TECHNICAL DATA

SUB2 PROFESSIONAL

POWERED BASS MODULE

(Grille removed)

Product Overview
A powered, portable bass module, the Sub2 subwoofer combines with virtually any portable PA and delivers
low-end performance down to 37 Hz. Its unique 10" × 18" high-excursion neodymium RaceTrack driver allows
for an ultra-slim enclosure, delivering performance that rivals a traditional 15" woofer without the cumbersome
size, freeing up room in your vehicle and on the stage. Compared to the Sub1 subwoofer, Sub2 is the more
powerful subwoofer option for the Bose L1 Pro32 system, combining seamlessly via single-cable SubMatch
connectivity. You can stack multiple Sub2 subwoofers for even more low end — or to unleash Cardioid Mode
for directional bass. With a Sub2, you get a subwoofer that easily fits onstage — and effortlessly fills up the
dance floor.

Key Features
Add powerful bass to your portable PA system with low-end range down to 37 Hz

Go from vehicle to venue easily with a slim design featuring a unique 10" × 18" high-excursion neodymium
RaceTrack driver; performance that rivals a conventional 15" woofer with a smaller footprint

Stack multiple Sub2 subwoofers for even more bass or unleash Cardioid Mode for focused, directional
performance that steers the bass out front and decreases feedback

Combine seamlessly with Bose L1 Pro32 portable line array via proprietary SubMatch connectivity, which
delivers both power and audio over a single cable

Pair with other powered loudspeakers via line input and output with selectable crossover modes, plus
integrated threaded pole mount for use with Bose S1 Pro PA and more

PRO.BOSE.COM/L1 1 OF 6
Technical Specifications

System Performance
Model Name Sub2
System Type Self-powered bass module
Frequency Response (–3 dB) 1
37 Hz to 180 Hz
Frequency Range (–10 dB) 29 Hz to 260 Hz
Nominal Vertical Coverage Pattern 0°
Nominal Horizontal Coverage Pattern Omnidirectional (with –10 dB rear rejection in Cardioid mode)
Calculated Maximum SPL @ 1 m, continuous 2 123.8 dB
Calculated Maximum SPL @ 1 m, peak 2
129.8 dB
Crossover 200 Hz
Transducers
Low Frequency 1 × RaceTrack low-frequency driver 10" × 18"
Low Frequency Voice Coil Size 3"
Driver Protection Dynamic limiting
Amplification
Type Class D
Low Frequency Amplifier Channel 1000 W
Cooling Convection cooling
Onboard Mixer
Channels Two
Channel 1 & 2 Input: Audio Type Combination XLR or 1/4" TRS connector (mic/instrument/line)
Channel 1 & 2 Input: Impedance 100 KΩ
Channel 1 & 2 Input: Channel Gain +10 dB to +45 dB; from input to driver, controlled by volume control
Channel 1 & 2 Input: Max Input Signal +24 dBu
Channel 1 & 2 Output: Audio Type XLR connector, line-level, full-frequency bandwidth
SubMatch Input: Audio Type Bose proprietary multi-pin cable
SubMatch Thruput: Audio Type Bose proprietary multi-pin cable
LED Indicators Standby, Phase/Pattern selection, Input EQ selection, Output EQ selection, Sig-
nal/Clip Indicator
AC Power
AC Power Input 100–240 VAC (±20%, 50/60 Hz)
Input: Electrical Type IEC, SubMatch
Initial turn on inrush current 15.2 A at 120 V; 28.6 A at 230 V
Inrush current after AC mains interruption of 5 s 2.6 A at 120 V; 6.1 A at 230 V

PRO.BOSE.COM/L1 2 OF 6
Technical Specifications

Enclosure
Color Black
Enclosures Material High-impact polypropylene, birch plywood
Grille Material Powder-coated perforated steel
Product Dimensions (H × W × D) 694 × 317 × 551 mm (27.3 × 12.5 × 21.7 in)
Shipping Dimensions (H × W × D) 660 × 385 × 790 mm (25.98 × 15.16 × 31.10 in)
Net Weight 3
23.0 kg (50.7 lbs)
Shipping Weight 27.7 kg (61.0 lbs)
Warranty Period 2 years
Included Accessories IEC power cord, slip cover
Optional Accessories Sub2 Roller Bag, Adjustable Speaker Pole, SubMatch Cable
Product Part Numbers
840917-1100 SUB2 POWERED BASS MODULE,120V,US
840917-2100 SUB2 POWERED BASS MODULE,230V,EU
840917-3100 SUB2 POWERED BASS MODULE,100V,JP
840917-4100 SUB2 POWERED BASS MODULE,230V,UK
840917-5100 SUB2 POWERED BASS MODULE,230V,AU
840917-5130 SUB2 POWERED BASS MODULE,230V,INDIA
856986-0110 PREMIUM ROLLER BAG,SUB2,BLACK
857172-0110 SUBMATCH CABLE,BLACK
857000-0110 SPEAKER STAND,SUB POLE,BLACK

Footnotes
(1) Frequency response and range measured on-axis in anechoic environment with recommended bandpass and EQ.
(2) Maximum SPL calculated using sensitivity and power ratings, exclusive of power compression.
(3) Net weight excludes slip cover and power cord.

