7 471

Illustrative example: LMS14

Boiler Management Unit LMS14...

(BMU) LMS15...
LMS1x are digital Boiler Management Units (BMUs) for use in gas-fired appliances
equipped with premixing burners.

The LMS1x and this Data Sheet are intended for use by OEMs which integrate the
BMUs in their products.

Notes

Please note!
All the safety, warning, and technical notes given in the user manual for the
LMS1x (U7471/U7472) also apply to this document in full. Failure to observe
this information poses a risk of damaging the safety functions and the risk of
electric shock.

CC1N7471en Smart Infrastructure

19.11.2021
Use

LMS1x are digital boiler management units (BMUs) for use with gas-fired
appliances equipped with premix burners. They are used for startup, control and
supervision of premix burners with capacities from <10 kW to 1 MW in intermittent
operation with direct ignition of the main flame. The OEM must make certain that
the LMS1x are suited for the application in question.

The LMS1x provide all supervisory and control functions required for burner
operation, space heating and DHW heating. They also offer modular system
extensions in the form of integrated communication interfaces. Output modulation
is performed via a PWM-controlled fan with pneumatic/electrical gas-air ratio
control.

With the LMS14, load modulation is performed via a PWM-controlled fan with
pneumatic gas-air ratio control.

With the LMS15, load modulation is performed by a PWM-controlled fan via an

electronic ratio control regulated by the Sitherm Pro combustion optimizer.

2/30

Smart Infrastructure CC1N7471en

19.11.2021
Supplementary documentation

Documentation
LMS14

LMS15
Type (ASN) Description
no.

CC1E7471 *)
LMS14 Boiler Management Unit CC1Q7471
CC1U7471
CC1E7471 *)
Boiler Management Unit CC1Q7471
LMS15
Sitherm Pro CC1U7471
CC1U7472

Product range Product range overview Albatros² CE1Q2359

System Albatros2 system CE1P2359_08

Subschema Albatros2 Hydraulic subschema and extra functions CE1P2359_10

ACS420 Software for OCI430 ---

ACS432 Parameter stick manager CC1J7474
ACS434 Setup assistant CC1J7475
ACS435 Setup-Manager CC1J7471
Remote supervision software / parameterization software for
ACS700 Software CD
OCI700
Remote supervision software/parameterization software for
ACS790 Software CD
OCI700

AGU2.550 Extension ClipIn for LMS1x CC1N7492

AGU2.551 Extension ClipIn for PWM (DC 0...10 V) CC1N7493
AGU2.560 Parameter stick for LMS1x, can be read out CC1U7471
AGU2.561 Parameter stick for LMS1x, writable CC1U7471
AGU2.563 Parameter stick for direct programming of the LMS1x CC1U7471
AGU2.564 Parameter stick for spare part programming of the LMS1x CC1U7471
AGU3.6 Gas/air mixer CC1N7211
AGU3.7 Gas/air mixer CC1N7214

AVS13.399 Wireless outside sensor CE1U2354

AVS14.390 Wireless repeater CE1U2354
AVS37.294 Operating unit (clear text) CE1U2353
AVS37.390 Operating unit (basic) CE1U2358
AVS71.390 Wireless module CE1U2354
AVS71.393 Wireless module BSB CE1U2358
UI400 room unit and operating unit
AVS74 When connecting the UI400 to the LMS14, various restrictions CE1U2348
may apply depending on the software version.

3/30

Smart Infrastructure CC1N7471en

19.11.2021
 Documentation
LMS14

LMS15
Type (ASN) Description
no.

AVS75.390 Extension module CE1U2353

AVS75.391 Extension module CE1U2354

OCI345.06/101 LPB ClipIn CC1U2355_043

OCI351.01/101 Modbus ClipIn CE1U2355_043
OCI430 Interface module for PC-LMS1x connection CC1N7635
OCI431 Programming station for LMS1x boiler management unit CC1U7669
OCI700 Service tool CC1E5655 *)

QAA55.110 Room unit basic CE1U2353

UI400 room unit and operating unit
QAA74 When connecting the UI400 to the LMS14, various restrictions CE1U2348
may apply depending on the software version.
QAA75.610 Room unit wire CE1U2353
QAA75.611 Room unit wire with backlight CE1U2353
QAA78.610 Room unit wireless CE1U2353

