3/16/23, 12:06 PM Midterm Exam: Attempt review

Home / My courses / UGRD-IT6224-2223T / MIDTERM EXAMINATION / Midterm Exam

Started on Thursday, 16 March 2023, 10:44 AM

Question 1
Correct

Mark 1.00 out of 1.00

What is the default maximum amount of bandwidth that EIGRP uses for EIGRP control information considering an interface configured for
128 kbps?

Select one:
a. 64 kbps

b. 32 kbps

c.
  128 kbps

d. 16 kbps

Your answer is correct.

trimestralexam.amaesonline.com/2223/mod/quiz/review.php?attempt=92281&cmid=3074&showall=1#question-92562-50 1/18
3/16/23, 12:06 PM Midterm Exam: Attempt review

Question 2

Correct

Mark 1.00 out of 1.00

Which EIGRP parameter must match between all routers forming an EIGRP adjacency?

Select one:
a. administrative distance

b. autonomous system number

c. variance

d.   hello timer

e.   hold timer

Your answer is correct.

Question 3
Correct

Mark 1.00 out of 1.00

Which protocol number is used to indicate that an EIGRP packet is encapsulated in an IP packet?

Select one:
a. 6

b. 88

c. 17

d. 89

Your answer is correct.

Question 4

Correct

Mark 1.00 out of 1.00

IGRP   One of the four distance vector IPv4 IGPs refers as First generation Cisco proprietary protocol (obsolete
and replaced by EIGRP)

trimestralexam.amaesonline.com/2223/mod/quiz/review.php?attempt=92281&cmid=3074&showall=1#question-92562-50 2/18
3/16/23, 12:06 PM Midterm Exam: Attempt review

Question 5

Correct

Mark 1.00 out of 1.00

The OSPF Type 1 packet is the Hello  packet.

Question 6
Incorrect

Mark 0.00 out of 1.00

Routing Information Protoco  used to distribute routing information

Question 7
Correct

Mark 1.00 out of 1.00

Which routing protocol uses both bandwidth and delay to determine the best pathway to reach a remote network?

Select one:
a. OSPF

b. EIGRP

c. RIP

d. IS-IS

Your answer is correct.

Question 8
Correct

Mark 1.00 out of 1.00

Which classless routing protocol supports VLSM and CIDR, supports manual route summarization, and uses the multicast address 224.0.0.9?

Select one:
a. OSPF

b. RIPv1

c. EIGRP

d. RIPv2

Your answer is correct.

trimestralexam.amaesonline.com/2223/mod/quiz/review.php?attempt=92281&cmid=3074&showall=1#question-92562-50 3/18
3/16/23, 12:06 PM Midterm Exam: Attempt review

Question 9

Correct

Mark 1.00 out of 1.00

The OSPF hello timer has been set to 15 seconds on a router in a point-to-point network. By default, what is the dead interval on this router?

Select one:
a. 60 seconds

b. 30 seconds

c.   15 seconds

d. 45 seconds

Your answer is correct.

Question 10
Correct

Mark 1.00 out of 1.00

In the command router eigrp 100, what does the value 100 represent?

Select one:
a. the metric

b. the administrative distance

c. the router ID

d. the autonomous system number

Your answer is correct.

trimestralexam.amaesonline.com/2223/mod/quiz/review.php?attempt=92281&cmid=3074&showall=1#question-92562-50 4/18
3/16/23, 12:06 PM Midterm Exam: Attempt review

Question 11

Correct

Mark 1.00 out of 1.00

What is an advantage of OSPF compared to RIP?

Select one:
a. less complexity

b. fast convergence

c. less CPU processing

d. low memory requirements

Your answer is correct.

Question 12
Correct

Mark 1.00 out of 1.00

How can a network administrator reduce SPF overhead on OSPF routers?

Select one:
a. Decrease the hello timer intervals.

b.   Increase the number of neighbor adjacencies.

c. Reduce the interface delay values.

d. Implement multiple areas of OSPF.

Your answer is correct.

