Railway Planning

Download as pdf or txt
Download as pdf or txt
You are on page 1of 30

MODULE 1

RAILWAY PLANNING

SIGNIFICANCE OF ROAD, RAIL, AIR AND WATER TRANSPORTS –


COORDINATION OF ALL MODES TO ACHIEVE SUSTAINABILITY.
RAIL TRANSPORT

Political Advantages:

1. Railways have united the people of different castes, religions customs and traditions.
2. Railways have contributed towards development of a national mentality in the minds
of people.
3. Railway have helped in the mass migration of the population.
4. Only due to effective country wide network of railways, the central government
administration has become easy & effective.

Cultural & Social aspects:

1. Railway has made it easier to reach places of religious importance.

2. Railway provide a convenient & safe mode of transport for the country.

3. During travel as people of different caste & religions sit together the interaction is
developed.

Economical aspects:

1. Due to railway industrial development in for off places is possible, increasing the land
values & standard of living of the people.

2. Mobility of labor has contributed to industrial development.

3. During famines, railways have played the vital role in transporting food & clothing to
the affected areas.

4. Commercial farming is very much helped by the railway network throughout the
country.
ROAD TRANSPORT

• Owing to flexibility of operation and the ability to provide door-to-door service, road
transport is ideally suited for carrying light commodities and a small number of
passengers over short distances.

• The importance of roads in connecting the vast rural areas of India to form the national
market and economy cannot be overstated.

• Connectivity provided by roads is perhaps the single most important determinant of


well-being and the quality of life of people living in an urban area.

AIR TRANSPORT

• Owing to the heavy expenditure on the sophisticated equipment required and the high
fuel costs, air transport is better suited for carrying passengers or goods that have to
reach their destinations in a very short period of time.

• Air transport is an integral part of transport infrastructure and a significant sector of the
economy. Airports are recognized for their ability to multiply business activity in their
proximity and development.

WATER TRANSPORT

• Owing to low cost of infrastructure and relatively slow speeds, water transport is best
suited for carrying heavy and bulky goods over long distances, provided there is no
consideration of the time factor.

• Water transport is the cheapest and the oldest mode of transport.

• It operates on a natural track and hence does not require huge capital investment in the
construction and maintenance of its track except in case of canals.

• The cost of operation of water transport is also very less. It has the largest carrying
capacity and is most suitable for carrying bulky goods over long distances.
RAILWAY TRACK (PERMANENT WAY)
Definition: The combination of rails, fitted on sleepers and resting on ballast & sub grade
is called the railway track or permanent way.

In a permanent way, the rails joined in series by fish plates & bolts and then they are fixed
to sleepers by different types of fastenings. The sleepers properly spaced & boxed with
ballast.

The layers of ballast rest on the prepared sub grade called the formation.

ELEMENTS OF PERMANENT WAY

1.Rails: - Rails are steel girders over which the train moves and transmit the wheel loads
of train to the sleepers below.

2. Sleepers: - The sleepers hold the rails in proper position and provide a correct gauge
with the help of fittings and fastenings and transmit the train load to the ballast below.

3.Ballast: - The ballast distributes the load over the formation and holds the sleepers in
position and provides a uniform level surface.

4.Fittings and fastenings: - They provide a grip between rails and sleepers. The rails are
joined to each other by fish plates and the rails are fastened to the sleepers with the help of
various fitting such as spikes and keys.
5.Formation: - Formation is the base of a track. It gives a level surface where the ballast
rests. It takes the total load of the track and the train moving on it.

Requirement of an Ideal Permanent way

Requirement of an ideal permanent way so as to achieve higher speed & better riding
qualities with less future maintenance.

▪ The gauge should be correct & uniform.

▪ The rails should be in proper level. In a straight track, two rails must be at the same
level.

▪ The alignment should be correct, i.e., should be free from kinks or irregularities.

▪ The gradient should be uniform & as gentle as possible.

▪ There should be adequate provisions for easy renewals & replacement.

▪ The track should be resilient & elastic in order to absorb shocks & vibrations of running
track.

▪ The radii & super elevation on cures should be properly designed & maintained.

▪ Drainage system must be perfect for enhancing safety & durability of track.

▪ The various components of the track, i.e., the rails, fittings, sleepers, ballast &
formation must fully satisfy the requirements for which they have been provided.
▪ The track structure should be strong low in initial cost as well as, maintenance cost.

Basic requirements of good Alignment

➢ Length of track should be as short as possible.


