D3G355-GG03-01 EC centrifugal fan - RadiFit

backward-curved, dual-intake
with housing (flange)

ebm-papst Mulfingen GmbH & Co. KG

Bachmühle 2 · D-74673 Mulfingen
Phone +49 7938 81-0
Fax +49 7938 81-110
info1@de.ebmpapst.com
www.ebmpapst.com
Limited partnership · Headquarters Mulfingen
Amtsgericht (court of registration) Stuttgart · HRA 590344

General partner Elektrobau Mulfingen GmbH · Headquarters Mulfingen

Amtsgericht (court of registration) Stuttgart · HRB 590142

Nominal data

Type D3G355-GG03-01
Motor M3G112-IA

Phase 3~
Nominal voltage VAC 400
Nominal voltage range VAC 380 .. 480
Frequency Hz 50/60

Method of obtaining data ml

Speed (rpm) min-1 2600
Power consumption W 3160
Current draw A 4.9
Min. ambient temperature °C -25
Max. ambient temperature °C 40
ml = Max. load · me = Max. efficiency · fa = Free air · cs = Customer specification · ce = Customer equipment
Subject to change

Data according to ErP Directive

Actual Req. 2015

01 Overall efficiency ηes % 65.1 55.5 09 Power consumption Ped kW 3

02 Measurement category A 09 Air flow qv m³/h 6105
03 Efficiency category Static 09 Pressure increase pfs Pa 1085
04 Efficiency grade N 70.6 61 10 Speed (rpm) n min-1 2600
05 Variable speed drive Yes 11 Specific ratio* 1.01
*
Data obtained at optimum efficiency level. Specific ratio = 1 + pfs / 100 000 Pa LU-167206
The ErP data is determined using a motor-impeller combination in a standardized measurement setup.

Item no. 54191-5-9980 · ENU · Change 88833 · Approved 2016-06-22 · Page 1 / 5

ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · info1@de.ebmpapst.com · www.ebmpapst.com
 D3G355-GG03-01 EC centrifugal fan - RadiFit
backward-curved, dual-intake
with housing (flange)

Technical description

Weight 37 kg
Fan size 355 mm
Rotor surface Painted black
Electronics housing material Die-cast aluminum
Impeller material Sheet aluminum
Housing material Sheet steel, galvanized
Motor suspension Motor mounted with brackets on one side
Direction of rotation Clockwise, viewed toward rotor
Degree of protection IP54
Insulation class "F"
Moisture (F) / Environmental (H) F3-1
protection class
Max. permitted ambient temp. +85 °C
for motor (transport/storage)
Min. permitted ambient temp. for -40 °C
motor (transport/storage)
Installation position Shaft horizontal or rotor on bottom; rotor on top on request
Condensation drainage holes On rotor side
Mode S1
Motor bearing Ball bearing
Technical features - Output 10 VDC, max. 10 mA
- Operation and alarm display
- External 24 V input (parameter setting)
- Alarm relay
- Integrated PID controller
- Power limit
- Motor current limitation
- PFC, passive
- RS-485 MODBUS-RTU
- Soft start
- EEPROM write cycles: 100,000 maximum
- Control input 0-10 VDC / PWM
- Control interface with SELV potential safely disconnected from supply
- Temperature derating
- Thermal overload protection for electronics/motor
- Line undervoltage / phase failure detection
EMC immunity to interference According to EN 61000-6-2 (industrial environment)
EMC interference emission According to EN 61000-6-3 (household environment), except EN 61000-3-2 for
professionally used equipment with a total rated power greater than 1 kW
Touch current according to IEC <= 3.5 mA
60990 (measuring circuit Fig. 4,
TN system)
Electrical hookup Via terminal box
Motor protection Thermal overload protector (TOP) internally connected
With cable Variable
Pollution degree 3
Protection class I (with customer connection of protective earth)
Conformity with standards CE
Comment Conformity with EN 61800-5-1 and EN 60335-1 in preparation

Item no. 54191-5-9980 · ENU · Change 88833 · Approved 2016-06-22 · Page 2 / 5

ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · info1@de.ebmpapst.com · www.ebmpapst.com
 D3G355-GG03-01 EC centrifugal fan - RadiFit
backward-curved, dual-intake
with housing (flange)

Product drawing

1 Tightening torque 3 ± 0.5 Nm

2.1 NC
2.2 COM
2.3 +10 V
2.4 0-10 V
2.5 GND
2.6 RSA
2.7 RSB
2.8 L1
2.9 L2
2.10 L3
3 Cable diameter min. 8 mm, max. 12 mm, tightening torque 2.5 ± 0.4 Nm

