Government Polytechnic College, Pala

GOVERMENT POLYTECHNIC COLLEGE PALA

DEPARTMENT OF ELECTRICAL AND

ELECTRONICS ENGINEERING

SEMINAR REPORT

ON

PLASTIC SOLAR CELL TECHNOLOGY

Department of EEE 2022-2023 1

 Government Polytechnic College, Pala

GOVERNMENT POLYTECHNIC COLLEGE,

PALA

DEPARTMENT OF
ELECTRICAL & ELECTRONICS ENGINEERING
CERTIFICATE

This is to certify that the Seminar Report titled ― PLASTIC SOLAR CELL
TECHNOLOGY‖ was presented by ALAN THOMAS(REG NO: 2003087) a
student of 6th semester Electrical & Electronics Engineering in partial fulfilment of
requirement for the award of Diploma in Electrical & Electronics Engineering under
the department of Technical Education, GOVERNMENT OF KERALA during the
academic year of 2022-2023 under my guidance.
Certified that, this is the bonafide record of Seminar conducted by the above
student.

Internal Examiner Head of section

External Examiner

Place: Govt. Polytechnic College Pala

Date:

Department of EEE 2022-2023 2

 Government Polytechnic College, Pala

DECLARATION

I, ALAN THOMAS, hereby declare that this seminar report on “PLASTIC

SOLAR CELL TECHNOLOGY”, submitted for partial fulfilment of requirement
for the award of Diploma in Electrical & Electronics Engineering under the
department of Technical Education, GOVT OF KERALA. This submission represents
my ideas in my own words and where ideas or words of others have been included, I
have adequately and accurately cited and referenced the original sources. I also declare
that I have adhered to ethics of academic honesty and integrity and have not
misrepresented or fabricated any data or idea or fact or source in my submission. I
understand that any violation of the above will be a cause for disciplinary action by the
institute and or the University and can also evoke penal action from the sources which
have thus not been properly cited or from whom proper permission has not been
obtained. This report has not been previously formed the basis for the award of any
degree, diploma or similar title of any other University.

ALANT THOMAS

Department of EEE 2022-2023 3

 Government Polytechnic College, Pala

ACKNOWLEDGEMENT

―Achievement is finding out what you would be doing, what you have to do. The
higher the summit, higher will be the climb.‖
It has been rightly said that we are build on the shoulders of others but the
satisfaction that accompanies the successful completion of any task would be
incomplete without the mention of the people who made it possible.
First of all I thank the god of almighty for the successful completion of this
seminar of mine.
I am extremely thankful to our principal Mrs. ANI ABRAHAM. for the careful
and precious guidance which were extremely valuable for the seminar.
Also my sincere thanks to Head of department Smt. BINU B.R, also Sri. Nevin
Jose, and all the teaching staff who provided invaluable support by guiding me
through the entire preparation period for the seminar, and also keeping me updated
with the rules, regulations, format and also the deadlines.

Finally, I thank my classmates and all others who have helped me directly or indirectly
with constant encouragement, constructive criticisms and valuable suggestions to
bring out this report a successful work.

Department of EEE 2022-2023 4

 Government Polytechnic College, Pala

ABSTRACT

This paper represents a review on recent developments in PLASTIC SOLAR CELL

TECHNOLOGY. Solar cells that are primarily of the conventional type. Photovoltaic
(PV) cells are comprised of unique materials called semiconductors, the most common
of which being silicon. When light strikes the cell, some of it is absorbed by the
semiconductor material. This indicates that the absorbed light energy is transmitted to
the semiconductor electrons are knocked loose and allowed to move freely as a result
of the energy. In addition, all PV cells features one or more electric fields that act to
push electrons released by light absorption to travel in a specific direction we can pull
this current off the top and bottom of the PV cell and use it externally by installing
metal contacts on the top and bottom of the cell
Solar cells use freely available sunlight to make electricity. At the present time, solar
electricity does not come cheap, because solar panels are rather expensive. And the
cost of solar panel is comparatively high so as a solution scientists have been working
on the new technology of plastic solar cell
Now imagine that we could reduce costs by printing solar panels Plastics are made of
polymers, which are very long molecules which is having more benefits than
compared to a conventional solar cell

