International Journal of Advanced Mechanical Engineering.

ISSN 2250-3234 Volume 4, Number 4 (2014), pp. 425-434

© Research India Publications
http://www.ripublication.com/ijame.htm

Optimization of Electrical Discharge Machining Process

Parameters Using Taguchi Method

Chandramouli S1, Shrinivas Balraj U2 and Eswaraiah K3

1
Department of Mechanical Engineering, Kakatiya Institute of Technology & Science,
Yerragattu Hillock, Hasanparthy, Warangal (AP), India.
2,3
Department of Mechanical Engineering, Kakatiya Institute of Technology &
Science, Yerragattu Hillock, Hasanparthy, Warangal(AP), India.

Abstract

The objective of this research study is to investigate the optimal

process parameters of Electric Discharge Machining on RENE80
nickel super alloy material with aluminum as a tool electrode. The
effect of various process parameters on machining performance is
investigated in this study. The input parameters considered are current,
pulse on time and pulse off time are used for experimental work and
their effect on Material Removal Rate, Tool Wear Rate and Surface
Roughness. The Taguchi method is used to formulate the experimental
layout, ANOVA method is used to analysis the effect of input process
parameters on the machining characteristics and find the optimal
process parameters of Electric Discharge Machining. The results of the
present work reveal that proper selection of input parameters will play
a significant role in Electric Discharge Machining.

Keywords: Electrical Discharge Machining, orthogonal array, metal

removal rate, tool wear rate ANOVA.

1. Introduction
Electric Discharge machining (EDM) is a thermo-electric, non-traditional machining
process used to machine precise and intricate shapes on difficult to cut materials and
super tough metals such as ceramics, maraging steels, cast-alloys, titanium which are
widely used in defence and aerospace industries. Electrical energy is used to generate
electrical sparks and material removal mainly occurs due to localized melting and
vaporization of material which is carried away by the dielectric fluid flow between the
426 Chandramouli S et al

electrodes. The performance of this process is mainly influenced by many electrical

parameters like, current, voltage, polarity, and pulse on time, pulse of time, electrode
gap and also on non-electrical parameters like work and tool material, dielectric fluid
pressure. All these electrical and non electrical parameters have a significant effect on
the EDM output parameters like, Metal Removal Rate (MRR), Tool Wear Rate (TWR)
and Surface Roughness(SR). The EDM is very complex and stochastic process and is
very difficult to determine the optimal machining parameters. In the present study the
output responses MRR ,TWR and SR are conflicting in nature. MRR reflects the
productivity and tool wear reflects the accuracy of the product. So in this work it was
proposed to study the effects of different input parameter current ,pulse on time and
pulse off time on Material removal rate, Tool wear rate and Surface roughness with
EDM oil as a dielectric. The experimental design has been done by using Taguchi
technique. The response has been analysed using S/N ratio and analysis of Variance.

2. Experimental Details
The experiments were conducted on V3525 precision die sink electric discharge
machine as shown in Fig.1 which consist a work table, a servo control system and a
dielectric supply system. The machine has 8 current settings from 3A to 24A, 9
settings of pulse on time, 9 settings of pulse off time and spark gap of 50-75 microns
The experiments are conducted on RENE80 Nickel Super alloy(Russian grade -RZ)
and the work piece dimensions are 70 mm x 35 mm x 5 mm. Work piece material
properties are: Hardness (HRC)= 43-45, density (g/cm3)=8.16, Ultimate tensile
strength (Kg/mm2) =85, Elongation % =3, Creep strength (0C) = 975. Thermal
conductivity (W/m0K)= 11.50. The tool material used is aluminium- density 2.70
gm/cm3 and thermal conductivity 237 w/m0k and the machining is done with straight
polarity. EDM oil Grade 30 is used as the dielectric fluid and the experiments were
performed for a particular set of input parameters. The number of experiments and,
input levels are decided based on the design of experiments and the input parameters
and their levels are presented in Table 1. The MRR and TWR are calculated using
digital balance of accuracy 1mg and the machining time is using digital watch of
accuracy 1 microsecond and the surface roughness is measured using Taylor Hobson
Talysurf machine for a sampling length of 5mm.

Fig. 1: The Experimental equipment.