➢ The initial construction cost should be minimum.
➢ Maintenance cost should be minimum.
➢ It should have easy gradients so that locomotives can carry more load and the transport
charges may be minimum.
➢ It should have easy curves.
➢ It should give maximum safety to the passengers without any chance of accidents or
derailment.
➢ It should pass through important cities and industrial areas.
➢ It should pass through aesthetic areas so that passengers may enjoy their journey

RAILS

Requirements of Rails

1. They should be of proper composition of steel and should be manufactured by open


fireplace or duplex process.

2. The vertical stiffness should be high enough to transmit the load to several sleepers’
underneath. The height of rail should therefore adequate.

3. Rails should be capable of withstanding lateral forces. Large width of head and foot
endows the rails with high lateral stiffness.
4. The head must be sufficiently deep to allow for an adequate margin of vertical wear.
The wearing surface should be hard.
5. Web of rails should be sufficiently thick to bear the load coming on it and should
provide adequate flexural rigidity.
6. Foot should be wide enough so that rails are stable against overturning especially on
curves.
7. Bottom of the head and top of the foot of rails should be so shaped as to enable the fish
plates to transmit the vertical load efficiently from the head to the foot at rail joints.
The rails used in the construction of railway track are of following types:

• Double headed rails (D.H Rails)

• Bull headed rails (B.H Rails)

• Flat footed rails (F.F Rails)

Double headed rails

• The rail sections, whose foot and head are of same dimensions, are called Double
headed or Dumb-bell rails.

• In the beginning, these rails were widely used in the railway track.

• The idea behind using these rails was that when the head had worn out due to rubbing
action of wheels, the rails could be inverted and reused.

• But by experience it was found that their foot could not be used as running surface
because it also got corrugated under the impact of wheel loads.

• This type of rail is not in use in Indian Railways now-a day.

Bull headed rail

• The rail section whose head dimensions are more than that of their foot are called bull
headed rails.

• In this type of rail, the head is made little thicker and stronger than the lower part by
adding more metal to it.

• These rails also require chairs for holding them in position.

• Bull headed rails are especially used for making points and crossings.

Flat footed rail

• The rail sections having their foot rolled to flat are called flat footed or vignole`s rails.
This type of rail was invented by Charles Vignole in 1836.

• It was initially thought that the flat-footed rails could by fixed directly to wooden
sleepers and would eliminate chairs and keys required for the B.H. rails.

• But later on, it was observed that heavy train loads caused the foot of the rail to sink
into the sleepers and making the spikes loose.
• To remove this defect, steel bearing plates were used in between flat footed rails and
the wooden sleeper. These rails are most commonly used in India.

Double headed rails Bull headed rails Flat footed rails

SLEEPERS

Sleepers are members generally laid transverse to the rails on which the rails are supported and
fixed, to transfer the loads from rails to the ballast and subgrade below.

Functions of sleepers
1. To hold the rails to correct gauge.

2. To hold the rails in proper level or transverse tilt so as to provide a firm and even
supports to rails.

3. To act as an elastic medium in between the ballast and rails to absorb the blows and
vibrations of moving loads.

4. Sleepers also add to the longitudinal and lateral stability of the permanent track on the
whole.

5. They also provide means to rectify track geometry during service life.

Requirements of sleepers

1. The sleepers to be used should be economical i.e., they should have minimum possible
initial and maintenance costs.

2. The fittings of the sleepers should be such that they can easily adjusted during
maintenance operation such as easy lifting, packing, removal and replacement.

3. The design of the sleepers should not be such that gauge, alignment of track and levels
of the rails can be easily adjusted and maintained.
4. The weight of the sleepers should not be too heavy or excessively light.

5. The sleeper design and spacing should be such as to facilitate easy removal and
replacement of ballast.

6. The design of sleepers should be such that they are not damaged during packing
processes.

7. An ideal sleeper should also have an anti – Sabotage and anti – theft qualities.

Classification of Sleepers
Sleepers can be classified according to materials used in their construction in the following
categories:
1. Timber or Wooden Sleepers
2. Metal Sleepers
a. Cast iron sleepers
b. Steel sleepers
3. Concrete Sleepers
a. Reinforced concrete sleepers
b. Prestressed concrete sleepers
1. Wooden Sleepers: wooden sleepers are regarded to be the best as they fulfil almost all
the requirements of an ideal sleeper. The life of the timber sleepers depends upon their
ability to resist Wear, Decay, Attack by vermin and Quality of timber used. Following
are the advantages and disadvantages of using wooden sleepers.
Advantages:
➢ Timber is easily available in all parts of India.
➢ Fittings for wooden sleepers are few and simple in design.
➢ These sleepers are able to resist the shocks and vibration due to heavy moving
loads and also give less noisy attack.
➢ These wooden sleepers are suitable for all types of ballast.
Disadvantages:
➢ These sleepers are subjected to wear, decay, attack by white ants, warping,
cracking, end splitting, rail cutting etc.
➢ It is difficult to maintain gauge in the case of wooden sleepers.
➢ Track is easily disturbed, i.e., alignment maintenance is difficult.
➢ Wooden sleepers have got minimum service life (12-15 years) as compared to
other types.
➢ Maintenance cost of wooden sleepers is highest as compared to other types.

