Danfoss IOM APP 11 13 L

MAKING MODERN LIVING POSSIBLE
Lenntech
[email protected]
[email protected] Tel.
Tel. +31-152-610-900
+31-152-610-900
www.lenntech.com
www.lenntech.com Fax.
Fax.+31-152-616-289
+31-152-616-289
User manual
Installation, Operation and

Maintenance Manual
APP pumps (APP 11-13)
APP 11-13
User manual Installation, Operation and Maintenance APP Pumps (APP 11-13)
Table of Contents Validity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

EU Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.2 Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.3 Manufacturer and customer service address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2. Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.1 General information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.2 Preferred system design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.3 Commissioning and servicing the unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.4 Adhere to the following important points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.5 In case of doubt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3. Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3.1 Approved applications and operational limits for the pumps . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3.2 Application range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3.3 Electric motor data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3.4 Noise and vibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3.5 Dimension drawings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3.6 Space requirement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3.7 Filtration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.8 Properties of water . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.9 Air bubbles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.10 Chemicals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4. Arrival inspection, transportation, handling, lifting and storage . . . . . . . . . . . . . . . . . . . . . . . . . . 9

4.1 Arrival inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4.2 Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4.3 General safety information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4.4 Transport and handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4.5 Return to supplier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4.6 Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
5. Installation and commissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

5.1 Important dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
5.2 Cleanliness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
5.3 Fluid temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
5.4 Electrical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
5.5 Local regulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
5.6 Pre mounting checklist, based on Danfoss preferred system design . . . . . . . . . . . . . . . . . . . . . 11
5.7 Lifting and positioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
5.8 Mount the different equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
5.9 Electrics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
5.10 Instrumentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
5.11 Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
5.12 Ensure free flow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
5.13 Verify setting of safety/relief valves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
5.14 Flush the pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
5.15 Bleed and remove air from the pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
5.16 Verify direction of rotation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
5.17 Commissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
5.18 Check the filter condition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
5.19 Instruct operator and maintenance personnel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
6. Operation of pump unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

6.1 General safety information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
6.2 What to listen and look for . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
2 180R9264 / IOM APP Pumps - v03 / 11.2013

7. Maintenance and service of the pump unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

7.2 Service and inspection interval for the pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
7.3 Shut down of the system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
7.4 Disassembling and assembling the pump unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
7.5 Assembling the pump unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
7.6 Procedure for mounting the pump onto the electric motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
7.7 Getting the pump unit back into operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
7.8 Storage of the pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
8. Troubleshooting and scrapping criteria . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

8.2 Operational conditions which can cause pump failures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
8.3 Mechanical failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
8.4 Electrical failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
8.5 Responsibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
8.6 Scrapping criteria . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Subject index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Appendices for Installation, Operation and Maintenance Manual
1. Data sheet for APP 11-13 pumps (521B1215) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2. APP pump instruction APP 11-13 (180R9223) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3. IOM Electric motors (180R9230) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
4. Recommended service intervals for APP pumps (80R9199) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
5. APP parts list (521B0941) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
6. Trouble shooting guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
7. Right and wrong (180R9042) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
180R9264 / IOM APP Pumps - v03 / 11.2013 3

Validity This manual is valid for APP pumps with the following code numbers/serial numbers:
APP 11/1200 Code no. 180B3212

Serial no. 02
APP 11/1500 Code no. 180B3211
Serial no. 02
APP 13/1200 Code no. 180B3214
Serial no. 02
APP 13/1500 Code no. 180B3213
Serial no. 02
4 180R9264 / IOM APP Pumps - v03 / 11.2013

EU Declaration of Conform-
ity
180R9264 / IOM APP Pumps - v03 / 11.2013 5

1. Introduction 1.1 General

The APP pumps and pump units are manufac- • I f any changes are made without written
tured by Danfoss A/S, and are sold and marketed approval the warranty will automatically
by a net of authorized distributors world wide. become void.
This manual contains the necessary instructions It is important that these instructions are
for the installation, operation and service of the always available to the personnel concerned.
pumps used in a Sea Water Reverse Osmosis
(SWRO) system or Brackish Water Reverse
Osmosis (BWRO) system. 1.2 Symbols
In case the pump delivered is ATEX certified, the

additional ATEX instruction must also be read.
Indicates something to be noted by the
The APP pumps must not be used for other reader
purposes than those recommended and
specified without first consulting your local
pump distributor. Indicates a situation which will or could
result in damage to the pump and its
function
Use of the pump in other applications that are Indicates a situation which will or could
not suitable for the pump unit can cause result in personal injury and/or damage
damages to the pump unit, with risk of personal to the pump
injury.
Electrical hazard - Indicates a high-

voltage warning
All personnel being responsible for operation

and maintenance of the pump unit must read Safety glasses required
and fully understand these instructions,
especially the section “Safety”, before:
• Transportation of the pump unit Hearing protection required

• Lifting the unit
• Installing the pump unit
• Connecting the pump unit to the water
system Safety shoes required
• Connecting the electric motor and instru-
mentation
• Commissioning the unit
• Servicing the pump unit, mechanical and Safety helmet required
electrical parts
• Decommissioning the pump unit
!
Protective
The pump must always be installed and used in garments Protective garments
accordance with existing national/local must be worn must be worn
sanitary, safety regulations and laws.
It is the responsibility of the safety officer or

the chief operator to assure compliance with all Danger HOT.
local regulations that are not taken into Do not touch
account in this manual.
Electrical Electrical hazard

hazard
Changing the pumps’ or pump units’ opera-

tional limits and hardware:
• hanges to the delivered pump or motor

C
pump unit may only be done with a written
approval from Danfoss High Pressure Pumps.
• Operation outside the Danfoss specifications
requires a written approval from Danfoss
High Pressure Pumps.
6 180R9264 / IOM APP Pumps - v03 / 11.2013

1.3 Manufacturer and customer service

address
Danfoss A/S Your local Danfoss pump distributor can be

Danfoss High Pressure Pumps found on our homepage.
RO Solutions
Nordborgvej 81, D25 Data sheets and instructions on all accessories
DK-6430 Nordborg are available on www.ro-solutions.danfoss.com
Denmark
EC Declaration of Conformity can be found on
Telephone: +45 7488 4024 page 5.
Fax: +45 7445 3831
Email: [email protected]
Homepage: www.ro-solutions.com
2. Safety
2.1 General information Under certain operational conditions the surface

Dangers that can arise from not following the of the pump can be above 60°C / 140°F. Under
instructions: these conditions the pump must be labelled with
a “Danger Hot” sign.
When the pump or pump unit is managed by
untrained personnel, there is a danger of: When using an electric motor, the motor must
always be supplied with adequate cooling
• Death or fatal injuries ventilation.
• Costly damages and claims
When using an electric motor together with a
VFD, the motor must be designed for operation
Electrical with a VFD.
hazard
All electrical installation work must only be VFD operation may increase the temperature
carried out by authorized personnel in inside the electric motor if the motor is not
accordance with EN60204-1 and/or local designed for VFD operation. This can damage
regulations. the motor and cause unintended breakdown.
It is recommended to install a lockable circuit

breaker to avoid inadvertent starting and/or
electrical hazard. The lockable circuit breaker
must be used during installation, operation and Before start-up, the settings for all protective
maintenance. devices, such as sensors/switches and safety
valves must be verified and free flow from safety
It is recommended to place a local safety switch valves must be ensured.
nearby the pump, enabling service personnel to
cut power for the electric motor.
Protect the motor and other electrical equip-

ment from overloads with suitable equipment. All pipe and hose connections must be stress-
free mounted, securely fastened to the pump
In case the pump delivered is ATEX certified, the and well supported. Improper installation will or
additional ATEX instruction must also be read. can result in personal injury and/or damage to
the pump.
!
Protective
garments Use of this manual does not relieve operation
must be worn and maintenance personnel of the responsibil-
ity of applying good judgment when operating
and maintaining the pump and its compo-
nents.
Always wear suitable safety clothing when
handling the pump.
2.2 Preferred system design
When working near the pump system, safety Danfoss recommends to build systems with a
shoes, safety glasses, hearing protection and high degree of safety. Danfoss preferred system
safety helmet must always be worn. design and P&ID are found in appendix 1, Data
sheet, and appendix 2, Instruction.
180R9264 / IOM APP Pumps - v03 / 11.2013 7

It is always the system builders´ responsibility • o not try to lift the pump unit manually;
D
that the system design does not cause any kind most of the pumps weigh more than
of hazard and is adapted to local regulations and 20 kilos, see specific weight for the pump
standards. in the appendix 1, Data sheet.
• Always bleed the pump prior to initial
Proper installation, proper start up and shut- start-up.
down devices as well as high-pressure protection • Do not mount the pump without the bell
equipment is essential. housing and a flexible coupling.
• Do not try to start the unit before the
system components are mounted, bleeded
2.3 Commissioning and servicing the unit and adjusted.
It is recommended that commissioning and • Flush the system throughly before
servicing are carried out by a minimum of two connecting the pump or pump unit.
people, where one is acting as a supervisor. • Check rotation direction of the motor
before mounting the pump.
2.4 Adhere to the following important

points 2.5 In case of doubt
Please contact Danfoss A/S in case of doubt.
• efore using the pump/pump unit it is very
B Contact information is listed in section 1.3,
important to read and understand this user Manufacturer and customer service address.
manual.
3. Technical data 3.2 Application range

See appendix 1, Data sheet.
3.3 Electric motor data

See recommended motor in appendix 1, Data
sheet or appendix 3, IOM for motors. The motors
mentioned are the most common used motors
by Danfoss High Pressure Pumps.
3.4 Noise and vibration

Noise level for a pump unit with a ”standard”
motor measured according to EN ISO 3744: 2010,
see appendix 1, Data sheet. Possibilities to
reduce noise and vibration are described in the
same Data sheet.
3.1 Approved applications and operational

limits for the pumps 3.5 Dimension drawings
The pump and the pump units are designed for Dimensions of the different pumps can be found
the use in a Sea Water Reverse Osmosis (SWRO) in appendix 1, Data sheet.
or Brackish Water Reverse Osmosis (BWRO)
systems and Brackish Water Reverse Osmosis
(BWRO) system. 3.6 Space requirement
When doing service or replacing the complete
The APP pumps must not be used for other pump unit, it is recommended to have sufficient
purposes than those recommended and space available around the pump in order to
specified without first consulting your local ensure easy access. Sufficient space means at
pump distributor. least 1 meter/40 inches around the pump. When
working with high pressures, it is important to
have the right space available around the pump
as stated in the safety requirements.
Use of the pump in other applications not

suitable for the pump unit can cause damages
to the pump unit, with risk of personal injury.
For system integration of the pump, please see

appendix 1, Data sheet and appendix 2,
Instruction.
8 180R9264 / IOM APP Pumps - v03 / 11.2013

3.7 Filtration 3.9 Air bubbles

(10µm absolute [ß10 ≥ 5000]) Large bubbles in a pressurised RO system can
Requirements are specified in appendix 1, Data result in damage to piping, equipment and the
sheet and in appendix 2, Instruction. pump.
Danfoss recommends not to build a filter bypass All air must be bleeded from both the low-
function or to use filters with an integrated pressure and high-pressure side before the RO
bypass. If the above recommendation is not system is pressurised. Special consideration
followed the warranty for the pump will should be given in order to minimize air bubbles
automatically become void. in the feed flow. Air bubbles can cause cavitation.
It should be possible to monitor the condition of

the filter via the differential/delta pressure across
the filter.
3.10 Chemicals
Using insufficient filtration or a filter bypass The pump should not be exposed to any
can cause a failure or decreased service life of chemicals as it can result in damage to piping,
the pump. equipment and internal parts in the pump.
3.8 Properties of water

It is recommended NOT to use the pumps in feed
water concentrations higher than 50,000 ppm
TDS without consulting your local Danfoss pump
distributor.
4. Arrival inspection, 4.1 Arrival inspection 4.4 Transport and handling

transportation, The pump is packed in a cardboard or wood box Small pumps which have a weight below 20 kilos
handling, lifting and with plugs in the port connections to protect the (weight can be found in appendix 1, Data sheet).
storage pumps from damage during transportation. can be handled by hand if they are not mounted
together with an electric motor. The weight of a
When the shipment has arrived it is important to small pump with a motor will be above 20 kilos.
check the pump for any damages. The name
plate/type designation must be in accordance
with the delivery note and your order.
In case of damage and/or missing parts, a report

should be documented and presented to the
carrier at once.
4.2 Warning
Before any lifting operation is performed,
environmental conditions must be taken into
consideration (Ex-rated areas, wind speed, wet/
dry conditions, lifting height, etc.).
4.3 General safety information

Personnel involved in lifting and transporting the
equipment (see Safety, chapter 2) must be
trained in handling and in safety procedures for
lifting heavy loads. Many of the pumps and
pump units weigh more than 20 kilos, which
requires lifting slings and suitable lifting devices;
e.g. an overhead crane or industrial truck to be
used as minimum.
180R9264 / IOM APP Pumps - v03 / 11.2013 9

Pumps which have a weight above 20 kilos (see Wrong lifting:

appendix 1, Data sheet) must be handled by
using lifting eyes and slings.
When lifting the pump unit, one sling must be

attached to the electric motor and one sling
around the pump.
Some motors and pumps have specific lifting

eyes.
Do not use connections/nozzles for lifting!

