STERIS Spordex Strips Biological Indicator For Ethylene Oxide and Dry Heat TDS 450 100 5513A

SPORDEX® STRIPS
BIOLOGICAL INDICATOR FOR ETHYLENE OXIDE AND DRY HEAT

TECHNICAL DATA
GENERAL DESCRIPTION
The Spordex Strip Biological Indicator (BI) is produced from filter paper inoculated with a single spore species (Bacillus
atrophaeus, NRRL #B4418) and enclosed in a glassine envelope. The strips are produced under controlled conditions to meet
the suggested performance parameters published in the current United States Pharmacopeia (USP) and ISO 11138-2.
APPLICATION
The Spordex Strip BI is used to validate and re-qualify Ethylene Oxide (EO) gas or dry heat sterilizers and to monitor the
effectiveness of common ethylene oxide gas or dry heat sterilizing processes.
FEATURES BENEFITS
Bacillus atrophaeus single species population Flexibility of use with various sterility level requirements
ranging from E3 to E8 colony forming units (cfu)/strip
Lot number and expiration on each glassine Traceable results and valuable documentation
envelope and data card
Easy-peel glassine pouch Facilitates aseptic transfer
Packaged in plastic boxes Help to protect the product integrity
TECHNICAL PROPERTIES
Primary packaging: glassine envelope approximately 76 x 25 mm (3 x 1")
Spore carrier: filter paper strip approximately 38 x 6 mm (1-1/2 x 1/4")
Species: Bacillus atrophaeus, NRRL #B4418

Mean population recovery: Various (see Ordering Information)
Purity: Bacterial contaminants are less than 1% of labeled population; this is the detection limit using the pour plate method
with an aliquot that yields at least 100 cfu.
*D-value for ethylene oxide (DEO): 2.6 - 4.5 minutes
DEO is determined by a Most Probable Number (MPN) method with a 600 ±30 mg/L ethylene oxide concentration,
54°C (129°F) ±1°C and 50-70% Relative Humidity (RH) and using 100% EO Sterilant.
*D-value for dry heat (DDH): 1.0 - 3.0 minutes
DDH is determined by MPN utilizing 160°C (320°F) ±2°C exposure temperature.
Incubation temperature: 30-35°C (86-95°F)

Shelf life: 18 months from time of manufacture. The expiration date is printed on the glassine envelope and on the data card
that accompanies the box.
Quantity: See Ordering Information
DIRECTIONS FOR USE

After sterilization and aeration processing has been completed according to the sterilizer manufacturer’s instructions, remove
the Spordex Strip BI from the test pack. Aseptically open the glassine envelope. This is accomplished by cutting the glassine
with sterile scissors or peeling apart the glassine at the indicated end. Aseptically transfer each strip from its envelope to a tube
of sterile Spordex Culture Media NA114. Incubate the tubes at 30-35°C (86-95°F) for seven days or for a Customer-validated
reduced incubation time. Examine the media containing the biological indicators during the incubation period. A color change
from red to yellow and/or media becoming turbid indicates microbiological growth. See the instruction card enclosed in the
Spordex Strip box for detailed use directions.
450-100-5513 (01/2020)
STORAGE CONDITIONS
The Spordex Strip BIs should be stored at a temperature of 2-24°C (36-75°F) and a relative humidity of 30-80%. Avoid contact
with, or storage near, sterilants or chemicals; e.g., any oxidizing or reducing agents such as formaldehyde, bleach, ammonia,
etc. Do not use after the expiration date printed on the packaging.
DISPOSAL
Before discarding, treat as appropriate for standard microbiological waste, nonpathogenic species; e.g., steam autoclave at
121°C (250°F) for not less than 30 minutes, incinerate or use other suitable means.
SERVICE
Sales
Service is one of the most important ways to verify consistent quality of the facility's performance and operation. A tailored
service program by STERIS provides effective, trouble-free operations.
Technical
STERIS is pleased to provide a completely staffed and equipped technical service laboratory capable of performing needed
tests and providing both telephone and on-site assistance when needed. More details on how this service can benefit a facility's
particular situation can be provided upon request.
ORDERING INFORMATION
Description Population Quantity Reorder Number

Spordex Strip E5 Biological Indicator 1.0 x 105 to 5.0 x 105 cfu 500 per box NA032
For further information, please contact:
STERIS Corporation
5960 Heisley Road
Mentor, OH 44060-1834 • USA
440-354-2600 • 800-444-9009
www.STERISLifeSciences.com
This data is intended for the exclusive use of STERIS

450-100-5513 ©2014, 2020 TERIS Corporation.All rights reserved. (01/2020) customers, including architects or designers. Reproduction
in whole or in part by others is prohibited.

STERIS Spordex Strips Biological Indicator For Ethylene Oxide and Dry Heat TDS 450 100 5513A

Uploaded by

Copyright:

Available Formats

STERIS Spordex Strips Biological Indicator For Ethylene Oxide and Dry Heat TDS 450 100 5513A

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

STERIS Spordex Strips Biological Indicator For Ethylene Oxide and Dry Heat TDS 450 100 5513A

Uploaded by

Copyright:

Available Formats

SPORDEX® STRIPS

BIOLOGICAL INDICATOR FOR ETHYLENE OXIDE AND DRY HEAT

Packaged in plastic boxes Help to protect the product integrity

Primary packaging: glassine envelope approximately 76 x 25 mm (3 x 1")

Spore carrier: filter paper strip approximately 38 x 6 mm (1-1/2 x 1/4")

Species: Bacillus atrophaeus, NRRL #B4418

Incubation temperature: 30-35°C (86-95°F)

DIRECTIONS FOR USE

Description Population Quantity Reorder Number

For further information, please contact:

This data is intended for the exclusive use of STERIS

You might also like