QAC34/101 Outside sensor NTC 1 k CC1Q1701

QAD36/101 Contact temperature sensor NTC 10 k CC1Q1808

QAZ36.522/109 Immersion temperature sensor NTC 10 k CC1Q1843

QAZ36.526/109 Immersion temperature sensor NTC 10 k CC1Q1843

Ignition module, combined with connection line for LMS14,

TQG42 CC1N7630
suitable for VGUSmart gas valves

VGE5xS Combination gas valves CC1N7669

VGU7xS Combination gas valves CC1N7668
VGU8xS Combination gas valves CC1N7668

4/30

Smart Infrastructure CC1N7471en

19.11.2021
Standards and certificates
Applied directives:
 Low-voltage directive 2014/35/EC
 Gas Appliances Regulation (EU) (EU) 2016/426
 Electromagnetic compatibility EMC (immunity) *) 2014/30/EC
*) The compliance with EMC emission requirements must be checked after the Boiler Management Unit
is installed in equipment

Compliance with the regulations of the applied directives is verified by the adherence to
the following standards / regulations:
 Automatic burner control systems for burners and DIN EN 298
appliances burning gaseous or liquid fuels
 Only LMS15: EN 12067-2
Gas/air ratio controls for gas burners and gas burning
appliances
Part 2: Electronic types
 Safety and control devices for gas burners and gas DIN EN 13611
burning appliances - General requirements
 Control functions in electronic systems for gas burners DIN EN 14459
and gas burning appliances
Methods for classification and assessment;
 Automatic electrical controls for household and similar use DIN EN 60730-2-5
Part 2-5:
Particular requirements for automatic electrical burner
control systems

The relevant valid edition of the standards can be found in the declaration of
conformity!

EAC Conformity mark (Eurasian Conformity mark)

ISO 9001:2015
ISO 14001:2015
OHSAS 18001:2007

China RoHS
Hazardous substances table:
http://www.siemens.com/download?A6V10883536

LMS14  
LMS15 --- 

Disposal notes

The LMS1x contains electrical and electronic components and must not be disposed of
together with domestic waste. Local and currently valid legislation must be complied
with.

5/30

Smart Infrastructure CC1N7471en

19.11.2021
Life cycle

The LMS1x has a designed lifetime* of 250,000 burner startup cycles which, under
normal operating conditions in heating mode, corresponds to approx. 10 years of
service (starting from the date of manufacture on the type label).
This is based on the endurance tests specified in the standard EN 298. A summary of
the conditions has been published by the European Control Manufacturers Association
(www.afecor.org).

The designed lifetime is based on use of the LMS1x according to the manufacturer’s
Data Sheet and User Manual. After reaching the designed lifetime in terms of the
number of burner startup cycles, or the respective time of usage, the LMS1x is to be
replaced by authorized personnel.

* The designed lifetime is not the warranty time specified in the Terms of Delivery.

Type summary

Boiler management system

LMS14
 Printed circuit board design
 Without combustion optimization

LMS15
 Printed circuit board design
 With combustion optimization

 Note
Details on the accessories and required system components can found in the LMS1x
product range overview Q7471.

6/30

Smart Infrastructure CC1N7471en

19.11.2021
Technical Data LMS14

Basic unit
General Mains voltage (rated voltage)
 LMS14.815B109 only AC 120 V +10%/-15%
 All other LMS14 types AC 230 V +10%/-15%
Mains frequency
 LMS14.815B109 only 60 Hz to EN 298
 All other LMS14 types 50 Hz to EN 298
Power consumption
 Operation Max. 14 W
 Power pack Max. 14 W
Rated surge voltage category III (EN 60664-1:2008)
Degree of protection IP00
IP40 according to EN 60529:1991 +
A1:2000 + A2:2013 (to be ensured when
fitted inside the boiler)
Safety class LMS14 designed for use in equipment of
protection class I according to
EN 60730-1:2017
Degree of pollution 2
Software classes As per EN 60730-2:2015 + A1:2019
 Controller part Class A
 LMS14 Class C
Dimensions (L x W x D) 230 x 150 x 30 mm
Weight Approx. 0.254 kg
Unit fuse 2 x T6.3H250 internal

Caution!
Risk of damage to the fuel valve switching contacts!
If the internal mains fuse (FB01/FB02) is blown due to overload or short-circuit at
the fuel valve connections, the LMS14 must be replaced.