Department of EEE 2022-2023 5

 Government Polytechnic College, Pala

CONTENTS
No Page no

1 INTRODUCTION 8
1.1 GLOSSARY 9
2 CONVENTIONAL SOLAR CELL 10
2.1 WORKING OF A CONVENTIONAL SOLAR CELL 11
2.2 APPLICATIONS OF CONVENTIONAL SOLAR CELL 12
3 PLASTIC SOLAR CELL 13
3.1 WORKING OF PLASTIC SOLAR CELL 14-15
3.2 THE SMALL POLYMERS 16
3.3 SPECIAL ADDITIVE 17
3.4 NEW EXPERMENTAL SETUP 18-19
3.5 ADVANTAGES OF PLASTIC SOLAR CELL 20
3.6 DIS ADVANTAGES OF PLASTIC SOLAR CELL 21
4 CONCLUSION 22
5 REFERENCE 23

Department of EEE 2022-2023 6

 Government Polytechnic College, Pala

LIST OF FIGURES
No Page no
1 SILICON SOLAR CELL 10
2 CONVENTIONAL SOLAR CELL 11
3 DIAGRAM OF A PLASTIC SOLAR CELL. 14
4 TOP VIEW MICROSCOPIC IMAGE OF A BAD
SOLAR CELL (LEFT) AND A GOOD SOLAR CELL
(RIGHT), TAKEN WITH AN ELECTRON
16
MICROSCOPE
5 PLASTIC SOLAR CELLS ARE MADE BY SPIN 17
COATING.
6 DIAGRAM OF HOW THE SPECIAL ADDITIVE 19
WORKS.

Department of EEE 2022-2023 7

 Government Polytechnic College, Pala

CHAPTER 1
INTRODUCTION

With the ever-increasing demand of electrical energy everyone is looking towards Sun
as a source of electrical energy along with its role as an important source of thermal
energy. The sun always shines and provides energy to the earth in the form of light,
even on cloudy days. Solar panels convert this light into electricity.
The most commonly known fact about solar energy is that it represents a clean, green
source of energy. Solar power is a great way to reduce your carbon footprint. There‘s
nothing about solar power that pollutes mother nature. Solar power doesn‘t release any
greenhouse gasses, and except for needing a source of clean water to function, it uses
absolutely no other resources. Hence, it‘s safe and environmentally-friendly. Yet,
people are still in doubt why solar energy is good. Solar power is self-sufficient and
installing solar panels on your roof is a safe and easy path to contribute to a
sustainable future.
At the heart of all photovoltaic devices are two separate layers of materials, one with
an abundance of electrons those function as a ‗Negative pole‘ and one with an
abundance of holes(vacant positively charged energy spaces) that functioned as a
‗positive pole‘. When photons from the Sun are absorbed, their energy is transferred
to the extra electron in negative pole, causing them to flow to positive pole & creating
new holes that start flowing to the negative pole, thus producing electrical current
which can be used to power other devices.

Department of EEE 2022-2023 8

 Government Polytechnic College, Pala

GLOSSARY

Active layer: the most important layer of plastic solar cells. This layer is where
sunlight is converted into charge.
Additive: An additive is a small chemical, which can be added to the ink, but does
not remain in the solar cell after the ink dries.
Electron microscope: A normal microscope uses light to see very small things.
However, if things are too small to see with a normal microscope, we need to use an
electron microscope. As the name implies, electrons are used instead of light.
Ink: A combination of liquid and solid materials that can be printed or coated onto a
surface. During printing or coating, the liquids evaporate and the solids remain on the
surface.
Interface: The boundary between two materials.
Polymer: A long molecule that looks like cooked spaghetti, but is a million times
smaller. Plastics contain polymers.
Spin coating: A coating method to make very thin films. A droplet of ink is put on a
glass slide, which is then rotated at high speed to spread the ink. After spreading, the
ink dries and a very thin layer is left on the glass.

