Datasheet: uni QNB Ball

EN

Plastic Modular Belt

Series uni QNB Type Ball
Straight running belt
Nominal pitch: 25.4 mm (1.00 in)
P
Surface type: Ball
R Surface opening: Closed

STANDARD
Backflex radius: 25.0 mm (0.98 in)
T
L Pin diameter: 5.0 mm (0.20 in)
n
ctio
dire R
ning
Run

Belt material
B
POM-SLF mm in mm in
& color

Ball material P
B
PA6.6 25.4 1.00 R 1.95 0.08
& color (Nominal)

Pin material
PP B L 4.4 0.17 T 8.8 0.35

STRAIGHT RUNNING
& color

Non standard material and color: See uni Material and Color Overview.

Permissible tensile force Belt weight Number of wear

(Belt/pin material) (Belt/pin material) strips (min no)
Belt width *
Min No
drive sprocket
POM-SLF/PP POM-SLF/PP per shaft Carry
** **
Return
(pcs) (pcs)
mm in N lbf Kg/m Ib/ft

76 3.0 1710 384 0.7 0.48 2 2 2

153 6.0 3443 774 1.4 0.96 2 2 2

229 9.0 5153 1158 2.1 1.43 2 2 2

305 12.0 6863 1543 2.8 1.91 3 3 2

PITCH 25.4 MM/1.00 IN

381 15.0 8573 1927 3.5 2.38 3 3 2

457 18.0 10283 2312 4.3 2.86 4 4 2

533 21.0 11993 2696 5.0 3.33 4 4 2

609 24.0 13703 3080 5.7 3.81 5 5 3

685 27.0 15413 3465 6.4 4.28 5 5 3

761 30.0 17123 3849 7.1 4.76 6 6 3

838 33.0 18855 4239 7.8 5.24 6 6 3

914 36.0 20565 4623 8.5 5.71 7 7 4

990 39.0 22275 5007 9.2 6.19 7 7 4

1066 42.0 23985 5392 9.9 6.66 8 8 4

Additional standard belt widths are available in steps of 76.3 mm (3.00 in).

1979 77.9 44528 10010 18.4 12.37 14 14 7

Additional standard belt widths are available in steps of 76.3 mm (3.00 in).

2968 116.9 66780 15012 27.6 18.55 20 20 10

General belt tolerance is +0/-0.4% at 23°C/73°F and 50% RH. For exact belt width contact Customer Service.
*Max. Load per Drive Sprocket. Belt material: POM-SLF 1840 N (414 lbf).
**Max. Spacing between wear strips, Carry: 152.0 mm (6.00 in); Return: 304.0 mm (12.00 in).
= Single Link
 Datasheet: uni QNB Ball

Sprocket

Single row/Two way

Dimension

Dimension
Bore size

diameter

diameter

diameter

Machined PA6 N
Overall

Pitch

Hub
No. of teeth

B
1.50

1.57

2.36

2.50
in
Pilot bore

38.1

40.0

60.0

63.5
mm

mm in mm in mm in mm in mm in

Z15  121.5 4.78 122.5 4.82 100.0 3.93 55.4 2.18 66.1 2.60  
Z18  146.1 5.75 146.3 5.76 120.0 4.72 67.6 2.66 78.4 3.08  
Z19  154.2 6.07 154.3 6.07 125.0 4.92 71.7 2.82 82.5 3.24  
Non standard material
Machined sprocket and color: See uni Material
and Color Overview.

Other sprocket sizes are available upon request.

Two-part sprockets are available upon request.
Other bore sizes are available upon request.
uni Retainer Rings: See uni Retainer Ring data sheet.
Width of tooth = 8.0 mm (0.31 in)
Width of sprocket = 25.0 mm (0.98 in)

Max load per sprocket shown does not take bore size into account.
Please also ensure that sufficient size shaft is chosen for corresponding load.

For correct sprocket position: See uni Assembly Instructions for uni QNB Ball.
For more detailed sprocket information. contact Customer Service.

uni QNB Ball/2019.09.11

Expert advice, quality solutions Ammeraal Beltech Modular A/S

Transmission Belts
Conveyor Belts

Seamless Belts

and local service Hjulmagervej 21

Modular Belts

Timing Belts

Fabrication

for all your belting needs DK-7100 Vejle

& service

www.ammeraalbeltech.com
T +45 7572 3100
This information is subject to alteration due to continuous development. Ammeraal Beltech will not be held liable for the incorrect F +45 7572 3348
use of the above stated information. This information replaces previous information. All activities performed and services rendered by [email protected]
Ammeraal Beltech are subject to general terms and conditions of sale and delivery, as applied by its operating companies. www.unichains.com