when the wiring distance is long.
5. Output Torque Characteristics of Motor

Fig. D-47
Continuous operation characteristics when a general-purpose Technical
Total output/torque characteristics curve when AF motor and motor is driven by an inverter Information
SUMITOMO inverter are operated in combination
When a general-purpose motor is
Standards
(%) (%) driven by an inverter, the reduction
torque operation characteristics
Output Torque Torque curve 95~100 shown below will appear.
100 80~90
220V (440V)
Torque (%)
80 Output curve
100 AF motor 200V (400V)
50 General-purpose motor
40~60
50 35~45
20
0 6 60 120 6 20~30 60 120

Output frequency (Hz)
Output frequency (Hz)
Note: Constant torque operation is possible from 1 Hz when an axial
fan type is used.
6. Motor Temperature Rise

When a general-purpose motor is combined with an inverter for variable-speed operation, the motor temperature rise may be slightly greater
than if the motor is operated by a commercial power supply.
Possible causes are shown below :
Influence of output waveformUnlike a commercial power supply, the output waveform of an inverter is not a complete sine wave but includes
harmonics; therefore, motor damage will increase, raising the temperature slightly higher.
Decrease in motor cooling effect during slow-speed
operationA motor is cooled by its own fan. Therefore, when the motor speed is decreased by an inverter, the quantity of
cooling air decreases, reducing the cooling effect.
When a motor is to be operated at frequencies lower than the frequency of a commercial power supply, reduce the load torque tohold down
the temperature rise or use a special motor designed for inverter operation.
Hyponic
D-31
Constant Torque Operation of General-Purpose Motors

Operation with the following characteristics is possible when the HF-320 series inverter is used for sensorless control in comb ination
with general-purpose motors (3.7 kW or less).
A combination with a standard frame size motor can be used for constant torque operation where an AF motor with a reducer of a
larger frame size has conventionally been used.
Notes: 1. To select the combination with Hyponic®, examine the lubrication method and torque during slow speed operation and
rated output operation. Specify that inverter operation is desired when placing an order.
2. Consult factory for 400V class model to select insulation necessary for inverter operation.
3. When a brakemotor is operated for an extended period at slow speed, the cooling effect of the fan will decrease and the
brake temperature will rise substantially.
Consult factory for details.
4. Consult factory for details when a general-purpose motor will be operated under V/F control. (Also consult factory when using
the SF-320 series.)
Table D-41
Motor frame Frequency Series of
kW Insulation
size range inverter
0.1 F63S
0.2 F63M Class E
0.4 F71M
6~120Hz HF-320
0.75 F80M (Base frequency
60Hz)
Series
1.5 F90L
Class B
2.2 F100L
3.7 F112M
Fig. D-48 HF-320 Output Torque Characteristics during Operation in Sensorless Mode
200 Short time maximum torque 200 Short time maximum torque
150 150
Torque (%)
Torque (%)
Technical Continuous operation

Information Continuous operation
torque torque
100 100
Standards
80 80
50 50
40 40
0 6 20 40 60 120 0 6 20 40 60 120
Frequency (Hz) Frequency (Hz)
0.2~0.4kW 0.75~3.7kW
The combination-output torque presupposes that the rating is 100% when the motor frequency is 60 Hz. Use an AF motor when
constant torque is required at power exceeding 7.5 HP.
Hyponic
D-32
General
Engineering
Information
Basic Power Transmission Formulas
Derivations of Common Power Transmission Formulas
Conversion Factors
Technical
Information
Engineering
Hyponic
D-33
Power Transmission Formulas

Basic Mechanics
Basic Torque Formula Speed (Rotary to Linear)
T = Torque (inch pounds) V = Linear Velocity (ft/min)
T = F r F = Force (pounds) V = 0.262 N D N = Rotational Speed (RPM)
r = Radius (inches) D = Diameter (inch)
Horsepower (when Torque and Speed is known) Speed (Linear to Rotary)

HP = Horsepower N = Rotational Speed (RPM)
TN V
HP = T = Torque (inch pounds) N= V = Linear Velocity (ft/min)
63025 0.262 D
N = Rotational Speed (RPM) D = Diameter (inch)
Torque (when Horsepower and Speed is known) Torque to Accelerate Inertia