Do not use only one sling!
Make sure that the unit/load is balanced before

Never use only one sling and make sure the lifting. The centre of the mass varies from pump/
slings does not slip off the pump. pump unit size to pump/pump unit.
When the pump is mounted together with an How to mount the pump and the electric motor
electric motor, the pump unit always weigh more correctly, see appendix 1, Data sheet or appendix
than 20 kilos and must be handled by using 2, Instruction.
slings around the pump unit.
See below examples of where to/not to attach

the lifting slings on the pump unit: Incorrect lifting can result in personal injury
and/or damage to the pump unit, see appendix
Correct lifting with 2 separate slings: 2, Instruction.
4.5 Return to supplier

Please see maintenance chapter 7.
4.6 Storage
Each pump is tested before shipment, and will
therefore contain water. For storage temperature
and frost protection see appendix 2, Instruction.
The pumps are NOT delivered frost protected

from the factory.
10 180R9264 / IOM APP Pumps - v03 / 11.2013

5. Installation and
commissioning
5.1 Important dimensions 5.4 Electrical data
Physical dimensions and connections of the Check voltage, current frequency and rated
pump unit are described in appendix 1, Data power on the electric motor and VFD settings on
sheet. the name plate placed on both the motor and
the VFD.
5.2 Cleanliness
It is very important that the tubes and pipes are 5.5 Local regulations
completely clean: no dirt, chips or burrs are Commissioning must always be done in
allowed. Flush all piping before connecting the accordance with valid regulations and local
high-pressure pump to ensure the system is standards.
clean. Internal surfaces of the piping must not be
corroded. If dirt or rust is not removed, the pump
and the valves can be damaged. In worst case
the pump can be damaged beyond repair!
5.3 Fluid temperature

Before start-up, the fluid and pump housing
temperature must be within the specified
temperature range listed see appendix 1, Data
sheet.
Schematic 1: Recommended system design
Media filter
PI
M
9 3 8
PI 1 PI 1 PI PT PI
Feed 2
7 Permeate
4
5
6 PT
Brine
180R9264 / IOM APP Pumps - v03 / 11.2013 11

5.6 Pre mounting checklist, based on Danfoss preferred system design
Table 1: C
heck points when assembling and commissioning system
Check points Comment OK ?

CP1 Ensure that the environmental conditions are safe. See Arrival inspection,
transportation, handling,
lifting and storage, chapter 4.
CP2 Minimum and maximum start-up temperature for fluid and See Data sheet or Instruction,
pump. appendices 1 and 2.
CP3 Filtration condition (10 µm absolute (ß10 ≥ 5000) See Danfoss requirements in
Data sheet and Instruction,
appendices 1 and 2
CP4 Power supply for electric motor and VFD. See Data sheet for the used
motor and VFD.
CP5 Safety circuit / breaker must be sized for the motor and See Data sheet for the used
environment (corrosion and humidity) safety circuit.
CP6 Bolts and screws must conform to environmental conditions
as well as fluid and torque requirements.
CP7 Instrumentation, pressure switch should be designed to See Data sheet for the used
conform to the environment (corrosion and humidity). equipment.
CP8 Check the factory settings of the safety/relief valves or See Data sheets for the used
pressure relief valves (8 & 9). valves.
CP9 Check the settings of the pressure transmitter/switch (3) set See Data sheet or Instruction,
at min. inlet pressure. appendices 1 and 2.
CP10 Check that all pressure indicators (PI) are selected to be able Scaling should at least be 1 Bar
to measure the system pressure range. or more precise.
CP11 Check coupling distance ( air gab – movement of the spider ) 3 – 5 mm
CP12 Check correct connections on the pump ( in & outlet)
CP13 Check piping for possible air gaps.
5.7 Lifting and positioning 5.9 Electrics

Lift the pump unit onto base (Remember All electrical installation work must be carried
vibration dampeners, if needed). Fasten the out by authorized personnel in accordance with
motor to the base. EN60204-1 and/or local regulations. (see also
Safety, chapter 2)
See also chapter 4, Arrival inspection, transporta-
tion, handling, lifting and storage. Turn off the safety circuit breaker and lock it.
Mount the power cable on the electric motor.

5.8 Mount the different equipment
(connections, pipes, tubes, check and safety/relief If a VFD is used, adjust the protective motor
valves, etc.) switch/VFD to the current limits found on the
name plate of the electric motor.
• T he hard piping and flexible hoses used,
must be of proper design and must be
installed in accordance with the manufactur- 5.10 Instrumentation
er’s recommendations. (see also Data sheet The pressure switch/sensor should be mounted
for Hose and hose fittings and Instruction for as close to the pump as possible. It is recom-
Assembling Hose kit - both available on mended to test the pressure/sensor switch via an
www.ro-solutions.danfoss.com). instrumentation manifold.
• Misalignment of the hard pipes may give
unintended stress on the pump port Mount the pressure switch/sensors according to
connections and may damage the pump. the manufacturer’s instructions.
• Prevent excessive external pipe load.
• Do not connect piping by applying external
force (use of wrenches, crane, etc.) Piping 5.11 Connections
must be aligned without residual stress. Mount and tighten connections and check
• Do not mount expansion joints so that their valve(s) as specified.
force applies internal pressure on the pump
connections.
12 180R9264 / IOM APP Pumps - v03 / 11.2013

5.12 Ensure free flow 5.17 Commissioning

Ensure free flow from the safety/relief valves 8 • Close all the bleeding and draining plugs.
and 9 (figure 1, item 5.6). A blocked safety/relief • Open the pressure valve at the brine site.
valve can cause excessive build-up of pressure • Switch the safety circuit breaker on for both
and thereby cause dangerous situations and motor(s) and VFD(s).
damage to the whole system. • Start the feed pump.
• Start the high-pressure pump.
• If a VFD or a soft starter is used a ramp up
5.13 Verify setting of safety/relief valves time of minimum 10 seconds is required to
Make sure, the safety/relief valves 8 and 9 are avoid damage of the pump.
placed correctly. • Monitor the inlet and outlet pressure of the
high-pressure pump and look for leakages.
Check the pressure settings on the name plates • Check the function of the pressure
of the safety/relief valves. If they are within indicators by slowly closing the valves. The
specifications, you can continue. pump unit should stop when the minimum
inlet pressure and maximum outlet
pressure has been reached.
5.14 Flush the pump • Adjust the pressures to the specified inlet
Fully open the pressure valve at the brine outlet. and outlet pressure for the system and let
the pump unit run until the electric motor
Close all the bleeding and draining plugs on the and pump temperature is stable.
high-pressure pump. • If the system is running within the system
design limits, the system is released for
Start the feed pump and ensure free flow to the operation.
high-pressure pump.
5.15 Bleed and remove air from the pump

Open the bleeding plugs. Keep the plugs open 5.18 Check the filter condition
until the high-pressure pump is bleeded. Evaluate contamination found in filter, replace
filter elements, if necessary.
5.16 Verify direction of rotation

The direction of rotation must always follow the
arrow. The arrow is placed on the pump or pump
unit. 5.19 Instruct operator and maintenance
personnel
Check the direction of rotation before mounting Before using the pump/pump unit, the personnel
the pump. must be instructed in using the pump/pump
unit, its function, components, documentation
Unlock the safety circuit breaker. Start the motor and safety.
for 1 second and observe the direction of
rotation either looking at the fan of the motor or Danfoss offers commissioning and service at
the coupling through the inspection hole in the system manufacturer’s location. Rate quotes are
bell housings (not available on all bell housings). offered upon request.
If the motor is turning the wrong direction,
switch two phases in the connection box of the
motor or reprogram the direction in VFD.
When the motor is turning in the right direction,

the pump can be mounted.
180R9264 / IOM APP Pumps - v03 / 11.2013 13

6. Operation of pump
unit
6.1 General safety information G) Drop in flow and/or pressure – may indicate
Before inspecting the pump unit, read the Safety wear on one or more parts inside the
chapter 2 in this user manual. pump. The pump must be stopped
immediately and inspected before it is
restarted. Contact the maintenance
6.2 What to listen and look for department.
If one or more of the following examples are
observed, please act as indicated: H) Other observations or troubles, please see
appendix 7, Right and Wrong or appendix
A) Loose bolts – check all bolts and, if 6, the Trouble shooting guide.
necessary, contact the maintenance Both appendices give good advises
department in order to have all bolts regarding design, installation, wiring and
tightened to the specified torque(s). troubleshooting.
See also service and warranty section in
B) Leakage – if a small leakage from the bell appendix 1, Data sheet and appendix 2,
housing is observed. Contact the mainte- Instruction.
nance department.
If the pump is not stopped for inspection as
C) Leakage – if there is a large leak, the unit recommended, it can lead to damage of the
should be stopped immediately. Contact pump or break-down. See also service and
the maintenance department. warranty section in the appendix 1, Data sheet,
in appendix 2, Instruction or appendix 4,
D) High frequency tones – safety/relief valves Instruction for recommended service intervals.
are either damaged or running very close
to their design pressure, stop the unit Danfoss offers service of the pump at the system
immediately. Contact the maintenance manufacturer’s location as well as we offer
department. training in how to service the pump. Quotes are
offered upon request.
E) Increased noise or vibration – requires the
unit to be stopped immediately. Contact Danfoss recommends simultaneously to check
the maintenance department. the filter and membrane condition and to
evaluate contamination; filter and membrane
F) Very high temperatures – may indicate that elements must be replaced if necessary.
one or more parts are damaged inside the
pump. The pump must be stopped
immediately and inspected before it is
restarted. Contact the maintenance
department.
7. Maintenance and
service of the pump
unit 7.1 General safety information Danfoss offers service of the pump at the system
Before servicing the pump unit, it is necessary to manufacturer’s location and training in how to
read and understand this user manual, especially service the pump. Quotes are offered upon
the Safety, chapter 2. Remember to wear suitable request.
safety equipment according to Safety, chapter 2.
7.3 Shut down of the system

7.2 Service and inspection interval for the A) Open the pressure valves at the brine site
pump to release the pressure.
Maintenance and service intervals are depending
on the cleanliness level of the water, hydraulic B) Stop the high-pressure pump.
load and temperature of the pump unit. The
most important parameter is the filtration of the C) Stop the feed pump.
water.
D) Switch off the safety circuit breaker for
See the section Service and warranty in the both the high-pressure pump, feed pump
appendix 1, Data sheet, in appendix 2, Instruc- and VFD and lock them. Only personnel
tion and appendix 4, Instruction for recom- servicing the pump unit should be able to
mended service intervals. unlock/activate the switch again.
For spare parts and service tools, please see E) Open bleeding and drain plugs. Wait until
appendix 3, Parts list. the pump and system are emptied for
water.
14 180R9264 / IOM APP Pumps - v03 / 11.2013

F) Slowly unscrew and remove the bolts and

gaskets from the inlet/outlet hoses or
pipes, be careful about jets of water.
Beware that the system can be pressurized!
G) Attach the lifting equipment to the pump

unit. For instructions on lifting the
complete pump unit, see chapter 4, Arrival
inspection, transportation, handling, lifting
and storage.
H) For the small pumps, unscrew the bolts Returns without a return number will be
holding the pump to the bell housing. For rejected !!!
the bigger pumps, unscrew the bolts/nuts
from the pump and bell housing to the
motor. Afterwards unscrew the bolts/nuts 7.5 Assembling the pump unit
holding the pump and bell housing. Assemble the pump according to the Dis
assembling and Assembling Instruction
I) Carefully pull the pump out of the bell (available at www.ro-solutions.danfoss.com).
housing by using lifting equipment, if
necessary.
7.6 Procedure for mounting the pump onto
J) Hold the pump in different positions above the electric motor
a drip tray; this should allow most of the
water trapped in the pump to drain. Clean
and dry the pump surface and plug the
bleeding and draining plugs.
Mount the flexible coupling and bell housing
K) Move the pump to a clean and safe location according to appendix 2, Instruction.
where the pump can be inspected/
serviced.
7.7 Getting the pump unit back into
operation
7.4 Disassembling and assembling the Find instructions of how to put the pump unit
pump unit back into operation in chapter 4, Arrival inspec-
A) Remove all connections from the pump. tion, transportation, handling, lifting and storage
and Installation and commissioning, chapter 5.
B) Disassemble the pump according to the
Disassembling and Assembling Instruction
(available at www.ro-solutions.danfoss.com) 7.8 Storage of the pump
If the pump has to be shut down for a longer
Clean all parts and surfaces with a fluid period, instructions can be found in appendix 2,
compatible with the materials found in the Instruction.
pump. Wipe the parts clean and dry with a
lint-free clothing.
C) Inspect all parts including shaft seal and if

necessary, replace them; see appendix 3,
Parts list.
D) If the pump is going to be returned to

Danfoss for repair or a warranty claim, it is
important to contact Danfoss in order to
receive a return number and a form to fill
out with product information. A copy of the
form together with contact information
and reason for returning should be sent to
the email address on the form. The same
documents should be attached to the
shipment.
180R9264 / IOM APP Pumps - v03 / 11.2013 15

8. Troubleshooting and
scrapping criteria
8.1 General safety information If water is leaking into the electric motor; it can
Before inspecting the pump unit, it is necessary cause electric shock, fire, short circuit or even
to read and understand this user manual, death. When mounting the pump vertically
especially the Safety chapter 2. always mount the motor above the pump to
avoid water leaking into the electric motor.
Remember to wear suitable safety equipment
according to Safety chapter 2.
Electrical
hazard
8.2 Operational conditions which can cause 8.4 Electrical failure
pump failures If the wiring of the electric motor is incorrect or
The following conditions can cause a pump the ground connection is missing, it can cause
failure : electric shock, burn damages, fire or even death.
• The pump is running dry. If a VFD is used and wrongly programmed, it can
• The inlet pressure is too high. damage the pump and lead to high tempera-
• The inlet pressure is too low. tures or other dangers.
• The temperature of the fluid is too high.
• The ambient temperature is too high. All electrical installation must be carried out by
• The pump is running against a blocked authorized personnel in accordance with
port/closed manual valve. EN60204-1 and/or local regulations.
• The pump is operating at a pressure out of
specification.
• The pump is running with a non-specified/ 8.5 Responsibility
approved fluid. Danfoss takes no responsibility for any abnormal
• The pump is running in the wrong injuries, risks or damages that could arise caused
direction. by abnormal conditions, vibrations, corrosion,
• The filtration is insufficient. abrasives, foreign objects or excessive tempera-
• The pump is not being serviced according tures and shall not be liable for any consequen-
to Danfoss specifications (end of life). tial or incidental damages.
• There is excessive mechanical load on the
shaft coupling and piping.
8.6 Scrapping criteria
Whether the pump can be repaired or need to be
scrapped, depends on in which conditions the
internal parts are, or how damaged the whole
8.3 Mechanical failure unit is. Please use appendix 6, Trouble shooting
If the pump is running dry, the temperature will guide as guideline or send the pump to Danfoss
quickly increase which can cause burns. headquarter in Denmark for evaluation.
If there is any leakage at start-up or during For other observations or troubles, please see
operation, a high pressure jet can cause eye or appendix 7, Right and Wrong which gives good
skin damage. advises regarding design, installation, wiring and
troubleshooting.
Leakage can result in flooding, which can cause
slipping, tripping or falling. In case the pump needs to be scrapped, please
follow your local environmental rules.
16 180R9264 / IOM APP Pumps - v03 / 11.2013

