SKU:2001712003

Instructions of LCD Hall Cullen Current

Button Instruction:
Voltage Power Electric Energy Meter
1. To control backlight
Function Introduction: When standby display, press ▲ key to turn on or turn off the
backlight. Backlight mode will be save when power-down.
1. This meter can be used to measure percentage and AH of 2. To clear current
remaining capacity, DC positive and negative bidirectional
current, DC voltage, DC positive and negative power, DC When standby display, to keep pressing ▲ key will clear current
to zero if no load is connected.(Note: if you don’t clear current
positive and negative bidirectional accumulated electric when no load connected, it will be inaccurate.)
energy.
2. Alarm flashing function: it will alarm and flash to draw your 3. To clear electric energy
attention when the real voltage is higher or lower than preset When standby display, to keep pressing █ key and release
alarm voltage and real current is higher than preset current. the key will clear positive and negative bidirectional
The preset voltage and current could be adjusted as you a c c u m u l a t e d e l e c t r i c e n e r g y.
need. It will also alarm and flash to draw your attention when 4. Setting parameters
the remaining capacity of battery is low and the battery icon When standby display, press █ key to switch menu in order.
will keep flashing that means you need to charge for your (1) “AH XXX.X” Setting Menu for rated capacity of battery
device. (2) “FU XXX.X” Setting Menu for fulfilling voltage when full
3. It will automatically fill the capacity of battery when it is full charged
voltage. (3) “HU XXX.X ” Setting Menu for over-voltage alarming
4. It has the function of clearing current and accumulated (4) “LU XXX.X” Setting Menu for low-voltage alarming
electric energy data and the function of storing data when (5) “HA XXX.X” Setting Menu for over-current alarming
power-down. Capacity of battery and accumulated electric
Setting method for rated capacity of battery:
energy will be saved automatically when power down.
(1) When standby, press █ key to switch to menu “AH XXX.X”
(2) The first digit on menu parameter will keep flashing, at
LCD Display Panel and Button: t h i s t i m e , p r e s s i n g ▲ k e y, t h e d i g i t w i l l p l u s 1 . A f t e r
finishing setting this digit, the next digit will automatically
flash when no any action in 5s. At this moment, pressing
Remaining capacity AH of battery ▲ key, the digit will plus 1,too. In this way, you will finish
setting 4 digits.
Remaining capacity of battery Menu/save key (3) Keeping pressing █ key, then release the key, the set
parameters will be stored, at this time, menu will flash
twice that means you have set successfully.
Eg. If you want to set battery’s rated capacity as 20AH, just
set the menu parameter as AH 020.0, then keep pressing
the █ key, finally release the key, you can make it stored
successfully.
Setting method for automatically filling voltage when full
charged(The same as setting method for rated capacity of
battery)
When standby, press █ key to switch to menu “FU XXX.X”,
press ▲ key to set parameters and keep pressing to save
set parameters. (Note: We suggest to set the voltage as the
voltage when full charged.)
By using the same setting method to set the value of over-
Backlight/ + key
Positive and negative power display voltage alarming, low voltage alarming and over current
alarming.
(Note: HU XXX.X LU XXX.X HA XXX.X, if the 3 parameters
Positive and negative accumulated display as 000.0, that means the alarming function is off,
electric energy display
factory setting is off. )
Technical Parameters:

LCD Hall Cullen Meter Current Voltage Power Electric Energy Meter
Technical Parameters
Model WLS-PVA200
black red yellow
Current measuring
range 200A

Current resolution 0.2A

Power supply range DC5〜90V
+
battery load or
Voltage measuring - Triangle icon on the
controller
DC0〜300V
range transformer will point to
load’s direction when
Voltage resolution 0.1A measuring positive lead.

Capacity measuring
range 0〜999AH
When the measured voltage is over DC 5-90V, this meter must
Power measuring be connected with three-wire system connection. A separate
range 0〜999KW power supply is needed for this meter. As the following picture
shows:
Electric energy Normally, the controller of electric bike has a 12V or 5V output,
measuring range 0〜999KWH
you can use it as power supply.
Measurement error ±1%
red
Refreshing speed 0.5S/time
Installing size 76.0mm * 39.5mm
DC5-100V
Diameter of power supply
Φ20mm
transformer
Working current Backlight on：10MA;Backlight off：4MA

black yellow

Wiring instructions:
+
battery load or
T h i s m e t e r, w i t h 3 w i r e s , a l l o w s t o b e p o w e r e d b y w i d e controller
- Triangle icon on the
voltage range and has a wide voltage measuring range. If the transformer will point to
measured voltage is DC 5-90V, you can use two-wire system load’s direction when
measuring positive lead.
connection to make it work, which is easy and simple. There
are 3 wires on the back of meter, as following:
The above pictures show the wiring method for those that
(1) Black wire is for power supply -
charging port and discharging port are the same one. If they
(2) Red wire is for power supply +.( Note: power supply range don’t share the same port, you need to make the positive of
must be DC 5-90V, or this meter will be burnt.) charging cable go through the hole of transformer.
(3) Yellow wire is for the input lead wire of the measured
voltage, it have to be connected to the lead wire of the
measured voltage.
Special Note:
1. Correct wiring method: Cullen meter display positive current
When the measured voltage is DC 5-90V, this meter can be when discharging and display negative current when
connected with two-wire system connection. Making the red charging. If not, that means you connected the transformer
wire and yellow wire in parallel and then connect it to the
positive of battery. As the following picture shows: ( Note: if in wrong direction.
you input voltage is higher than 80V, please add ventilation 2. Newly installed Cullen meter need to clear current when
and cooling; and also we suggest to add separate power no load connected.
supply for this meter.) 3. When the newly installed Cullen meter has been set battery
capacity and automatically filling the voltage when fully
charged, you need to make battery fully charged again,
then it can display remaining capacity.
4. Please keep this meter away from water, or it will be burnt.