Scribd
Upload
898 views3 pages

OLT Configuration

The document provides steps for configuring a Huawei OLT, including: 1. Connecting to the OLT via its default IP address and logging in. 2. Configuring the system name and checking for boards that need installation. 3. Adding interface, IP address, gateway and VLAN configurations for management access. 4. Activating ONT auto-find on GPON ports, creating DBA profiles for bandwidth allocation, and line profiles for data and voice services. The final steps add an ONT with serial number, line and service profiles, and configure service ports.

Uploaded by

Eric Kerr
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
898 views3 pages

OLT Configuration

The document provides steps for configuring a Huawei OLT, including: 1. Connecting to the OLT via its default IP address and logging in. 2. Configuring the system name and checking for boards that need installation. 3. Adding interface, IP address, gateway and VLAN configurations for management access. 4. Activating ONT auto-find on GPON ports, creating DBA profiles for bandwidth allocation, and line profiles for data and voice services. The final steps add an ONT with serial number, line and service profiles, and configure service ports.

Uploaded by

Eric Kerr
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

Plan of blank HUAWEI OLTY configuration

1- first step we connect with HUAWEI OLT through default IP address 10.11.104.2/24 with PC
through interface which had been existed at control board at slot 9 or 10

2- After getting HUAWE OLT reachability we can login to it through telnet command
Telnet 10.11.104.2 after that the user name =root and password will admin or admin123 as a
default.

3- OLT>enable
OLT#config
OLT(config)#systemname Diwaniya ( as example )

4- If there are boards process installation with HUAWEI OLT so we can check whether there are
some of boards need to be installed by using a command display board 0 so this command will
show if there are some boards need to be added and we can use a command confirm board X/X
5-
6- Then we can add interface vlan managements reaching HUAWEI OLT from another gatway as
shown below :-

OLT(config)# vlan 100 smart

OLT(config)#vlan name 100 management

OLT(config) port vlan 100 0/19 0 ( So 0 mean a port number with uplink interface board at slot
19 .

After that we will configure ip address and gateway with IP interface vlan as shown below:-

OLT(config)#interface vlan 100

OLT(config-if-vlan)# ip add 192.168.110.2 255.255.255.0

Then we will add default gateway with a command as shown below:-

OLT(config)#ip route-static 0.0.0.0 0.0.0.0 192.168.110.1

7- With this step need to configure service vlan as show below


8- OLT(config)# vlan 100 smart
OLT(config)#vlan name 100 HSI
OLT(config) port vlan 100 0/19 0

9- After that we activate ONT-auto-find for all GPON ports at slot 0 for ex as show below :-
OLT(config-if-gpon-0/1)#port 0 ont-auto-find enable // so this command will be repeated by
number of ports which installed at GPON boards
10- At this step we will create DBA (Dynamic bandwidth allocation) for ONT that specify a maximum
bandwidth that can be reached for ONT with command as shown below :-

OLT(config)# dba-profile add profile-id 10 profile-name HSI type4 max 1024000 This command for
internet service

OLT(config)# dba-profile add profile-id 11 profile-name VOICE type1 fix 1024 // This command for
Voice service but it need for adding voice-vlan and gateway with voice gate way .

Note :-Command above will be used for adding DBA profile that declare BW which is used by ONT
which equal to 1 G

11- At this step we will create ONT line profile for data and voice services with this command as
shown below :-

OLT(config)# ont-lineprofile gpon profile-id 10 profile-name HSI&Voice services

OLT(config-gpon-lineprofile-10)# tcont 1 dba-profile-id 10 // dba profile which is created at step 10

OLT(config-gpon-lineprofile-10)# tcont 2 dba-profile-id 11 // dba profile which is created at step 10

gem add 1 eth tcont 1 // This command will be repeated by depending on number of services to add
gem and TCON number respectively .

gem add 2 eth tcont 2 // This command will be repeated by depending on number of services to
add gem and TCON number respectively .

gem mapping 1 1 vlan 10 // This command will be used for forwarding a traffic through gem,tcon to
user vlan tag which vlan- id configured at ONT and here for internet service

gem mapping 2 2 vlan 30 // This command will be used for forwarding a traffic through gem,tcon to
user vlan tag which id configured at ONT and here for voice service.

OLT(config-gpon-lineprofile-10)#comit // This command will be used for saving a configuration at


line profile .

12- We will create GPON service profile with command as shown below :-
OLT(config)#ont-srvprofile gpon profile-id 11 profile-name "Call&HSI"
OLT(config-gpon-srvprofile-11)# ont-port pots 2 eth 4
OLT(config-gpon-srvprofile-11)# port vlan eth 1 translation 10 user-vlan 10
OLT(config-gpon-srvprofile-11)# port vlan eth 2 translation 10 user-vlan 10
OLT(config-gpon-srvprofile-11)# port vlan eth 3 translation 10 user-vlan 10
OLT(config-gpon-srvprofile-11)# port vlan eth 4 translation 10 user-vlan 10
OLT(config-gpon-srvprofile-11)# port vlan iphost translation 30 user-vlan 30
OLT(config-gpon-srvprofile-11)# commit
Now most of HUAWEI OLT configuration steps are completed then we will add ONT at OLT as show
below as one steps of a service provisioning:-

ont add 2( GPON port number) ONT number sn-auth "ONT serial number" omci ont-lineprofile-
id 10 ont-srvprofile-id 11 desc "Name of user + ONT location FDT,FAT, FAT Number"

ont port native-vlan 2 6 eth 1 vlan 10 priority 0

ont port native-vlan 2 6 eth 2 vlan 10 priority 0

ont port native-vlan 2 6 eth 3 vlan 10 priority 0

ont port native-vlan 2 6 eth 4 vlan 10 priority 0

ont port native-vlan 2 6 iphost vlan 30 priority 5

quit

service-port 1158 vlan 601 gpon 0/6/2 ont 6 gemport 1 multi-service user-vlan 10 tag-transform
translate inbound traffic-table index 6 outbound traffic-table index 6

service-port 6658 vlan 2222 gpon 0/6/2 ont 6 gemport 2 multi-service user-vlan 30 tag-transform
translate inbound traffic-table index 4 outbound traffic-table index 4

ENG:-Ahmed Hameed

You might also like