2. Metal Sleepers: Due to growing scarcity of wooden sleepers, high cost and short life
metal sleepers were being used. • Metal sleepers are either of cast-iron or steel. Cast-
iron is in greater use because of its resistance to corrosion.
Advantages
➢ Metal sleepers are uniform in strength and durability.
➢ In metal sleepers, the performance of fittings is better and hence lesser creep
occurs.
➢ Metal sleepers are economical as life is longer and maintenance is easier.
➢ Gauge can be easily adjusted and maintained.
➢ Frequent renewal is not required.
➢ Have good scrap value, easy to manufacture and not susceptible to fire hazards.
Disadvantages
➢ More ballast is required than other types of sleepers.
➢ Fittings required are greater in number and difficult to maintain/inspect.
➢ They are liable to rusting/corrosion.
➢ Metal being good conductor of electricity interferes with track circuiting.
➢ They are unsuitable for bridges, level crossings and in case of points and
crossings.
➢ These are only suitable for stone ballast and for rails which they are
manufactured.

3. Concrete Sleepers: These are made of strong homogenous material, impervious to


effects of moisture, and is unaffected by the chemical attack of atmospheric gases or
subsoil salts. These can easily be moulded to size and shape required to withstand
stresses produced by fast and heavy traffic.
Advantages
➢ These are free from natural decay and attack by vermin etc.
➢ They have maximum life as compared to others (40-60 years)
➢ These are not affected by moisture, chemical action of ballast and subsoil salts.
➢ There is no difficulty in track circuiting of electrified tracks.
➢ Increased weight helps to reduces joint maintenance, greater stability of track
and better resistance against temperature variation.
Disadvantages
➢ The weight of concrete sleeper is as high as 2.5 to 3 times of wooden sleeper,
requiring the mechanical appliances for handling.
➢ These require pads and plugs for spikes.
➢ They damage the bottom edge during packing.
➢ The scrap value is almost nil.
➢ The damages to the concrete sleepers are very heavy in case of derailment.

BALLAST
➢ It is a layer of broken stone, gravel, moorum or any other gritty material placed &
packed below & around sleepers for distributing the load from the sleepers to the
formation & for providing drainage as well as giving longitudinal & lateral stability to
the track.
➢ It provides a suitable foundation for the sleepers and also hold the sleepers in their
correct level and position, preventing their displacement by lateral or longitudinal
thrusts.
➢ The lateral stability of track depends on the ballast.
Functions of ballast
• It provides levelled bed or support for the railway sleepers.
• It transfers the load from sleepers to subgrade and distributes the load uniformly on
subgrade.
• It holds the sleepers in a firm position while the trains pass by.
• It prevents the longitudinal and lateral movement of sleepers.
• It offers good drainage to the track
Requirements of the good ballast
• It should be tough and wear resistant.
• It should be hard so that it does not get crushed under the moving loads.
• It should be generally cubical with sharp edges.
• It should be non-porous and should not absorb water.
• It should resist both attrition and abrasion.
• It should be durable and should not get pulverized or disintegrated under adverse weather
conditions.
• It should allow for good drainage of water. • It should be cheap and economical.
• It should not make the track dusty or muddy due powder under dynamic wheel loads but
should be capable of being cleaned to provide good drainage.
• It should not produce any chemical action in rail and metal sleepers
• The size of stone ballast should be 5cm for wooden sleepers, 4cm for metal sleepers
and 2.5cm for turnouts and crossovers.
Types of Ballast
1. Broken stone Ballast: Broken stone is widely used ballast in railways. It is obtained by
crushing hard stones like granite, hard trap, quartzite etc. In lieu of broken stones,
limestone and sandstone can also be used. It is suitable for high-speed railway tracks.
The broken stone selected as ballast should be hard, tough and non-porous. It should
stay strong against inclement weather conditions.
Benefits of Broken Stone Ballast
• Broken stones are hard, tough and durable.
• Hold the sleepers in a strong position and provide stability to the track.
• Suitable for heavy traffic tracks and for high-speed track.

Drawbacks of Broken Stone Ballast

• Since broken stones are not easily available, their initial cost is a little high.

• Produce noise when the train is moving on the track.