T = Torque (inch pounds) T A2 = Torque (inch pounds)
HP63025 WK2 ÐN WK2 = Inertia (poundinch2)
T= HP = Horsepower TA = ÐN = Speed Change (RPM)
N 3696 t
N = Rotational Speed (RPM) t = Time (seconds
Conveyors
Continuous Torque
T C = Continuous Torque (inlbs)
W = Weight (pounds)
T C = W(sinø + f cosø ) r ø = Incline Angle (degrees)
f = Friction Coefficient
r = Radius (inch)
Load Inertia at Pulley

WK2L = Load Inertia (lbin2) Friction Coefficient (f)
2 W= Weight (pounds) Belt/Rollers = 0.025
WK L = w r2
r= Radius (inch) Fabric/Steel = 0.27
Plastic/Steel = 0.35
Total Inertia to Accelerate Rubber/Steel = 0.50
WK2T = Total Inertia (lb in2) Leather/Steel = 0.56
2 WK L = Load Inertia (lbin )
2 2
2 2 2
WK L = WK L +WK D +WK M
WK D = Drive Inertia (lbin2)
2
OHL K-Factors
WK2M = Motor Inertia (lbin2) Chain = 1.0
Polychain = 1.25
Motor Torque Required
Pinion Gear = 1.25
T M = Motor Torque (inlb)
Technical TM = T C + TA V - Velt = 1.5
Information 1.5 R R e T C = Continuous Torque (inlb)
T A = Acceleration Torque (in lb) Flat Belt = 2.5
Engineering
TM ³ TC R R = Reduction Ratio
RR e e = Reducer Efficiency
Overhung Load
OHL = Overhung Load (pounds)
T K T= Torque (inch pounds)
OHL = r
K= OHL Factor
r= Radius (inch)
Solid Cylinder (Pulley) Inertia

WK2 = Load Inertia (lbin2)
WK2 = 1 w r2 W= Weight (pounds)
2
r= Radius
Hollow Cylinder Pulley Inertia

WK2 = Inertia (poundinch2)
w (r 12 + r 22) W= Weight (pounds)
WK2 =
2 r21 = Radius (inch)
r22 = Radius (inch)
Hyponic
D-34
Electrical[1]
Current (when Horsepower is known) Kilowatts
I = Current (A) kW = Power (kW)
HP 746 HP = Power (HP) I = Current (A)
I= E = Voltage (v) kW = 1.73 I E pf
1.73 E e pf e = Efficiency 1000 E = Voltage (v)
pf = Power Factor pf = Power Factor
Current (when kilowatts are known) Current (when kilowatts are known)
I = Current (A) HP = Power (HP)
I = kW 1000 kW = Power (kW) kW = Current (A)
1.73 E pf E = Voltage (v) HP = 1.73 I E e pf E = Voltage (v)
746
pf = Power Factor e = Efficiency
pf = Power Factor
Current (when kilovolt-amperes are known)
I = Current (A)
I = Kva 1000 Kva = Kilovolt-Amperes
1.73 E
E = Voltage (v)
Reducer Effect (Cyclo, Gear, Belt, or Chain Drive)

Speed Torque
N = Rotational Speed (RPM) T = Torque (inch pounds)
R R = Reuction Ratio TM = TL e = Reducer Efficiency
NM = NL R R
M = Motor e RR R R = Reduction Ratio
L = Load L = Load
Inertia
WK2 = Inertia (poundinch2)
2 e = Reducer Efficiency
WK L
WK 2 = 2 R R = Reduction Ratio
Wk M e RR
M = Motor
L = Load
COMMON RULES OF THUMB (APPROXIMATION):

At 1750 RPM, a motor develops 36 inchpounds of torque per horsepower under full motor load conditions. Technical
Information
At 1165 RPM, a motor develops 54 inchpounds of torque per horsepower under full motor load conditions.
Engineering
At 575 volts, a 3-phase motor draws 1 amp per horsepower under full motor load condition.
At 460 volts, 3-phase motor draws 1.25 amps per horsepower under full motor load condition.
At 230 volts, a 3-phase motor draws 2.5 amps per horsepower under full motor load condition.
Note: [1] All electrical formulas apply to Alternating Current, 3-phase motors only.
Hyponic
D-35
Formula Derivations
Velocity
ØD = Wheel Diameter = 2 R (ft, m)
R = Wheel Radius (ft, m)
N = Rotational Speed (RPM)
þ = 3.1416
V = þ 2 R N = 0.5236 R N (ft/min)
12
V = þ OD N (m/s)
60
Torque
R = Wheel Radius (in, m)
F = Load (lbs, N)
T = Torque = F R (in lbs, Nm)
Power F = Loads (lbs, N)