Mounting position Optional

Caution!
When making 100% inspections as per EN 60335-1:2012 + A1:2019 + A2:2019 +
A11:2014 + A13:2017 + A14:2019 Addendum A, only AC voltage may be applied.
If DC voltage tests are conducted, the LMS14 can get damaged.

7/30

Smart Infrastructure CC1N7471en

19.11.2021
Technical Data LMS14 (cont'd)

Environmental
conditions Warning!
Condensation, formation of ice and ingress of water are not permitted!
Failure to observe this information poses a risk of damaging the safety
functions and a risk of electric shock.

Climatic conditions Storage

Temperature range -20...60 °C
Humidity <90% r.h. (noncondensing)
Transport
Temperature range -20...60 °C
Humidity <90% r.h. (noncondensing)
Operation
Temperature range 0...60 °C
Humidity <85% r.h. (noncondensing)
Installation altitude Max. 2,000 m above sea level

8/30

Smart Infrastructure CC1N7471en

19.11.2021
Technical Data LMS14 (cont'd)
Electrical connections
Mains voltage connections Total current all mains components connected to LMS14 and clipins
 LMS14.815B109 only 5 A (at UMains = AC 120 V; Ta = 25 °C)
 All other LMS14 types 5 A (at UMains = AC 230 V; Ta = 25 °C)

Attention!
Fuse protection!
The following connecting terminals are protected by the unit fuse as per the
chapter titled Technical data - General data.

The cross sections of the connection lines must be designed according to the unit
fuses.

Mains extension AUX1/AUX2

 Voltage
LMS14.815B109 only AC 120 V
All other LMS14 types AC 230 V
 Current Depending on the current consumption of
the programmable mains voltage outputs
QX1 to QX3, fuel valve, external ignition
module and clip-ins used
QX1
 Voltage
LMS14.815B109 only AC 120 V +10%/-15%
All other LMS14 types AC 230 V +10%/-15%
 Current 5 mA…1 A, cos >0.8
 Cable length 120 m
QX2
 Voltage
LMS14.815B109 only AC 120 V +10%/-15%
All other LMS14 types AC 230 V +10%/-15%
 Current 5 mA…1 A, cos >0.8
 Cable length 120 m
QX3
 Voltage
LMS14.815B109 only AC 120 V +10%/-15%
All other LMS14 types AC 230 V +10%/-15%
 Current 5 mA…1 A, cos >0.8
 Cable length 120 m
Flame supervision/ionization probe
 Switching thresholds Min. 0.52 µA (required DC current)
 Current
Nur LMS14.815B109 Typically 4 µA, max. 8.2 µA
All other LMS14 types Typically 4 µA, max. 12.8 µA
 Response time in the event of loss of 1 s
flame
 Physical contact The ionization probe and its connections
must be located such that adequate
protection against direct or indirect
contact with active parts is ensured in
every unfavorable position allowed under
correct usage conditions
 Cable length for flame detector 1 m

Please note!
Interchangeability of L/N conductors!
L-conductors and N-conductors are not interchangeable across all LMS14
variants!

9/30

Smart Infrastructure CC1N7471en

19.11.2021
Technical Data LMS14 (cont'd)

Safety limit thermostat

 Voltage
LMS14.815B109 only AC 120 V
All other LMS14 types AC 230 V
 Current 5 mA...1 A, cos >0.6
Carrying power to the fuel valve and
ignition
 Cable length 1 m
Fuel valve
 AC output
LMS14.815B109 only AC 120 V +10%/-15%
Valve must still open at AC 91 V
All other LMS14 types AC 230 V +10%/-15%
Valve must still open at AC 175 V
 Current 5 mA…0.5 A, cos >0.6

Note!
 A fuel valve with rectifier may be connected to the fuel valve output only if
 approved by Siemens!
 In this case, additional protective measures inside the LMS14 must be taken
(optional components)

RAC output (optional components)