Department of EEE 2022-2023 9

 Government Polytechnic College, Pala

CHAPTER 2
CONVENTION SOLAR CELL
A solar cell, or photovoltaic cell, is an electronic device that converts the energy of
light directly into electricity by the photovoltaic effect, which is a physical and
chemical phenomenon.[1] It is a form of photoelectric cell, defined as a device whose
electrical characteristics, such as current, voltage, or resistance, vary when exposed to
light. Individual solar cell devices are often the electrical building blocks of
photovoltaic modules, known colloquially as solar panels. The common single
junction silicon solar cell can produce a maximum open-circuit voltage of
approximately 0.5 to 0.6 volts.

Solar cells are described as photovoltaic, regardless of whether the source is sunlight
or artificial light. In addition to producing energy, they can be used as a photodetector
(for example infrared detectors), detecting light or other electromagnetic radiation near
the visible range, or measuring light intensity.

The operation of a photovoltaic (PV) cell requires three basic attributes:

 The absorption of light, generating excitons (bound electron-hole pairs),

unbound electron-hole pairs (via excitons), or plasmons.
 The separation of charge carriers of opposite types.
 The separate extraction of those carriers to an external circuit.

SILICON SOLAR CELL

Department of EEE 2022-2023 1

 Government Polytechnic College, Pala

2.1 WORKING OF A CONVENTIONAL SOLAR CELL

When light shines on a photovoltaic (PV) cell – also called a solar cell – that light may
be reflected, absorbed, or pass right through the cell. The PV cell is composed of
semiconductor material; the ―semi‖ means that it can conduct electricity better than an
insulator but not as well as a good conductor like a metal. There are several different
semiconductor materials used in PV cells.
When the semiconductor is exposed to light, it absorbs the light‘s energy and transfers
it to negatively charged particles in the material called electrons. This extra energy
allows the electrons to flow through the material as an electrical current. This current
is extracted through conductive metal contacts – the grid-like lines on a solar cells –
and can then be used to power your home and the rest of the electric grid.
The effeciency of a PV cell is simply the amount of electrical power coming out of the
cell compared to the energy from the light shining on it, which indicates how effective
the cell is at converting energy from one form to the other. The amount of electricity
produced from PV cells depends on the characteristics (such as intensity and
wavelengths) of the light available and multiple performance attributes of the cell.

CONVENTIONAL SOLAR CELL

Department of EEE 2022-2023 1

 Government Polytechnic College, Pala

2.2APPLICATIONS OF CONVENTIONAL SOLAR CELL

 Solar farms
. Many acres of PV panels can provide utility-scale power—from tens of megawatts to
more than a gigawatt of electricity. These large systems, using fixed or sun-tracking
panels, feed power into municipal or regional grids.
 Transportation
PV can provide auxiliary power for vehicles such as cars and boats. Automobile
sunroofs can include PV for onboard power needs or trickle-charging batteries.
Lightweight PV can also conform to the shape of airplane wings to help power high-
altitude aircraft.
 Military uses
Lightweight, flexible thin-film PV can serve applications in which portability or
ruggedness are critical. Soldiers can carry lightweight PV for charging electronic
equipment in the field or at remote bases.
 Building related needs
In buildings, PV panels mounted on roofs or ground can supply electricity. PV
material can also be integrated into a building‘s structure as windows, roof tiles, or
cladding to serve a dual purpose. In addition, awnings and parking structures can be
covered with PV to provide shading and power.
 Stand alone power
In buildings, PV panels mounted on roofs or ground can supply electricity. PV
material can also be integrated into a building‘s structure as windows, roof tiles, or
cladding to serve a dual purpose. In addition, awnings and parking structures can be
covered with PV to provide shading and power.