V = Velocity (ft/min, m/s)
HP = F V
33000
F V
kW =
1000
Power & Torque
Technical
Information
English Metric
Engineering
F V F V
HP = kW =
33000 1000
= F (0.5236 R N) substitute 0.5236 R N for V = 2 þ N

33000 1000 60 N F R substitute þ 2 R 60 for V
= F R N = N F R
63025 9550
= T N substitute T for F R = T N substitute T for F R

63025 9550
HP 63025 kW 9550
T= T=
N N
Power & Torque FA = M a FA = Acceleration Force (lbs, N)

= M V2-V1 V= Velocity (ft/sec, m/sec)
tA tA = Acceleration Time (sec)
\a = V2 - V1 M= Mass (slug, kg)
tA a= Acceleration (ft/sec2, m/sec2)
Hyponic
D-36
Common Conversion Factors

Length Volume
m dm cm mm m3 dm3 cm3 yd3
1m = 1 10 100 1000 1m 3
= 1 1000 1X10 6
1.3079
1 dm = 0.1 1 10 100 1 dm3 = 1X10 -3 1 1000 1.3X10-3
1 cm = 0.01 0.1 1 10 1 cm3 = 1X10 -6 1X10 -3 1 1.3X10-6
1 mm = 0.001 0.01 0.1 1 1 yd3 = 0.765 764.6 765X10 3 1
1 yd = 0.9144 9.144 91.44 914.4 1 ft3 = 28.3X10 -3 28.32 28.3X10 3 37X10 -3
1 ft = 0.3048 3.048 30.48 304.8 1 in3 = 16.4X10 -6 16.4X10 -3 16.39 21.4X10 -6
1 in. = 25.4X10 -3 0.2540 2.540 25.40 1 gal (UK) = 4.55X10 -3 4.546 4546 5.95X10 -3
1 mil = 25.4X10-6 254X10 -6 25.4X10 -3 25.4X10 -3 1 gal (US) = 3.79X10 -3 3.785 3785 4.95X10 -3
yd ft in mil yd3 in3 gal (UK) gal (US)

1m = 1.094 3.281 39.370 39.4X10 3
1m 3
= 35.32 61.02X10 3 220 264.2
1 dm = 0.1094 0.3281 3.937 3937 1 dm3 = 35.3X10 -3 61.02 0.22 0.2642
1 cm = 10.9X10-3 32.8X10 -3 0.3937 393.7 1 cm3 = 35.3X10 -6 61X10 -3 0.22X10 -3 0.26X10 -3
1mm = 1.09X10-3 3.28X10 -3 39.4X10 -3 39.37 1 yd3 = 27 46.7X10 3 168.2 202
1 yd = 1 3 36 36X103 1 ft3 = 1 1728 6.229 7.481
1 ft = 0.3333 1 12 12X103 1 in3 = 579X10 -6 1 3.6X10 -3 4.3X10 -3
1 in. = 27.8X10 -3 83.3X10 -3 1 1000 1 gal (UK) = 0.1605 277 1 1.201
1 mil = 27.8X10-6 83.3X10 -6 1X10 -3 1 1 gal (US) = 0.1337 231 0.8327 1
1 mile (statute or British mile) = 1760 yd = 5280 ft = 1609.344 m 1 bushel (UK) = 8 gal (UK) = 64 pt (UK) = 36.371
1 n mile (nautical mile) = 6080 ft = 1.853 km 1 bushel (US) = 0.969 bu (UK) = 35.24 l
1 km = 39370 in = 3281 ft = 1093.6 yd = 0.6214 mile 1 pint (UK) = 1/8 gal (UK) = 0.5682 l
= 0.5396 n mile 1 liq. pt. (US) = 1/8 gal (US) = 0.4732 l
1 fathom = 6 ft = 1.8288 m 1l = 1.76 pt (UK) = 2.113 liq. pt (US)
Area Force and Weight

