Tutorial PE104

Tutorial 1
Chapter 1
1. A thin film of liquid flows down an inclined channel. The velocity distribution in the flow is given by
where, h = depth of flow, = angle of inclination of the channel to the horizontal, u = velocity at a depth h below the free surface, = density of liquid, = dynamic viscosity of the fluid. Calculate the shear stress: (a) at the bottom of the channel (b) at mid-depth and (c) at the free surface. The coordinate y is measured from the free surface along its normal
[(a)
, (b)
, (c) 0]
2. Two discs of 250 mm diameter are placed 1.5 mm apart and the gap is filled with an oil. A power of 500 W is required to rotate the upper disc at 500 rpm while keeping the lower one stationary. Determine the viscosity of the oil. [ 0. 71 kg/ms] 3. Eight kilometers below the surface of the ocean the pressure is 100 MPa. Determine the specific weight of sea water at this depth if the specific weight at the surface is 10 kN/m3 and the average bulk modulus of elasticity of water is 2.30 GPa. Neglect the variation of g. [ 10. 44 kN/m3 ] 4. The space between two large flat and parallel walls 20 mm apart is filled with a liquid of absolute viscosity 0.8 Pas. Within this space a thin flat plate 200 mm 200mm is towed at a velocity of 200 mm/s at a distance of 5 mm from one wall. The plate and its movement are parallel to the walls. Assuming a linear velocity distribution between the plate and the walls, determine the force exerted by the liquid on the plate. [1. 71 N] 5. What is the approximate capillary rise of water in contact with air (surface tension 0.073 N/m) in a clean glass tube of 5mm in diameter? [ 5.95]
Tutorial 2
Chapter 2
1. For the system shown in Fig 5.10,determine the air pressure pA which will make the pressure at N one
[3.33 kPa]
fourth of that at M.
Fig 5.10
2. Consider the pipe and manometer system as shown in Fig 5.11. The pipe contains water. Find the value of manometer reading h, and the difference in pressure between A and B if there is no flow. If there is a flow from A towards B and the manometer reading is h = 60 mm, then determine the static pressure difference pA - pB [0, 2.94 kPa; 3.53 kPa]
Fig 5.11
3. Determine the air pressure above the water surface in the tank if a force of 8 kN is required to hold the hinged door in position as shown in Fig 5.12. [10.76 kPa]
Fig 5.12
4. The profile of the inner face of a dam takes the form of a parabola with the equation 18y = x , where y is the height above the base and x is the horizontal distance of the face from the vertical reference line. The water level is 27m above the base. Determine the thrust on the dam (per meter with) due to the water pressure, its inclination to the vertical and the point where the line of action of this force intersects the free
o
[ 5.28 MN/m, 42 33', 30.29 m from face ] water surface
5. A solid uniform cylinder of length 150 mm and diameter 75 mm is to float upright in water. Determine
[ 0.641 kg and 0.663 kg] the limits within which its mass should lie.
6. A long prism, the cross-section of which is an equilateral traingle of side a, floats in water with one side horizontal and submerged to a depth h. Find (a) h/a as a function of the specific gravity, S of the prism. (b) The metacentric height in terms of side a, for small angle of rotation if specific gravity, S=0.8.
7. A metal sphere of volume
, specific gravity
and fully immersed in water is . Calculate the
attached by a flexible wire to a buoy of volume and specific gravity tension T in the wire and volume of the buoy that is submerged. Refer to Fig 5.13.
Tutorial 3
Chapter 3
a steady flow in a rectangular cartesian system is given by
1. The velocity field for
What is the path line of the particle which is at (5, 3, 4) at t = 1s ?
2. Verify whether the following flow fields are rotational. If so, determine the components of rotation about the coordinate axes
(i) (iii)
(ii)
[(i)
; (ii) irrotational; (iii)
3. For a steady two-dimensional incompressible flow through a nozzle, the velocity field is given by where x is the distance along the axis of the nozzle from its inlet plane and L is the length of the nozzle. Find (i) an expression of the acceleration of a particle flowing through the nozzle and (ii) the time required for a fluid particle to travel from the inlet to the exit of the nozzle
[ (i)
, (ii)
4. The velocity field for a steady two-dimensional flow in a cartesian coordinate system is given by , where a and b are constants. Find the equation of stream line passing through the point . Find also the condition for irrotationality of the flow.
5. Show that the velocity field given by represents a rigid body motion.
of a fluid
6. For a flow field is given by . (a) Find stream function that will give these velocity components
, if it vanishes on
(b) Also find the
[ (a)
7. A two-dimensional flow field is given by at point A ( )
(b)
. Find the velocity and acceleration in flow field
Velocity =
Acceleration=

Tutorial PE104

Uploaded by

Copyright:

Available Formats

Tutorial PE104

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Tutorial PE104

Uploaded by

Copyright:

Available Formats

Tutorial 1

[ 5.28 MN/m, 42 33', 30.29 m from face ] water surface

7. A metal sphere of volume

and fully immersed in water is . Calculate the

1. The velocity field for

What is the path line of the particle which is at (5, 3, 4) at t = 1s ?

; (ii) irrotational; (iii)

(b) Also find the

. Find the velocity and acceleration in flow field

You might also like