Optimization of Electrical Discharge Machining Process Parameters Using 427

The MRR and TWR are calculated using the following expressions.
MRR= 1000×( Wb- Wa) /t mg/min
TWR= 1000×( Tb–Ta ) /t mg/min
Wb : Weight of the work-piece before machining
Wa : Weight of the work-piece after machining
Tb : Weight of the tool before machining
Ta : Weight of the tool after machining
t: Machining time (minutes)

Table 1: Input Parameters Levels.

Input Current Pulse on Pulse off Time
Parameters (amp) Time (µs) (µs)
Symbol A B C
Level1 6 10 10
Level2 15 20 20
Level3 24 30 50

3. Over View of Taguchi Method

Taguchi method involves reducing the variation in a process through robust design of
experiments. The overall objective of the method is to produce high quality product at
low cost to the manufacturer. Taguchi developed a method for designing experiments
to investigate how different parameters affect the mean and variance of a process
performance characteristic that defines how well the process is functioning. The
experimental design proposed by Taguchi involves using orthogonal arrays to organize
the parameters affecting the process and the levels at which they should be varied; it
allows for the collection of the necessary data to determine which factors most affect
product quality with a minimum amount of experimentation, thus saving time and
resources. Taguchi design method is to identify the parameter settings which render the
quality of the product or process robust to unavoidable variations in external noise. The
relative “quality” of a particular parameter design is evaluated using a generic signal-
to-noise (S/N) ratio. Depending on the particular design problem, different S/N ratios
are applicable, including “lower is better” (LB), “nominal is best” (NB), or “higher is
better” (HB).
As the objective is to obtain the high material removal rate , low tool wear rate, and
best surface finish, it is concerned with obtaining larger value for MRR, smaller value
of tool wear rate and smaller value of surface roughness .Hence, the required quality
characteristic for high MRR is larger the better, which states that the output must be as
large as possible, and for tool wear rate and surface roughness is smaller the better,
which states that the output must be as low as possible.
428 Chandramouli S et al

4. Design Of Experiments and Data Analysis

Based on L9 orthogonal array experiments are conducted on RENE80 nickel super
alloy with aluminium tool and EDM grade 30 oil as dielectric medium for different
experiment levels which are show in Table.2. To achieve validity and accuracy each
test is repeated three times. Particular attention was paid to ensure that the operating
conditions permitted the effective flushing of machining debris from the working
region. The experiments were performed with the bottom surface of the electrode flat
and parallel to the work surface.

Table 2: L9 Orthogonal Array.

Expt. No A B C
1 1 1 1
2 1 2 2
3 1 3 3
4 2 1 2
5 2 2 3
6 2 3 1
7 3 1 3
8 3 2 1
9 3 3 2

5. Analysis of Varience (Anova)

The knowledge of the contribution of individual factors is critically important for the
control the final response. The analysis of variance (ANOVA) is a common statistical
technique to determine the percent contribution of each factor for results of the
experiment. It calculates parameters known as sum of squares SS, degree of freedom
(DOF), variance and percentage of each factor. Since the procedure of ANOVA is a
very complicated and employs a considerable of statistical formula. The Sum of
Squares SS(tr) is a measure of the deviation of the experimental data from the mean
value of the data[8]. The Fisher’s ratio is also called F value. The principle of the F test
is that the larger value for a particular parameter, the greater the effect on the
performance characteristics due to the change in that parameter. F value is defined as
the ratio of Mean square for the term to Mean square for the error term. all these
statistical calculations are done in MINI TAB 6.0 software.

Table 5.1: Experimental results of different trials.

Expt. No. MRR TWR SR

T1 T2 T3 AVG T1 T2 T3 AVG AVG
1 21 17 18.5 18.8 6 4.5 4 4.83 3.67
2 10 7 8.5 8.5 4.8 5.6 5.3 5.2 5.25
3 6.5 5.5 16.5 9.5 2.6 3.4 4.3 3.4 3.94
Optimization of Electrical Discharge Machining Process Parameters Using 429

4 121 127 137 128.3 24.5 25.3 29 26.3 4.18

5 76.5 73 113 87.5 13.33 11.5 19.3 14.71 5.15
6 56.5 52 50 52.8 9 9.1 11 9.7 6.46
7 250 255 256 253.6 49.33 50.67 45 48.3 5.99
8 180 150 165 165 37.16 38 31.5 35.5 5.94
9 222 210 205 212.3 34.6 35 32 33.8 6.21

Table.5.2: S/N ratios of different experiments for MRR,TWR and SR.

