many years of practice in the field of direct fastening into thermoplastic materials. Several years of research have led to the conclusi- on that the clamp load of thermoplastic joints can be calculated (VDI 2230). A prognosis programme and the DELTA PT® srew with it‘s optimised thread geometry were developed. The result is a tough fastener that guarantees safety and reliability even in extreme applications. EJOT DELTA PT® for selftapping Advantages of the EJOT PT® screw: in thermoplastic materials l Minimal radial tension due to optimized flank angle Boss design l High clamp loads The most favourable hole diameter has in most l High tensile and torsion strength cases proven to be: l Increased cycle stress stability l High strength under vibration dh = 0,8 x d1 ± tolerance of screwdiameter ® l DELTA PT prognosis programme allows a clamp (see tolerance brochure page 16) load oriented engineering l Long lifetime of the joint For higher filled materials or materials with a bigger l Standard material through hardened steel [PT10] strength the hole diameter can be increased up to dh = 0,88 x d1.
dT = 2 x d1 > = dC dC 0,3 to 0,4 x d1
di = 2 x d1
dh = 0,8 x d1 0,5 x d1
d1 = Nominal-Ø of the screw
dC = d1 x 1,05 Application sample into manyfold Chrom VI free surfaces: l zinc clear / blue passivated l zinc clear / blue passivated with EJOSEAL Fastener materials: (240h resistance to Zn-corrosion) l Through hardened steel l zinc clear / thick film passivation according to DIN EN ISO 10263 T4 l ZnFe or ZnNi / transparent passivated with material property [PT 10] (WN 5461, part 2) (with or without black top coats) l Stainless steel [A2], [A4] l ZnNi, black passivated l Aluminium [Alu] l zinc flake coatings (depending on Ø) (e.g. Delta Protekt)
Ø d1 [mm] 1,0 1,2 1,4 1,6 1,8 2,0 2,2 2,5 3,0 3,5 4,0 4,5 5,0 6,0 7,0 8,0 10,0 Length [mm] 3,0 3,5 4,0 4,5 5,0 6,0 7,0 R (S) 8,0 R R R S (S) 9,0 R R R R, S S (S) 10,0 R R R R, S S (S) 12,0 R R R R, S R, S S (S) (S) 14,0 R R R R, S R, S R, S R, S (S) (S) 15,0 R R R R, S R, S R, S R, S S (S) 16,0 R R R R, S R, S R, S R, S R, S (S) (S) 18,0 R R R R, S R, S R, S R, S R, S R, S (S) 20,0 R R R, S R, S R, S R, S R, S R, S S 21,0 R R, S R, S R, S R, S R, S R, S R, S 22,0 R R, S R, S R, S R, S R, S R, S R, S 24,0 R, S R, S R, S R, S R, S R, S R, S 25,0 R, S R, S R, S R, S R, S R, S R, S 27,0 R, S R, S R, S R, S R, S R, S 30,0 R, S R, S R, S R, S R, S R, S 35,0 R, S R, S R, S R, S R, S 36,0 R, S R, S R, S R, S 40,0 R, S R, S R, S R, S 42,0 R, S R, S R, S 45,0 R, S R, S R, S 08.09 All technical data may be subject to technical improvements.
48,0 R, S R, S 50,0 R, S R, S 60,0 R, S 70,0 80,0 100,0 Upper line ∧ = minimal length Length > 60 mm with partial thread only (countersunk head length Lmin = L + 2 mm) (partial thread length 4 x d1) ∧ maximal length Lower line = Special geometries upon request!
S Manufacturing with cutting edge possible
(S) Manufacturing with cutting edge possible (not in connection with WN 5411 and WN 5451) R Manufacturing with pilot point possible (length tolerance acc. js 17)
For more information please contact Volker Dieckmann, phone +49 2752 109-142, fax 109-141, email [email protected]