Department of EEE 2022-2023 1

 Government Polytechnic College, Pala

CHAPTER 3
PLASTIC SOLAR CELL

Scientists recently found a new way to make solar panels: by printing them! Most
people think about printing things like books, but we can also use a special kind of
printers to print objects made out of plastics. Plastics are made of polymers, which are
very long molecules. Under a very strong microscope, polymers look like cooked
spaghetti, but, in fact, they are a million times smaller. To print plastics, you simply
replace the ink cartridge in your printer at home with ―plastic ink.‖ The plastic ink is a
combination of two polymers dissolved in a liquid. When printed, the liquid dries and
the two polymers form a thin film. For solar cells, we use a special type of polymer
that can convert sunlight into electricity.

Plastic solar cells can be printed on large rolls of flexible foil. Recently, 100 m-long
solar panels were printed. Using these cheap solar panels, only around 1.5% of the
energy in the sunlight is converted to electricity. This efficiency is still low compared
to the expensive solar panels you can buy now, which can convert 15–20% of the
sun‘s energy into electricity. But the future looks bright. In laboratories around the
world, small plastic solar cells are already being made with much higher efficiencies,
up to about 12%

One of the tricks to increase the efficiency is adding a special additive to the plastic
ink before printing. This special additive was found by accident [4], but if we want to
improve the efficiency of the plastic solar panels even further, we need to know why
this special additive works. Understanding how plastic solar cells work is not easy.
many scientists have worked on this topic .

Department of EEE 2022-2023 1

 Government Polytechnic College, Pala

3.1 WORKING OF PLASTIC SOLAR CELL

Plastic solar cells consist of a plastic layer on glass or a flexible foil. In the lab, we use
glass plates with a transparent electric contact [the positive (+) pole]. On top of this
contact, we put the ink for the active layer, which is the part of the solar cell that
converts sunlight to electricity. This ink contains two polymers, a long green one and a
shorter red one. The polymers form a mixed layer, as shown in figure
On top of that layer, we put a metal layer, which functions as the negative (−) pole.
We then turn the whole stack of layers upside down such that sunlight can shine
through the glass into the active layer.

Diagram of a plastic solar cell.

Sunlight creates a plus (+) and a minus (−) charge at the interface between
two polymers. The (−) charge moves to the (−) pole of the solar cell and
the (+) charge to the (+) pole. These poles work just like those in a
battery, but are powered by the sun and never run out as long as the sun
shines.

Department of EEE 2022-2023 1

 Government Polytechnic College, Pala

The Structure of red and green polymers in Figure is requiredThere is a lot

of interface, or area of contact, between the two polymers. This is necessary,
because sunlight creates electrical charges only at the areas where the two
polymers are in contact. When the light is absorbed (the yellow star), positive (+)
and negative (−) electrical charges are generated. Normally, the + and − attract
each other and the energy is lost. In plastic solar cells, the red and green polymers
make sure the charges can be separated. The positive and negative charges then
move to the + and − poles. Now, light is converted to moving charges, which is
electricity! Think about how useful this is – we use free sunlight and two cheap
plastics to make electrical energy

Department of EEE 2022-2023 1

 Government Polytechnic College, Pala

3.2 THE SMALL POLYMERS

The green and red polymers are so small that we cannot see them easily, even when
using a normal microscope. But we can see them with an electron microscope, which
does not use light, but electrons to ―look‖ at the solar cells. In Figure

We show electron microscopic images of real plastic solar cells. These are images
looking down on the active layer. The two polymers show up as dark and bright areas
and not as red and green because electrons are ―colorblind.‖ On the left, a
poorly working plastic solar cell is shown. The large droplets create very little
interface and the efficiency is low: 1.5%. On the right, a much better plastic solar cell
is shown. The structure between dark and bright areas is now so small that it is
actually hard to see, but it means that there is a lot of interface. This allows for more
charges to be made and triples the efficiency to over 5%. These solar cells are still not
the best, but they can help us to understand how plastic solar cells work.