• They are sharp and angular and hence wooden sleepers may be liable to damage by
these broken stones.
2. Sand Ballast: Sand can also be used as a ballast material. It is well suitable under cast
iron sleepers and can be seen in desert railway tracks where plenty of sand gets accr
used on the track. Coarse sand is best suitable as ballast than fine sand.
Benefits of Sand Ballast
• It provides excellent drainage facilities to the track.
• Well suitable for Cast iron sleepers and does not produce any noise while the train is
moving on track.
• Cheap and abundantly available material.
Drawbacks of Sand Ballast
• Sand may blow off easily due to vibrations produced by train or due to high winds. So,
a frequent renewal is required.
• Excessive wear of sleepers and moving parts can occur due to friction developed by
sand.
3. Gravel Ballast: Gravel is a naturally occurring material formed by the erosion of rocks.

They are suitable for all types of sleepers and are usually round and smooth and can be

obtained from river beds, gravel pits etc.

Benefits of Gravel Ballast


• It occurs naturally and hence is cheap and easily available.
• Properly cleaned gravel offers excellent drainage facilities to the
track.
• Well packed gravel requires less maintenance and has high durability.

Drawbacks of Gravel Ballast


• Because of their smoothness and roundness, they may get separated from the
bed under vibrations.
• Since it occurs naturally, it may contain some amount of earth or clay which
should be cleaned. If not cleaned, the drainage properties of gravel may get
affected.
• Sieving should be done to eliminate small size gravel particles otherwise they
may affect the drainage properties.
• Produce noise when the train is moving on the track.

4. Moorum Ballast: Moorum is formed by the decomposition of laterite. It is available


mostly in red colour and, sometimes, in yellow. If the track is to be laid on black cotton
soil, moorum can be used as a blanketing material or sub-ballast since it prevents
permeability of water into the subgrade or formation. Moorum is good as sub-ballast
especially in the case of weak soil sub-grades.
Benefits of Moorum Ballast
• Provides good aesthetics to the track.
Drawbacks of Moorum Ballast
• It is very soft and when subjected to vibrations gets converted into a powdered
form and blows away.
• Not recommended unless there is no other material available.
5. Coal Ash or Cinder Ballast: Coal ash also called cinder is the by-product of coal-fired
power plants and railway locomotives. It can be used as a ballast material since it is
cheaply available and also possesses good drainage properties. It is used as ballast
especially for station yards and as initial ballast for newly constructed tracks.

Benefits of Coal Ash Ballast


• It is economical and abundantly available. o It has excellent drainage
properties.
• It can be handled with ease and is light in weight.
Drawbacks of Coal Ash Ballast

• Makes the track dirty and complicates the maintenance procedure.


• It is not recommended when steel sleepers are used because of its corrosive
action.
• The rails may also get affected by the corrosive action of coal ash.
6. Brickbat Ballast: Brickbats are nothing but crushed pieces of bricks which are generally
over-burnt. Under-burnt brickbats are not suitable since they are not as porous as over-burnt
brickbats.
Benefits of Brickbat Ballast
• Porous brickbats have good drainage
properties.
• Brickbats are useless products of brick industries and hence can be bought at
cheap prices.

Drawbacks of Brickbat Ballast


• When subjected to loads they turn into a powder which can be easily blown
away by the wind.
• The brick dust makes the track dirty and demands frequent maintenance.
TRACK FITTINGS AND FASTENINGS
Track fittings and fastenings are fittings requires for joining of rails end to end and also for
fixing the rails to sleepers in a track.

Functions of track fittings and fastenings

Rail fixtures and fastenings have the following functions:

(i) To join the rails, end to end to form full length of track.
(ii) To fix the rails to sleepers.
(iii) To maintain the correct alignment of the track.
(iv) To provide proper expansion gap between rails.
(v) To maintain the required tilt of rails.
(vi) To set the points and crossings in proper position.
TRACK STRESS
❖ The wheel loads: The static load due to wheel is transmitted to the point of contact of
the wheel and the rail.
❖ Dynamic effect of wheel loads: The dynamic effect is caused due to speed and hammer
blows by the moving wheels.
❖ Hammer blow: Due to over balance of driving wheels of locomotive.
❖ The horizontal thrust: Due to nosing action of the locomotive.
❖ The pressure by the flanges of wheels on the sides of the rail: There is lateral
pressure due to flanges collision with the rails because the locomotive or train moves
in zig-zag manner.
❖ Stresses due to irregularities in the track: When ballast or subgrade are not evenly
laid, non-uniformity in the gauge and top of the rails are not in one level.
❖ Additional stresses on curves: Lateral bending due to rigid wheel base of the vehicle
and non-uniform distribution of pressure over outer and inner wheels.

CONING OF WHEELS
• The distance between the inside edges of wheel flanges is generally kept less than the
gauge of the track.

• So, there is a gap between the wheel flanges and running edges of the rails, nearly equal
to 1cm on either side.
• These wheels are coned at a slope of 1 in 20.