180R9264 / IOM APP Pumps - v03 / 11.2013 17

Subject index
A G S
Address . . . . . . . . . . . . . . . . . . . .7, 8, 15 General information . . . . . . . . . . . . . . . 7 Safety . . . . . . . . . . . 6, 7, 8, 9, 12, 13, 14, 16
Air bubbles . . . . . . . . . . . . . . . . . . . . . 9 Guideline . . . . . . . . . . . . . . . . . . . . . 16 Safety valve . . . . . . . . . . . . . . . . . . . . 7
Appendix . . . . . . . . 7, 8, 9, 10, 11, 14, 15, 16 Scrapping criteria . . . . . . . . . . . . . . . . 16
Application range . . . . . . . . . . . . . . . . . 8 H Serial number . . . . . . . . . . . . . . . . . . . 4
Approval . . . . . . . . . . . . . . . . . . . . . . 6 Handling . . . . . . . . . . . . . . . . . 7, 9, 12, 15 Servicing . . . . . . . . . . . . . . . . . . . 6, 8, 14
Arrival . . . . . . . . . . . . . . . . . . . . 9, 12, 15 Shut down . . . . . . . . . . . . . . . . . . . 14, 15
Assembling . . . . . . . . . . . . . . . . . . 12, 15 I Space requirement . . . . . . . . . . . . . . . . 8
Inspection . . . . . . . . . . . . . . . . . . . 13, 14 Spare part . . . . . . . . . . . . . . . . . . . . . 14
B Installation . . . . . . . 6, 7, 8, 11, 12, 14, 15, 16 Start up . . . . . . . . . . . . . . . . . . . . . . . 8
Bleed . . . . . . . . . . . . . . . . . . . 8, 9, 13, 15 Instruction . . . . . . . . 6, 7, 8, 9, 10, 12, 14, 15 Storage . . . . . . . . . . . . . . . . . 9, 10, 12, 15
Instrumentation . . . . . . . . . . . . . . . . 6, 12 Symbols . . . . . . . . . . . . . . . . . . . . . . . 6
C Introduction . . . . . . . . . . . . . . . . . . . . 6 System . . . . . . . . . . . 6, 7, 8, 9, 11, 12, 13, 14
Checklist . . . . . . . . . . . . . . . . . . . . . . 11 Systems . . . . . . . . . . . . . . . . . . . . . . 7, 8
Check points . . . . . . . . . . . . . . . . . . . 12 M
Chemicals . . . . . . . . . . . . . . . . . . . . . . 9 Maintenance . . . . . . . . . . . . 6, 7, 10, 13, 14 T
Cleanliness . . . . . . . . . . . . . . . . . . 11, 14 Mechanical failure . . . . . . . . . . . . . . . . 16 Table of Contents . . . . . . . . . . . . . . . . . 2
Commissioning . . . . . . 6, 8, 11, 12, 13, 15, 16 Mounting . . . . . . . . . . . . . . . .8, 11, 13, 15 Technical data . . . . . . . . . . . . . . . . . . . 8
Connections . . . . . . . . . . 7, 9, 10, 11, 12, 15 Temperature . . . . . . . 7, 10, 11, 12, 13, 14, 16
Coupling . . . . . . . . . . . . . . 8, 12, 13, 15, 16 N Transportation . . . . . . . . . . . . . 6, 9, 12, 15
Name plate . . . . . . . . . . . . . . . 9, 11, 12, 13 Trouble shooting . . . . . . . . . . . . . . 14, 16
D Noise . . . . . . . . . . . . . . . . . . . . . . . 8, 14
Danger . . . . . . . . . . . . . . . . . . 6, 7, 13, 16 V
Data sheet . . . . . . . . . . 7, 8, 9, 10, 11, 12, 14 L Valve . . . . . . . . . . . . . . 7, 11, 12, 13, 14, 16
Declaration of Conformity . . . . . . . . . .5, 7 Leaking . . . . . . . . . . . . . . . . . . . . . . . 16
Design . . . . . . . . . . 7, 8, 9, 11, 12, 13, 14, 16 Lifting . . . . . . . . . . . . . . . . 6, 9, 10, 12, 15 W
Distributor . . . . . . . . . . . . . . . . . 6, 7, 8, 9 Local regulations . . . . . . . . 6, 7, 8, 11, 12, 16 Warning . . . . . . . . . . . . . . . . . . . . . .6, 9
Dimensions . . . . . . . . . . . . . . . . . . . 8, 11
Disassembling . . . . . . . . . . . . . . . . . . 15 O
Operation . . . . . . . . . 6, 7, 8, 9, 13, 14, 15, 16
E Operational conditions . . . . . . . . . . . 7, 16
EC Declaration of Conformity . . . . . . . .5, 7
Electric motor . . 6, 7, 8, 9, 10, 11, 12, 13, 15, 16 P
Electrical failure . . . . . . . . . . . . . . . . . 16 Piping . . . . . . . . . . . . . . . . . . 9, 11, 12, 16
Electrical hazard . . . . . . . . . . . . . . . . 6, 7 Positioning . . . . . . . . . . . . . . . . . . . . 12
Electrics . . . . . . . . . . . . . . . . . . . . . . 12 Preferred system design . . . . . . . . . . 7, 11
Pre mounting . . . . . . . . . . . . . . . . . . . 11
F Protection . . . . . . . . . . . . . . . . 6, 7, 8, 10
Failure . . . . . . . . . . . . . . . . . . . . . . 8, 16
Filter condition . . . . . . . . . . . . . . . . . . 13 R
Filtration . . . . . . . . . . . . . . . . 9, 12, 14, 16 Relief valve . . . . . . . . . . . . . . . . 12, 13, 14
Flow . . . . . . . . . . . . . . . . . . . 7, 9, 13, 14 Responsibility . . . . . . . . . . . . . . 6, 7, 8, 16
Fluid . . . . . . . . . . . . . . . . . . 11, 12, 15, 16 Return . . . . . . . . . . . . . . . . . . . . . 10, 15
Flush . . . . . . . . . . . . . . . . . . . . . 8, 11, 13 Rotation . . . . . . . . . . . . . . . . . . . . . 8, 13
Danfoss A/S
High Pressure Pumps
DK-6430 Nordborg
Denmark
Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice.
This also applies to products already on order provided that such alterations can be made without subsequential changes being necessary in specifications already agreed.
All trademarks in this material are property of the respective companies. Danfoss and the Danfoss logotype are trademarks of Danfoss A/S. All rights reserved.
18 180R9264 / IOM APP Pumps - v03 / 11.2013

Front page for Appendices
User manual
Appendices for Installation,

Operation and Maintenance Manual
APP pumps (APP 11-13)
APP 11-13
User manual Appendices for IOM Manual for APP Pumps (APP 11-13)
Table of Contents 1. Data sheet for APP 11-13 pumps(521B1215) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

2. APP pump instruction APP 11-13 (180R9223) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3. IOM Electric motors (180R9230) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
4. Recommended service intervals for APP pumps (180R9199) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
5. APP parts list (521B0941) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
6. Trouble shooting guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
7. Right and wrong (180R9042) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
2 180R9264 / IOM APP 11-13 Appendices - v04 / 11.2013

1. Data sheet for APP

11-13 pumps(521B1215)
Data sheet
Data sheet
APP 11-13
ro-solutions.com
Data sheet APP 11-13
Data sheet for 1. Introduction

APP 11-13 pumps
(521B1215) 2. Benefits
Table of Contents 3. Technical data
4. Variants
5. Flow at different rpm
6. Flushing valve
7. Power requirements
8. Temperature and corrosion

8.1 Operation
8.2 Storage
9. Noise level
10. Filtration
11. Dimensions
12. Dimensions, complete unit
13. Installation
13.1 Mounting
13.2 Open-ended system with direct water supply
13.3 RO system with APP pump
14. Service
14.1 Warranty
14.2 Maintenance
14.3 Repair
4
2 180R9264 // DKCFN.PD.013.E2.02
521B1215 IOM APP 11-13 Appendices - v04 / 11.2013
/ 02.2013
1. Introduction APP 11-13 pumps are designed to supply low All parts included in the pumps are designed to
viscosity and corrosive fluids under high provide long service life, i.e. long service life with
pressure, eg. in seawater reverse osmosis a constantly high efficiency and minimum
filtration applications and for high pressure salt service required.
water pumping.
The pumps are fixed displacement pumps in
The pumps are based on the positive displace- which the flow is proportional to the number of
ment principle (axial piston design) which revolutions of the input shaft and the pump
enables a very light and compact design, and displacement.
they are designed so that the lubrication of the
moving parts in the pumps is provided by the
fluid itself. No oil lubrication is thus required.
The pumps are supplied with an integrated

flushing valve that allows the salt water to flow
from inlet to the outlet, when the pump is not
running.
1: Shaft Sealing
2: Bolts for bell
housing
3: Flushing valve
4: Port plate
5: Bleeding plug
6: Valve/thrust plate
7: Piston/shoe
8: Cylinder barrel
9: Retainer ring
10: Swash plate
with bearing
11: Port flange
with bearing
12: Drain plug
13: Housing
14: Springs
2. Benefits • O
ne of the smallest and lightest pumps on • No oil lubricant required.
the market. • Integrated flushing valve.
• Can be powered by a combustion engine • All parts of the pump are made of non-corro-
provided that a special coupling is used. sive materials, e.g. Duplex (EN1.4462/UNS
• Long service life / no preventive maintenance S31803-S32205) and Super Duplex (EN1.4410/
required in the warranty period. UNS S32750) stainless steel and carbon
• Generates insignificant pulsations in the reinforced PEEK.
pressure line. • High efficiency.
180R9264 // DKCFN.PD.013.E2.02
/ 02.2013 5
3
3. Technical data APP Pumps APP 11 / 1200 APP 11 / 1500 APP 13 / 1200 APP 13 / 1500
Code number 180B3212 180B3211 180B3214 180B3213
Geometric displacement cm³/rpm 166 137 197 166
in³/rpm 10.1 8.4 12.0 10.1
Rated flow at max. speed 1) m³/h 11.0 11.1 13.1 13.5
gpm 48.4 49 57.7 59.3
Outlet min. pressure 2) bar 30 30 30 30
psi 435 435 435 435
Outlet max. pressure, cont. 3) bar 80 70 80 70
psi 1160 1015 1160 1015
Inlet min. pressure bar 2 2 2 2
psi 29 29 29 29
Inlet max. pressure, cont. bar 5 5 5 5
psi 72.5 72.5 72.5 72.5
Inlet max. pressure, peak bar 10 10 10 10
psi 145 145 145 145
Max. speed cont. rpm 1200 1500 1200 1500
Min. speed cont. rpm 700 700 700 700
Power requirement at kW 23 24 27 29
max. speed and 60 bar
hp 30.8 32.2 36.2 38.9
outlet pressure
Torque at 60 bar Nm 179 148 212 179
outlet pressure
lbf-ft 132 109 157 132
Weight Kg 75 75 75 75
lb 165 165 165 165
Integrated flushing valve YES YES YES YES
1) Typical average flow at 60 bar (870 psi)

2) For lower pressure, please contact Danfoss RO Sales Organization
3) For higher pressure, please contact Danfoss RO Sales Organization
The pumps are designed according to EN809.
4. Variants • A
vailable as ATEX certified. Category 2, zone 1 For more details on the variants, please contact
and category 3, zone 2. the Danfoss RO Solutions Sales Organisation.
• Available with material certificates on wetted
parts.
6
4 180R9264 // DKCFN.PD.013.E2.02
/ 02.2013
5. Flow at different rpm When using the diagrams shown below, it is easy best if the flow required and the rotation speed
to select the pump which fits the application (rpm) of the pump are known.
APP 1200 rpm version

15,00
14,00
13,00 APP 13
12,00
11,00 APP 11
m3/h 10,00
9,00
8,00
7,00
6,00
5,00
700 800 900 1000 1100 1200
rpm

15,00
14,00 APP 13
13,00
12,00
11,00 APP 11
m3/h
10,00
9,00
8,00
7,00
6,00
5,00
700 800 900 1000 1100 1200 1300 1400 1500
rpm
Furthermore, these diagrams shows that the flow the “required “ flow can be obtained by chang-
can be changed by changing the rotation speed ing the rotation speed to a corresponding value.
of the pump. The flow/rpm ratio is constant, and Thus, the required rpm can be determined as:
Required flow × Rated rpm

Required rpm =
Rated flow
180R9264 // DKCFN.PD.013.E2.02
/ 02.2013 7
5
6. Flushing valve
Flushing Valve characteristic
2,00
1,80
1,60
Pressure drop [bar]

1,40
1,20
1,00
0,80
0,60
0,40
0,20
0,00
0 20 40 60 80 100 120 140 160
Flow [l/min]
7. Power requirements Pump Flow Pressure rpm Cal.

model Factor
60 bar 70 bar 80 bar
l/min m³/h gpm 870 psi 1015 psi 1160 psi
APP 11 / 184 11,0 48,5 23 kW 27 kW 31 kW 1180 477
1200
APP 11 / 190 11,4 50,1 24 kW 28 kW 32 kW 1480 475
1500
APP 13 / 218 13,1 57,6 27 kW 32 kW 36 kW 1180 482
1200
APP 13 / 230 13,8 60,7 29 kW 34 kW 38 kW 1480 478
1500
The power requirements can be determined using one of the following guiding equations:
3
l/min x bar 16.7 x m /h x bar 0.26 x gpm x psi
Required power= Calc. factor [kW] or Calc. factor [kW] or Calc. factor [kW]
1 hp = 0.75 kW 1 l/min = 0.26 gpm