LMS14.815B109 only RAC 120 V +10%/-15% 100 Hz
Valve must still open at RAC 91 V
All other LMS14 types RAC 230 V +10%/-15% 100 Hz
Valve must still open at RAC 175 V
 Output Max. 20 W, cos >0.9
General data on connection of fuel valve
 Cable length Max. 1 m for AC/RAC
Max. 3 m if cable is routed separately
(to avoid capacitive coupling)
 Capacitive extra circuit or surge voltage Not permitted
limiting protective elements
External ignition module
 Voltage
LMS14.815B109 only AC 120 V +10%/-15%
All other LMS14 types AC 230 V +10%/-15%
 Current
LMS14.815B109 only 5 mA…0.5 A, cos >0.6
Full ignition required at AC 91 V
All other LMS14 types 5 mA…0.5 A, cos >0.6
Full ignition required at AC 175 V
 Cable length Max. 1 m
Max. 3 m if cable is routed separately
(to avoid capacitive coupling)
 Starting current Max 1 A
In terms of switching performance, every external ignition module used must be
approved by Siemens!
Fan control For fans with mains-powered DC motor.
Refer to separate Siemens specification
Spezifikation_LMU5x_TrafoGebläse_de_V
X.Y.doc (mandatory)

10/30

Smart Infrastructure CC1N7471en

19.11.2021
Technical Data LMS14 (cont'd)
Extra-low voltage
connections (PELV)
Supply voltage outputs,
general data
Warning!
For functional reasons, the LMS14 extra-low voltage circuits are connected to
the protective earth via X17. Therefore, they are classed as PELV circuits.

+5 V
 Output voltage LMS14 DC 5 V ±5%
 Short-circuit current (current Imax. 1 A
limitation)
+12 V
 Output voltage LMS14 DC 12 V ±5%
 Short-circuit current (current Imax. 0.8 A
limitation)
+15 V
 Output voltage LMS14 DC 15 V ±5%
 Short-circuit current (current Imax. 1.5 A
limitation)
+24 V
 Output voltage LMS14 DC 24 V ±5%
 Short-circuit current (current Imax. 1.1 A
limitation)

Inputs B2 Boiler sensor B2 NTC 10 k

 Continuous temperature Max. 100 °C
 Short-time temperature Max. 125 °C
 Sensor tolerance ±2 K
 Cable length 3 m
 Aging ±3%
  20 s
 Other requirements Conformity to DIN EN 60730-2-9 and
DIN EN 14459:2007 Annex K

Inputs B7 / BX4 Return sensor (B7)/multifunctional sensor BX4 (X4)

 Resistance value
- Return sensor (B7) NTC 10 k
Refer to boiler sensor B2
- Multifunctional sensor (BX4) NTC 10 k (QAZ36, QAD36)
NTC 20 k (flue gas sensor)
Pt1000 optional for collector sensor and
flue gas sensor)
 Cable length 3 m

Note!
 Sensor input BX4 has a fixed assignment to sensor B7. The reading of sensor B7 is
safety relevant.

11/30

Smart Infrastructure CC1N7471en

19.11.2021
Technical Data LMS14 (cont'd)

Inputs B3 / B38 DHW sensor B3/B38 (X5)

 Resistance value NTC 10 k
 Cable length 10 m (when connecting a thermostat to
the input for the DHW sensor, high-quality
thermostat contact material is required
(e.g. gold-plated contacts), since signal
voltage at this input is DC 5 V)

Inputs BX1 / BX2 / BX3 Sensor inputs BX1…BX3 (X5)

 Resistance value NTC 10 k (QAZ36, QAD36)
NTC 20 k (flue gas sensor)
Pt1000 (optional for collector sensor and
flue gas sensor)
 Cable length 120 m
Observe cross-sectional area of wires!
(Refer to chapter Cross-sectional area
sensors)

Inputs B9 Outside temperature sensor B9 (X5)

 Resistance value NTC 1 k
Refer to specification QAC34
 Cable length 120 m
Observe cross-sectional area of wires!
(Refer to chapter Cross-sectional area
sensors)

Inputs H1 Multifunctional input/pressure sensor (X6)

