Scribd
Upload
78 views3 pages

At Export

This document provides information about diagnostic trouble code P1705 related to the throttle position sensor. 1) DTC P1705 indicates a problem with the throttle position sensor circuit where the transmission control module is not receiving the proper accelerator pedal position signals from the engine control module. 2) The diagnostic procedure includes checking the CAN communication lines, verifying the DTC with the transmission control module and engine control module, performing the DTC confirmation procedure, and checking the transmission control module power supply and ground circuit. 3) If the problem persists, the document instructs to check for damage to connectors and harness and replace the control valve with transmission control module if needed.

Uploaded by

Hawkar Suleiman
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
78 views3 pages

At Export

This document provides information about diagnostic trouble code P1705 related to the throttle position sensor. 1) DTC P1705 indicates a problem with the throttle position sensor circuit where the transmission control module is not receiving the proper accelerator pedal position signals from the engine control module. 2) The diagnostic procedure includes checking the CAN communication lines, verifying the DTC with the transmission control module and engine control module, performing the DTC confirmation procedure, and checking the transmission control module power supply and ground circuit. 3) If the problem persists, the document instructs to check for damage to connectors and harness and replace the control valve with transmission control module if needed.

Uploaded by

Hawkar Suleiman
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

DTC P1705 THROTTLE POSITION SENSOR

DTC P1705 THROTTLE POSITION SENSOR PFP:22620


A
Description ECS00COY

Electric throttle control actuator consists of throttle control motor, accelerator pedal position sensor, throttle
position sensor, etc. The actuator sends a signal to the ECM, and ECM sends signals to TCM with CAN com- B
munication.
CONSULT-II Reference Value ECS00COZ

AT
Item name Condition Display value (Approx.)
Released accelerator pedal. 0.0/8
ACCELE POSI
Fully depressed accelerator pedal. 8/8 D

On Board Diagnosis Logic ECS00CP0

● This is not an OBD-II self-diagnostic item. E


● Diagnostic trouble code “P1705 TP SEN/CIRC A/T” with CONSULT-II or 15th judgement flicker without
CONSULT-II is detected when TCM does not receive the proper accelerator pedal position signals (input
by CAN communication) from ECM. F
Possible Cause ECS00CP1

Harness or connectors
(The sensor circuit is open or shorted.) G

DTC Confirmation Procedure ECS00CP2

NOTE: H
If “DTC Confirmation Procedure” has been previously performed, always turn ignition switch “OFF”
and wait at least 10 seconds before performing the next test.
After the repair, perform the following procedure to confirm the malfunction is eliminated. I
WITH CONSULT-II
1. Turn ignition switch “ON”. (Do not start engine.)
2. Select “DATA MONITOR” mode for “A/T” with CONSULT-II. J
3. Start engine and let it idle for 1 second.
4. If DTC is detected, go to AT-126, "Diagnostic Procedure" .
K

BCIA0031E

Revision: September 2006 AT-125 2007 Xterra


DTC P1705 THROTTLE POSITION SENSOR

Diagnostic Procedure ECS00CP3

1. CHECK CAN COMMUNICATION LINE


Perform the self-diagnosis. Refer to AT-90, "SELF-DIAGNOSTIC RESULT MODE" .
Is a malfunction in the CAN communication indicated in the results?
YES >> Check CAN communication line. Refer to AT-98, "DTC U1000 CAN COMMUNICATION LINE" .
NO >> GO TO 2.

2. CHECK DTC WITH TCM


With CONSULT-II
1. Turn ignition switch ON. (Do not start engine.)
2. Select “ECU INPUT SIGNALS” in “DATA MONITOR” mode for
“A/T” with CONSULT-II.
3. Depress accelerator pedal and read out the value of “ACCELE
POSI”.
4. Select “SELF-DIAG RESULTS” mode for “A/T” with CONSULT-
II. Refer to AT-90, "SELF-DIAGNOSTIC RESULT MODE" .
OK or NG
OK >> GO TO 4.
NG >> GO TO 3. PCIA0070E

3. CHECK DTC WITH ECM


With CONSULT-II
1. Turn ignition switch “ON”. (Do not start engine.)
2. Select “SELF-DIAG RESULTS” mode for “ENGINE” with CON-
SULT-II. Refer to AT-88, "CONSULT-II Function (A/T)" .
OK or NG
OK >> GO TO 4.
NG >> Check the DTC detected item. Refer to EC-115, "CON-
SULT-II Function (ENGINE)" .
● If CAN communication line is detected, go to AT-98,
"DTC U1000 CAN COMMUNICATION LINE" .
BCIA0031E

4. CHECK DTC
Perform “DTC Confirmation Procedure”.
● Refer to AT-125, "DTC Confirmation Procedure" .
OK or NG
OK >> INSPECTION END
NG >> GO TO 5.

5. CHECK TCM POWER SUPPLY AND GROUND CIRCUIT


Check TCM power supply and ground circuit. Refer to AT-168, "MAIN POWER SUPPLY AND GROUND CIR-
CUIT" .
OK or NG
OK >> GO TO 6.
NG >> Repair or replace damaged parts.

Revision: September 2006 AT-126 2007 Xterra


DTC P1705 THROTTLE POSITION SENSOR

6. DETECT MALFUNCTIONING ITEM A


Check the following.
● The A/T assembly harness connector pin terminals for damage or loose connection with harness connec-
tor. B
OK or NG
OK >> Replace the control valve with TCM. Refer to AT-228, "Control Valve With TCM and A/T Fluid
Temperature Sensor 2" . AT
NG >> Repair or replace damaged parts.

Revision: September 2006 AT-127 2007 Xterra

You might also like