G A I N D U S T R I E S

Electric motor actuated pump control valve with built-in check valve and handwheel manual override

B U L L E T I N #1625-M

The

GA Industries CHECKtronic TM Pump Control Valve is... ...THREE VALVES IN ONE!

The CHECKtronic Pump Control Valve is a fail-safe electric motor actuated pump control valve that provides an adjustable, controlled opening and closing speed for minimizing the pressure surges and waterhammer associated with normal pump operation PLUS it has a built-in check feature for reliable valve closure upon power or pump failure, independent of the actuator or its controls. And, its integral handwheel manual actuator permits pump operation even if there is no power to the electric actuator. The CHECKtronic Pump Control Valves electric motor actuator greatly simplifies installation and field wiring by eliminating complicated hydraulic power units and controls associated with oil, water or air cylinder actuated valves. The valve is suitable for use with virtually any fluid, from clean water to raw sewage and, with alternate materials, a wide variety of industrial fluids. Its streamlined wye and elbow design handles solids very well, with 60% LESS headloss than a comparable globe or angle valve, thereby reducing pumping cost. The GA Industries CHECKtronic Pump Control Valve...a unique combination of value, simplicity, versatility and reliability, combined with more than a century of experience in surge control valves.

Why use GA Industries CHECKtronic Pump Control Valves?

Pressure Surges Pressure surges occur in liquid systems whenever the fluid velocity is changed. Sudden changes, such as the starting and especially the stopping of pumps, can produce damaging pressure surges and severe water hammer. These pressure surges propagate through the entire system in a wave-like fashion, producing both abnormally high and low pressure transients that can result in burst pipe and valves, fluid column separation, pipeline collapse, customer complaints, personal injury and potential liability. Engineers have employed many methods to eliminate or at least control such surges, some more complicated than others. Pump Control Valves One proven way to prevent undesirable pressure surges associated with pump operation is to install pump control valves on each pump discharge. In addition to functioning as a check valve to prevent back flow when the pump is off-line, pump control valves operate in concert with the pump motor to impart a controlled, gradual change of fluid velocity during normal pump start-up and shutdown so that damaging surge pressures are prevented. The typical hydraulically operated globe or angle, ball, cone, plug or butterfly valve used as a pump control valve requires hydraulic or pneumatic pressure to open and close the valve. Valve operation is sequenced with the pump motor operation through a series of electro-hydraulic controls. In all cases, the pump control valve must be fail-safe so that it closes upon power outage or pump failure to prevent flow reversal. Fail-safe operation requires a complex system of controls and a reliable source of pressure to close the valve upon power outage or failure of the pump. If the pumped fluid is clean and the pressure reliable, line pressure can be used to operate the valve. If the fluid is sewage, dirty or debris-laden, inadequate, unreliable or otherwise unsuitable for use by the controls, a separate source of hydraulic (water or oil) or pneumatic pressure is needed to operate the valve. This often involves sophisticated oil or water accumulators or compressed air systems to ensure sufficient pressure is available to close the valve under all operating scenarios, including power or pump failure. Electric Motor Actuated Pump Control Valves Electric motor actuated pump control valves are sometimes considered because they dont need complex electro-hydraulic controls, accumulators or compressed air systems. Electric motor actuators are simple, dependable and easy to install and operate. However, typical AC electric motor actuated pump control valves are not fail-safe. Upon power failure they normally hold position and if open, allow backflow unless a separate mechanical check valve is installed in addition to the pump control valve. Although they require AC/DC converters, DC motor actuators can be made relatively fail-safe through expensive and cumbersome battery packs. Overall, electric motor actuated pump control valves are not common because their disadvantages usually outweigh their advantages. The CHECKtronic Pump Control Valve The GA Industries CHECKtronic Pump Control Valve is three valves in one! Its innovative design incorporates a fail-safe check valve into an automatic electric motor actuated, slow opening and slow closing pump control valve, plus provides for emergency manual valve operation. Installation is simplified, complicated controls are eliminated and reliable fail-safe operation is ensured without the need for accumulators, compressed air systems, battery packs or separate check valves. The CHECKtronic Pump Control Valves AC electric motor actuator slowly opens and closes the valve in sequence with the pump motor to control surges associated with normal pump operation. The speed of valve operation is field adjustable to suit the system an important feature not found in many electric motor actuated pump control valves. A simple local or remote pump start dry contact closure initiates a pump start/valve opening sequence and a pump stop turns off the pump only after the valve has closed. If the CHECKtronic Pump Control Valve is open when the power fails, the electric motor actuator holds position, but the spring-assisted StopCheck automatically separates from the actuator and quickly closes to prevent back flow. When power is restored, electrical interlocks prevent pump restart until the actuator resets and is holding the valve closed. The GA Industries CHECKtronic Pump Control Valve is the ultimate in value, simplicity, versatility and reliability and is well suited for a wide range of services from water to raw sewage and many industrial fluids.