 Output voltage LMS14 DC 15 V ±5%
DC 5 V ±5%
 Current Imax. 10 mA each input
 Input voltage LMS14 DC 10 V
 Analog input Safety extra low-voltage
- Operating range DC 0…10 V
- Input resistance >100 k
 Digital input
- Safety extra low-voltage for potential-free low-voltage contacts
Voltage with contact open DC 15 V
Voltage with contact closed DC 1.5 mA
 Cable length 10 m

Inputs H3 Multifunctional input/pressure sensor (X4)

 Output voltage LMS14 DC 15 V ±5%
DC 5 V ±5%
 Current Imax. 10 mA
 Input voltage LMS14 DC 10 V
 Analog input Safety extra low-voltage
- Operating range DC 0…10 V
- Input resistance >100 k
 Digital input
 Safety extra low-voltage for potential-free low-voltage contacts
Voltage with open contact DC 15 V
Voltage with closed contact DC 1.5 mA
 Cable length 10 m

12/30

Smart Infrastructure CC1N7471en

19.11.2021
Technical Data LMS14 (cont'd)

Inputs H4 Multifunctional input/pressure sensor (X6)

 Output voltage LMS14 DC 15 V ±5%
DC 5 V ±5%
 Current Imax. 10 mA
 Input frequency 0/1…1 kHz
 Digital input
 Safety extra low-voltage for potential-free low-voltage contacts
Voltage with contact open DC 5 V
Voltage with contact closed DC 2 mA
Frequency input
 Duty cycle 10…90%
 ton ; toff >300 µs
 Resolution 0.1 Hz at 1…1 kHz
 Rise/drop-out time 20 µs
Cable length 10 m

Inputs H5 Multifunctional input/room thermostat (X6)

 Voltage DC 5 V
 Digital input
 Safety extra low-voltage for potentialfree low-voltage contacts
Voltage with contact open DC 5 V
Voltage with contact closed DC 2 mA
 Cable length 120 m
Observe cross-sectional area of wires!
(Refer to chapter Cross-sectional area
sensors)

Inputs H6 Multifunctional input/gas pressure switch (X5)

 Digital input
 Safety extra low-voltage for potential-free low-voltage contacts
Voltage with contact open DC 5 V
Voltage with contact closed DC 2 mA
 Cable length 120 m
Observe cross-sectional area of wires!
(Refer to chapter Cross-sectional area
sensors)

Inputs H7 Multifunctional input/air pressure switch (X4)

 Digital input
 Safety extra low-voltage for potential-free low-voltage contacts
Voltage with contact open DC 5 V
Current with contact closed DC 2 mA
 Cable length 10 m

Input reset (EK) Reset button (X4/X30)

 Digital input Active upon short-circuit after safety
extra-low voltage GND
 Safety extra low voltage for potential-free low-voltage contacts
Voltage with contact open DC 5 V
Current with contact closed DC 0.5 mA
 Line length 1 m

13/30

Smart Infrastructure CC1N7471en

19.11.2021
Technical Data LMS14 (cont'd)

PWM fan/Hall
connection facility
Warning!
Mandatory requirement: Observe separate Siemens specification
Spezifikation_LMU5x_TrafoGebläse_de_VX.Y.doc

PWM fan/Hall connection facility (X8)

 PWM output
- Safety extra low voltage
Voltage with output open DC 24 V
Current Max. DC 15 mA
- Line length 3 m
- Basic control frequency 800…4800 Hz (default 4096 Hz)
(adjustable)
 Hall input, fan speed
Voltage with output open <DC 1 V
Input resistance 37 kOhm
Frequency range 0…900 Hz
Duty cycle 30…70 %

PWM pump connection PWM pump connection (X15)

P1  PWM output As per interface definition of Grundfos for
UPER circulating pumps
- Safety extra low voltage
Output voltage at Iout = 0 DC 15 V ±5%, Ri = 1 k
Output current (short-circuit- Max. 15 mA
proof)
PWM frequency 1.536 kHz
- Line length 10 m

PWM output / 10 V PWM output / 10 V output UX2 / UX3

output UX2 / UX3  PWM output As per interface definition of Grundfos for
UPER circulating pumps
- Extra-low voltage
Output voltage at Iout = 0 DC 15 V ±5%, Ri = 1 k
Output current (short-circuit- Max. 15 mA
proof)
PWM frequency 1.536 kHz
- Cable length 10 m

