11 IV April 2023

https://doi.org/10.22214/ijraset.2023.50047
 International Journal for Research in Applied Science & Engineering Technology (IJRASET)
ISSN: 2321-9653; IC Value: 45.98; SJ Impact Factor: 7.538
Volume 11 Issue IV Apr 2023- Available at www.ijraset.com

Design and Analysis of Four Wheel Drive

Electric Vehicle
Sathees T1, Prasanth M2, Sriram M3, Premnath S4, Thirusenthilnathan D5
1
Assistant Professor, Department of Mechanical Engineering, Paavai Engineering College, Namakkal,India
2, 3, 4, 5
UG Student, Department of Mechanical Engineering, Paavai Engineering College, Namakkal, India

Abstract: Due to the increase in the cost of fuels and pollution, alternative to conventional internal combustion engine powered vehicles is
needed. As electric vehicles are environment friendly, they are considered green transportation. In an electric vehicle various components
like motor, battery, controllers are used. While designing an electric vehicle, the first and foremost component to be selected is an electric
motor which replaces the Internal Combustion engines of conventional vehicles. Therefore, electric motor used in an electric vehicle must
produce appropriate power and other characteristics that are required for traction purpose. The important task is to select an appropriate
rating of motor based on the load to be carried. This paper describes the procedure for proper selection of rating of electric motor with an
example of DC motor for an electric car. Vehicle dynamics is considered for selecting the proper electric motor that would provide
required power and torque for traction. To achieve all traction characteristics in compact size, a proper selection of motor rating should be
done based on the load.

I. INTRODUCTION
Electric Vehicles (also known as electric cars or Plug-in electric vehicles) are connected, fun, and practical. They reduce pollution
and are even very cheap to use and maintain when compared to Conventional I.C Engine Vehicles. Using electricity as fuel has a
few merits which are not available in Conventional I.C Engine vehicles. We know that electric motors react quickly and
instantaneously, Electric Vehicles have instant high torque and are quite responsive. They are also digitally connected with the
option to control charging from a smartphone app. Just like a Mobile Phone, you can plug in your EV when you get home and
have it ready for you to use the next morning. By charging often, you may never need to go to a Petrol bunk again! The
infrastructure for electric vehicles charging in India has not been fully developed yet. Few initiatives have been taken to set up
community charging stations, as in the case of Plugin India facilitated charging stations. Electric Vehicles can also reduce the
emissions that contribute to climate change and smog, improving public health and reducing ecological damage.These emissions
can be minimized by Charging your EV on renewable energy such as solar or wind. The above are the few main reasons behind
this project. We know that, in India, 60% of the goods and cargo are transported by road. Electric vehicles on road include Trains,
Buses, Cars, Autos and Bikes. Very few industries like BHEL, Visakhapatnam Steel Plant designed and developed cargo vehicles
for their own use. Our project will be available for a common man to commence Cargo Transportation within the city. Our project
consists of a BLDC motor fitted to a 4-speed Sequentialgearbox which is connected to the rear axle of the vehicle. A Li-ion battery
supplies the electric power to run the BLDC motor through a 60V Controller Hub. This controller hub acts as an operating Centre.
The accelerator is connected to the controller itself. The Li-ion Battery is charged using a 10Amps Charger

A. Electric Vehicle
All-electric vehicles, also referred to as battery electric vehicles (BEVs), have an electric motor instead of an internal combustion
engine. The vehicle uses a large traction battery pack to power the electric motor and must be plugged in to a wall outlet or
charging equipment, also called electric vehicle supply equipment (EVSE). Because it runs on electricity, the vehicle emits no
exhaust from a tailpipe and does not contain the typical liquid fuel components, such as a fuel pump, fuel line, or fuel tank. Learn
more about electric vehicles

B. Problem Definition
The problem definition for a four-wheel drive electric vehicle project will depend on the specific goals and objectives of the
project. However, some common problem areas that could be addressed in such a project include:

© IJRASET: All Rights are Reserved | SJ Impact Factor 7.538 | ISRA Journal Impact Factor 7.894 | 255
 International Journal for Research in Applied Science & Engineering Technology (IJRASET)
ISSN: 2321-9653; IC Value: 45.98; SJ Impact Factor: 7.538
Volume 11 Issue IV Apr 2023- Available at www.ijraset.com

1) Range limitations: Electric vehicles typically have limited driving range on a single charge compared to gasoline-powered
vehicles, which can be a barrier to adoption for some drivers. A four-wheel drive electric vehicle project could focus on
improving battery technology, reducing vehicle weight, or increasing charging infrastructure to address range limitations.
2) Cost: Electric vehicles are often more expensive than their gasoline-powered counterparts, which can make them less
accessible to some consumers. A four-wheel drive electric vehicle project could focus on reducing costs through improved
manufacturing processes, increased production volumes, or innovative financing models.
3) Charging Infrastructure: The availability and accessibility of charging infrastructure is a key factor in the adoption of
electric vehicles. A four-wheel drive electric vehicle project could focus on increasing the number and variety of charging
stations, improving charging speeds, or developing new charging technologies to make EVs more convenient for drivers.