m2
dm 2
cm 2
mm 2
N kP P
1 m2 = 1 100 10X103 1X10 6 1N = 1 0.1020 102.0
1 dm2 = 0.01 1 100 10X103 1 kp = 9.807 1 1000
1 cm2 = 0.1X10 -3 0.01 1 100 1p = 9.81X10-3 1X10 -3 1
1mm2 = 1X10 -6 0.1X10 -3 0.01 1 1 dyn = 1X10-5 1.02X10 -6 1.02X10 -3
1 yd2 = 0.8361 83.61 8361 836X10 3 1 tonf (UK) = 9964 1016 1.02X10 6
1 ft2 = 92.9X10 -3 9.290 929.03 92.9X10 3 1 lbf = 4.448 0.4536 453.6
1 in2 = 0.645x10-3 64.5X10 -3 6.4516 645.16 1 ozf = 28.4X10-3 28.35
1 CM = 5.07X10 -6 0.507X10 -3
dyn tonf (UK) lbf ozf
Technical
yd2 ft2 in2 CM 1N = 1X10 5 100.4X10 -6 0.2248 3.597 Information
1 kP = 981x103 0.984X10 -3 2.205 35.27
Engineering
1 m2 = 1.196 10.764 1550
1 dm2 = 12X10-3 0.1076 15.50 1P = 980.7 0.984X10 -6 2.2X10 -3 35.3X10 -3
1 cm2 = 0.12X10-3 1.08X10 -3 0.1550 197X10 3 1 dyn = 1 1X10-9 2.25X10 -6 36X10 -6
1 mm2 = 1.2X10-6 10.8X10 -6 1.55X10 -3 1.97X10 3 1 tonf (UK) = 996X10 6 1 2240 35.8X10 3
1 yd2 = 1 9 1296 1 lbf = 445X103 446X10 -6 1 16
1 ft2 = 0.1111 1 144 183X106 1 ozf = 27.8X103 27.9X10 -6 62.5X10 -3 1
1 in2 = 772X10-6 6.94X10 -3 1 1.27X106
1 CM = 5.45X10 -9 0.785X10 -6 1 1 (long) ton (UK) = 160 stones = 2240 lb = 1.016 t
1 (short) ton (US) = 142.9 stones = 2000 lb = 0.907 t
1 square mile = 640 acres = 2.590 km2 = 259 ha 1 stone = 14 lb = 224 oz = 6.35 kg
1 acre = 4840 yd2 = 0.405 ha = 4047 m2 1 ton = 20 cwt
1 km2 = 0.386 mi2 = 100 ha = 10000 a 1 cwt (UK) = 4 quarters = 8 stones = 112 lb
1 ha = 100 a = 2.471 acres = 11959.6 yd2 1 cwt (US) = 100 lb = 45.36 kg
1a = 100 m2 = 119.6 yd2 = 1076.4 ft2 1t = 1000 kg = 0.984 ton (UK) = 1.101 ton (US)
Hyponic
D-37
Common Conversion Factors