 10 V output
- Extra-low voltage
Output voltage at Iout = 0 DC 0..10.5 DC
Output current (short-circuit- Max. 15 mA
proof)
Calibration capability Characteristic curve coefficient
Current load 2.7 mA peak
Ripple <50 mV
Settling time 99% <500 ms
Zero point accuracy ±100 mV
Error for remaining range <0.1 V typical
<0.5 V max.
Can be calibrated by means of
parameters
- Cable length 10 m

14/30

Smart Infrastructure CC1N7471en

19.11.2021
Technical Data LMS14 (cont'd)

Control of diverting Control of stepper motor (bipolar) (X16)

valve  Outputs For 4 VA bipolar stepper motors
 Standard version LMS14 180 mA winding current (total)
 Resistance per winding 50 R < Rmotor < 110 R
- Safety extra low voltage
Voltage with output open DC 24 V
Current Max. DC 200 mA at 10% on time
- Line length 3 m
Step frequency 200 Hz

BSB users BSB terminals (X7/X30/X50)

 Operator unit AVS37
 Room unit QAA55/QAA75
- Connection 2- or 3-wire
- Cable length Max. 200 m at 1.5 mm² cross-sectional
area of cable
- Cable resistance Max. 3 x 14 
- Cross-sectional area of cable Min. 0.5 mm²
 Users Max. 5 (1 operator unit, 3 room units,
1 service unit)

15/30

Smart Infrastructure CC1N7471en

19.11.2021
Technical Data LMS14 (cont'd)

Limitation of the BSB The LMS14 may only be subjected to a maximum load of 40 mA on the BSB ports
users (CL+/CL-) and a maximum load of 400 mA on the 12 V supply.

Danger!
These maximum currents must not be exceeded by the total number of bus
users combined. To avoid uncontrollable malfunctions on the LMS14, each
system must be checked accordingly.

Current rating on BSB

Current rating on 12 V-
Devices connections (CL+/CL-) Remark
supply in mA *
in mA *
Operator units:
AVS37.294
0.2 22
AVS77.314
AVS37.294
0.2 14
AVS77.314
AVS37.290
0.2 16
AVS37.390
AVS37.291
0.2 9
AVS37.391
AVS74.261
AVS74.661 0.2 44 Illumination active
AVS74.761
AVS74.261
AVS74.661 0.2 24 Illumination not active
AVS74.761
AVS77.411 0.2 22
AVS77.410 0 10
Room units:
QAA75.611
0.2 22
QAA75.910
QAA75.611
16 0
QAA75.910
QAA75.611
0.2 14
QAA75.910
QAA55.110 7 0
QAA74.611 3-wire connection; illumination
0.2 44
QAA74.614 active
QAA74.611 2-wire connection; without
24 0
QAA74.614 illumination
Option: 3-wire connection; illumination not
QAA74.611 0.2 24 activated (switched off via
QAA74.614 parameters)
QAA78.6 0 0
Service devices:
QAA75.611 0.2 22
QAA74.611
0.2 44
QAA74.614

16/30

Smart Infrastructure CC1N7471en

19.11.2021
Technical Data LMS14 (cont'd)

Current rating on BSB

Current rating on 12 V-
Devices connections (CL+/CL-) in Remark
supply in mA *
mA *
Auxiliary modules:
AVS75.390 0.2 0
AVS75.370 0.2 0
AGU2.550 0.2 80
Others:
OZW672 0.2 0
OCI700
0.2 0
OCI611
AVS71.410
0.2 22
(RF gateway)
AVS71.393 0.2 10
* The values shown refer to the status as of July 2015 and may have to be checked.