1 kW = 1.34 hp 1 m3/h = 4.40 gpm
1 gpm = 3.79 l/min 1 gpm = 0.23 m3/h
8
6 180R9264 // DKCFN.PD.013.E2.02
/ 02.2013
8. Temperature and 8.1 Operation 8.2 Storage

corrosion
Fluid temperature: Storage temperature:
+2 °C to +50 °C (+35.6 °F to 122 °F) - dependent -40 °C to +70 °C (-40 °F to 158 °F) – provided
on the NaCl concentration that the pump is drained of fluid and stored
”plugged”.
Ambient temperature:
+2 °C to +50 °C (+35.6 °F to 122 °F) Frost protection is required at temperatures
below 2°C. Danfoss recommends using
The chart on the next page illustrates the DOWFROST from DOW Chemical Company or
corrosive resistance of different types of stainless Chilsafe mono propylene glycol from Arco
steel related to NaCl concentration and tempera- Chemical Company.
ture.
All critical parts of the APP water pump is made

of Super Duplex.
If the water pump is operated at high salinity,

always flush the water pump with fresh water at
operation stop in order to minimize the risk of
crevice corrosion.
NaCI vs. temperature
80 º C Duplex
70
Super Duplex
60
50
316L
40
30
20 -
100 1000 10 000 100 000 CI
ppm
160 1600 16000 160000 NaCI
ppm
9. Noise level The sound pressure levels, L PA, 1 m*) db(A) for The noise level is influenced by:
APP 11-13 pumps are typically 81 dB(A) at • The speed of the pump, high rpm create more
60 bar/1500rpm and 85 dB at 80 bar/1500rpm. noise than low rpm
• R igid mounting of the pump generates more
Generally, noise will be reduced if speed is noise than flexible mounting
reduced and vice versa. Use flexible hoses in • P ipe mounting direct to the pump increases
order to minimize vibrations and noise. the noise level compared to a flexible hose
• If using a VFD the motors can produce higher
Since the pump is typically mounted on a bell noise values depending on the operation
housing or frame, the noise level must be point.
determined for the complete unit (system).
It is therefore very important that the motor/

pump unit is mounted correctly on a frame with *)
1 meter from the pump unit surfaces
antivibration isolation to minimize vibrations and (reference box) acc. to EN ISO 20361 section 6.2.
noise. Deviation σTOT = ± 1,6 dB(A)
180R9264 // DKCFN.PD.013.E2.02
/ 02.2013 9
7
10. Filtration As water has very low viscosity, the APP pumps cartridges typically have only 50% filtration
have been designed with very narrow clearance efficiency. This means that for each 100,000 parti-
in order to control internal leakage rates and cles reaching the filter, 50,000 particles pass
improve component performance. Therefore it is through it compared to only 20 particles in a
important that the inlet water is filtered properly filter with an efficiency of 99.98%.
to minimize the wear of the pump.
For more information on the importance of
The main filter must have a filtration efficiency of proper filtration, please consult our publication
99.98% at 10 µm. We recommend to use “Filtration” (code number 521B1009), which also
precision depth filter cartridges rated 10µm abs. will provide you with an explanation of filtration
ß10>5000 (equivalent to a filtration efficiency of definitions and a guidance on how to select the
99.98%). Bag filters and string wound filter right filter.
11. Dimensions
Inlet
Outlet
10
8 180R9264 // DKCFN.PD.013.E2.02
/ 02.2013
Description APP11 - APP13 Accessories Type Code no.

2” inlet hose kit 2” Victaulic 180Z0298
2 m / 79”
Parallel key, mm 10 × 8 × 45
DIN 6885 2” inlet Vic. 2” Victaulic 180Z0166
inch 0.39 × 0.31 × 1.77 Super Duplex
Bleeding G ¼”, Hexagon AF = 6 mm Non-return 1,5” Victaulic 180H0053
Inlet port M42 x 1.5; depth 17 mm valve (outlet) (OD 48,3 mm)
Super Duplex
Outlet port M42 x 1.5; depth 17 mm
Pump mounting 125 B 4 For more details on the accessories, please
flange contact the Danfoss RO Solutions Sales
Organisation.
12. Dimensions,
complete unit
180R9264 // DKCFN.PD.013.E2.02
/ 02.2013 11
9
Pump A B C D E F G IEC Electric motor

(mm) (mm) (mm) (mm) (mm) (mm) (mm)
APP 11 350 473 180 279 241 578 204 22 kW, IEC 180L-4
APP 11 400 513 200 318 305 659 204 30 kW, IEC 200L-4
APP 13 450 561 225 356 286 667 234 37 kW, IEC 225S-4
Note: Examples of different pump/motor sizes motors and couplings. Please always check
and drawing dimensions are only for IEC required motor power and dimensions.
13. Installation 13.1 Mounting To ensure easy mounting of the flexible coupling
The figure below illustrates how to mount the without using tools, the tolerances must be
pump and connect it to the electric motor/ dimensioned accordingly.
combustion engine.
Note: Any axial and radial loads on the pump
If alternative mounting is required, please shaft must be avoided.
contact Danfoss RO Sales Organization for
further information.
Ensure 3-5mm (0.12-0.2in) air gap

between coupling parts
A B C
A: Flexible coupling
B: Bell housing
C: Motor shaft
13.2 Open-ended system with direct water

supply
In order to eliminate the risk of cavitation, a
positive inlet pressure is always to be main-
tained. Please see technical data (section 3) for
specific pressure values.
1. Place the filter (1) in the water supply line in

front of the pump.
2. Place a monitoring pressure switch (2) - set at

min. inlet pressure - between filter and pump
inlet. The monitoring switch must stop the
pump at pressures lower than min. inlet
pressure. Please see technical data (section 3)
for specific pressure values.
3. Install a low pressure safety valve or a Note: If a non-return valve is mounted in the
pressure relief valve (3) in order to avoid inlet line, a low pressure relief valve is also
system or pump damage in case the pump required between non return valve and pump
stops momentarily or is spinning backwards. as protection against high pressure peaks.
12
10 180R9264 // DKCFN.PD.013.E2.02
/ 02.2013
13.3 RO system with APP pump 6. For easy system bleeding and flushing, a
1. Dimension the inlet line to obtain minimum bypass non-return vavle (6) is integrated in
pressure loss (large flow, minimum pipe the APP pump.
length, minimum number of bends/connec- 7. A non-return valve (7) in outlet can be
tions, and fittings with small pressure losses). installed in order to avoid backspin of the
2. Place an inlet filter (1) in front of the APP pump. The volume of water in the membrane
pump (2). Please consult section 10, “Filtra- vessel works as an accumulator and will send
tion” for guidance on how to select the right flow backwards in case of the pump stops
filter. Thoroughly clean pipes and flush momentarily.
system prior to start-up. 8. A safety valve or a pressure relief valve (8) can
3. Place a monitoring pressure switch (3) set at be installed in order to avoid system damage
min. inlet pressure between filter and pump as the Danfoss APP pump creates pressure
inlet. The monitoring switch must stop the and flow immediately after start-up, regard-
pump at pressures lower than minimum less of any counter-pressure.
pressure.
4. Use flexible hoses (4) to minimize vibrations
and noise. Note: If a non-return valve is mounted in the
5. In order to eliminate the risk of damage and inlet line, a low pressure relief valve is also
cavitation, a positive pressure at the inlet (5) is required between non return valve and pump
always to be maintained at min. inlet pressure as protection against high pressure peaks.
and max. inlet pressure. Recommend to install
safety valve or a pressure relief valve (9) in
order to avoid high pressure peaks in case the
pump stops momentarily or is spinning
backwards.
14. Service 14.1 Warranty breakdown of the pump. If the parts are not
Danfoss APP pumps are designed for long replaced, more frequent inspection is recom-
operation, low maintenance and reduced mended according to our guidelines.
lifecycle costs.
Provided that the pump has been running Pump shutdown:

according to the Danfoss specifications, Danfoss The APP pumps are made of Duplex/Super
guarantees 8,000 hours service-free operation, Duplex materials with excellent corrosion
however, max. 18 months from date of produc- properties. It is, however, always recommended
tion. to flush the pump with freshwater when the
system is shut down.
If Danfoss recommendations concerning
system-design are not followed, it will strongly
influence the life of the APP pumps. 14.3 Repair
In case of irregular function of the APP, please
contact the Danfoss RO Solutions Sales
14.2 Maintenance Organisation.
After 8,000 hours of operation it is strongly
recommended to inspect the pump and
change any worn parts, e.g. pistons and shaft
seal. This is done in order to prevent a potential
180R9264 // DKCFN.PD.013.E2.02
/ 02.2013 13
11
Data sheet Water pumps APP 11-13
Danfoss A/S
High Pressure Pumps
DK-6430 Nordborg
Denmark
14
12 180R9264 // DKCFN.PD.013.E2.02
/ 02.2013
2. APP pump instruction

APP 11-13 (180R9223)
Instruction
APP pump instruction

APP 11-13 and APP 16-22
www.ro-solutions.com
Instruction APP pump instruction APP 11-13 and APP 16-22
APP pump instruction 1. Identification

APP 11-13 and APP 16-22
(180R9223) 2. System design
2.1 Open-ended systems with direct water supply
Table of Contents 2.2 Preferred RO system design and P&ID
2.3 Reversible pumps
2.4 General comments on
3. Building up the pump unit

3.1 Mounting
3.2 Direction of rotation
3.3 Orientation
3.4 Protection against too high outlet pressure
3.5 Connections
4. Initial start-up
5. Operation
5.1 Temperature
5.2 Pressure
5.3 Dry running
5.4 Disconnection
5.5 Storage
5.5.1 Recommended procedure
6. Service
6.1 Warranty
6.2 Maintenance
6.3 Repair
7. EC Declaration of Conformity
1. Identification NESSIE © Pump

Type APP
Serial no.
Code no.
MADE IN DENMARK
16
2 180R9264 / 521B1184
180R9223 IOM APP 11-13 Appendices - v04/ /12.2012
/ DKCFN.PI.013.T1.02 11.2013
2. System design The design of the system must ensure that 2. Place a monitoring pressure switch (3)
self-emptying of the pump during standstill is between filter and pump inlet - set at min.
avoided. 2 bar (29 psi) inlet pressure. The monitoring
The inlet pressure of the pump must never pressure switch must stop the pump at
exceed the outlet pressure. This may typically pressures lower than 2 bar (29 psi ) inlet
occur in boosted or open-ended systems with pressure.
direct water supply. 3. Install a low pressure safety valve or a low
pressure relief valve (4) in order to avoid
system or pump damage in case the pump
2.1 Open-ended systems with direct stops momentarily ( high pressure peaks )
water supply or starts spinning backwards.
The pump is supplied with water direct from a
feed pump.
In order to eliminate the risk of cavitation, a Note: If a non return valve (2) is mounted in the
positive inlet pressure of at least 2 bar(29 psi) is inlet line, a low pressure relief valve is also
always to be maintained, but it must not exceed required between non return valve and pump
5 bar (72.5 psi) continuously. as protection against high pressure peaks.
1. Place the filter (1) in the water supply line in

front of the pump.
1
2
3
PS
Inlet
Outlet
180R9264 / 521B1184
/ DKCFN.PI.013.T1.02 11.2013 17
3
2.2 Preferred RO system design and P&ID

1. Dimension the inlet line to obtain mini- pressure relief valve (9) in order to avoid
mum pressure loss (large flow, minimum high pressure peaks in case the pump stops
pipe length, minimum number of bends/ momentarily or starts spinning backwards.
connections, and fittings with small
pressure losses). 6. For easy system bleeding and flushing, a
bypass non-return vavle (6) is integrated in
2. Place an inlet filter (1) in front of the APP the APP pump.
pump (2). Please consult the Danfoss filter
data sheet for guidance (521B1009) on how 7. A non-return valve (7) in outlet can be
to select the right filter. Thoroughly clean installed in order to avoid backspin of the
pipes and flush system prior to start-up. pump. The volume of water in the mem-
brane vessel works as an accumulator and
3. Place a monitoring pressure switch (3) set will send flow backwards in case of the
at min. inlet pressure between filter and pump stops momentarily.
pump inlet. The monitoring switch must
stop the pump at pressures lower than 8. A safety valve or a pressure relief valve (8)
minimum pressure. can be installed in order to avoid system
damage as the Danfoss APP pump creates
4. Use flexible hoses (4) to minimize vibrations pressure and flow immediately after
and noise. start-up, regardless of any counter
pressure.
5. In order to eliminate the risk of damage
and cavitation, a positive pressure at the Note: If a non return valve is mounted in the
inlet (5) is always to be maintained at min. inlet line, a low pressure relief valve is also
inlet pressure and max. inlet pressure. required between non return valve and pump
Recommend to install safety valve or a as protection against high pressure peaks.
2.3 Reversible pumps 2.4 General comments on

If exposed to high pressure in the outlet while the
electric motor is not energized, the pump will Filtration
start spinning backwards. This will not harm the A good filtration is vital to ensure a long and
pump as long as the pressure in the inlet does not trouble free life of the pump.
exceed the max. pressure peak of 10 bar (145 psi).
As water has very low viscosity, the APP pumps
If a non-return valve is mounted in the inlet line, have been designed with very narrow clearance
a low-pressure relief valve is also required as in order to control internal leakage rates and
protection against high-pressure pulses and high improve component performance. Therefore it is
pressure in general. important that the inlet water is filtered properly
to minimize the wear of the pump.
Alternatively a high-pressure check valve can be
mounted in the pump discharge line to prevent The main filter must have a filtration efficiency of
the pump from reversing. 99.98% at 10 µm. We recommend to use
precision depth filter cartridges rated 10µm abs.
The dotted setup ensures that the inlet pressure ß10>5000 (equivalent to a filtration efficiency of
does not exceed 10 bar (145 psi), when a 99.98%). Bag filters and string wound filter
non-return valve is mounted in the inlet. cartridges typically have only 50% filtration
efficiency. This means that for each 100,000
Attention: In order to avoid the risk of cavita- particles reaching the filter, 50,000 particles pass
tion, the inlet pressure at the pump must be through it compared to only 20 particles in a
min. 2 bar (29 psi). filter with an efficiency of 99.98%.
The inlet line connection must be properly
tightened, as possible entrance of air will cause
cavitation.
18
4 180R9264 / 521B1184
/ DKCFN.PI.013.T1.02 11.2013
For more information on the importance of Monitoring

proper filtration, please consult our data sheet It is recommended to continuously monitor the
“Filtration” (521B1009), which also will provide following conditions:
you with an explanation of filtration definitions • filter clogging
and a guidance on how to select the right filter. • pressure (inlet- and outlet side of the pump)
3. Building up the 3.1 Mounting

pump unit
A: Elastic coupling
B: Bell housing
C: Motor shaft
D: Pump flange
1: Bolts and nuts: torque 75 Nm ±5 Nm