Velocity Moment of Inertia and Other Flywheel Effects
km/h m/min m/s kgm2(mr 2) kgfm2 (GD 2)
1 km/h = 1 16.667 0.2778 1 kgm (mr )
2 2
1 4
1 m/min = 0.06 1 16.7X10-3 1 kgfm2 (GD 2) 0.25 1
1 m/s = 3.6 60 1 1 lbfft2 (Wr 2) 42.1X10 -3 0.1686
1 mile/h = 1.609 26.82 0.4470 1 kpms2 9.807 39.23
1 ft/min = 18.3X10-3 0.3048 5.08X10 -3 1 ftlbfs2 1.356 5.423
1 ft/s = 1.097 18.288 0.3048
1 in/s = 91X10-3 1.524 25.4X10 -3
lbfft2 (Wr 2) kpms2 ftlbfs2
1 kgm2 (mr 2) 23.73 0.102 0.7376
mile/h ft/min ft/s in/s 1 kgfm2 (GD 2) 5.933 25.5X10 -3 0.1844
1 km/h = 0.6214 54.68 0.9113 10.936 1 lbfft2 (Wr 2) 1 4.30X10 -3 31.1X10 -3
1 m/min = 37.3X10-3 3.281 54.7x10-3 0.656 1 kpms2 232.7 1 7.233
1 m/s = 2.237 196.85 3.281 39.37 1 ftlbfs2 32.17 0.1383 1
1 mile/h = 1 88 1.467 17.6
1 ft/min = 11.4X10-3 1 16.7X10-3 0.2
1 ft/s = 0.6818 60 1 12 Pressure and Stress
1 in/s = 56.8X10-3 5 83.3X10 -3 1 N/m2 bar kgf/m2
1 N/m 2
= 1 1X10 -5
0.102
Torque 1 bar = 1X105 1 10.2X103
1 kgf/m2 = 9.81 98.1X10-6 1
Nm cNm kgfm 1 kgf/cm2 = 98.1X103 0.981 10X103
1 Nm = 1 100 0.10197 1 kgf/mm2 = 9.81X106 98.1 1X106
1 cNm = 0.01 1 1.02X10-3 1 lbf/yd2 = 5.32 53.2X10-6 0.543
1 kgfm = 9.8067 980.67 1 1 lbf/ft2 = 47.88 479X10-6 4.882
1 cpm = 98.1X10-6 9.81X10 -3 10X10 -6 1 lbf/in2 = 6.89X103 68.9X10 -3 703
1 lbfft = 1.356 135.6 0.1383 1 tonf/in2 = 15.4X103 154 1.58X10 6
1 lbfin = 0.1129 11.29 11.5X10-3
1 ozfin = 7.062X10-3 0.7062 0.72X10 -3
kgf/cm2 kgf/mm2 lbf/yd2
1 N/m 2
= 10.2x10 -6
0.102x10 -6
0.188
cpm lbfft lbfin ozfin 1 bar = 1.02 10.2X10-3 18.8X10 3
1 Nm = 10.2X103 0.73756 8.8507 141.61 1 kgf/m2 = 0.1X10-3 1X10 -6 1.843
1 cNm = 101.97 7.376X10-3 88.5X10 -3 1.4161 1 kgf/cm2 = 1 0.01 18.4X103
1 kgfm = 100X103 7.233 86.796 1389 1 kgf/mm2 = 100 1 1.84X106
1 cpm = 1 72.3X10-6 868X10 -6 13.9X10 -3 1 lbf/yd2 = 54X10-6 0.54X10 -6 1
1 lbfft = 13.8X103 1 12 192 1 lbf/ft2 = 0.488X10-3 4.88X10 -6 9
1 lbfin = 1152 83.3X10-3 1 16 1 lbf/in2 = 70.3X10-3 0.703X10 -3 1296
1 ozfin = 72.01 5.21X10-3 62.5X10 -3 1 1 tonf/in2 = 157.5 1.575 2.9X106
Technical
Information Power lbf/ft2 lbf/in2 tonf/in2
Engineering
kW PS hp 1 N/m 2
= 20.88X10 -3
145X10 -6
64.75X10 -9
1 kW = 1 1.360 1.341 1 bar = 2.088X103 14.5 6.475X10 -3
1 PS = 0.7355 1 0.9863 1 kgf/m2 = 0.2048 1.42X10-3 0.64X10 -6
1 hp = 0.7457 1.014 1 1 kgf/cm2 = 2.05X103 14.223 6.4X10 -3
1 kgfm/s = 9.81X10-3 13.33X10 -3 13.15X10 -3 1 kgf/mm2 = 205X103 1.422X10 3 0.6349
1 ftlbf/s = 1.36X10-3 1.84X10 -3 1.82X10 -3 1 lbf/yd2 = 0.1111 772X10-6 0.345X10 -6
1 kcal/s = 4.1868 5.692 5.615 1 lbf/ft2 = 1 6.94X10-3 3.1X10 -6
1 Btu/s = 1.055 1.435 1.415 1 lbf/in2 = 144 1 0.446X10-3
1 tonf/in2 = 0.323X106 2240 1
kgfm/s ftlbf/s kcal/s Btu/s

1 kW = 102.0 737.6 0.2388 0.9478
1 PS = 75 542.5 0.1757 0.6971
1 hp = 76.04 550 0.1781 0.7068
1 kgfm/s = 1 7.233 2.342X10-3 9.295X10 -3
1 ftlbf/s = 0.1383 1 0.324X10-3 1.285X10 -3
1 kcal/s = 426.9 3088 1 3.968
1 Btu/s = 107.6 778.2 0.2520 1
Hyponic
D-38
Bottling/Baking Water Treatment
Steel hypoid gear technology, Each of these

maintenance-free grease lubrication Sumitomo Paramax®
and a compact modular housing speed reducers helps
makes the Hyponic® an efficient performer A 15-hp Beier mechanical variable speed drive pump up to 13 million
in the food industry. with electric remote control provides gallons a day at this
an adjustable, steady speed range state-of-the-art waste-
for this 350-ft. oven band conveyor. water treatment facility
Cyclo® mixer drives are a key compo-
in the City of Clearwater,
nent of this award-winning water
Florida.
treatment facility in Hillsborough
County, Florida.
Material Handling Custom Designs
In less than 20 minutes,