Question 13
Correct

Mark 1.00 out of 1.00

OSPF features, Efficient  Routing changes trigger routing updates (no periodic updates). It uses the SPF algorithm
to choose the best path.

trimestralexam.amaesonline.com/2223/mod/quiz/review.php?attempt=92281&cmid=3074&showall=1#question-92562-50 5/18
3/16/23, 12:06 PM Midterm Exam: Attempt review

Question 14

Correct

Mark 1.00 out of 1.00

RIPv2  One of the four distance vector IPv4 IGPs refers as Simple distance vector routing protocol

Question 15
Correct

Mark 1.00 out of 1.00

Which bandwidth value is used when calculating the EIGRP metric of a route?

Select one:
a. the slowest bandwidth of all outgoing interfaces between the source and destination

b. the fastest bandwidth of all interfaces on the router 

c. the fastest bandwidth of all outgoing interfaces between the source and destination

d. the slowest bandwidth of all interfaces on the router 

Your answer is correct.

Question 16

Correct

Mark 1.00 out of 1.00

Speed of convergence  Routing protocols characteristic defines how quickly the routers in the

network topology share routing information and reach a state of consistent knowledge.

Question 17
Incorrect

Mark 0.00 out of 1.00

Link-state routing protocols apply Dijkstra's algorithm  to calculate the best path route.

trimestralexam.amaesonline.com/2223/mod/quiz/review.php?attempt=92281&cmid=3074&showall=1#question-92562-50 6/18
3/16/23, 12:06 PM Midterm Exam: Attempt review

Question 18

Correct

Mark 1.00 out of 1.00

What is a disadvantage of using EIGRP automatic summarization?

Select one:
a.   It increases the size of routing updates.

b.
  It prevents convergence of the routing table.

c.   It increases the number of routes in the routing table.

d. It creates inconsistent routing when the network has discontiguous networks.

Your answer is correct.

Question 19
Correct

Mark 1.00 out of 1.00

What loop prevention technique is implemented by distance vector routing protocols?

Select one:
a. split horizon

b. loop guard

c. poison reverse

d. gateway of last resort

Your answer is correct.

Question 20
Incorrect

Mark 0.00 out of 1.00

Classful  Routing protocols characteristics do not include the subnet mask and cannot support VLSM.

trimestralexam.amaesonline.com/2223/mod/quiz/review.php?attempt=92281&cmid=3074&showall=1#question-92562-50 7/18
3/16/23, 12:06 PM Midterm Exam: Attempt review

Question 21

Correct

Mark 1.00 out of 1.00

Dynamic routing protocols    are used by routers to facilitate the exchange of routing

information between routers.

Question 22
Correct

Mark 1.00 out of 1.00

A router is running an EIGRP process and obtaining updates from other routers. What is an indication within the routing table that a route is
a candidate for a default route?

Select one:
a. D

b. 170

c. *

d. 90

e. EX

Your answer is correct.

Question 23
Correct

Mark 1.00 out of 1.00

Which operation feature is different between EIGRP and RIP?

Select one:
a.
  EIGRP sends broadcast updates to neighbors.

b. EIGRP uses periodic update timers.

c. EIGRP has a metric of hop count.

d. EIGRP stores all routes learned from neighbors in a topology table.

Your answer is correct.

trimestralexam.amaesonline.com/2223/mod/quiz/review.php?attempt=92281&cmid=3074&showall=1#question-92562-50 8/18
3/16/23, 12:06 PM Midterm Exam: Attempt review

Question 24

Correct

Mark 1.00 out of 1.00

Which interior routing protocol uses protocol-dependent modules (PDMs)?

Select one:
a. RIP

b. EIGRP

c.   IS-IS

d. OSPF

Your answer is correct.

Question 25
Correct

Mark 1.00 out of 1.00

OSPF features Classless  OSPFv2 is classless by design; therefore, it supports IPv4 VLSM and CIDR.

Question 26

Correct

Mark 1.00 out of 1.00

Which OPSF packet contains the different types of link-state advertisements?

Select one:
a. LSR

b. DBD

c. hello

d. LSU

Your answer is correct.

trimestralexam.amaesonline.com/2223/mod/quiz/review.php?attempt=92281&cmid=3074&showall=1#question-92562-50 9/18
3/16/23, 12:06 PM Midterm Exam: Attempt review

Question 27

Correct

Mark 1.00 out of 1.00

Which algorithm is used by the OSPF routing process to construct the SPF tree on a router?