2: Bolts and nuts: torque 40 Nm ±4 Nm
3: Torque see table below
1
3
2
C
1
Thread M4 M5 M6 M8 M10 M12 M16

size
Torque 1,5 2 4,8 10 17 40 80
(Nm)
1. Mount the coupling flush or maximum 6. Adjust respectively, verify the measure-
1 mm offset from the pump shaft end. ment, and secure both couplings with the
Ensure an air gap between coupling and right torques on the locking screws (see
pump flange of min. 4 mm (0.16 inch). coupling operation & mounting instruc-
2. Mount the bell housing on pump. Secure tion).
nuts with the right torque. 7. Mount the elastic gear ring and mount the
3. Measure the longest distance “A” from top bell housing/pump on the motor. After
of bell housing to the button of coupling mounting it must be possible to move the
claw. elastic gear ring 3-5 mm (0.12 - 0.2 inch)
4. Mount the coupling on motor shaft. Ensure axial “C”. The check can be done through
the coupling and motor flange are not in the inspection hole of bell housing. Secure
contact with each other. flange bolts with the right torque.
5. Measure from motor flange to the top of
the coupling. That measurement “B” shall
be 3-5 mm (0.12 - 0.2 inch) shorter than the
measurement “A”.
180R9264 / 521B1184
/ DKCFN.PI.013.T1.02 11.2013 19
5
If alternative mounting is desired, please contact

the Danfoss RO Solutions Sales Organisation.
Choose proper tolerances to ensure an easy

mounting of the elastic coupling without use of
tools.
Please take care to observe the recommended

length tolerances of the chosen coupling, as an
axial force on the pump will damage the pump.
3.2 Direction of rotation

Is indicated by means of an arrow on the pump
label.
NESSIE © Pump
Type APP
Serial no.
Code no.
MADE IN DENMARK
3.3 Orientation
The pump can be mounted/orientated in any
horizontal direction with the inlet and the outlet
pointing upwards, downwards or to either side.
CC C
C
C - Bleeding
C
C
CC
20
6 180R9264 / 521B1184
/ DKCFN.PI.013.T1.02 11.2013
3.4 Protection against too high Both the inlet and outlet lines must be flexible
outlet pressure soft hoses.
The pump should be protected against too high
outlet pressure by means of a safety valve or a The valve outlet must not be connected
pressure relief valve. The valve should be placed directly to the pump suction line. It must be
as close to the pump as possible. The opening connected directly to the drain.
characteristics of the valve must not result in
peak pressures higher than 80 bar (1,160 psi).
Inlet
Inlet
Outlet
Outlet
3.5 Connections
I : Inlet C
O : Outlet
C : Bleeding I
D : Parallel key
180R9264 / 521B1184
/ DKCFN.PI.013.T1.02 11.2013 21
7
APP 11 - APP 13
Description APP 11 - APP 13 Accessories Type Code no.

2” inlet hose kit 2” Victaulic 180Z0298
2 m / 79”
inch 0.39 × 0.31 × 1.77 Super Duplex
Bleeding G ¼”, Hexagon AF = 6 mm Non-return 1,5” Victaulic 180H0053
valve (outlet) (OD 48,3 mm)
Inlet port M42 x 1.5; depth 17 mm Super Duplex
For more details on the accessories, please
Pump mounting 125 B 4
Organisation.
APP 16 – APP 22
Description APP 16 – APP 22 Accessories Type Code no.

2” inlet hose 2” Victaulic 180Z0298
kit 2 m/79”
In 0.47 × 0.31 × 2.76 Super Duplex
Bleeding G ¼”, Hexagon AF = 6 mm Non-return 2” Victaulic 180H0256
valve (outlet) (OD 63 mm)
Inlet port M52 x 1.5; depth 21 mm Super Duplex
Pump mounting 125 B 4 For more details on the accessories, please
Organisation.
22
8 180R9264 / 521B1184
/ DKCFN.PI.013.T1.02 11.2013
4. Initial start-up 1. Flush inlet line before connecting the Warning:

pump, to remove possible impurities from Make sure that the direction of rotation of the
pipes, hoses etc. electric motor corresponds to the direction of
2. Connect pump inlet to inlet line and flush rotation of the pump (see label on pump).
the pump for 5 min. by means of the
internal flushing valve, to remove possible Otherwise the pump will be damaged if a
impurities from pipes, hoses etc. check valve is placed between pump and feed
3. Loosen top bleeding plug “C” (see item 3.3) pump.
using an allen key (only plugs with internal
hexagan sockets). Retighten the plug,
when water appears from the bleeding
plug.
4. Make sure that the direction of rotation of
the electric motor corresponds to the
direction of rotation of the pump (see label
on pump).
5. Now the pump is ready for start-up.
180R9264 / 521B1184
/ DKCFN.PI.013.T1.02 11.2013 23
9
5. Operation 5.1 Temperature The chart below illustrates the corrosive

resistance of different types of stainless steel
Fluid temperature: related to NaCl concentration and temperature.
Min. +2° C to max. +50° C
(Min. +35.6° F to max. +122° F) The APP water pump is made of Duplex and
Super Duplex. If the water pump is operated
Ambient temperature: above the Super Duplex line, always flush water
Min. +2°C to max. +50°C pump with fresh water at operation stop in order
(Min. +35.6°F to max. +122°F) to minimise the risk of crevice corrosion.
In case of lower operating temperatures, please

contact the Danfoss RO Solutions Sales Organisa-
tion.
80 º C Duplex
70
Super Duplex
60
50
316L
40
30
20 -
100 1000 10 000 100 000 CI
ppm
160 1600 16000 160000 NaCI
ppm
5.2 Pressure 5.5 Storage

The inlet pressure for APP 11-13 and APP 16-22
must be min. 2 bar (29 psi) and max. 5 bar Storage temperature:
(72,5 psi). Min. -40°C to max. +70°C
At lower pressures the pump will cavitate, (Min. -40°F to max. +158°F)
resulting in damage of the pump.
When preparing the pump for long-term storage
Max. inlet pressure peak (e.g. in case the pump or for temperatures below the freezing point,
stops momentarily) up to 10 bar (145 psi) are flush the pump with an anti-freeze medium type
acceptable. monopropylene glycol to prevent internal
corrosion or frost in the pump.
Max. pressure on the pump’s outlet line should
be limited at 80 bar (1,160 psi) continuously. For further information on anti-freeze media,
NB: The pump unit should include a pressure please contact the Danfoss RO Solutions Sales
gauge on the high pressure side. Organisation.
5.3 Dry running 5.5.1 Recommended procedure

When running, the pump must always be 1. Disconnect the water supply to the pump.
connected to the water supply in order to avoid 2. Through the lower bleeding plug, empty
damage if it should run dry. the pump housing of water and close it
again.
3. Connect the pump to a tank containing
5.4 Disconnection anti-freeze additive. Connect a hose to the
If the inlet line is disconnected from the water inlet port of the pump and via another
supply, the pump will be emptied of water hose return the flow from the outlet port to
through the disconnected inlet line. When the tank with anti-freeze additives.
starting up again, follow the bleeding procedure 4. Quickly start and stop the pump. Make
described under section 4: Initial start up. sure that the pump does not run dry.
The pump is now protected against
internal corrosion and frost.
24
10 180R9264 / 521B1184
/ DKCFN.PI.013.T1.02 11.2013
6. Service 6.1 Warranty of the pump. If the parts are not replaced, more
Danfoss APP pumps are designed for long frequent inspection is recommended according
operation, low maintenance and reduced to our guidelines.
lifecycle costs.
Provided that the pump has been running Stand still

according to the Danfoss specifications, Danfoss The APP pumps are made of Duplex/Super
guarantees 8,000 hours service-free operation, Duplex materials with excellent corrosion
however, max 18 months from date of produc- properties. It is however, always recommended
tion. to flush the pump with freshwater when the
system is shut down.
If Danfoss recommendations concerning
system-design are not followed, it will strongly
influence the life of the APP pumps. 6.3 Repair
In case of irregular function of the APP, please
contact the Danfoss RO Solutions Sales
6.2 Maintenance Organisation.
After 8,000 hours of operation it is strongly
recommended to inspect the pump and change
any worn parts, e.g. pistons and shaft seal. This is
done in order to prevent a potential breakdown
180R9264 / 521B1184
/ DKCFN.PI.013.T1.02 11.2013 25
11
Danfoss A/S
High Pressure Pumps
DK-6430 Nordborg
Denmark
26
14 180R9264 / 521B1184
/ DKCFN.PI.013.T1.02 11.2013
3. IOM Electric motors
(180R9230)
Electric Motors
Motor Manual
hoyermotors.com
Manual
Motor Manual
1. General Correct alignment is essential to avoid bearing, vibration

and shaft failure.
This manual concerns the following types of standard Use appropriate methods for alignment.
induction motors from Hoyer: Re-check the alignment after the final tightening of the
HMA2, HMC2, HMD, HMT, MS, Y2E1, Y2E2, YDT bolts or studs.
These motors are manufactured in accordance with IEC/EN Check that drain holes and plugs face downwards. We
60034-4 and IEC/EN 60072. recommend opening the drain hole for motors placed
Motors are rated for the ambient temperature range -20°C outdoors and not running 24 hours / day, so that the motor
to +40°C and site altitudes ≤1000 m above sea level. can breathe, thus ensuring a dry motor.
Low-voltage motors are components for installation in
machinery. They are CE marked according to the Low
Voltage Directive 2006/95/EC 4. Electrical connection
Work is only permitted to be carried out by qualified
2. Transport and storage specialists and must to be carried out in accordance with
Check the motor for external damage immediately upon local regulations.
receipt and, if found, inform the forwarding agent right Before work commences, ensure that all power is switched
away. Check all rating plate data, and compare it with the off and cannot be switched on again. This also applies to the
requirement of the motor. auxiliary power circuits, e.g. anti-condense heaters.
Turn the shaft by hand to check free rotation, remove Check that supply voltage and frequency are the same as
transport locking if used. rated data.
Transport locking must be used again for internal transport Motors can be used with a supply deviation of ± 5% voltage
also. It is also important that transport locking is used when and ± 2% frequency, according to IEC60034-1
motors are transported mounted on equipment.
All motors should be stored indoors, in dry, vibration- and Connection diagrams for main supply and accessory as PTC
dust-free conditions. or heater are located inside the terminal box.
Lifting eyebolts must be tightened before use. Damaged Connections must be made in such a way as to ensure that
eyebolts must not be used, check before use. Lifting eyes at a permanently safe electrical connection is maintained,
motor must not be used to lift the motor when it is attached both for the main supply and the earth connection.
to other equipment. We recommend that crimped connections are made in
accordance with IEC 60352-2.
Before commissioning, measure the insulation impedance.
If values are ≤ 10MΩ at 25°C, the winding must be oven dried. Tightening torques for terminal board screws:
The insulation resistance reference is halved for each 20°C Thread M5 M6 M8 M10 M12 M16 M20
rise in motor temperature.
T.(Nm) 2.5 3.5 7 12 18 35 55
It is recommended that shafts are rotated periodically by
hand to prevent grease migration.
Ensure that the terminal box is clean and dry.
Unused glands must be closed.
3. Installation Check the terminal box gasket before it is remounted.
The motor must be fixed on a stable, clear and flat founda-
tion. It must be sufficiently rigid to withstand possible short 5. Maintenance
circuit forces.
It is important to ensure that the mounting conditions do Inspect the motor at regular intervals, keep it clean and
not cause resonance with the rotational frequency and the ensure free ventilation air flow, check the condition of
doubled supply frequency. shaft seals and replace if necessary. Both electrical and
Only mount or remove drive components (pulley, coupling, mechanical connections must be checked and tightened if
etc.) using suitable tools, never hit the drive components necessary.
with a hammer as this will cause damage to the bearing.
The motor are balancing with half key, ensure that the drive
components are also the same.
2
28
Hoyer Motors, Motor Manual, October 2011
180R9264 / IOM APP 11-13 Appendices - v04 / 11.2013
Motor Manual
Bearing size and type are specified on the rating plate. The table values are based on an ambient temperature of
Motor types HMA2 and HMC2 is as standard with lifetime 25°C. The values must be halved for every 15K increase in
greased bearing with motor size ≤225. bearing temperature.
Motor types MS and Y2E is as standard with lifetime greased Higher speed operations, e.g. frequency converter drive will
bearing with motor size ≤160. require shorter greasing intervals. Typically, doubling the
speed will reduce the values by 50%.
Typical duty hours for lifetime lubricated bearings.
Frame size Poles Typical lifetime

6. Special note for Atex Zone 22 motors.
56 – 160 2–8 40.000h Notice for the use of electrical equipment in areas with
180 2 35.000h combustible dust.
200 2 27.000h Designation of motor according to EC directive:
Ex II 3D T125°C, IP55.
225 2 23.000h
180 – 225 4–8 40.000h The dust hazardous 3-phase asynchronous motors are
in accordance with European standard EN 50281-1-1.
Motors with a re-greasing system must be lubricated with Combustible dust areas will be found in agricultural areas
high quality lithium complex grease, NLGI grade 2 or 3, with and in industrial environments.
a temperature range of between -40°C to +150°C. Only one electrical installation may be installed in one
specified area (zone).
Motors are normal fitted with a data plate with greasing
information; if it is missing use the following re-greasing Only certificated cable glands for category 2D may be used.
intervals. Unused glands must be closed.
Connections must be made in such a way as to ensure that
Frame Grease 2 pole 4 pole 6 pole 8 pole
a permanently safe electrical connection is maintained,
size (g) (h) (h) (h) (h)
both for the main supply and earth connection.
160 20 4200 7000 8500 8500 Installations must be in accordance with actual standards
180 20 4200 7000 8500 8500 for installation in the Zone 22 area.
200 25 3100 6500 8500 8500
It is recommended that EN 50281-2 is followed according
225 25 3100 6500 8500 8500
temperature and dust on the motor surface.
250 35 2000 6000 7000 7000 The use of motors with so much surface dust that the
280 35 2000 6000 7000 7000 motor temperature increases is not permitted.
315 50 1500 5500 6500 6500 Regularly cleaning is recommended.
The radial shaft sealing ring is part of the ATEX certification.
355 60 1000 4000 5000 6000
It is important that the ring is always intact.
400 80 800 3000 4000 6000 The shaft sealing must be regularly checked, and if dry
it must be lubricated. It is recommended that the seal is
Grease the motor while running, open the grease outlet plug re-lubricated regularly.
and let the motor run 1-2 hours before the outlet grease Always use the original seal ring when replaced.
plug is closed again. Replacing bearings also means replacing the seals.
Grease the motor for the first time during commissioning. All machines must be inspected regularly for mechanical
damage.
The following applies in general for both lifetime lubricated The user is responsible for changing parts in accordance
and re-lubricated bearings: with the lifetime of parts, in particular:
At 60Hz the time will be reduced by app. 20%. bearings, grease and lubrication of shaft sealing.
Data for vertically mounted motors are half of the above
values. Maintenance, repairs and replacement on zone 22 motors
must only be carried out by qualified specialists.