Outputs for LED flame Outputs for connecting status LEDs (see drawing in the User Manual U7471, chapter
and LED fault (X30) Pin assignment for terminal X30)
 Voltage DC 12 V
 Current DC 2...10 mA (limit with Rv)
 Cable length <3 m

Cross-sectional area Cross-sectional area Maximum length

sensors 0.25 mm² 20 m
0.5 mm² 40 m
1 mm² 80 m
1.5 mm² 120 m

17/30

Smart Infrastructure CC1N7471en

19.11.2021
Technical Data AGU2.56xx109

General device data Degree of protection IP20

Safety class Safety class III
Pollution degree 2
Dimensions 60 x 20 x 12 mm (L x W x H)
Weight Approx. 16 g
Mounting position Optional
Lifetime Max. 300 h
Electrical data Power supply DC 5 V ±5%

Warning!
Only use the parameter stick during the parameter setting process on the
LMS14. It is not permitted to plug in the parameter stick during operation or to
use it in permanent operation!

Environmental
conditions
Warning!
Condensation, formation of ice and ingress of water are not permitted.
Failure to observe this information poses a risk of damaging the safety
functions and a risk of electric shock.

Climatic conditions Storage

Temperature range -20...60 °C
Humidity <90% r.h. (noncondensing)
Transport
Temperature range -20...60 °C
Humidity <90% r.h. (noncondensing)
Operation
Temperature range 0...60 °C
Humidity <85% r.h. (noncondensing)
Installation altitude Max. 2,000 m above sea level

Warning!
The AGU2.56 may only be connected to the LMS14 or the OCI432 on the
designated plug-in space!

18/30

Smart Infrastructure CC1N7471en

19.11.2021
Technical Data LMS15

 Note!
The data listed are only those deviating from the Technical Data of the LMS14

Basic unit Mains voltage (rated voltage) AC 230 V

Mains frequency 50 Hz to EN 298
Power consumption
 Operation Max. 25 W (with fuel valve)
 Power pack Max 25 W
Rated surge voltage category III ( DIN EN 60664)
Degree of protection IP00
IP40 (must be insured after installation
in the heating appliance)
Safety class LMS15 designed for use in equipment of
protection class I according to
EN 60730-1:2017
Degree of pollution 2
Software classes To EN 60730-2:2015 + A1:2019
 Controller part Class A
 Burner control Class C
Dimensions (L x W x D) 230 x 150 x 32 mm
Weight Ca. 0.279 kg
Unit fuse 2 x T6.3H250 internal
Mounting position Optional

Warning!
When making 100% inspections as per DIN EN 60335-1, Addendum A, only AC
voltage may be applied. If DC voltage tests are conducted, the LMS15 can get
damaged.

Environmental
conditions
Warning!
Condensation, formation of ice and ingress of water are not permitted!
Failure to observe this information poses a risk of damaging the safety
functions and a risk of electric shock.

Climatic conditions Storage

Temperature range -20...60 °C
Humidity <90% r.h. (noncondensing)
Transport
Temperature range -20...60 °C
Humidity <90% r.h. (noncondensing)
Operation
Temperature range 0...60 °C
Humidity <85% r.h. (noncondensing)
Installation altitude Max. 2,000 m above sea level

19/30

Smart Infrastructure CC1N7471en

19.11.2021
Technical Data LMS15 (cont'd)

Electrical connections
Mains voltage Total current for all network components 5 A (at UMains = AC 230 V; Ta = 25 °C)
connections connected to the LMS15 and clip-ins

Attention!
Fuse protection!
The mains voltage connection terminals are protected by the unit fuse as per
the chapter Technical data - General data.

Flame supervision/ionization probe

 Switching thresholds Min. 1.7 µA (required DC current)
 Current Typically 25...75 μA
(RFlame = 2.5...0.5 M)
Max. 119 µA (RFlame = 100 k)
 Response time in the event of loss of 1 s
flame
 Touch protection The detector electrode and their
connections must be installed in such a
way that sufficient protection against
coming into direct or indirect contact with
active components is ensured in any
unfavorable situations that may arise
during correct use.
 Cable length for flame detector 1 m

 Note!
Conductors L- and N are interchangeable!

Extra-low voltage Warning!

connections (PELV) For functional reasons, the LMS15 extra-low voltage circuits are connected to
the protective earth via X17. Therefore, they are classed as PELV circuits.