Top view microscopic image of a bad solar cell (left) and a good solar cell
(right), taken with an electron microscope

Department of EEE 2022-2023 1

 Government Polytechnic College, Pala

3.3 SPECIAL ADDITIVE

The additive is a slowly drying liquid, which is added to the ink in a small amount.
The active layers are made by a process called spin coating the ink, as shown in Figure
Spin coating is a technique to make thin films from an ink. The regular spin coating
process is shown on the top row of Figure . A drop of ink that contains the green and
red polymers in a liquid is put on a glass plate. By very fast rotation, a thin wet film
forms that dries within 1 s by evaporating the liquid. While drying, the red polymer
forms large droplets, which cause the poor performance. The bottom row shows the
same spin coating process after the additive is added to the ink. Now, drying takes
longer, about 5 s. As you see, no droplets are formed when using the special additive.

Plastic solar cells are made by spin coating.

Spin coating is a technique to make thin films. Here, a side view of this process is
shown. The top view looks like a pottery kick wheel. First (on the left), a droplet of
ink (either with or without the additive) is put on a glass plate. Then (middle), that
glass plate is rotated at high speed. Because of the rotation the ink droplet spreads out
and forms a thin film. Without additive, the ink is dry within 1 s and the red polymer
clusters in droplets (top right), which is bad for solar cell performance. With additive,
the drying takes longer and the red polymer is more spread out (bottom right), which is
good for solar cell performance

Department of EEE 2022-2023 1

 Government Polytechnic College, Pala

3.4 NEW EXPERIMENTAL SETUP

To study this drying process during the spin coating process, we had to build a new
experimental setup. In this setup, we shine a laser on the spinning glass plate. The
reflection of the laser changes when the droplets are formed. In this way, we found
that without additive the large droplets form in a late stage of the drying process, and
even later, the green polymer changes color! To understand what happens when the
color changes, we recall that the green component is a long polymer. We know that
long polymers can fold up, similar to how a snake curls up. The folding makes the
green polymers change their color to dark green. Using our special setup, we
determined the time at which the color changes and the folding happens. We
discovered that the effect of the special additive is to make the green polymer fold
earlier than it does without the additive, and even before the droplets would normally
form! The reason is that the additive and the green polymer do not like each other very
much. As a result, the green polymer folds up when it ―feels‖ the additive.the
red polymer does not form droplets. The folding of the green polymer holds back
droplet formation and results in better mixed layers.

Department of EEE 2022-2023 1

 Government Polytechnic College, Pala

Diagram of how the special additive works.

The top figure shows a small part of the ink droplet we put on the spin coater. We see
that the green polymers and the red polymers are mixed. During the spin coating,
the ink will dry. Without additive, we see a clustering of the red polymers. With
additive, we see something very different: the green polymers fold up. The folding
prevents the formation of the clusters of the red polymers.