How does the GA Industries CHECKtronic Pump Control Valve Work?

Pump Start A pump start energizes the pump motor but the CHECKtronic Pump Control Valves electric motor actuator continues to hold the valve tightly closed against the running pump. After the pump is up to speed and pressure, the electric motor actuator energizes and slowly opens the CHECKtronic Pump Control Valve. The slow opening speed controls how fast the fluid column accelerates to flowing velocity in order to minimize pump start-up surges.

Pump Running Valve Open The valve continues to the open position. The CHECKtronic Pump Control Valves streamlined body produces very low headloss and handles fluids such as sewage or debris-laden water without clogging. The valves electric motor actuator has both a visual position indicator and provisions for electrical indication of open and closed.

Normal Pump Shutdown Upon a normal shutdown command, the CHECKtronic Pump Control Valves electric motor actuator begins closing the valve but the pump motor continues to run. The valves slow closing speed controls how fast the fluid column decelerates in order to minimize column separations and pressure surges. The pump motor deenergizes only after the valve is fully seated and the fluid has been brought to rest.

Power Failure or Pump Failure If the valve is open and there is a loss of power to the pump motor or failure of the pump, the integral spring-assisted stop-check automatically separates from the electric motor actuator and quickly closes to prevent backflow through the pump.

Electric Motor Actuator

Standard Electric Motor Actuator The standard GA Industries CHECKtronic Pump Control Valve is equipped with a heavy duty, open-close, multi-turn, self-locking electric motor actuator. The standard actuator is NEMA 4 rated, 230/460VAC/3Ph/60Hz, thermally protected with 120VAC control circuit, reversing contactors, limit switches, torque switches and manual hand wheel. An integral local control station is provided with a lockable local-off-remote selector switch, push buttons and indicating lights. NOTE: Other voltages, NEMA ratings and options are available, consult factory. Standard Two-Speed Operation For proper control of pressure surges, pump control valves must not only have precise valve operating speeds but also the ability to adjust these speeds to suit field conditions. The GA Industries CHECKtronic Pump Control Valves standard electric motor actuator is equipped with an integral, electronic stepping mode to extend the operating time of any portion of the valves stroke. The start and end of the stepping mode and its on/off time can be independently set to provide the flow cutoff characteristic necessary to control the surges associated with normal pump operation. NOTE: The GA Industries CHECKtronic Pump Control Valve can be actuated by virtually any commercially available electric motor actuator, but the features of our STANDARD actuator may not be available from all manufacturers. Typical Sequence of Operation PUMP START 1. Pump start button depressed (if manual pump start) or dry contacts close (if remote pump start). 2. Pump motor starter energizes. 3. CHECKtronic Pump Control Valve opens as pump reaches full speed. NOTE: On some installations a time delay or pressure switch relay may be needed to delay valve opening until pump has come up to speed and pressure. 4. Limit switch contacts close within CHECKtronic Pump Control Valve actuator as valve opens to interlock pump motor starter circuit. 5. Valve open - pump running.

NORMAL PUMP SHUTDOWN 1. Pump stop button depressed (if manual pump stop or dry contacts disengage (if remote pump start). 2. CHECKtronic Pump Control Valve begins to close while pump motor continues to run. 3. At a point very near the closed position, limit switch contacts open within CHECKtronic Pump Control Valve actuator, deenergizing the pump motor starter. 4. CHECKtronic Pump Control Valve continues to the fully seated position as pump coasts to a stop. 5. Valve closed - pump stopped.

115 VAC 1 PHASE CONTROL VOLTAGE

COMPONENTS NOT FURNISHED BY GA INDUSTRIES: START - MOMENTARY PUSHBUTTON OR MOMENTARY CONTACT CLOSURE TO INITIATE START SEQUENCE STOP - MOMENTARY PUSHBUTTON OR MOMENTARY CONTACT CLOSURE TO INITIATE STOP SEQUENCE