The advantages of coning of the wheels are

▪ To reduce the wear and tear of the wheel flanges and rails.
▪ To provide a possibility of lateral movement of the axle with its wheels.
▪ To prevent the wheels from slipping to some extent.
▪ It provides a smooth ride.
▪ It helps the train to negotiate a curve smoothly.

TILTING OF RAILS
• Rails are tilted inward at an angle of 1 in 20 to reduce wear and tear on the rails as well
as on the tread of the wheels.
• As the pressure of the wheel acts near the inner edge of the rail, there is heavy wear and
tear of the rail.
• Lateral bending stresses are also created due to eccentric loading of rails.
• To reduce the wear and tear as well as lateral stresses, rails are tilt ed at a slope of 1 in
20, which is also the slope of wheel cone.

CREEP OF RAILS
▪ It is defined as the longitudinal movement of rails with respect to sleepers in a track.
▪ Creep is common to all railway tracks, but varies in magnitude considerably, the rail in
some places moves by several centimetres in a month while in other location the
movement of rails may be negligible.
▪ It is observed that the rails have tendency to move gradually in the direction of dominant
traffic.
Indications of creep can be noticed from the following observations:

▪ Closing of successive expansion spaces at rail joints in the direction of creep and
opening out of joints at the point from where creep starts.
▪ Marks on flanges and webs of rails made by spike heads, by scraping or scratching as
the rail slide.
Causes of creep
▪ Ironing effect of the wheel: The ironing effect of moving wheels on the waves
formed in the rail tends to cause the rail to move in the direction of traffic, results
in creep.
▪ Changes in temperature: Temperature variations cause unequal expansion and
contraction of rails; creep is more in hot weather.
▪ Brakes: Creep is also caused due to forces that come into operation when the train
is stopping or starting by applying breaks. When it starts, the wheel pushes the rails
backward and when it stops, the wheels, push the rails forward.
▪ Track alignment: creep is more on curves than on straight tracks.
▪ Track gradient: Creep is more on steeper gradients than on flat gradients.
▪ Poor maintenance: when the cracks are not maintained properly, more creep
develops. Fish plates become loose.
▪ Old rail sections: creep is more in case of old rail section than new rail sections.
▪ Unbalanced traffic: In case of single track, the traffic runs in both directions and
therefore, the effect of creep is negligible. Where as in double track, the traffic runs
in the directions and therefore, the effect of creep be more.
▪ Type of ground surface on which track is laid: Creep is more in case of tracks
laid over swampy or boggy land.
DEFECTS IN RAILS
Rail wear and the battering of rail ends are the two major defects in rails.
Other defects are,

➢ Hogging of rails

• Rail ends get hogged due to poor maintenance of the rail joint, yielding
formation, loose and faulty fastenings, and other such reasons.
• Hogging of rails causes the quality of the track to deteriorate.
• This defect can be remedied by measured shovel packing.

➢ Scabbing of rails

• The scabbing of rails occurs due to the falling of patches or chunks of metal
from the rail table.
• Scabbing is generally seen in the shape of an elliptical depression, whose
surface reveals a progressive fracture with numerous cracks around it.
➢ Wheels burns
• Wheel burns are caused by the slipping of the driving wheel of locomotives on
the rail surface.
• As a consequence, extra heat is generated and the surface of the rail gets
affected, resulting in a depression on the rail table.
• Wheel burns are generally noticed on steep gradients or where there are heavy
incidences of braking or near water columns.

➢ Shelling and black spots


• Shelling is the progressive horizontal separation of metal that occurs on the
gauge side, generally at the upper gauge corner.
• It is primarily caused by heavy bearing pressure on a small area of contact,
which produces heavy internal shear stresses.

➢ Corrugation of rails
• Corrugation consists of minute depressions on the surface of rails, varying in
shape and size and occurring at irregular intervals.
• The factors which help in the formation of rail corrugation, however, are briefly
enumerated here.

(a) Metallurgy and age of rails

(b) Physical and environment conditions of track

(c) Train operations

(d) Atmospheric effects


ROUTE ALIGNMENT SURVEYS

1. Conventional Method

In the manual method how, we can get generate railway alignment by the following various
surveys which consume a huge time and money and sources too. In order to have a proper and
satisfactory new route, various surveys are carried out:

1. Reconnaissance Survey
2. Preliminary Survey
3. Location Survey
Reconnaissance Survey: It is the first engineering survey. It is a rough and visual
identification about location and check map data to live location. A reconnaissance survey can
divide into two parts:
➢ Traffic survey
➢ Engineering survey
Traffic survey: This consists of collection of the information regarding the following:

• The general scenario of the location.