Select one:
a. path vector protocol

b. Bellman-Ford algorithm

c. DUAL algorithm

d. Dijkstra's algorithm

Your answer is correct.

Question 28
Correct

Mark 1.00 out of 1.00

The wildcard mask that is used to advertise exactly the network 192.168.160.0 with subnet mask 255.255.240.0 is
0.0.15.255 

Question 29
Correct

Mark 1.00 out of 1.00

Which routing protocol uses the DUAL algorithm and sends multicast messages to propagate routing updates?

Select one:
a. OSPF

b. RIPv1

c. EIGRP

d. RIPv2

Your answer is correct.

trimestralexam.amaesonline.com/2223/mod/quiz/review.php?attempt=92281&cmid=3074&showall=1#question-92562-50 10/18
3/16/23, 12:06 PM Midterm Exam: Attempt review

Question 30

Correct

Mark 1.00 out of 1.00

Which statement is correct about multiarea OSPF?

Select one:
a. OSPF can consolidate a fragmented OSPF area into one large area.

b.
  OSPF multiarea increases the frequency of SPF calculation.

c. Arranging routers into areas partitions a large autonomous system in order to lighten the load on routers.

d. All routers are in one area called the backbone area (area 0).

Your answer is correct.

Question 31
Correct

Mark 1.00 out of 1.00

A network technician issues the following commands when configuring a router:

R1(config)# router ospf 11

R1(config-router)# network 10.10.10.0 0.0.0.255 area 0

Select one:
a. the area number where R1 is located

b. the autonomous system number to which R1 belongs

c. the administrative distance that is manually assigned to R1

d. the OSPF process ID on R1

e. the cost of the link to R1

Your answer is correct.

trimestralexam.amaesonline.com/2223/mod/quiz/review.php?attempt=92281&cmid=3074&showall=1#question-92562-50 11/18
3/16/23, 12:06 PM Midterm Exam: Attempt review

Question 32

Correct

Mark 1.00 out of 1.00

When would the network administrator use the ip bandwidth-percent eigrp as-number percent command?

Select one:
a. when there is a low bandwidth connection

b. when the connection is on a shared medium

c. when the connection is serial instead of Ethernet

d. when the link is always busy

Your answer is correct.

Question 33
Correct

Mark 1.00 out of 1.00

Which multicast address does an EIGRP-enabled router use to send query packets?

Select one:
a. 224.0.0.5

b. 224.0.0.12

c. 224.0.0.10

d. 224.0.0.9

Your answer is correct.

trimestralexam.amaesonline.com/2223/mod/quiz/review.php?attempt=92281&cmid=3074&showall=1#question-92562-50 12/18
3/16/23, 12:06 PM Midterm Exam: Attempt review

Question 34

Correct

Mark 1.00 out of 1.00

A network administrator configures a loopback interface as the OSPF router ID with the IP address of 192.168.1.1/30. What could be the
consequence of using this 30-bit mask for the loopback interface?

Select one:
a.   The interface is not enabled for OSPF.

b. OSPF routers must also be configured with a router priority value.

c. Older routers do not recognize the router-id command.

d. This loopback interface may be advertised as a reachable network.

Your answer is correct.

Question 35
Correct

Mark 1.00 out of 1.00

What is the purpose of the EIGRP Null0 summary route?

Select one:
a. to ensure that all traffic destined for individual subnets uses one single best path

b. to enhance security by hiding all internal networks that are included in a summary route

c. to reduce bandwidth consumption  for traffic that is leaving the network

d. to prevent routing loops for destination networks which do not actually exist but are included in a summary route

Your answer is correct.

Question 36
Correct

Mark 1.00 out of 1.00

Hello  used to form an EIGRP neighbor relationship

trimestralexam.amaesonline.com/2223/mod/quiz/review.php?attempt=92281&cmid=3074&showall=1#question-92562-50 13/18
3/16/23, 12:06 PM Midterm Exam: Attempt review

Question 37

Correct

Mark 1.00 out of 1.00

Which routing protocol was designed by the International Organization for Standardization (ISO)?

Select one:
a. EIGRP

b. IS-IS

c. OSPF

d. RIP

Your answer is correct.