Safety limit thermostat

 Voltage DC 24 V
 Current 1 mA...1 A
Carrying power to the fuel valve and
ignition
Fuel valve
 DC output DC 24 V +10%/-15%
 Current ≤DC 0.25 A
General data for fuel valve connection
 Cable length Max. 1 m for DC
 Leak current at 1.06 x rated voltage Max. 0.5 mA
 Capacitive extra circuit or surge Not permitted
voltage limiting protective elements
External ignition module
 Voltage DC 24 V +10%/-15%
 Current 5…0.2 A
 Cable length Max. 3 m
In terms of switching performance, every external ignition module used must be
approved by Siemens!

20/30

Smart Infrastructure CC1N7471en

19.11.2021
Technical Data LMS15 (cont'd)

OpenTherm OpenTherm connection According to OpenTherm specification

V4.0
 Connection 2-wire
 Cable length Max. 50 m with a 1 mm² wire cross
section
 Cable resistance Max. 2 x 5 
 Wire cross section Min. 0.5 mm²
 User Max. 1 per connection
 Open-circuit voltage Max. 24 V DC

Functions

Note
 The scope of functions depends on the LMS1x and its respective parameterization
(refer to LMS14 User Manual U7471 or LMS15 User Manual U7472).

21/30

Smart Infrastructure CC1N7471en

19.11.2021
Basic diagram LMS14

The maximum functionality of the LMS14 system (120 V AC) is shown. The specific
scope of functions is to be determined according to the respective design /
configuration!

22/30

Smart Infrastructure CC1N7471en

19.11.2021
Basic diagram LMS14 (cont’d)

The maximum functionality of the LMS14 system (230 V AC) is shown. The specific
scope of functions is to be determined according to the respective design /
configuration!

23/30

Smart Infrastructure CC1N7471en

19.11.2021
Basic diagram LMS15

The maximum functionality of the LMS15 system is shown. The specific scope of
functions is to be determined according to the respective design / configuration!

L1, N, PE / L1, L2, PE Mains voltage Fuel valve

(L1 / N replaceable) DC 24 V
Safety temperature limiter, Stepper motor
(S)TB / TB temperature limiter fuel valve

Ignition module
Reset Lockout reset button DC 24 V

PWM fan
Programmable analog / AC 230 V
H1 digital input

Programmable analog / Multifunctional

H3 digital input output QX1

Programmable frequenzy /
H4 digital input Heating circuit pump QX2
P1
Programmable digital
RT / H5 input DHW pump 1
or diverting valve QX3
Gas pressure switch or
H6 programmable Unipolar / bipolar
digital input stepper motor Qx4
(diverting valve)
Air pressure switch or
H7 programmable Room unit S / 1 / 2 / 3
digital input
Extension module1 / 2 / 3
B2 Boiler flow sensor

Operating unit
B3 / B38 DHW sensor 1
Reset

B9 Outside sensor
LED interference
Multifunctional
BX1 sensor
LED flame
Multifunctional
BX2 sensor
Radio module

Multifunctional Parameter stick

BX3 sensor
OpenTherm
Boiler return sensor /
Return flow / BX4/ multifunctional LPB module
sensor
Modbus ClipIn

Thresholf programmable Flame supervision

(continuous)
PC tool
Line AUX1 (fuse)
Line AUX2 (fuse)

7471a45e/0918

24/30

Smart Infrastructure CC1N7471en

19.11.2021
Dimensions
Dimensions in mm
LMS14 complete (Basic)

25/30

Smart Infrastructure CC1N7471en

19.11.2021
Dimensions (cont'd)
Dimensions mm
LMS14 complete
(Medium)

26/30

Smart Infrastructure CC1N7471en

19.11.2021
Dimensions (cont'd)
Dimensions in mm

LMS14 complete
(Deluxe)

27/30

Smart Infrastructure CC1N7471en

19.11.2021
Dimensions (cont'd)
Dimensions in mm
LMS15 complete (Basic)

28/30

Smart Infrastructure CC1N7471en

19.11.2021
Dimensions (cont'd)
Dimensions in mm
LMS15 complete
(Medium)

29/30

Smart Infrastructure CC1N7471en

19.11.2021
Dimensions (cont'd)
Dimensions in mm
LMS15 complete
(Deluxe)

2021 Siemens AG Smart Infrastructure, Berliner Ring 23, D-76437 Rastatt

30/30 Subject to change!

Smart Infrastructure CC1N7471en

19.11.2021