• Information of the local industries.
• The general information of agriculture, crop types and any mineral sources are there or
not.
• The probable scenario of traffic to divert or used by new railway alignment.
• General study of existing transportation facilities and which mode is mostly used.
Planning forecasting of economic and social growth of area that would be covered by
this new railway line.
• Physical features of the country
Engineering survey:
• The surface of the ground;
• Types of soil and its classification
• Streams and rivers, those which will cross the proposed railway line;
Preliminary Survey:

Object of preliminary survey


• To conduct the survey work along the alternative routes found out by reconnaissance
• To determine with greater accuracy the cost of the railway line along these alte rnative
survey and; routes.

Importance of preliminary survey


• It decides the final route and recommends only one particular route in preference to
other alternative routes
• Thus, should be carried out with great precision as on it depends the alignment of the
final route.

Location Survey:

Object of location survey


• To carry out the detailed survey of the selected route to find whether it is economical
and feasible? From preliminary surveys data. It the centre-line of the alignment track
to be laid.

• As soon as the location survey is completed, the construction work is started.

Work of location survey is carried out in two stages,

1. Paper location:

• The final route selected is put up on paper and details such as gradient, curves, contours, etc.
are worked out;

• All the working drawings are prepared, even of minor structures such as signal cabins.
• After the paper location is over, the field work is started and the centre-line of the track is
fixed.
2. Field location:
• The field location transfers paper location on the ground.
• It gives all the requirements of the construction engineer such as bench-marks, levels,
measurements, etc.
• The centre-line pegs are driven at every 300 meters along the centre-line of the track. Every
change of direction, the beginning and end of the curve and also the intersecting points are
clearly marked.

• In addition to the fixing up of the centre-line of the track, the centre -lines of bridges, culverts,
tunnels, station buildings, signal cabins, etc. should also be fixed.
2. MODERN METHODS
▪ GIS study: This how we can generate various thematic maps for any particular area.
▪ Planning of proposed railway alignment with the help by generating thematic
maps safety: The track should be aligned so as to ensure that goods and passengers are
transported with minimal chances of accidents and derailment.
▪ Aesthetic aspect: The railway line should be constructed to provide a memorable and
pleasant railway journey to train passengers by keeping the track within beautiful
natural surroundings.
▪ Economy: The track should be as short and direct as possible with minimal
construction, maintenance and operating costs from an engineering perspective.
▪ Linking of centers: A new railway line should connect and inter link important town
centers and cities so as to provide the necessary transportation services.
SOIL SUITABILITY ANALYSIS
❖ Many different types of soils may be suitable for use in the construction of an embankment or
fill, ranging from granular soils (sand and gravel), which are highly desirable, to the more finely
sized soils (silt and clay), which are usually somewhat less desirable.
❖ Certain types of soils (such as saturated clays and highly organic soils) are considered
unsuitable for use as materials in embankment or fill construction.
❖ Regardless of the type(s) of soil(s) used to construct embankments or fills, the material should
be well graded, capable of being well compacted, be within a proper range of moisture to
optimize compaction, and be free of unsuitable or deleterious materials, such as tree roots,
branches, stumps, sludge, metal, or trash.
Material Properties and Testing Methods
Some of the more important properties of materials that are used for the construction of
embankments or fills include:
❖ Gradation: Well-graded fill materials that consist of two or more soil types, usually a
mixture of granular and fine-grained soils, are most suitable for embankment
construction. Because of the wide variety of soils that may be encountered, there is no
universally recommended range of gradation for fill materials, although the maximum
layer. particle size should be less than 100 mm so that it can be readily placed within a
200 mm.
❖ Unit Weight and Specific Gravity: Fill materials can vary in unit weight over a fairly
wide range, depending on the type of material and its moisture content. Fill materials
that are relatively low in unit weight offer the advantage of transmitting less dead load
to the underlying soil that supports an embankment.
❖ Moisture Density Characteristics: The compaction characteristics (optimum
moisture content and maximum dry density) of a soil fill material are the most important
single property that affects embankment performance. Most specifications for
embankment construction require the compacted fill material to have an in-place
density that is within a certain percentage (usually 95 percent or greater) of the
maximum dry density at a moisture content that is within a certain percentage (usually
3 percent or less) of optimum. The optimum moisture and maximum dry density of fill
material(s) are determined in advance in the laboratory by means of either standard or
modified moisture-density compaction tests. These tests methods are applicable for
soils or earthen fill materials. Moisture-density characteristics cannot usually be
determined for oversize (over 100 mm materials) materials.
❖ Shear Strength: The shear strength characteristics (cohesion and/or inter nal friction)
are indicative of the ability of a fill material to support loads that are imposed upon it
under given drainage conditions. Shear strength characteristics are not always specified
for earthen fill materials, but are determined by tri-axial compression or direct shear
testing and are used to compute the slope stability of an embankment.
❖ Compressibility: Compressibility refers to the consolidation or settlement
characteristics of a material under long-term loading conditions. The compressibility of
a fill material is related to its shear strength, degree of compaction, void ratio,
permeability, and degree of saturation. The settlement characteristics of an earthen fill
material are determined by one-dimensional consolidation testing. Some settlement of
an embankment or fill will occur during its construction, while the remainder of the
settlement (if any) will occur in the post construction period.
❖ Bearing Capacity: bearing capacity refers to the ability of a fill material to support the
loadings imposed upon it over the life of the facility without undue settlement, volume
change, or structural damage. Bearing capacity can be determined by laboratory testing
and by field load tests.
❖ Permeability: Permeability or hydraulic conductivity refers to the ability of a soil to
transmit water through the pore structure of the fill material at a given rate. This
property is indicative of the ability of a compacted fill material to provide drainage for
excessive moisture.
❖ Corrosion Resistance: Corrosion is a basic chemical or electro-chemical property of a
material that can induce damage to concrete structures, steel piles, or metal
appurtenances with which the embankment or fill material may come in contact.
GEOMETRIC DESIGN OF TRACK
Necessity of geometric design of a railway track consideration:
❖ To ensure the smooth and safe running of trains.
❖ To achieve maximum speed.
❖ To carry heavy axle loads.
❖ To avoid accidents and derailments due to a defective permanent way.
❖ To ensure that the track requires least maintenance.
❖ For good aesthetics.
GRADIENTS
• Gradients are provided to negotiate the rise or fall in the level of the railway track.
• A rising gradient is one in which the track rises in the direction of movement of traffic
and in a down or falling gradient the track loses elevation the direction of movement of
traffic.
• Sometimes the gradient is indicated as per cent rise or fall.