PRO.BOSE.COM/L1 3 OF 6
Connections and Controls

f q Standby Button: Press the button to

power on the Sub. The LED will illuminate
white while the Sub is on.
w Line Inputs: Analog input for connecting
an L1 Pro or other line-level audio source.
Compatible with XLR, TRS balanced, and
PHASE/PATTERN LEVEL TS unbalanced cables.
e Line Outputs: Use an XLR cable to
q CARDIOID
d connect the line-level output to a
loudspeaker.
s
r SubMatch Thruput: Connect an additional
LINE IN 1 LINE IN 2 LINE IN EQ
Sub bass module with a SubMatch cable.
Up to two Sub1 or Sub2 powered bass
LPF modules can be powered by a single L1
w L1 a Pro32 via SubMatch connection.
t Power Input Cover: Prevents
LINE OUT 1 LINE OUT 2 LINE OUT EQ simultaneous use of the SubMatch Input
and Power Input. Slide the cover to reveal
FULL
the power input that is needed for setup.
e HPF o
y SubMatch Input: Connect the Sub to an
L1 Pro32 with a SubMatch cable.
i u Power Input: IEC power cord connection.
i USB Port: USB-C connector for Bose
service use and firmware updates.
Note: This port is not compatible with
Thunderbolt 3 cables.
o Line Output EQ: Select between FULL
bandwidth or a multi-purpose HPF when
using Line Outputs. Press the button to
switch EQ settings. The corresponding
LED will illuminate white while selected.
a Line Input EQ: Select between an
optimized EQ for an L1 Pro or a multi-
purpose LPF when using Line Inputs.
Press the button to switch EQ settings.
The corresponding LED will illuminate
white while selected.
s Signal/Clip Indicator: The LED will
illuminate green when a signal is present
and will illuminate red when the signal is
clipping or the Sub is entering limiting.
Reduce the level or signal volume to
SUBMATCH SUBMATCH prevent signal clipping or limiting.
THRU IN
d Level Control: Adjust the level of audio
output. The Level Control does not affect
the Line Outputs. The 12 o’clock position
is recommended when in use with an
L1 Pro32.
f Phase/Pattern Button: Adjust the polarity
of the Sub. Press the button to switch
polarity. The corresponding LED will
illuminate white while selected. Also
allows access to Cardioid mode when
using two identical Sub modules.

r t y u

PRO.BOSE.COM/L1 4 OF 6
 Product Dimensions

Left View Front View Right View Rear View

Bottom View Top View

Performance

Frequency Response (On-Axis)

140

130

120
SPL (dB)
SPL (dB)

110

100

90

80
20 100 1000 10000 20000
Frequency (Hz)
Frequency (Hz)

PRO.BOSE.COM/L1 5 OF 6
Architect and Engineer Specification
The sub shall be a single-driver, subwoofer with internally-supplied power amplification and active equalization
for multiple operating modes as follows:

The sub shall consist of a modular 10" x 18" (254 mm x 457 mm) RaceTrack low-frequency driver mounted in a
ported bass enclosure.

The nominal horizontal beamwidth of the loudspeaker shall be omnidirectional, with a –10 dB rear rejection
when in Cardioid mode. The nominal vertical coverage shall be 0°. The power amplification for transducers
shall be supplied by an integral single-channel onboard amplifier providing 1000 W for the low-frequency
transducer.

The onboard digital mixer shall consist of two input channels. Each input channel shall provide two
combination XLR or 1/4" TRS connectors (line-level) with selectable equalization presets for low-pass filter and
L1 optimization. Each input channel shall also provide an XLR balanced line-level connector with selectable
equalization presets for full bandwidth, high-pass filter, and S1 Pro optimization. The digital mixer shall provide
master output level control and phase/pattern control for positive polarity, negative polarity, and Cardioid
mode. The sub shall provide multi-pin SubMatch input and output connectors to receive power from L1 Pro32
and send power to another Sub1/Sub2 with a Bose SubMatch cable.
The enclosure of the sub shall be constructed of high-impact polypropylene and birch plywood. The sub shall
provide a pole-mount M20 threaded insert for use with the Bose Sub1/Sub2 Adjustable Speaker Pole. The sub
shall provide four interlocking feet on each side for stacking with one other Sub2.

The sub’s dimensions shall be 27.3" H × 12.5" W × 21.7" D (694 mm × 317 mm × 551 mm). Its net weight shall be
50.7 lbs (23.0 kg).

The sub shall be the Bose Sub2 portable powered bass module.

Safety and Regulatory Compliance

The Sub2 powered bass module complies with the following standards:
• UL/IEC/EN62368-1 Audio/Video, Information and Communication Technology Equipment
• Ecodesign Requirements for Energy Related Products Directive 2009/125/EC
• Radio Equipment Directive 2014/53/EU
• CAN ICES-3 (B)/NMB-3(B)
• FCC Part 15 Class B
Bose, L1, and ToneMatch are trademarks of Bose Corporation. All other trademarks are the property of their
respective owners.

For additional specifications and application information, please visit PRO.BOSE.COM.

Specifications subject to change without notice. 10/2021

PRO.BOSE.COM/L1 6 OF 6