C. Working Of The System

When the throttle is energized which means the potentiometer in the throttle gets input and provides the signal to the controller as
in how much power it is supposed to deliver. There are two potentiometers in the throttle if one fails the other keeps operating. The
controller computes the value of the accelerator from the potentiometers and then delivers power accordingly, from the batteries to
the motor. The motor asses the power from the speed controller for transmitting that power into wheels. If accelerator is pressured
then the controller delivers the battery voltage to the motor with respect to its value after the input from rider. If the accelerator is
depressurized, the controller deliver voltage to the motor with respect to the input.

II. MANUFACTURING PROCESS

Manufacturing processes are the steps through which raw materials are transformed into a final product. The manufacturing
process begins with the creation of the materials from which the design is made. These materials are then modified through
manufacturing processes to become the required part. Manufacturing processes can include treating (such as heat treating or
coating), machining, or reshaping the material. The manufacturing process also includes tests and checks for quality assurance
during or after the manufacturing, and planning the production process prior to manufacturing.

A. Metal Cutting
Metal cutting or machining is the process of by removing unwanted material from a block of metal in the form of chips. Cutting
processes work by causing fracture of the material that is processed. Usually, the portion that is fractured away is in small sized
pieces, called chips. Common cutting processes include sawing, shaping (or planning), broaching, drilling, grinding, turning and
milling. Although the actual machines, tools and processes for cutting look very different from each other, the basic mechanism for
the fracture can be understood by just a simple model called for orthogonal cutting.

III. COMPONENTS OF AN FOUR WHEEL DRIVE ELECTRIC VEHICLE

A. Electric Motor
B. Battery
C. Steering
D. Wheel
E. Bearing
F. Rack And Pinion
G. Spur Gear
H. Battery charger

IV. WORKING PRINCIPLE

A. Working
The vehicle model has totally a steering handle in which is connected to the rack and pinion in front side of the vehicle. The wheel
shaft is connected with arrangement of DC motor. Battery is used to run the vehicle. Battery is connected to the DC motor.The
motor connected to the wheel shaft runs the vehicle. Shock absorber is attached to the front shaft which gives more flexibility to
the vehicle. Switch controls the vehicle within range of the speed. Battery and DC motor are joined to the frame of vehicle rigidly.
No need of cooling device for the vehicle. This vehicle causes no pollution.

© IJRASET: All Rights are Reserved | SJ Impact Factor 7.538 | ISRA Journal Impact Factor 7.894 | 256
 International Journal for Research in Applied Science & Engineering Technology (IJRASET)
ISSN: 2321-9653; IC Value: 45.98; SJ Impact Factor: 7.538
Volume 11 Issue IV Apr 2023- Available at www.ijraset.com

Basically, electric vehicle is necessary for saving fossil fuel. The figure shows the simple construction of electric vehicle. It
consists of battery, motor controller, motor which is connected to the transmission system. Here, battery is the energy source
which is charged by taking electric current from the grid (In Solar power electric vehicle, Battery is charged with the use of solar
pv panel which is attached on the roof of the vehicle). These batteries are rechargeable.
Most electric vehicle uses lead acid battery but in new type of electric cars, use lithium ion batteries because it can store more
energy than lead acid battery in same physical space. The efficiency and life span of battery is far better than other type of
batteries, but it is costlier than lead acid battery. After that controller control the flow of energy from energy source to the motor.
Motor transmit the power to the wheels of the vehicle by the use of transmission system

V. CAD MODEL

Fig.1. 2D Layout Model

Fig.2. 3D CAD Model

VI. CONSTRUCTION OF FOUR WHEEL DRIVE ELECTRIC VEHICLE

A. Electric Motor
An electric motor is an electrical machine.that converts electrical energy into mechanical energy Most electric motors operate
through the interaction between the motor’s magnetic field and electric current in a wire winding to generate force in the form of
torque applied on the motor’s shaft. An electric generator is mechanically identical to an electric motor, but operates with a
reversed flow of power, converting mechanical energy into electrical energy

© IJRASET: All Rights are Reserved | SJ Impact Factor 7.538 | ISRA Journal Impact Factor 7.894 | 257
 International Journal for Research in Applied Science & Engineering Technology (IJRASET)
ISSN: 2321-9653; IC Value: 45.98; SJ Impact Factor: 7.538
Volume 11 Issue IV Apr 2023- Available at www.ijraset.com

B. Motor Contorller
In most of the electric vehicle, Brushless DC motor is used which is better than brushed DC motor, permanent magnet DC motor.
Brushless DC motor does not have brush and commutator, the electric vehicle which uses brushless DC motor has to use motor
controller which helps to control various properties of motor to take sufficient current and voltage applied to motor. When
accelerating pedal is press, this linked variable resistor type controller gives signal to the motor controller to adjust speed as per
our needs. The motor controller has no power when vehicle is at rest position.