Hoyer Motors, Motor Manual, October 2011 3
29
IOM electromotor - Hoyermotors
Motor Manual
Correct alignment
alignment is is essential
essential to
to avoid
avoid bearing,
bearing, vibration
vibration
1. General Correct
and shaft
shaft failure.
failure.
and
This manual
This manual concerns
concerns thethe following
following types
types of
of standard
standard Use appropriate
appropriate methods
methods forfor alignment.
alignment.
Use
induction motors
induction motors from
from Hoyer:
Hoyer: Re-check the alignment after the final
final tightening
tightening of
of the
the
Re-check the alignment after the
HMA2, HMC2,
HMA2, HMC2, HMD,
HMD, HMT,
HMT, MS,
MS, Y2E1,
Y2E1, Y2E2,
Y2E2, YDT
YDT bolts or
or studs.
studs.
bolts
These motors
These motors are
are manufactured
manufactured in in accordance
accordance with
with IEC/EN
IEC/EN Check that
that drain
drain holes
holes and
and plugs
plugs face
face downwards.
downwards. WeWe
Check
60034-4 and
60034-4 and IEC/EN
IEC/EN 60072.
60072. recommend opening the drain hole for motors placed
recommend opening the drain hole for motors placed
Motors are
Motors are rated
rated for
for the
the ambient
ambient temperature
temperature range
range -20°C
-20°C outdoors and
and not
not running
running 2424 hours
hours // day,
day, so
so that
that the
the motor
motor
outdoors
to +40°C
to +40°C and
and site
site altitudes ≤1000 m
altitudes ≤1000 m above
above sea
sea level.
level. can breathe,
breathe, thus
thus ensuring
ensuring a a dry
dry motor.
motor.
can
Low-voltage motors
Low-voltage motors are are components
components for for installation
installation in
in
machinery. They are CE marked according
machinery. They are CE marked according to the Low to the Low
Voltage Directive
Voltage Directive 2006/95/EC
2006/95/EC 4. Electrical connection
Work is
Work is only
only permitted
permitted to to be
be carried
carried out
out by
by qualified
qualified
2. Transport and storage specialists
specialists and
and must
must toto be
be carried
carried out
out in
in accordance
accordance with
with
Check thethe motor
motor forfor external
external damage
damage immediately
immediately upon
upon local
local regulations.
regulations.
Check
receipt and,
and, ifif found,
found, inform
inform the
the forwarding
forwarding agent
agent right
right Before work
Before work commences,
commences, ensure
ensure that
that all
all power
power is
is switched
switched
receipt
away. Check
Check allall rating
rating plate
plate data,
data, and
and compare
compare itit with
with the
the off
off and
and cannot
cannot be
be switched
switched on on again.
again. This
This also
also applies
applies to
to the
the
away.
requirement of the motor. auxiliary power circuits, e.g. anti-condense heaters.
auxiliary power circuits, e.g. anti-condense heaters.
requirement of the motor.
Turn the
the shaft
shaft byby hand
hand toto check
check free
free rotation,
rotation, remove
remove Check that
Check that supply
supply voltage
voltage and
and frequency
frequency are are the
the same
same as
as
Turn
transport locking
locking ifif used.
used. rated data.
rated data.
transport
Transport locking
locking must
must be
be used
used again
again for
for internal
internal transport
transport Motors
Motors can
can be
be used
used with
with aa supply
supply deviation
deviation ofof ±
± 5%
5% voltage
voltage
Transport
also. It
It is
is also
also important
important that
that transport
transport locking
locking is
is used
used when
when and ± 2% frequency, according to IEC60034-1
and ± 2% frequency, according to IEC60034-1
also.
motors are
motors are transported
transported mounted
mounted onon equipment.
equipment.
All motors
motors should
should be be stored
stored indoors,
indoors, in
in dry,
dry, vibration-
vibration- and
and Connection
Connection diagrams
diagrams for
for main
main supply
supply and
and accessory
accessory as
as PTC
PTC
All
dust-free conditions. or heater are located inside the terminal box.
or heater are located inside the terminal box.
dust-free conditions.
Lifting eyebolts
eyebolts must
must be
be tightened
tightened before
before use.
use. Damaged
Damaged Connections
Connections must
must bebe made
made inin such
such a
a way
way as
as to
to ensure
ensure that
that
Lifting
eyebolts must not be used, check before use. Lifting eyes at
at a permanently safe electrical connection is maintained,
a permanently safe electrical connection is maintained,
eyebolts must not be used, check before use. Lifting eyes
motor must
must not
not be
be used
used to
to lift
lift the
the motor
motor when
when it
it is
is attached
attached both for
both for the
the main
main supply
supply and
and the
the earth
earth connection.
connection.
motor
to other
other equipment.
equipment. We recommend
We recommend that that crimped
crimped connections
connections are
are made
made inin
to
accordance
accordance with
with IEC
IEC 60352-2.
60352-2.
Before commissioning,
Before commissioning, measure
measure the
the insulation
insulation impedance.
impedance.
If values
values are ≤ 10MΩ
are ≤ 10MΩ at
at 25°C,
25°C, the
the winding
winding must
must be
be oven
oven dried.
dried. Tightening torques
Tightening torques for
for terminal
terminal board
board screws:
screws:
If
The insulation
The insulation resistance
resistance reference
reference is
is halved
halved for
for each
each 20°C
20°C Thread M5 M6 M8 M10 M12 M16 M20
Thread M5 M6 M8 M10 M12 M16 M20
rise in motor temperature.
rise in motor temperature. T.(Nm)
T.(Nm) 2.5
2.5 3.5
3.5 7
7 12
12 18
18 35
35 55
55
It is
It is recommended
recommended thatthat shafts
shafts are
are rotated
rotated periodically
periodically by
by
hand to
hand to prevent
prevent grease
grease migration.
migration.
Ensure
Ensure that
that the
the terminal
terminal box
box is
is clean
clean and
and dry.
dry.
Unused glands
Unused glands must
must be
be closed.
closed.
3. Installation Check the
Check the terminal
terminal box
box gasket
gasket before
before it
it is
is remounted.
remounted.
The motor
The motor must
must bebe fixed
fixed on
on aa stable,
stable, clear
clear and
and flat
flat founda-
founda-
tion. It
tion. It must
must be
be sufficiently
sufficiently rigid
rigid to
to withstand
withstand possible
possible short
short 5. Maintenance
circuit forces.
circuit forces.
It is
is important
important to to ensure
ensure that
that the
the mounting
mounting conditions
conditions do
do Inspect the
Inspect the motor
motor at
at regular
regular intervals,
intervals, keep
keep it
it clean
clean and
and
It
not cause
cause resonance
resonance with
with the
the rotational
rotational frequency
frequency andand the
the ensure
ensure free
free ventilation
ventilation air
air flow,
flow, check
check the
the condition
condition ofof
not
doubled supply
supply frequency.
frequency. shaft
shaft seals
seals and
and replace
replace if
if necessary.
necessary. Both
Both electrical
electrical and
and
doubled
Only mount
mount or or remove
remove drive
drive components
components (pulley,
(pulley, coupling,
coupling, mechanical connections
mechanical connections must
must bebe checked
checked and
and tightened
tightened if
if
Only
etc.) using
using suitable
suitable tools,
tools, never
never hit
hit the
the drive
drive components
components necessary.
necessary.
etc.)
with a
with a hammer
hammer as as this
this will
will cause
cause damage
damage to to the
the bearing.
bearing.
The motor
The motor areare balancing
balancing with
with half
half key,
key, ensure
ensure that
that the
the drive
drive
components are
components are also
also the
the same.
same.
2
30 4
2 Hoyer Motors,
Hoyer Motors, Motor
Motor Manual,
Manual, October
180R9264October
2011
/ IOM APP2011
11-13 Appendices - v04 / 11.2013
180R9264 / IOM APP 11-13 Appendices - v04 / 11.2013 31
SVEND HØYER A/S
Chains · Gears · Motors
Tlf. (+45) 86 98 21 11
motorinA5-10 OUTL.indd 40 16/11/05 11:58:16
Lenntech
[email protected]
Tel. +31-152-610-900
+31-152-610-900
www.lenntech.com
Fax.+31-152-616-289
+31-152-616-289
4. Recommended service
intervals for APP
pumps (180R9199)
Instruction
Recommended service intervals

for APP pumps
Instruction Recommended service intervals for APP pumps
Table of Contents 1. General information
Recommended service 2. Design/features

intervals for APP pumps
(180R9199) 3. Appendix 1
1. General information This guideline provides information on the The recommendation is for guidance only.
recommended service intervals. The recommen-
dation is based upon good engineering practice
and on experience gained from operation even
under extreme conditions.
2. Design/features Danfoss APP pumps are designed for long If the Danfoss recommendations concerning
operation and low maintenance and life cycle system-design (see our data sheet) are not
costs. followed, the service life of the APP pumps might
be affected.
Danfoss guarantees 8,000 hours service free
operation, however max. 18 months from date of The recommended service intervals on the
production. After 8,000 operation hours it is different parts in the APP pumps appear from the
recommended to inspect the pump and replace table below:
worn parts, if any.
Pos. Qty. Description Material Service interval

1 1 Housing, main bearing Duplex, PEEK No need for service
11, 125, 1 Mounting flange/ Wetted part: Duplex No wear part
211* end flange Dry part: AISI 316L
121, 181* 1 Port flange Duplex No wear part
31 1 Swash plate Super Duplex 40,000 hours
66 5/7/9 Piston Super Duplex and PEEK Recommended inspection
on a yearly basis and
evaluated acc. to app. 1
92 1 Valve plate Super Duplex 24,000 hours
91 1 Port plate Super Duplex, PEEK 24,000 hours
61 1 Cylinder barrel Super Duplex 40,000 hours
65 1 Retainer plate Super Duplex 24,000 hours
64 1 Retainer ball Super Duplex 40,000 hours
71 1 Retainer guide Super Duplex 40,000 hours
62 1/4 Spring Duplex 40,000 hours
63 1 Spring guide Duplex or PP 40,000 hours
142 1 Stop for shaft seal PP No wear part
124, 215* 1 Shaft seal Hastelloy and NBR It is good practice to
change the seal after each
disassembly of the pump
125 1 Cover/flange for shaft seal Super Duplex No wear part
93 5/7/9 Back-up ring PTFE 24,000 hours
* O-ring (overall) NBR 24,000 hours
* Screw (overall) AISI 316 No wear part
* Pin (overall) AISI 316, Duplex or PEEK No wear part
152 1 Valve cone (flushing valve) Duplex or PEEK 40,000 hours
3, 129* 2 Bleeding screw Duplex No wear part
67 1 Key AISI 316 40,000 hours
* depends on pump size
34
2 180R9264 / 521B1135
/ DKCFN.PI.013.C1.02 11.2013
3. Appendix 1 Pistons: In case of doubt - the pistons must be replaced.

The pistons are the heart of the pump regarding
service. The pictures below is ment as a guideline for
evaluating the wear of the sliding surface.
If the pistons break down, the pump will suffer a
breakdown.
Cavitation of the piston shoes. Cavitation of the piston shoes.

New inspection is required in 3,000-4,000 hours. All pistons must be replaced within the next
500-1,000 hours.
Cavitation of the piston shoes. Cavitation of the piston shoes.

All pistons must be replaced within the next All pistons must be replaced immediately.
100-200 hours.
Abrasive wear of the piston shoes.

All pistons must be replaced immediately.
180R9264 / 521B1135
/ DKCFN.PI.013.C1.02 11.2013 35
3
Danfoss A/S
High Pressure Pumps
DK-6430 Nordborg
Denmark
36
4 180R9264 / 521B1135
/ DKCFN.PI.013.C1.02 11.2013
5. APP parts list

(521B0941)
Parts list
APP Pumps
APP 0.6-43
11-13 / APM 0.8-2.9 /
APP W 5.1- 10.2
APP 11-13
Parts list APP 0.6-43 / APM 0.8-2.9 / APP W 5.1-10.2
Table of Contents 1. General
Parts list APP 21-43 2. Parts list APP 0.6 - 1.0 Compact
(521B0941)
3. Exploded view APP 0.6 - 1.0 Compact
4. Parts list APP 0.6 - 1.0 and APM 0.8 - 1.2
5. Exploded view APP 0.6 - 1.0 and APM 0.8 - 1.2
6. Parts list APP 1.5 - 2.5 and APM 1.8 - 2.9
7. Exploded view APP 1.5 - 2.5 and APM 1.8 - 2.9
8. Parts list APP 3.0 - 3.5
9. Exploded view APP 3.0 - 3.5
10. Parts list APP 5.1 - 10.2
11. Exploded view APP 5.1 - 10.2
12. Parts list APP W 5.1 - 10.2
13. Exploded view APP W 5.1 - 10.2
14. Parts list APP 11 - 13
15. Exploded view APP 11 - 13
17. Exploded view APP 16 - 19
18. Parts list APP 22
19. Exploded view APP 22
21. Exploded view APP 21 - 26 Not included
23. Exploded view APP 30/1200 and APP 43/1700
24. Tool sets
38
2 180R9264 // DKCFN.PC.073.A13.02
/ 10.2013
1. General This parts list provides an overview of the

content of the various service sets for the
• APP 0.6-1.0 Compact

• APP 0.6-1.0
• APM 0.8-2.9
• APP 1.5-2.5
• APP 3.0-3.5
• APP 5.1-10.2
• APP W 5.1-10.2
• APP 11-13
• APP 16-22
• APP 21-43
as well as exploded views of the pumps.
180R9264
521B0941 // DKCFN.PC.073.A13.02
IOM APP 11-13 Appendices - v04 / 11.2013
/ 10.2013 39
3
14. Parts list Note:

APP 11 - 13 The parts listed are not sold
(APP 11 / 1200 rpm, APP 13 / 1500 rpm)

separately, only in various kits.
180B4228 – Cylinder barrel set

Exploded view, see next page.
180B4227 – Flushing valve set

180B4226 – Swash plate set

180B4204 – Valve plate set
180B4201 – Retainer set
180B4221 – Piston set

180B4229 – Seal set
(APP 13 / 1200 rpm)

(APP 11 / 1500 rpm)
Pos. Qnt. Designation Material
(APP 11-13)
(APP 11-13)
(APP 11-13)
(APP 11-13)
(APP 11-13)
(APP 11-13)
1 1 Housing Duplex / PEEK
2 2 Pin (Ø6x10) AISI 316 x
3 2 Bleeding plug Super Duplex x
4 2 O-ring (Ø11x2) NBR x
5 12 Screw (M8x30) AISI 316 x x
9 1 O-ring (Ø182x4) NBR x x
10 2 O-ring (Ø9.19x2.62) NBR x x x x
11 1 End flange Duplex
12 1 Lifting eye AISI 316
31 1 Swash plate Super Duplex / PEEK x x x
34 2 Pin (Ø10.5x20) Super Duplex x x x x
61 1 Cylinder barrel Super Duplex / x
Duplex / PEEK
62 7 Spring Duplex x
63 1 Spring guide PP x
64 1 Retainer ball Super Duplex / DLC x
65 1 Retainer plate Super Duplex x
66 7 Piston Super Duplex / PEEK x
67 1 Key (10x8x45) AISI 316 x
81 3 Pin (Ø6.4x40) Duplex x
91 1 Port plate Super Duplex / PEEK x
92 1 Valve plate Super Duplex x
93 7 Back-up ring PTFE x x
94 7 O-ring (30.2x3.0) NBR x x
121 1 Port flange Duplex / PEEK
124 1 Shaft seal (Ø35) Hastelloy / NBR x
125 1 Cover for shaft seal Super Duplex
126 2 Pin (Ø10.5x20) Duplex x x
127 4 Screws (M6x16) AISI 316 x
128 10 Screws (M8x65) AISI 316 x
129 1 Lifting eye AISI 316
142 1 Stop for shaft seal PP x
144 4 Tailstock screw (M12x60) AISI 316
145 4 Check nut (M12) AISI 316 x
151 1 O-ring (Ø29x3) FPM 75 x x
152 1 Valve cone Super Duplex x
153 1 Spring (Ø1.9xØ25x33.7) Duplex x
154 1 Plug/guide Super Duplex x
155 1 O-ring (Ø38x3.7) NBR x x
Instruction x x x x x x x x x
40
16 180R9264 // DKCFN.PC.073.A13.02
/ 10.2013
15.
Parts list
APP 11 - 13
Exploded view
180R9264
[22.13 lbf ft
± 2.21 lbf ft]
[1.47 lbf ft
± 0.74 lbf ft] [22.13 lbf ft ± 2.21 lbf ft]
521B0941 // DKCFN.PC.073.A13.02
IOM APP 11-13 Appendices
[1.47 lbf ft
± 0.74 lbf ft]
/ 10.2013
- v04 / 11.2013
[22.13 lbf ft
± 2.21 lbf ft]
APP 0.6-43 / APM 0.8-2.9 / APP W 5.1-10.2
[7.38 lbf ft ± 1.47 lbf ft]
[1.47 lbf ft ± 0.74 lbf ft]
[7.38 lbf ft ± 1.47 lbf ft]

[22.13 lbf ft ± 2.21 lbf ft]
[7.38 lbf ft ± 1.47 lbf ft]
17
41
24. Tool sets Note:
180B4188 – Tool set (APP 0.6-1.0 Compact)

The parts listed are not sold
separately, only in various kits.
180B4162 – Tool set (APP 5.1-10.2)

180B4148 – Tool set (APP 1.5-3.5)
180B4142 – Tool set (APP 0.6-1.0)
180B4222 – Tool set (APP 16-22)

180B4172 – Tool set (APP 21-43)
180B4230 – Tool set (APP 11-13)
Designation
Shaft bush x
Press bush x
Drift x
Torx (T30) x
Shaft bush (Ø18) x x
Press bush (Ø18) x x
Allen key (4 mm) x
Allen key (5 mm) x
Allen key (6 mm) x x x x
Shaft bush (Ø35) x
Shaft seal extractor (Ø35) x x
Adjustable pin wrench x x x x
Combination wrench (10 mm) x x x x
Combination wrench (13 mm) x x x
Nut (M8x6.5x13) x x x
Guide bolt (M8x140) x x
Shaft seal extractor (Ø45) x x
Eye bolt (M8) x x
Press bush for valve plate x x
Stop for retainer plate x
Screw (M8x20) x x x
Screw (M8x70) x x
Danfoss A/S
High Pressure Pumps
DK-6430 Nordborg
Denmark
42
26 180R9264 // DKCFN.PC.073.A13.02
/ 10.2013
6. Trouble shooting guide
Guideline
Trouble shooting guide

for APP, APP S and APP S 674 pumps
Instruction Trouble shooting guide for APP, APP S and APP S 674 pumps
Table of Contents Trouble shooting fish bone chart
Trouble shooting 1. No flow/no pressure

guide for
APP, APP S and 2. Reduced flow/reduced pressure
APP S 674 pumps
3. High torque on electric motor
4. Noise from pump
5. Noise from installation
6. Typical signs of wear

6.1 Valve plate
6.2 Port plate
6.3 Swash plate
44
08.2013
Instruction
fish bone chart

Trouble shooting
08.2013
1. No flow/pressure 2. Reduced flow/pressure
2.1.5 Pre-treatment
1.1 Dry running 2.1.6 Main filtration
1.2 Pump reversing 2.1 Wear in pump

(internal leakage)
1.3 No rotation of electric motor 2.1.7 Fluid type
1.4 No rotation of pump 2.1.8 High fluid temperature
1.5 Axial force on pump shaft 2.2 Low inlet pressure

1.6 Pump damage 2.3 RPM
PUMP FAILED
3.1 Too high outlet pressure 5.1 Inlet/outlet connections

4.1 Air in fluid
from pump (hoses/pipes)
5.2 Length/dimensions of
3.2 Pump starts against pressure 4.2 Bleeding conditions of pump
inlet/outlet line
4.3 Min/max nominal
3.3 Constant torque 5.3 Hose stiffness
inlet pressure
5.4 Hoses/pipes mounted
Trouble shooting guide for APP, APP S and APP S 674 pumps
3.4 Water pump damage 4.4 Pump reversing

directly on frame
5.5 Vibration damper under the
4.5 High rotation speed (RPM)
electric motor
4.6 Outlet pressure
4.7 Soft start/stop
3. High torque on el. motor 4. Noise from pump 5. Noise from installation
45
3
1. No flow/no pressure
Cause Remedy Comments

1.1 Dry running If no water comes out of the pump: Mount a low pressure switch in front of the
(no water supply to the pump) pump and check its set point/ function. The low
1.1.1 Check that inlet valve is open. pressure switch ensures that the pump does
1.1.2 Check that booster pump is running. not start until the inlet pressure has reached-
minimum inlet pressure (see User manual).
1.2 Pump reversing 1.2.1 Change the phase on the electric motor to Rotation direction for the APP, APP S or APP S 674
(electric motor is running the wrong direction, make it run clockwise. pump is shown by an arrow on the label on the
i.e. counter-clockwise) pump.
WARNING:
- The pump must not run without water for
more than a few seconds.
- If the pump takes in water from the high-
pressure outlet line, it builds up pressure in
pump housing and will eventually break
down.
1.3 No rotation of electric motor 1.3.1 Check that main switch is switched on. If motor-type relay or the electrical fuse is
1.3.2 Check the electricity at the facility. blown, check that electric motor is sized
1.3.3 Ensure that motor relay is switched on. correctly.
1.3.4 Ensure that fuse is not blown.
1.3.5 Ensure that booster pump is started.
1.3.6 Check that the monitor switches are
working correctly.
1.3.7 Disconnect pump from electric motor and
check that the motor is capable of running
with no load.
1.4 No rotation of pump 1.4.1 Ensure that coupling between electric
motor and pump is connected.
1.4.2 Check if coupling is damaged.
1.4.3 Check that electric motor is sized correctly.
1.4.4 Check that the electrical installation is
correctly sized.
1.4.5 Contact Danfoss Sales office for guidelines
in how to troubleshoot internal pump
parts.
1.5 Axial load on pump shaft 1.5.1 Ensure that the air gap between the two To ensure easy mounting of the flexible
(may cause high internal leakage) coupling parts is min 5 mm. It should coupling without using tools, the tolerances
Only applying to always be possible to move the plastic part must be dimensioned accordingly.
APP 0.6 to APP 3.5 and on the coupling at least 3 mm.
APP 21 to APP 26 only. WARNING:
Also applying to APP S and APP S 674 pumps. Any axial and/or radial loads on the shaft
must be avoided. Any axial or radial load will
cause breakdown.
A - Bell housing
B - Flexible coupling
C - Motor shaft
A B C
1.6 Pump damage 1.6.1 Contact Danfoss sales office for guidelines Instructions on internal elements
(the internal parts may be damaged) in how to troubleshoot internal pump 180R9092/180R9085 for APP 0.6-1.0
parts. 180R9091/180R9147/180R9089 for APP 1.5-3.5
180R9093/180R9090 for APP 5.1-10.2
180R9228/180R9227 for APP 11-13 and APP 16-22
180R9121/180R9139 for APP 21-43
180R9281 for APP S 674 3.0-3.5 / APP S 3.0-3.5
180R9280 for APP S 674 5.1-9.0 / APP S 5.1-9.0
180R9278 for APP S 674 21-38 / APP S 21-38
– are available on www.ro-solutions.com.
46
08.2013
2. Reduced flow/reduced pressure

2.1 Wear on pump 2.1.1 Dismantle the pump. Typical signs of wear:
Large internal leakage due to: 2.1.2 Check valve plate. Polished surface all over the swash plate.
Valve plate has marks/scratches on the Normally, only half of the swash plate = the
surface facing the port plate. Minor wear pressure side is polished. See index 6.3.
on valve plate can cause large internal
leakage. See Index 6.1. If the ring is missing, the piston is very worn.
2.1.3 Check port plate.
Port plate has marks/scratches on the
surface facing the valve plate. Minor wear
on port plate can cause large internal
leakage. See Index 6.2.
2.1.4 Check cylinder barrel.
Liners in cylinder barrel may be scratched
or worn. Insert a piston in the liner and
check the fit. If there is any space
(clearance) between liner and piston, liner
or piston is worn.
2.1.5 Pre-treatment
Analyse fluid for content of particles.
- Check that filters are OK and working
correctly.
2.1.6 Main filtration
Check that the correct filter type is used The filters can be bypassed, even if they are
(particles in fluid must not exceed 10 μm). correctly mounted. Some filters can create
Danfoss High Pressure Pumps supplies channelling where particles can pass through
filters, please contact the sales office. the filter in tunnels. String wounded filters are
typically channelling filters. A string wounded
filter may have a filtration efficiency of only
50%, which will cause internal wear and must
always be followed by a main filter.
2.1.7 Fluid type

The APP, APP S and APP S 674 pumps are Insufficient filtration means that too many or
designed for seawater operation; for any too large hard particles can pass the main filter
other fluid, please contact Danfoss High because it is damaged, bypassed or simply too
Pressure Pumps sales office for further help. poor. Filtration efficiency must be 99.98%
(Beta = 5000) at 10 μm to prevent abnormal
wear of the pump.
- 2.1.8 High fluid temperature
If fluid temperature is above 50°C, stop the Temperature > 50° C will cause wear on internal
pump immediately. pump parts. Mount a temperature switch and
check its set point / function. The temperature
switch will ensure that the pump stops at fluid
temperatures > 50° C.
- Check internal parts (see above).

2.2 Low inlet pressure 2.2.1 Check that booster pump supplies the If the pressure drop across the filters is too high,
right pressure/flow. the booster pump does not deliver sufficient
2.2.2 Check if filters require replacement. flow/pressure. No pressure or low pressure
results in cavitation and insufficient internal
lubrication causing wear on internal pump
parts.
Mount a low-pressure switch in front of the

pump and check its set point/ function. The
low-pressure switch ensures that the pump
does not start until the inlet pressure has
reached 1 bar.
2.3 Rotation speed (rpm) 2.3.1 If VFD-operated, check frequency. Speeds below min. limit (see User manual)
2.3.2 Check that rotation speed of the electric result in insufficient internal lubrication causing
motor is as stated on name plate on wear on the internal pump parts.
electric motor. Check that the motor rotor
winding is not damaged.