Sumitomo Paramax® reducers 96 Sumitomo Cyclo® Bevel Buddybox
provide quiet, reliable opera- gearmotors help retract
tion for both the hoist and trol- the 13,000-ton roof on Seattle’s
ley drive systems in this 35-ton new Safeco Field.
capacity DC Trolley Hoist used
for heavy-duty coil handling The Sumitomo gearmotors, on eight travel
service. truck assemblies, turn 128 36” wheels.
Steel
Wood Products
Sumitomo Cyclo® drives are an inte-
gral part of this manufacturing
plant which produces 150,000 board
feet of unfinished strip and plank
hardwood flooring each week. Once flooring is side-matched, it is inspected for defects. This After molten steel is formed in the five-strand continuous caster
conveyor, driven by Sumitomo Cyclo® drives, carries defective at this steel mill, it is conveyed by Sumitomo Cyclo® drives on the auto-
material to the hammer mill. torch conveyors where the steel is cut into billets.
WORLDWIDE LOCATIONS
Sumitomo Machinery Corporation of

America
Headquarters & Manufacturing
4200 Holland Boulevard

Chesapeake, VA 23323
Tel: 757-485-3355 • Fax: 757-485-3075
E-mail: [email protected]
U.S. Sales and Support Mexico Europe

Mid-West Monterrey Austria
Sumitomo Machinery Corporation of America SM-Cyclo de Mexico, S.A. de C.V. Belgium
175 West Lake Drive Calle “C” No. 506A
Glendale Heights, IL 60139 Parque Industrial Almacentro France
Tel: 630-752-0200 • Fax: 630-752-0208 Apodaca, N.L., Mexico 66600 Germany
Tel: 011-52-81-8369-3697/8 • Fax: 011-52-81-8369-3699
Italy
West
Sumitomo Machinery Corporation of America Netherlands
2375 Railroad Street South America Spain
Corona, CA 92880-5411
Tel: 909-340-4100 • Fax: 909-340-4108 Brazil Sweden
SM-Cyclo Redutores do Brasil Ltda.
Av. Fagundes Filho, 191 Switzerland
Southwest Ed. Houston Office Center–c j. H123
Sumitomo Machinery Corporation of America CEP: 04304-010–São Paulo, Brazil
1420 Halsey Way #130 Tel: 011-55-11-5585-3600 • Fax: 011-55-11-5585-9990 Asia
Carrollton, TX 75007
Tel: 972-323-9600 • Fax: 972-323-9308 China
Chile Hong Kong
SM-Cyclo de Chile Ltda.
San Pablo N. 3507 Indonesia
Canada Comuna de Quinta Normal - Santiago, Chile Korea
Tel: 011-562-786-6963 • Fax: 011-562-786-6964
Toronto (East) Malaysia
SM-Cyclo of Canada, Ltd.
870 Equestrian Court Argentina Philippines
Oakville, Ontario, Canada L6L 6L7 SM-Cyclo de Argentina SA Taiwan
Tel: 905-469-1050 • Fax: 905-469-1055 Manuel Montes de Oca 6719
B1606 BMG, Munro Thailand
Buenos Aires, Argentina
Vancouver (West)
Tel: 011-54-11-4765-5332 • Fax: 011-54-11-4765-5517
SM-Cyclo of Canada, Ltd.
740 Chester Road, Annacis Island, Delta Other Locations
B.C., Canada V3M 6J1 Australia
Tel: 604-525-5403 • Fax: 604-525-0879
India
Montreal New Zealand
SM-Cyclo of Canada, Ltd. South Africa
226 Migneron Street
St. Laurent, Quebec, Canada H4T 1Y7
Tel: 514-340-1300 • Fax: 514-340-1343
World Headquarters
Japan
Sumitomo Heavy Industries, Ltd.
Power Transmission & Controls Group
5-9-11, KITA-Shinagawa, Shinagawa-Ku
Tokyo 141-8686 Japan
Tel: 011-813-5488-8363 • Fax: 011-813-5488-8365
For Worldwide contact information:


Hyponic-003 COMPLETE CATALOG

Uploaded by

Copyright:

Available Formats

Hyponic-003 COMPLETE CATALOG

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Hyponic-003 COMPLETE CATALOG

Uploaded by

Copyright:

Available Formats

Hyponic®

Hypoid Right Angle

Sumitomo’s patented Hyponics are

Patented Compact Design: 80

More Torque Delivered 70

Two-Year Warranty Hyponic hypoid gearing demonstrates efficiencies of

TABLE 1 HYPONIC PRODUCT CODE TABLE 7 MODEL SIZE

F Flange (Solid Shaft)

SUFFIX OUTPUT SHAFT INPUT

TABLE 10 AGMA CLASS (Integral Motor Type Only)

SUFFIX SPECIFICATION STANDARD RATIOS

SG Single Phase Motor 7 25 80 240 750

Three Phase Motor 10 30 100 300 900

SUFFIX SPECIFICATION NOMENCLATURE EXAMPLES:

Plug-in Shaft with Extended Flange

P1 Left (Viewed from

Q1 Right (Viewed from

TABLE 13 BRAKE (Gearmotor Only)

Table 15 Recommended Reducer Service Factors

PRIME MOVER DURATION OF SERVICE UNIFORM MODERATE SHOCK HEAVY SHOCK

AGMA AGMA AGMA

Occasional 1/2 hr. per day *0.50 *0.80 1.25

Intermittent 3 hrs. per day *0.80 1.00 1.50

24 hours per day 1.25 1.50 2.00

Excessive Overloads example, coupling connections normally involve torsional forces

Thermal Capacity All dimensions in this catalog are for reference

5 HP Frame Size 63, Bore: Ø2.00²

Frame Size: 1430, Bore: Ø1.375²

Frame Size: 56, Bore: Ø1.50² [3]

Frame Size: 1531,

Frame Size: 1330, Bore: Ø1.25²

Capacitor-Starting, Capacitor-Run Capacitor-Starting, Capacitor-Run

Mounting Direction of Terminal Box

Gearmotor Selection Flowchart

DETERMINE TYPE OF DRIVEN MACHINE

CHECK HOURS OF OPERATION

CHOOSE A LOAD CLASSIFICATION See Load Classification Tables, Pages A-7~8

SELECT MOUNTING STYLE

FINALIZE REQUIRED OPTIONS See Standard Specifications, Page A-4

Gearmotor Selection Procedure

1. Application  Type of Driven Machine Example: Belt Conveyor  Uniformly Fed

or Fed, Belt, Up to 10 hours per day, the recommended minimum is Class I.

To check overhung load use this formula: HP: Transmitted or Motor HP

AGMA Load Classifications

Table A-3 Load Classification Listed By Industry [2]

Class Class Class Class

AGMA Load Classifications

Class Class Class Class

Tire Building Machines Refer to Factory

Reversing  III Openers

Light (Small Diameter) I II Tubers & Strainers II II

Motor Thermal Ratings

(2) Obtain the Z value (number of starts per hour).

(3) Calculate C multiplied by Z.

Selection Tables  60 Hz, 3-Phase, 1750 RPM

1.07 I 275 01 1120YA 50

1.07 I 395 01 1230YA 80

1.07 I 395 01 1230YA 100

1.07 I 405 01 1230YA 120

Occasional 1/2 hr. per day 0.50 0.80 1.25

1. Application Type of Driven Machine Example: Belt Conveyor Uniformly Fed

Reversing III Openers

Selection Tables 60 Hz, 3-Phase, 1750 RPM

Selection Tables 60 Hz, 3-Phase, 1750 RPM, cont.

Selection Tables 60 Hz, 3-Phase, 1750 RPM

Selection Tables 60 Hz, 3-Phase, 1750 RPM, cont.

1/2 HP (0.4 kW) cont.

Selection Tables 60 Hz, 3-Phase, 1750 RPM

Selection Tables 60 Hz, 3-Phase, 1750 RPM, cont.

1 HP (0.75 kW) cont.

Selection Tables 60 Hz, 3-Phase, 1750 RPM

Selection Tables 60 Hz, 3-Phase, 1750 RPM, cont.

Selection Tables 60 Hz, Single Phase, 1750 RPM, cont.

Selection Tables Inverter Duty

Selection Tables Inverter Duty, cont.