Expt. No. S/N ratio of MRR S/N ratio of TWR S/N ratio of SR
1 25.1199 -13.9271 -11.2933
2 19.4626 -14.6960 -14.4032
3 15.1175 -7.81870 -11.9099
4 41.9729 -28.4649 -12.4235
5 37.9195 -22.6899 -14.2361
6 34.2530 -20.0260 -16.2047
7 48.0610 -33.7844 -15.5485
8 44.2916 -29.7173 -15.4757
9 46.3654 -30.7564 -15.8618

Table.5.3: ANOVA results for MRR.

Source DOF Seq. SS Adj. MS F
Current 2 59569.3 29784.7 1004.49
Pulse on time 2 4249.1 2124.5 71.65
Pulse off time 2 2532.9 1266.5 42.71
Residual Error 2 59.3 29.7
Total 8 66410.6
DF- Degree of freedom, SS- Sum of squares, MS- Mean squares(variance),
F- Ratio of variance of a source to variance of error

Table.5.4: ANOVA Results for TWR.

Source DOF Seq. SS Adj. MS F
Current 2 1744.02 872.01 82.06
Pulse on time 2 229.18 114.59 10.78
Pulse off time 2 90.09 45.04 4.24
Residual Error 2 21.25 10.63
Total 8 2084.53

Table 5.5: ANOVA results for SR.

Source DOF Seq. SS Adj. MS F
Current 2 4.6651 2.33254 1.97
Pulse on time 2 1.5551 0.77754 0.66
Pulse off time 2 0.1643 0.08214 0.07
430 Chandramouli S et al

Residual Error 2 2.3688 1.18441

Total 8 8.7533

Table.5.6: Response Table for Means of MRR.

Level Current Pulse on Time Pulse off Time
1 11.04 132.16 77.84
2 85.27 84.00 114.33
3 208.32 88.47 112.45
Delta 197.28 48.47 36.49
Rank 1 2 3

Table 5.7: Response Table for Means of TWR.

Level Current Pulse on time Pulse off time
1 4.287 26.787 15.203
2 16.720 16.557 22.143
3 38.000 15.663 21.660
Delta 33.713 11.123 6.940
Rank 1 2 3

Table 5.8: Response Table for Means of SR.

Level Current Pulse on Time Pulse off Time
1 4.287 4.613 5.357
2 5.263 5.447 5.213
3 6.047 5.537 5.027
Delta 1.760 0.923 0.330
Rank 1 2 3

Main Effects Plot for Means

Data Means
current pulse on time
200

150

100
Mean of Means

50

0
6 15 24 10 20 50
pulse off time
200

150

100

50

0
10 20 50

Fig. 5.1: Main effect plot of mean value for MRR.

Optimization of Electrical Discharge Machining Process Parameters Using 431

Main Effects Plot for SN ratios

Data Means

current pulse on time

50

40

30
Mean of SN ratios

20
6 15 24 10 20 50
pulse off time
50

40

30

20
10 20 50
Signal-to-noise: Larger is better

Fig. 5.2: Main effect plot of S/N ratio for MRR.

Main Effects Plot for Means

Data Means

current pulse on time

40

30

20

10
Mean of Means

0
6 15 24 10 20 50
pulse off time
40

30

20

10

0
10 20 50

Fig. 5.3: Main effect plot of mean value for TWR.

Main Effects Plot for SN ratios

Data Means

current pulse on time

-10

-15

-20
Mean of SN ratios

-25

-30

6 15 24 10 20 50
pulse off time
-10

-15

-20

-25

-30

10 20 50

Signal-to-noise: Smaller is better

Fig. 5.4: Main effects plot of S/N ratio for TWR

432 Chandramouli S et al

Main Effects Plot for Means

Data Means
current pulse on time
6.0

5.5

5.0
Mean of Means

4.5

6 15 24 10 20 50
pulse off time
6.0

5.5

5.0

4.5

10 20 50

Fig. 5.5: Main effects plot of mean value for SR

Main Effects Plot for SN ratios

Data Means
current pulse on time

-13

-14
Mean of SN ratios

-15

-16
6 15 24 10 20 50
pulse off time

-13

-14

-15

-16
10 20 50
Signal-to-noise: Smaller is better

Fig. 5.6: Main effects plot of S/N ratio for SR.