CR1
START CR1 LS1* CR3 LS2*

MSCR - MOTOR STARTER CONTROL RELAY CR1, CR2, CR3 - CONTACT RELAYS TDR1 - TIME DELAY RELAY (ON-DELAY TYPE: DELAY TIMER STARTS WHEN ENERGIZED, CONTACTS TRANSFER AFTER DELAY PERIOD, DE-ENERGIZE TO RESET) TDR2, TDR3 - TIME DELAY RELAY (INTERVAL-DELAY TYPE: CONTACTS TRANSFER WHEN ENERGIZED, DELAY TIMER STARTS WHEN ENERGIZED, CONTACTS RETURN AFTER DELAY PERIOD, DE-ENERGIZE TO RESET)

MSCR
CR1

NOTE: BASIC CONTROL SCHEMATIC SHOWN PROVIDES FOR NORMAL PUMP START AND NORMAL PUMP STOP SEQUENCE ONLY. STATUS INDICATION, EMERGENCY LOCK-OUTS, EMERGENCY INDICATION, AND/OR PUMP ALTERNATING CONTROL(S) ARE NOT INCLUDED IN THE BASIC CONTROL SCHEMATIC. THESE ITEMS MAY BE ADDED TO THE CONTROL SCHEMATIC AS REQUIRED BY THE DESIGN ENGINEER.

TDR1
CR1

TDR2
TDR1

CR2
STOP

OPEN CHECKTRONIC ELECTRIC MOTOR ACTUATOR TDR2 CR2 TDR3

CONTROL BOX - REMOTE CONTROL INPUTS

CR3
CR2 CR3 CR1

CLOSE DIAGRAM FOR ADDITIONAL WIRING CONNECTIONS LS1* - LIMIT SWITCH IN MOTOR ACTUATOR CONTACTS CLOSE WHEN VALVE CLOSED LS2* - LIMIT SWITCH IN MOTOR ACTUATOR CONTACTS OPEN WHEN VALVE CLOSED

SEE ELECTRIC MOTOR ACTUATOR WIRING

TDR3

115 VAC

Parts List Wye Body Pattern

FLOW

ITEM 1 2 3 4 5 6 7 8 10 12

DESCRIPTION Body Cover Disc Body Seat Disc Seat Ring Seat Follower Seat Follower Screws Stem Rod Wiper Bushing

ITEM 13 14 15 17 18 19 28 29 30 31

DESCRIPTION Bushing Seal Gland Gland Seal Stem Seal Cover Bolts Cover Seal Stem Lock Screw Stem Lock Washer Body Plug Spring Seat

ITEM 32 33 34 35 36 37 38 39 40 41 42

DESCRIPTION Spring Seat Washer Spring Seat Nut Spring Actuator Mounting Bracket Actuator Threaded Stem Actuator Threaded Stem Key Actuator Threaded Stem Key Bolts Actuator Adaptor Adaptor Bolts Actuator Bolts Electric Motor Actuator

Parts List Elbow Body Pattern

FLOW

ITEM 1 2 3 4 5 6 7 8 10 12

DESCRIPTION Body Cover Disc Body Seat Disc Seat Ring Seat Follower Seat Follower Screws Stem Rod Wiper Bushing

ITEM 13 14 15 17 18 19 28 29 30 31

DESCRIPTION Bushing Seal Gland Gland Seal Stem Seal Cover Bolts Cover Seal Stem Lock Screw Stem Lock Washer Body Plug Spring Seat

ITEM 32 33 34 35 36 37 38 39 40 41 42

DESCRIPTION Spring Seat Washer Spring Seat Nut Spring Actuator Mounting Bracket Actuator Threaded Stem Actuator Threaded Stem Key Actuator Threaded Stem Key Bolts Actuator Adaptor Adaptor Bolts Actuator Bolts Electric Motor Actuator

MATERIALS OF CONSTRUCTION
PART
Body, Cover

MATERIAL
Cast Iron (Standard) Ductile Iron (Optional) Cast Steel (Optional) Cast Stainless Steel (Optional) Ductile Iron (Standard) Cast Stainless Steel (Optional) Cast Steel Stainless Steel Stainless Steel Synthetic Polymer

SPECIFICATION

ASTM A126 Class B ASTM A536 ASTM A216 Gr. WCB ASTM A351 Disc ASTM A536 Type 18-8 ASTM A216 Gr. WCB Body Seat, Seat Follower Type 316 Stem Type 303 Disc Seat Ring Ultra High Molecular Weight Polyethylene (UHMWPE) O-Rings & Gaskets Rubber/Composition Buna-N/Fiber (Other Materials Available) Gland, Bushing Brass C36000 Internal Wetted Fasteners Stainless Steel Type 18-8 Actuator Bracket & Adaptor Steel ASTM A36 Spring Steel ASTM A229 External Fasteners Steel ASTM A307 Threaded Stem Stainless Steel Type 18-8 Note: We reserve the right to substitute materials which in our opinion are of equal or superior quality.