C. Battery
Electric vehicle batteries differ from starting, lighting, and ignition (SLI) batteries as they are designed to give power over sustained
periods of time and are deep-cycle batteries Batteries for electric vehicles are characterized by their relatively high power- to-weight
ratio, specific energy and energy density; smaller, lighter batteries are desirable because they reduce the weight of the vehicle and
therefore improve its performance. Compared to liquid fuels, most current battery technologies have much lower specific energy,
and this often impacts the maximum all-electric range of the vehicle

D. Rack And Pinion

A rack and pinion is a pair of gears which convert rotational motion into linear motion. The circular pinion engages teeth on a flat
bar - the rack. Rotational motion applied to the pinion will cause the rack to move to the side, up to the limit of its travel. The pinion
is in mesh with a rack. The circular motion of the pinion is transferred into the linear rack movement.

E. Mechanical Energy
Electric motors are mechanically very simple. Electric motors often achieve 90% energy conversion efficiency over the full range of
speeds and power output and can be precisely controlled. They can also be combined with regenerative braking systems that have
the ability to convert movement energy back into stored electricity. This can be used to reduce the wear on brake systems (and
consequent brake pad dust) and reduce the total energy requirement of a trip. Regenerative braking is especially effective for start-
and-stop city use. They can be finely controlled and provide high torque from rest, unlike internal combustion engines, and do not
need multiple gears to match power curves. This removes the need for gearboxes and torque converters. Electric vehicles provide
quiet and smooth operation and consequently have less noise and vibration than internal combustion engines. While this is a
desirable attribute, it has also evoked concern that the absence of the usual sounds of an approaching vehicle poses a danger to
blind, elderly and very young pedestrians. To mitigate this situation, automakers and individual companies are developing systems
that produce warning sounds when electric vehicles are moving slowly, up to a speed when normal motion and rotation (road,
suspension, electric motor, etc.) noises become audibles

VII. FABRICATION WORK

Fig.3. Fabrication Work

© IJRASET: All Rights are Reserved | SJ Impact Factor 7.538 | ISRA Journal Impact Factor 7.894 | 258
 International Journal for Research in Applied Science & Engineering Technology (IJRASET)
ISSN: 2321-9653; IC Value: 45.98; SJ Impact Factor: 7.538
Volume 11 Issue IV Apr 2023- Available at www.ijraset.com

VIII. CONCLUSION
Four wheel drive electric vehicles (4WD EVs) offer several advantages over their two wheel drive counterparts. Here are a few
conclusions
1) Improved Traction: 4WD EVs have better traction than 2WD EVs, which can be particularly helpful in inclement weather or
off-road situations. With power going to all four wheels, 4WD EVs can distribute torque more evenly and effectively
2) Better Handling: 4WD EVs can provide better handling and stability, especially when cornering or taking turns at high speeds.
The extra grip from the four wheels can help keep the vehicle more stable and prevent it from slipping or sliding.
3) Increased Efficiency: 4WD EVs can be more energy efficient than 2WD EVs, as the four-wheel drive system can distribute
torque more efficiently, reducing energy waste.
Overall, 4WD EVs can be a good choice for drivers who frequently encounter difficult terrain or adverse weather conditions.
However, if you don’t need the extra traction and handling capabilities, a 2WD EV may be a more cost-effective option.

REFERENCES
[1] Ramamoorthy, R., Kanagasabai, V., Kausalya, R., Impact of celebrities’ image on brand, International Journal of Pure and Applied Mathematics, V-116, I-18
Special Issue, PP-251-253, 2017
[2] Husain, Electric and Hybrid Vehicles: Design Fundementals, Routledge: CRC Press Taylor & Francis Group, 2005.
[3] J. Miller, Propulsion systems for hybrid vehicles, IET Power and Energy Series, vol. 45, 2004.
[4] T. Meier, S. Riderknecht, and R. Fietzek, “Electric power train configurations with appropriate transmissions systems,” SAE 2011 World Congress &
Exhibition. Detroit, June 2011.
[5] C. Cheng, A. Mc Gordon, and P. Jennings, “Development of a comprehensive and flexible forward dynamic powertrain simulation tool for various hybrid
electric vehicle architectures,” IMechE Part D: Journal of Automobile Engineering, vol. 226, pp. 385-398, 2012.
[6] F. Bottiglione, S. De Pinto, and G. Mantriota, “Infinitely variable transmissions in neutral gear: torque ratio and power re-circulation,” Mechanism and Machine
Theory, vol. 74, no. 3, pp. 285-298, 2014.
[7] H. Qian et al., “Energy management for four-wheel independent driving vehicle,” IEEE International Conference on Intelligent Robots and Systems. Taiwan,
October 2010.
[8] H. Qian et al., “Energy management for four-wheel independent driving vehicle,” IEEE International Conference on Intelligent Robots and Systems. Taiwan,
October 2010.

© IJRASET: All Rights are Reserved | SJ Impact Factor 7.538 | ISRA Journal Impact Factor 7.894 | 259