Department of EEE 2022-2023 1

 Government Polytechnic College, Pala

3.5. ADVANTAGES OF PLASTIC SOLAR CELL

 The primary advantage of a plastic solar cell or OPV is its low cost compared to
other energy sources.
 It is also typically much easier to make than traditional silicon-based
photovoltaic cells because it uses a thin film deposition technique which
allows for the use of low-cost materials like plastics instead of just silicon chips.
 This type of cell has a much higher efficiency than traditional cells, meaning
that more light can be converted into electricity with less power loss due to heat
or air leakage as is common with other types of photovoltaics.
 Additionally, this type of cell tends to be lightweight and flexible which makes
them ideal for rooftop installation projects where weight limitations are
especially important.
 In addition, these plastic-based solar cells may not degrade as quickly or suffer
manufacturing flaws due to normal wear during shipping since they don't
require high temperatures and pressure like crystalline silicon - two factors that
impose long-term reliability issues over time with such photovoltaic
installations.
 Plastic solar cells can be manufactured at room temperature without the
expensive equipment needed for silicon-based panels and so require little capital
investment from manufacturers as well as low labor costs, making them very
attractive products for many applications.
 They also tend to work better when exposed to diffuse light rather than direct
sunlight which means they can perform even better on cloudy days compared
with their counterparts made from conventional photoelectric materials such as
polysilicon.

Department of EEE 2022-2023 2

 Government Polytechnic College, Pala

3.6. DISADVANTAGES OF PLASTIC SOLAR CELL

 One being that their performance in comparison with traditional crystalline

silicon PV systems could still be improved upon further before becoming
competitive in terms of pricing per wattage produced (especially when taking
into account total lifetime maintenance costs).
 Another disadvantage associated with this technology is its lack of durability;
although there have been vast improvements in increasing longevity by
improving encapsulation techniques works during the fabrication process due
lately to malfunctions caused by moisture penetration leading to corrosion over
time – sometimes seen firsthand within only 2 – 3 years post installation
depending upon geographical setting & conditions experienced throughout said
timeline period out above-mentioned example cases applies particularly well
towards those situated near oceanic environments wind-driven sea spray
routinely coats PV surfaces regularly up a salt-laden environment
 Lastly, this form factor remains limited in terms of performance output &
standing even amongst other prior mentioned varieties within the same niche
market regarding per wattage generated output-wise capacity still lags hence
why it vita anyone considering added instant benefits upon first use turns an eye
towards established competitors who boast larger maximum capacities overall
measured turn out rate values when selecting either residential/commercial
based models cited today throughout industry-standard catalogs worldwide
currently available.

Department of EEE 2022-2023 2

 Government Polytechnic College, Pala

CHAPTER 4
CONCLUSION
Plastic solar cells have a huge potential because they can be printed cheaply on
large flexible foils. Their efficiency still needs improvement, but can be
improved threefold by adding a special additive to the printer ink. Since this
additive is very useful, we wanted to understand how it works. With a new
experimental setup designed to study the drying of the ink, we found that the
special additive controls folding of one of the two polymers. The folding
prevents large droplets and increases the amount of interface between the two
polymers in the active layer. The interface is very important the efficient
conversion of sunlight into electricity. In the past, solar cells were optimized by
lots of hard lab work and you had to be lucky to make a good cell. Now,
because we understand the process of the drying, we can think of even more
clever tricks to optimize these solar cells! In the future, this will hopefully lead
to cheap and efficient electricity production from printed solar panels

Department of EEE 2022-2023 2

 Government Polytechnic College, Pala

CHAPTER 5
REFERENCES

 U.S. Energy Information Administration. 2015. Monthly Energy Review.

Available from: http://www.eia.gov/
 Krebs, F. C., Espinosa, N., Hösel, M., Søndergaard, R. R., Jørgensen, M. 2013.
25th anniversary article: rise to power – OPV-based solar parks. Adv. Mater.
26:29–39. Doi: 10.1002/adma.201302031
 Yusoff, A. R. B. M., Kim, D., Kim, H. P., Shneider, F. K., da Silva, W. J., Jang,
J. 2015. High efficiency solution processed polymer inverted triple-junction
solar cells exhibiting conversion efficiency
 Van Franeker J and Janssen R (2015) Plastic Solar Cells: Understanding the
Special Additive. Front. Young Minds.
 Peet, J., Kim, J. Y., Coates, N. E., Ma, W. L., Moses, D., Heeger, A. J., et al.
2007. Efficiency enhancement in low-bandgap polymer solar cells by
processing with alkane dithiols.

Department of EEE 2022-2023 2