For example, if there is a rise of 1 A gradient is normally represented by the distance travelled
for a rise or fall of one unit m in 400 m, the gradient is 1 in 400 or 0.25 per cent.

Gradients are provided to meet the following objectives:


(a) To reach various stations at different elevations
(b) To follow the natural contours of the ground to the extent possible
(c) To reduce the cost of earthwork
Types Of Gradients
Ruling Gradient: The ruling gradient is the steepest gradient that exists in a section. It
determines the maximum load that can be hauled by a locomotive on that section. While
deciding the ruling gradient of a section, it is not only the severity of the gradient, but also its
length as well as its position with respect to the gradients on both sides that have to be taken
into consideration. The power of the locomotive to be put into service on the track also plays
an important role in taking this decision, as the locomotive should have adequate power to haul
the entire load over the ruling gradient at the maximum permissible speed.

In plain terrain: 1 in 150 to 1 in 250


In hilly terrain: 1 in 100 to 1 in 150

Once a ruling gradient has been specified for a section, all other gradients provided in that
section should be flatter than the ruling gradient after making due compensation for curvature.

Pusher or Helper Gradient: In hilly areas, the rate of rise of the terrain becomes very important
when trying to reduce the length of the railway line and, therefore, sometimes gradients steeper
than the ruling gradient are provided to reduce the overall cost. In such situations, one
locomotive is not adequate to pull the entire load, and an extra locomotive is required. When
the gradient of the ensuing section is so steep as to necessitate the use of an extra engine for
pushing the train, it is known as a pusher or helper gradient. A Pusher gradient of 1 in 75, 1 in
100 is generally used.

Momentum Gradient: The momentum gradient is also steeper than the ruling gradient and can
be overcome by a train because of the momentum it gathers while running on the section. In
valleys, a falling gradient is sometimes followed by a rising gradient. In such a situation, a train
coming down a falling gradient acquires good speed and momentum, which gives additional
kinetic energy to the train and allows it to negotiate gradients steeper than the ruling gradient.
In sections with momentum gradients there are no obstacles provided in the form of signals,
etc., which may bring the train to a critical juncture.

Gradients in Station Yards: The gradients in station yards are quite flat due to the following
reasons:

(a) It prevents standing vehicles from rolling and moving away from the yard due to the
combined effect of gravity and strong winds.

(b) It reduces the additional resistive forces required to start a locomotive to the extent
possible.

It may be mentioned here that generally, yards are not levelled completely and certain flat
gradients are provided in order to ensure good drainage. The maximum gradient prescribed in
station yards on Indian Railways is 1 in 400, while the recommended gradient is 1 in 1000.