PRESSURE RATINGS
Cast Iron Body, Class 125 Flanges Cast Iron Body, Class 250 Flanges Ductile Iron Body, Class 150 Flanges Ductile Iron Body, Class 300 Flanges 200 150 400 300 250 500 PSI PSI PSI PSI PSI PSI (3 to 12 Size) (14 to 24 Size) (3 to 12 Size) (14 to 24 Size) (3 to 24 Size) (3 to 24 Size)

WARRANTY
This GA Industries product is made of the finest available materials and every possible precaution has been taken to assure premium workmanship consistent with established quality procedures. Valves or parts proven faulty due to defective materials or poor workmanship will be replaced free of charge, FOB our factory, upon presentation of such proof. This warranty shall not cover the cost of installation and is valid for one year from date of shipment. Dimensions and specifications are subject to change without notice.

NOTE: 1. Standard flanges conform to ANSI standards. BS, DIN, ISO and other flanges are available, consult factory for availability and pressure ratings. 2. Higher pressure ratings available with steel or stainless steel body. 3. Valve maximum working pressure (MWP) may be less than pressure rating due to actuator.

APPROXIMATE SHIPPING WEIGHTS

SIZE (IN) (MM) 3 75 4 100 6 150 8 200 10 250 12 300 14 350 16 400 18 450 20 500 24 600 WEIGHT (LBS) (KG)

275 125

300 136

525 238

675 306

870 394

1400 635

2400 1088

2750 1247

3150 1428

3450 1564

6800 3082

Dimensional Data Wye Body

B
(SEE NOTE 3)

FLOW

C
(SEE NOTE 3)

3 4 6 8 10 12 14 16 18 20 24 30

A inches 12 13 18 241/2 26 31 33 36 40 40 48 60

B inches 29 301/2 331/2 37 401/2 45 46 521/2 60 61 64 85

C inches 151/2 141/2 13 101/2 13 121/2 111/2 131/2 151/2 151/2 17 22

VALVE BODY WIDTH

inches 63/4 8 111/2 15 18 195/8 21 25 28 28 33 45

Elbow Body
B
(SEE NOTE 3)

FLOW

C
(SEE NOTE 4)

3 4 6 8 10 12 14 16 18 20 24 30

A inches 73/4 9 111/2 14 161/2 19 211/2 24 261/2 29 34 411/2

B inches 32 33 34 35 36 371/2 41 50 52 54 58 70

C inches 5 6 7 8 11 13 16 17 21 23 24 28

VALVE BODY WIDTH

inches 21/2 3 31/2 4 51/2 61/2 8 81/2 111/2 13 12 14

NOTE: 1. Standard flanges per ANSI B16.1. BS, DIN, ISO and other flanges are available. 2. A dimension on valves with raised face flanges does not include the length of the raised face. 3. Dimension may vary per operator selection. For accurate dimension, consult factory. 4. Actuator may extend beyond valve body width and can be rotated in 90 0 increments. 5. Dimensions shown are for estimating purposes and are not guaranteed. Certified drawings are available when requested with order. 6. Divide inches by 0.039 to obtain millimeters.

Reduce Headloss and Save Pumping Costs

The GA Industries CHECKtronic Pump Control Valves full-ported, streamlined long radius elbow pattern and wye body style have 60% LESS headloss than traditional angle and globe body valves.