6. Experimental Results and Analysis

After the collection of experimental data the calculated S/N ratio value for MRR,TWR
and SR is shown in the table no.4 The ANOVA results for MRR ,TWR and SR is
shown in table no.5.3, 5.4and 5.5 respectively and Response Table for Means of
MRR,TWR and SR is shown in table no.5.6, 5.7and 5.8 respectively. Current , pulse
on time and pulse of time is assigned as rank 1, 2, and 3 respectively according to their
larger value of delta. Rank 1 means highest contribution factor for the MRR,TWR and
SR and 3 means lowest contribution factor for MRR,TWR and SR. Pulse off time is
the least contribution parameter. From the figure no. 5.1, it is observes that MRR goes
on increasing with higher values of current. MRR has highest value at current 24A.
From the figure no. 5.3, TWR has lowest value at current 6A, pulse-on time 50μs and
pulse off time value at 10μs. For current 6A, pulse-on time 6μs and pulse off time
value at 50μs the surface finish is better than other values which shown in the figure
no. 5.5.
Optimization of Electrical Discharge Machining Process Parameters Using 433

6.1 Optimum design for MRR, TWR and SR

In the experimental analysis, main effect plot of S/N ratio for MRR,TWR and SR is
used for estimating the S/N ratio of MRR with optimal design condition. As shown in
the figure no.5.2, MRR has highest value at level 3 for current, level 1 for pulse on
time and level 3 for pulse off time.
As shown in the figure no.5.4, TWR has lowest value at level 1 for current, level 3
for pulse on time and level 1 for pulse off time.
SR has lowest value at level 1 for current, level 1 for pulse on time and level 3 for
pulse off time which shown in the figure no.5.6.

7. Conclusion
The result shows that current, pulse on time and pulse off time have significant effect
on MRR,TWR and SR. The results of the present work reveal that proper selection of
input parameters will play a significant role in Electric Discharge Machining.
• The MRR is increasing with increase in current.
• MRR is decreasing initially with increase in the pulse on time and increasing
later with an increase in pulse on time.
• MRR is increasing with increase in the pulse off time but the increase is less as
compared to pulse on time.
• TWR is increasing linearly with increase in the current.
• The TWR is decreasing with increase in pulse on time, when increase in pulse
off time the TWR is increasing.
• The SR is increasing with increase in current and pulse on time but decreasing
with increase in pulse off time.
• For optimum MRR, A3B1C3 levels must be selected and for optimum TWR,
A1B3C1 levels and for optimum SR, A1 B1 C3 must be selected.

References
[1] Gostimirovic M and Kovac P(2012), Effect of electric pulse parameters on
the machining performance in EDM , Indian journal of engineering &
Materials science 18, pp 411-415..
[2] Shankar S, Maheshwari, and S. Pandey(2004), Some investigation in to the
electric discharge machining of hardened tool steel using different electrode
material, Journal of Materials Processing Technology, 149(1-3), pp 272-277.
[3] Pichai Janmane , Kamonpong Jamkamon (2012), Investigation of Electric
Discharge Machining of Tungsten Carbide using EDM-C3 Electrode material,
European Journal of Scientific research 76(1), pp 133-142.
[4] Rahman, M.M (20120), Modelling of machining parameters of Ti-6Al-04V
for electric discharge machining: A neural network approach, scientific
research and Essays 7(8), pp 881-89.
434 Chandramouli S et al

[5] Reza Atef., Navid Javan., Farhad Teimoori.(2012) The Investigation of

EDM Parameters on electrode Wear Ratio, Research journal of Applied
Science, Engineering and Technology, 4(10), pp 1295-1299,
[6] Reza Atef., Navid Javan., Farhad Teimoori(2012), The Influence of EDM
Parameters in Finishing Stage on Surface Quality MRR and EWR, Research
journal of Applied Science, Engineering and Technology, 4(10), pp 1287-
1294.
[7] Assarzadeh S., Ghoreishi, M(2012) Neural network-based modelling and
optimization of electro-discharge machining process, International Journal of
Advanced Manufacturing Technology, 39, 488-500.
[8] Debabrata Manda., Surjay K. Pal(2007) Modelling of electric discharge
machining process using multi-objective optimization using non-dominating
sorting genetic algorithm-, International Journal of Material Processing
Technology, 186, pp 154-162.
[9] Patel, K.P. (2012), Experimental analysis on surface roughness of CNC END
Milling process using Taguchidesign Method, International journal of
Engineering science and Technology, Vol. 4, No. 2, pp 120- 128