SUPER ELEVATION

• When a train moves round a curve, it is subjected to a centrifugal force acting


horizontally at the center of gravity of each vehicle radially away from the center of the
curve. This increases the weight on the outer rail.
• To counteract the effect of centrifugal force, the level of the outer rail is raised above
the inner rail by a certain amount to introduce the centripetal force.
• This raised elevation of outer rail above the inner rail at a horizontal curve is called
super elevation (e).

Limits of Super elevation

• Super elevation should be provided in such a way that train as to accommodate various
trains running with different speeds from time to time.

• Normally the maximum value of super elevation according to railway board is 1/10th of
gauge.

• But recently, the following values of maximum super elevation have been prescribed
on Indian railways varying from 1/10th to 1/12th of the gauge.

• Maximum S.E for B.G = 1.676 m * 1/10 = 0.1676 m = 16.76 cm

• Maximum S.E for M.G = 1.000 m * 1/10 = 0.100 m = 10.00 cm

DIFFERENT TYPES OF GAUGES

❖ Broad Gauge: When the clear horizontal distance between the inner faces of two
parallel rails forming a track is 1676 mm the gauge is called Broad Gauge (B.G). This
gauge is also known as standard gauge of India and is the broadest gauge of the world.
The other countries using the Broad Gauge are Pakistan, Bangladesh, Sri Lanka, Brazil,
Argentine, etc.

Suitability: Broad gauge is suitable under the following Conditions: -


• When sufficient funds are available for the railway project.
• This gauge is therefore, used for tracks in plain areas which are densely populated i.e.,
for routes of maximum traffic, intensities and at places which are centres of industry.

❖ Metre Gauge: - When the clear horizontal distance between the inner faces of two
parallel rails forming a track is 1000 mm, the gauge is known as Metre Gauge (M.G)
The other countries using Metre gauge are France, Switzerland, Argentine, etc.

Suitability: Metre Gauge is suitable under the following conditions:

• When the funds available for the railway project are inadequate.
• This gauge is therefore, used for tracks in under-developed areas and in interior areas,
where traffic intensity is small and prospects for future development are not very
bright.

❖ Narrow Gauge: - When the clear horizontal distance between the inner faces of two
parallel rails forming a track is either 762 mm or 610 mm, the gauge is known as
Narrow gauge (N.G) The other countries using narrow gauge are Britain, South
Africa, etc.

Suitability: Narrow gauge is suitable under the following conditions: -

• When the construction of a track with wider gauge is prohibited due to the provision
of sharp curves, steep gradients, narrow bridges and tunnels etc.
• This gauge is, therefore, used in hilly and very thinly populated areas.
• The details of the various gauges existing on Indian Railways are given in Table
below.

Name of the Gauge Width (m)


Broad Gauge 1.676
Narrow Gauge 0.762, 0.610
Metre Gauge 1.000
WIDENING OF GAUGE ON CURVES

The widening of the gauge on curves can be calculated using the formula Extra width on curves

𝟏𝟑∗(𝐁+𝐋)²
Extra width on curves =
𝑹

B is the wheel base of the vehicle in metres,

R is the radius of the curve in metres,

L = 0.02 (h +Dh) ½ is the lap of the flange in metres,

h is the depth of flange below top of the rail, and

D is the diameter of the wheel of the vehicle.

Maximum S.E for N.G = 0.760 m * 1/10 = 0.076 m = 7.60 cm


POINT AND CROSSING

• In case of roads, the facilities for turning of vehicles from one path to another, don't
require any special arrangements as the wheels have no flanges.
• The problems of diversion of trains from one track to another is solved by special
arrangements known as points & crossings.
• Points and crossings are provided facilitates the change of railway vehicles from one
track to another.
• The tracks may be parallel, diverging, or converging to each other.
Necessity

❖ Provide flexibility movement by connecting one line to another according to


requirements.
❖ They also help for imposing restrictions over turnouts which necessarily retard the
movements.
❖ Safety aspects, it is also important as points & crossings are weak kinks or points in
the track and vehicle are suitable to derailment at take place.

Terms In Points and Crossing

Turnout: It is simplest arrangement of points and crossings which enables one track either a
branch line or siding, to take off from another track.

Direction of a turnout: A turnout is designated as a right-hand or a left-hand turnout depending


on whether it diverts the traffic to the right or to the left.

Crossing: It is a device introduced at the junction where two rails cross each other to permit
the wheel flange.

Facing Direction: If someone stands at toe of switch and looks towards crossing, then the
direction is called facing direction.

Trailing Direction: if someone stands at the crossing and looks towards the switches, then the
direction is called trailing direction.

Left – Hand and Right-Hand Turnout: if a train from a main track is diverted to the left of
the main route in the facing direction, then the diversion is called left hand turnout. If a train
from a main track is diverted to the right of the main route in the facing direction, then the
diversion is called right hand turnout.

You might also like