HEADLOSS VS FLOW FOR LONG RADIUS ELBOW BODY VALVE

100 50 40 LOSS OF HEAD IN FEET OF WATER LOSS OF HEAD IN FEET OF WATER 30 1,000 10,000 100,000 50

20 VALVE SIZE 10 9 8 7 6 5 4 3 3" 4" 6" 8" 10" 12" 14" 16" 18" 20" 24" 10

1 100 2 3 4 5 6 7 8 9 1,000 2 3 4 5 6 7 8 9 10,000 2 3 4 FLOW IN U.S. GALLONS PER MINUTE

1 5 6 7 8 9 100,000

HEADLOSS VS FLOW FOR WYE BODY VALVE

100 50 40 30 1,000 10,000 100,000 50

20 VALVE SIZE 10 9 8 7 6 5 4 3 3" 4" 6" 8" 10" 12" 14" 16" 18" 20" 24" 10

1 100 2 3 4 5 6 7 8 9 1,000 2 3 4 5 6 7 8 9 10,000 2 3 4 FLOW IN U.S. GALLONS PER MINUTE

1 5 6 7 8 9 100,000

SPECIFICATION
CONSTRUCTION
The valve body shall be of the [in-line wye][long radius elbow] pattern of [cast iron conforming to ASTMA126 Class B][ductile iron conforming to ASTM A536 Grade 65-45-12] with integral flanges faced and drilled to ANSI B16.1 [Class 125][Class 250]. The valve shall be inherently self-cleaning with a net flow area of no less than the area of its nominal pipe size. The body shall have a replaceable 316 stainless steel seat and a seat inspection port. The valve disc shall be ductile iron with a renewable resilient seat ring of ultra-high molecular weight polyethylene (UHMWPE) or other suitable resilient material, retained by a stainless steel follower ring with stainless steel screws. The valve stem shall be stainless steel and guided by a long bronze bearing in the valve cover and sealed where it passes through the cover by means of a replaceable pressure actuated seal. The valve disc shall be designed to close quickly upon flow reversal, independent of the actuator, to prevent backflow. A spring shall be provided to assist valve closure. The electric motor actuator shall be multi-turn, non-modulating [230/460VAC, 60 Hertz, 3 Phase NEMA 4] [_________VAC, _____Hertz, _____Phase, NEMA____] meeting AWWA C540 with integral limit switches, torque switches, visual position indicator and manual handwheel. Controls shall include reversing starter, control transformer, local-off-remote selector, indicating lights and open/close push buttons. The actuator shall provide a minimum valve operating time of [ ] seconds with an integral stepping mode to extend the operating time over any portion of the valve stroke. The start/end and the on/off pulse time shall be field adjustable.

FUNCTION
The Pump Control Valve with Electric Motor Actuator shall function to minimize surges associated with the normal starting and stopping of pumps. The valve shall slowly open after the pump has come up to speed and pressure at pump start. A normal pump shutdown shall be initiated by the valve slowly closing against the running pump, turning off the pump only after the valve has completely closed. The valve shall quickly close independently of the actuator upon flow reversal resulting from power outage, pump or pump motor failure or other sudden stoppages of pumping.

MANUFACTURER
The valve shall be the Series 1600-M CHECKtronic Pump Control Valve as manufactured by GA Industries, Inc., Cranberry Township, PA USA NOTE: Specifier to select [bracketed] options. Product improvement is always evident at GA Industries, Inc. Specifications and design may change without notice.

I N F O R M AT I O N N E E D E D W H E N O R D E R I N G
1. 2. 3. 4. 5. Size and Quantity Body Style Body Material and Flange Class Installation Orientation Type of Fluid 6. 7. 8. 9. 10. Pump Shut Off Head Minimum Static Head at Valve Outlet Pump Discharge Head Actuator Electrical Characteristics Operating Speed

10

Design Features
PUMP CONTROL Field adjustable slow opening and closing PUMP CONTROL controls normal pump start-up and shutdown surges ELECTRIC ACTUATOR PUMP CONTROL Simple, cost ELECTRIC ACTUATOR ACTUATOR PUMP CONTROL actuator eliminates CONTROL effective electric motor PUMP CONTROL CHECK PUMP hydraulic power units, solenoid valves complicated ELECTRIC ACTUATOR CHECK actuators and cylinder ELECTRICOVERDRIVE ELECTRIC ACTUATOR MANUAL ACTUATOR ELECTRIC ACTUATOR CHECK OVERDRIVE MANUAL Spring-assisted StopCheck reliably closes independent of actuator to prevent back-flow CHECK CHECK or failure VERSATILE CHECK pump upon power MANUAL OVERDRIVE VERSATILE MANUAL OVERDRIVE Permits emergency MANUAL OVERDRIVE OVERRIDE LOW operation with HEADLOSS inoperative MANUAL OVERDRIVE actuator pump VERSATILE LOW HEADLOSS VERSATILE VERSATILE 3 (80mm) to 24 (600mm) VERSATILE TRIM VERSATILE in wye LOW HEADLOSS elbow body TRIM or long radius LOW HEADLOSS LOW HEADLOSS LOW HEADLOSS 60% LESS than typical globe or angle valve HEADLOSS TRIM TRIM TRIM Standard 316 stainless steel replaceable body seat and ultra-high molecular weight TRIM
polyethylene (UHMWPE) renewable disc seat for drop tight shutoff

9025 MARSHALL ROAD CRANBERRY TWP., PA 16066-3696 USA PHONE: (724) 776-1020 FAX: (724) 776-1254 WEB SITE: www.gaindustries.com E-MAIL: [email protected]
2002 GA Industries, Inc. CHECKtronic Pump Control Valve Patent Pending
COMM 0607-1500