Scribd
Upload
37 views2 pages

Absolute Maximum Ratings: Functional Block Diagram

The A1281 is a low sensitivity, unipolar Hall effect switch with a low operating voltage. It has an operating voltage range of 3-24V, and output open drain. The switch has a typical supply current of 2.5mA and turns on at a magnetic flux density above 175 Gauss and turns off below 130 Gauss, with a 45 Gauss hysteresis. It is available in both an SIP-3 and SOT-23 package.

Uploaded by

BIMO MODELADO
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
37 views2 pages

Absolute Maximum Ratings: Functional Block Diagram

The A1281 is a low sensitivity, unipolar Hall effect switch with a low operating voltage. It has an operating voltage range of 3-24V, and output open drain. The switch has a typical supply current of 2.5mA and turns on at a magnetic flux density above 175 Gauss and turns off below 130 Gauss, with a 45 Gauss hysteresis. It is available in both an SIP-3 and SOT-23 package.

Uploaded by

BIMO MODELADO
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

A1281 Specification

Low Sensitivity Unipolar Hall Effect Switch

A1281 is an Unipolar Hall switch of low operating voltage and low sensitivity.

DMOS Hall Supply Voltage Bop：175 Gauss Output Package


SIP-3(I3)
Effect Switch 3.0 ~ 24V Brp：130 Gauss Open Drain SOT-23(S3)

 Absolute Maximum Ratings Functional Block Diagram


At (Ta=25℃)
Characteristics Values Unit
VDD Out
Supply voltage (VDD) 28 V
Output Voltage,(Vout) 28 V
Voltage
Output current, (ISINK) 50 mA Regulator

Operating Temperature
-40 ~ +125 ℃
Range, (TA) Amp
Storage temperature
-55 ~ +150 ℃
Range, (TS)
Hall
Sensor Clock

Package Power
606 / 230 mW
Dissipation, (PD) VSS

Electrical Specifications
DC Operating Parameters： TA=+25℃, VDD=12V
Parameters Test Conditions Min Typ Max Units
Supply Voltage,(VDD) Operating 3.0 24.0 V
Supply Current,(IDD) B<BOP 2.5 5.0 mA
Output Saturation Voltage, (VDSON) Iout=20mA,B>BOP 500.0 mV
Output Leakage Current, (Ioff) IOFF B<BRP, VOUT = 20V 10.0 uA
Output Rise Time, (TR) RL=1kΩ, CL =20pF 0.04 0.45 uS
Output Fall Time, (TF) RL=1kΩ; CL =20pF 0.18 0.45 uS
Electro-Static Discharge HBM 4 KV
Operate Point,(BOP) I3(S3) 140(-250) 250(-140) Gauss
Release Point,(BRP) I3(S3) 95(-205) 205(-95) Gauss
Hysteresis,(BHYS) |BOP - BRP| 45 Gauss

Page 1 of 2
100214 RD-30011
Rev 1.02
A1281 Specification
Low Sensitivity Unipolar Hall Effect Switch

 Package Dimension and Sensor Location

I3 Package
(Top VieW)

NOTES:
1. Controlling dimension: mm
2. Leads must be free of flash and plating voids
3. Do not bend leads within 1 mm of lead to
package interface.
4. PINOUT:
Pin No. Pin Name Function
1 VDD Power Supply
2 VSS Ground
3 VOUT Output

S3 Package
(Top VieW)
NOTES:
1. Controlling dimension: mm
2. Leads must be free of flash and plating voids
3. Lead thickness after solder plating will be
0.254mm maximum
4. PINOUT:
Pin No. Pin Name Function
1 VDD Power Supply
2 VOUT Output
3 VSS Ground

Page 2 of 2
100214 RD-30011
Rev 1.02

You might also like