Item no. 54191-5-9980 · ENU · Change 88833 · Approved 2016-06-22 · Page 3 / 5

ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · info1@de.ebmpapst.com · www.ebmpapst.com
 D3G355-GG03-01 EC centrifugal fan - RadiFit
backward-curved, dual-intake
with housing (flange)

Connection diagram

No. Conn. Designation Color Function/assignment

1 1, 2 PE green/yellow Protective earth
1 3, 4, 5 L1, L2, L3 black Power supply 50 / 60 Hz
1 6 NC white 1 Status relay, floating status contact, break for failure; contact rating 250 VAC / 2 A (AC1) / min.
10 mA,

reinforced insulation on supply side and basic insulation on control interface side (or
reinforced insulation on control interface side up to 250 VAC potential difference)
1 7 COM white 2 Status relay, floating status contact, break for failure; contact rating 250 VAC / 2 A (AC1) / min.
10 mA,

reinforced insulation on supply side and basic insulation on control interface side (or
reinforced insulation on control interface side up to 250 VAC potential difference)
2 9 +10 V red Fixed voltage output 10 VDC, SELV, +10 V ±3%, max. 10 mA, short-circuit-proof, power
supply for external devices (e.g. pot);
fixed voltage input 24 VDC for setting parameters via MODBUS without line voltage supply
2 10 0-10 V yellow Analog input (set value) SELV, 0-10 V, Ri = 100 kΩ, adjustable curve
2 11 RSA white RS485 interface for MODBUS, RSA; SELV
2 12 RSB brown RS485 interface for MODBUS, RSB; SELV
2 13 GND blue Reference ground for control interface, SELV

Item no. 54191-5-9980 · ENU · Change 88833 · Approved 2016-06-22 · Page 4 / 5

ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · info1@de.ebmpapst.com · www.ebmpapst.com
 D3G355-GG03-01 EC centrifugal fan - RadiFit
backward-curved, dual-intake
with housing (flange)

Curves: Air performance 50 Hz

in wg
Pa

ρ = 1.15 kg/m³ ± 2 %
Measurement: LU-174904-1
5

1200
Air performance measured according to ISO
4 5801 installation category A. For detailed
information on the measurement setup,
contact ebm-papst. Intake sound level:
Sound power level according to ISO 13347 /
4

sound pressure level measured at 1 m

distance from fan axis. The values given are
valid under the specified measuring
8 conditions and may vary due to conditions of
800 installation. For deviations from the standard
configuration, the parameters have to be
3 checked on the installed unit.
3

12 7
2

400 11 2
16
6
15
1

10
14

0 1000 2000 3000

13
4000
9
5000 6000
5 1 cfm
Pfs

qv 2000 4000 6000 8000 10000 m³/h

Measured values
Wired U f n Ped I LpAin LwAin LwAout qv pfs qv pfs
V Hz min-1 W A dB(A) dB(A) dB(A) m3/h Pa CFM inH2O
1 Y 400 50 2600 2979 4.59 82 95 100 12035 0 7085 0.00
2 Y 400 50 2600 3160 4.90 80 93 97 10230 400 6020 1.61
3 Y 400 50 2600 3160 4.90 78 91 95 8035 750 4730 3.01
4 Y 400 50 2600 3040 4.68 76 89 93 5970 1100 3515 4.42
5 Y 400 50 2300 2029 3.13 78 92 97 10590 0 6235 0.00
6 Y 400 50 2300 2200 3.39 77 90 94 9065 318 5335 1.28
7 Y 400 50 2300 2163 3.33 75 87 92 7070 583 4160 2.34
8 Y 400 50 2300 2069 3.18 73 86 90 5250 858 3090 3.44
9 Y 400 50 1900 1144 1.76 74 87 92 8750 0 5150 0.00
10 Y 400 50 1900 1240 1.91 72 85 89 7490 217 4405 0.87
11 Y 400 50 1900 1219 1.88 70 83 87 5840 398 3435 1.60
12 Y 400 50 1900 1166 1.80 68 81 85 4340 586 2555 2.35
13 Y 400 50 1500 563 0.87 68 81 86 6905 0 4065 0.00
14 Y 400 50 1500 610 0.94 66 79 83 5910 135 3480 0.54
15 Y 400 50 1500 600 0.92 64 77 81 4610 248 2715 1.00
16 Y 400 50 1500 574 0.88 62 75 79 3425 365 2015 1.47
Wired = Wiring · U = Power supply · f = Frequency · n = Speed (rpm) · Ped = Power consumption · I = Current draw · LpAin = Sound pressure level intake side · LwAin = Sound power level intake side
LwAout = Sound power level outlet side · qv = Air flow · pfs = Pressure increase

Item no. 54191-5-9980 · ENU · Change 88833 · Approved 2016-06-22 · Page 5 / 5

ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · info1@de.ebmpapst.com · www.ebmpapst.com