08.2013 47
5
3. High torque on electric motor

3.1 Too high outlet pressure from pump 3.1.1 Check fluid salinity. Pump conditions may change (more salt, lower
3.1.2 Check temperature. water temperature or scaling of RO membrane)
3.1.3 Check pressure drop across RO membrane. causing higher pressure, resulting in higher
motor torque.
3.2 Pump starts against pressure 3.2.1 Check that electric motor is correctly sized. Pumps run in parallel with cascade start, may
3.2.2 Check internal parts (see item 2.1). switch off the motor relay due to too high
3.2.3 Systems with more than one electric torque caused by high outlet pressure.
motor installed:
Start motors simultaneously.
3.3 Constant torque 3.3.1 Please contact Danfoss High Pressure If the electric motor is too small for the APP, APP S
Pumps sales office. or APP S 674 pump, it cannot provide sufficient
torque.
3.4 Water pump damage 3.4.1 Dismantle pump and check for wear. Too heavy damage in the pump will increase
friction causing a high torque (see item 6,
Typical signs of wear).
48
08.2013
4. Noise from pump

4.1 Air in fluid 4.1.1 Ensure that the entire inlet line is bled Small air bubbles will accumulate and create
before starting up the system. large bubbles causing internal cavitation and
4.1.2 Ensure that air cannot enter into the inlet thus making the pump very noisy.
line.
WARNING:
The pump can only run few minutes with air in
the fluid without being damaged.
4.2 Bleeding conditions of pump 4.2.1 Follow the instructions “Initial start-up” The pump and the inlet line must be com-
supplied with the new pump. pletely bled before start-up, otherwise the
4.2.2 Ensure that the pump is completely bled pump will cavitate and make high noise.
before start-up.
WARNING:
The pump can only run few minutes with air in
the fluid without being damaged.
4.3 Min/max nominal inlet pressure 4.3.1 Ensure that inlet pressure is within the Too high inlet pressure causes too high
limits specified in the User manual. pressure inside the pump damaging the pistons
4.3.2 Check the pump for internal damage. and eventually the pump.
Inlet pressure below min. limit causes cavitation

and insufficient internal lubrication resulting in
wear on internal pump parts.
Mount a low-pressure switch in front of the

pump and check its set point/ function. The
low-pressure switch will ensure that the pump
does not start until the min. inlet pressure has
been reached.
4.4 Pump reversing 4.4.1 Dismantle pump and check if anything is If pump rotates in wrong direction, it will take in
broken or worn (See “1. No flow”, item 1.2 water from the high-pressure outlet line.
Pump reversing”). Pressure will be built up inside the pump and it
will eventually be damaged.
WARNING:
The pump must not run without water
for more than a few seconds. If the pump
takes in water from the high-pressure
outlet line, it builds up pressure and will
eventually be damaged.
4.5 High rotation speed (rpm) 4.5.1 If electric motor rpm is too high, dismantle Higher rpm than specified in the pump data
pump and check for damage. sheet results in wear of the pistons, i.e. pistons
4.5.2 If the rpm is within the specified range of may be damaged.
the pump data sheet and abnormal noise
remains, dismantle pump and check for High rpm will also increase pressure pulsations
damage. from the pump, and the noise level will
increase.
If rpm is changed, noise frequency will also

change.
4.6 Outlet pressure 4.6.1 If outlet pressure is too low, check set At too low outlet pressure, the pump will create
point of outlet pressure valve. higher pressure pulsations and thus make
4.6.2 If outlet pressure is lower than mentioned noise. Too low pressure also causes insufficient
in the pump data sheet, please contact internal lubrication and wear on internal parts.
Danfoss High Pressure Pumps technical Pump may eventually be damaged.
support.
4.6.3 If outlet pressure has exceeded its Too high outlet pressure may damage the
maximum, check set point of outlet pump.
pressure valve.
4.6.4 Check internal parts for wear/damage.
4.7 Soft start/stop 4.7.1 Check if noise is normal when the pump is Noise frequency changes during soft start-up/
running at operation speed. stop.
4.7.2 If noise is abnormal at operation speed,
check internal parts (see above).

08.2013 49
7
5. Noise from installation

5.1 Inlet/outlet connections (hoses/pipes) 5.1.1 Use flexible hoses at inlet/outlet connec- Non-flexible connections mounted directly on
tions. Danfoss can provide flexible hoses. the frame will cause even small pressure
Please contact Danfoss High Pressure pulsations from pump and create vibrations in
Pumps sales office for further information. the system/plant.
5.1.2 Mount the connections to the frame by a
vibration dampener mounting plate.
5.2 Length/dimension of inlet/outlet line 5.2.1 Increase pipe diameter and/or reduce the Too small pipes or too many bends may create
number of bends. too fast flow/turbulence through the pipes and
thus increase the noise level.
5.3 Hose stiffness 5.3.1 Use a more flexible hose. Danfoss can Too stiff hoses cannot dampen the small
provide flexible hoses. Please contact pressure pulsations from the pump, and
Danfoss High Pressure Pumps sales office subsequently vibrations occur in the system/
for further information. plant.
5.4 Hoses/pipes mounted directly on frame 5.4.1 Mount the connections to the frame by a If the hoses are mounted directly on the frame,
vibration dampener mounting plate. the small pressure pulsations from the pump
can be transferred to the frame and the rest of
the system/plant.
5.5 Vibration dampener under the electric 5.5.1 Mount a vibration dampener below the When no dampener is installed below the
motor motor/pump. electric motor, vibrations from the motor and
pump may be transferred to the frame and the
rest of the system/plant.
50
08.2013
6. Typical signs of wear

6.1 Valve plate
Picture 1 A normally worn valve plate has no marks/scratches but only a slightly
polished surface.
No scratches or marks should be felt. The surface must be flat and level.
Picture 2 A worn valve plate has scratches, and/or a polished surface. Even small
scratches will give a loss of flow.
Scratches
Picture 3 A good way to identify a worn valve plate is to hold a straight knife edge
over the valve plate. When holding it up to the light, it will be possible to
see any space between the knife edge and the valve plate. See picture 3.
If any light can be seen between the two arrows on the picture, the valve
plate is worn.
If any scratches or marks can be felt by running a fingernail over the surface,
the valve plate is worn.
The valve plate on picture 3 is highly damaged.

08.2013 51
9
6.2 Port plate
Picture 1 If the port plate has scratches, level differences or both between the arrows,
the port plate must be replaced.
S cr Even small scratches or wear will cause loss of flow.

atc
h es
To check: See item 6.1, picture 3
L ev
dul el diff
l an e re
d sh nce
inin s b e
g P t we
EEK e n
6.3 Swash plate
Picture 1 If the swash plate is polished 360°, it is an indication of insufficient filtration.
The surface of the swash plate must be plane and even at same level all
over. To check this, please see item 6.1, picture 3.
If the surface has any marks/scratches, it is worn/damaged and a new one

is required.
Please contact Danfoss High Pressure Pumps sales office for further infor-
mation.
Danfoss A/S
High Pressure Pumps
DK-6430 Nordborg
Denmark
52
08.2013
7. Right and wrong

(180R9042)
Right and wrong

Trouble shooting guide for water hydraulic systems
180R9042
4. Pump location
Design
Pump always to be placed below water Pump location above water surface
surface level level will cause damage
1. Choice of material 5. Suction conditions
. Iron
. Rubber . Copper
. Plastic . Brass
. Stainless steel . Aluminium
Always use system components made Non-corrosion proof materials System to be dimensioned to provide Poor suction conditions will cause
of corrosion proof materials may cause damage a suction pressure of the pump inlet of malfunction and damage the pump
max. 0.1 bar vacuum
2. Choice of filter 6. Pressure Relief valve
< 10 mm abs. > 10 mm
Install a 10 micron absolute filter with Return filter with bypass valve and Pressure relief valve to be mounted Coupling the pressure relief valve outlet
pressure switch poorer filterability than 10 m will vertically or with vertical outlet and directly to the pump inlet may damage
damage the system connected to return hose or tank the pump
3. Filter location 7. Water supply
Locate the return filter in the return line Placing the return filter upstream of the System to be filled via filter Filling system with unfiltered
immediately before the tank final load may damage the pump water causes damage
Installation
Assembly of coupling
8. Impurities 11.
Prior to installation, burrs and chips and Chips or other impurities in the system The coupling must be easy and simple Never use force when assembling the
other impurities must be removed from may cause damage to assemble (see product instruction) coupling parts, as this will damage the
pipes and hoses, eg with a felt plug motor/pump
Coupling
9. Sealing 12.
= min. 3 mm 0 mm
Fittings in screwed components to be Using teflon tape or packing yarn in Ensure always to have 3 mm distance Insufficient distance and/or misalign-
sealed with O-rings or bonded seals joints may cause damage between coupling flanges ment between the coupling flanges
will damage the pump
Grease Water supply

10. 13.
Correctly limited quantities of grease Too much grease may develop Fill system with water before starting Starting without water will cause
prevent seizing biofilm causing operational failures to ensure lubrication and cooling damage
Wiring
Starting procedure
Cleaning procedure
Level indicator 1. Fill cold water into the system via the return filter and
14. bleed the pump (Power Packs PPH 4 - 6.3 - 10 and 12.5 are
self-bleeding)
2. Start and bleed the system -without pressure by opening

the bypass valve
3. Add the cleaning agent to give 3% agent/water solution
4. Run the system for 60 min. and activate all components as

often as possible to ensure effective flushing with the
cleaning agent
Level and temperature indicators Missing or incorrectly connected level 5. Empty the system of the cleaning agent solution
must be fitted. Follow installation and temperature indicators cause
instructions damage
Flushing procedure
6. Fill cold water through the return filter and bleed the
15. Rotation direction pump (Power Packs PPH 4 - 6.3 - 10 and 12.5 are
self-bleeding)
1 ? 2
7. Run the system for 30 min. and activate all components as
often as possible
8. Empty the system of the water
9. Alternatively the system may be flushed by running the

unit without the return hose while continuously filling up
water. The flushing should continue until there is no trace
of cleaning agent in the return water
Check pump drive motor rotation Incorrect rotation direction will
direction matches that of the pump damage the pump 10. Change the return filter element, fill cold water through
prior to installation
the return filter and bleed the pump during start up
11. The system is now ready for operation
Bleeding
16. Starting procedure
60 min. 2-3
days
Bleeding the pump will ensure correct Insufficient bleeding may cause dam- Observing the starting procedure will If the system is not cleaned before
cooling and lubrication age (not applicable to Power Packs) ensure problem-free operation starting, the filter will clog
Trouble shooting
Open ended water systems
No water supply
. Is the water supply ok?

No
. Is water supplied to the pump?
Yes
. Is water coming . Is the electric motor of . Is the water in the tank . Lower inlet
No o Yes temperature or
No out of the tap? the pump unit rotating? very hot? Ie above 50
provide better cooling
. Are all taps open?
Yes No
Yes
. Is the control light . Is the power supply ok?

No
Yes
for “low pump suction . Are control lights on?
pressure” on?
. The filter is clogging
Yes
No
. Is the filter clogged?

No . Is the filter control
. Is water coming light on?
Yes
through the filter?
Yes
. A blown fuse / or short
No
circuit?
. Check power supply
. Replace filter element and fuses and contact
electrician
. Replace filter element
Contact serviceman
. Turn on the tap for

water supply
Stamp
Trouble shooting
Closed water systems
The system
does not work
. Is there sufficient water

No
in the tank?
Yes
. Is the electric motor of . Is the water in the tank

No Yes
the pump unit rotating? very hot? Ie above 50o
Yes No
. At temperatures
o
higher than 50 the
. Is the power supply ok? pump drive cuts out.
No Consequently the
. Are control lights on?
cooler must be
checked/cleaned
Yes
. A blown fuse/or short

circuit?
. Check power supply . Is the filter clogged?

. Fill water into the system and fuses and contact . Is the filter control Yes . Replace filter element
electrician light on?
No
Contact serviceman
. Trace leakage, if any
Stamp
DKCFN.PI.000.C2.02 180R9042 521B0288

180R9264 / IOM APP 11-13 Appendices - v04 / 11.2013 59

Contact information Danfoss A/S
Lenntech
[email protected]
Tel. +31-152-610-900
+31-152-610-900
www.lenntech.com
Fax.+31-152-616-289
+31-152-616-289

Danfoss IOM APP 11 13 L

Uploaded by

Copyright:

Available Formats

Danfoss IOM APP 11 13 L

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Danfoss IOM APP 11 13 L

Uploaded by

Copyright:

Available Formats

MAKING MODERN LIVING POSSIBLE

Installation, Operation and

Table of Contents Validity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

4. Arrival inspection, transportation, handling, lifting and storage . . . . . . . . . . . . . . . . . . . . . . . . . . 9

5. Installation and commissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

6. Operation of pump unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

2 180R9264 / IOM APP Pumps - v03 / 11.2013

7. Maintenance and service of the pump unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

8. Troubleshooting and scrapping criteria . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Appendices for Installation, Operation and Maintenance Manual

1. Data sheet for APP 11-13 pumps (521B1215) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

2. APP pump instruction APP 11-13 (180R9223) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

3. IOM Electric motors (180R9230) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

4. Recommended service intervals for APP pumps (80R9199) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

5. APP parts list (521B0941) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

6. Trouble shooting guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

7. Right and wrong (180R9042) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

180R9264 / IOM APP Pumps - v03 / 11.2013 3

APP 11/1200 Code no. 180B3212

4 180R9264 / IOM APP Pumps - v03 / 11.2013

180R9264 / IOM APP Pumps - v03 / 11.2013 5

1. Introduction 1.1 General

In case the pump delivered is ATEX certified, the

Electrical hazard - Indicates a high-­

All personnel being responsible for operation

• Transportation of the pump unit  Hearing protection required

It is the responsibility of the safety officer or

Electrical Electrical hazard

Changing the pumps’ or pump units’ opera-

•  hanges to the delivered pump or motor

6 180R9264 / IOM APP Pumps - v03 / 11.2013

1.3 Manufacturer and customer service

Danfoss A/S Your local Danfoss pump distributor can be

2.1 General information Under certain operational conditions the surface

It is recommended to install a lockable circuit

Protect the motor and other electrical equip-

180R9264 / IOM APP Pumps - v03 / 11.2013 7

2.4 Adhere to the following important

3. Technical data 3.2 Application range

3.3 Electric motor data

3.4 Noise and vibration

3.1 Approved applications and operational

Use of the pump in other applications not

For system integration of the pump, please see

8 180R9264 / IOM APP Pumps - v03 / 11.2013

3.7 Filtration 3.9 Air bubbles

It should be possible to monitor the condition of

3.8 Properties of water

4. Arrival inspection, 4.1 Arrival inspection 4.4 Transport and handling

In case of damage and/or missing parts, a report

4.3 General safety information

180R9264 / IOM APP Pumps - v03 / 11.2013 9

Pumps which have a weight above 20 kilos (see Wrong lifting:

When lifting the pump unit, one sling must be

Some motors and pumps have specific lifting

Do not use connections/nozzles for lifting!

Make sure that the unit/load is balanced before

See below examples of where to/not to attach

4.5 Return to supplier

Electrical hazard - Indicates a high-

• Transportation of the pump unit Hearing protection required

Electrical Electrical hazard

• hanges to the delivered pump or motor

1.3 Manufacturer and customer service

2.4 Adhere to the following important

3.1 Approved applications and operational

4. Arrival inspection, 4.1 Arrival inspection 4.4 Transport and handling

5.6 Pre mounting checklist, based on Danfoss preferred system design

5.12 Ensure free flow 5.17 Commissioning

5.15 Bleed and remove air from the pump

5.16 Verify direction of rotation

F) Slowly unscrew and remove the bolts and

G) Attach the lifting equipment to the pump

C) Inspect all parts including shaft seal and if

D) If the pump is going to be returned to