Question 38
Correct

Mark 1.00 out of 1.00

OSPF features, Fast convergence  It quickly propagates network changes

Question 39

Correct

Mark 1.00 out of 1.00

Resource Usage   Routing protocols characterisitics includes the requirements of a routing protocol such

as memory space (RAM), CPU utilization, and link bandwidth utilization. 

Question 40
Correct

Mark 1.00 out of 1.00

  EIGRP   One of the four distance vector IPv4 IGPs refers as Advanced version of distance vector routing

trimestralexam.amaesonline.com/2223/mod/quiz/review.php?attempt=92281&cmid=3074&showall=1#question-92562-50 14/18
3/16/23, 12:06 PM Midterm Exam: Attempt review

Question 41

Correct

Mark 1.00 out of 1.00

Which command will limit the bandwidth that is used by EIGRP process 1 to 20%? ip bandwidth-percent eigrp 

Question 42
Correct

Mark 1.00 out of 1.00

Implementation and Mainten   Routing protocols characteristics describes the level of knowledge that is required for a network
administrator to implement and maintain the network based on the routing protocol deployed.

Question 43

Correct

Mark 1.00 out of 1.00

Which routing protocol uses the Diffusing Update Algorithm to install routes into the routing table?

Select one:
a.   BGP

b. OSPF

c. EIGRP

d. RIP

Your answer is correct.

trimestralexam.amaesonline.com/2223/mod/quiz/review.php?attempt=92281&cmid=3074&showall=1#question-92562-50 15/18
3/16/23, 12:06 PM Midterm Exam: Attempt review

Question 44

Correct

Mark 1.00 out of 1.00

Two routers, R1 and R2, have established an EIGRP neighbor relationship, but there is still a connectivity problem. Which issue could be
causing this problem??

Select one:
a. an access list that is blocking advertisements from other networks

b. a process ID mismatch

c. automatic summarization that is disabled on both routers

d. an authentication mismatch

Your answer is correct.

Question 45
Correct

Mark 1.00 out of 1.00

A network administrator is analyzing the differences between an EIGRP hold timer and EIGRP hello interval. What statement is valid about
EIGRP hello and hold timers?

Select one:
a. EIGRP hello intervals and hold timers must match between EIGRP neighbors to form an EIGRP adjacency.

b. EIGRP hello intervals should be less than or equal to EIGRP hold timers.

c. EIGRP hello timers specify the maximum time that the router should wait to receive the next hello.?

d. EIGRP hold timers specify the minimum time that the router should wait to send the next hello.

Your answer is correct.

Question 46
Correct

Mark 1.00 out of 1.00

The command clear ip ospf process    forces a router with a new or changed router ID to form new adjacencies.

trimestralexam.amaesonline.com/2223/mod/quiz/review.php?attempt=92281&cmid=3074&showall=1#question-92562-50 16/18
3/16/23, 12:06 PM Midterm Exam: Attempt review

Question 47

Correct

Mark 1.00 out of 1.00

What address and wild card mask can be used to enable EIGRP for only the subnet 192.168.100.192 255.255.255.192?

Select one:
a. 192.168.100.192 0.0.0.15

b. 192.168.100.192 0.0.0.127

c. 192.168.100.192 0.0.0.7

d. 192.168.100.192 0.0.0.63

Your answer is correct.

Question 48
Correct

Mark 1.00 out of 1.00

RIPv1  One of the four distance vector IPv4 IGPs refers as the First generation legacy protocol

Question 49

Correct

Mark 1.00 out of 1.00

used to confirm the reliable delivery of a packet.

Select one:
a. REPLY 

b. UPDATE 

c. ACKNOWLEDGEMENT 

d. HELLO 

Your answer is correct.

trimestralexam.amaesonline.com/2223/mod/quiz/review.php?attempt=92281&cmid=3074&showall=1#question-92562-50 17/18
3/16/23, 12:06 PM Midterm Exam: Attempt review

Question 50

Correct

Mark 1.00 out of 1.00

Scalability  Routing protocols characteristics defines how large a network can become, based on the
routing protocol that is deployed. 

◄ Prelim Lab Exam

Jump to...

Midterm Lab Exam ►

trimestralexam.amaesonline.com/2223/mod/quiz/review.php?attempt=92281&cmid=3074&showall=1#question-92562-50 18/18