Touch-Up, Recoat, and Stripping

Chapter 10: Touch-up, Recoat, and Stripping
ten
Touch-up, Recoat, and Stripping
The methods of part repair after powder coating can be put

into two categories—touch-up and recoat.
Touch-up repair is appropriate when a small area of the coated
part is not covered and is unable to meet finishing specifications.
When hanger marks are not acceptable, touch-up is required.
Touch-up also may be used to repair slight damage from handling,
machining, or welding during assembly. Touch-up is performed
using a compatible liquid paint designed for spot application by
the powder coating formulator.
Recoat is required when a part is rejected because of a large
surface area defect or when touch-up is not acceptable. At this
point, there are a variety of options that should be considered
carefully. Usually the rejected part can be repaired with a second
coat. Another option is stripping and repainting the part. Strip-
ping can also clean part hangers to provide a good ground for elec-
trostatic spray.
TOUCH-UP
Liquid touch-up paint is applied with a small brush, aerosol
spray, or airless gun. The paint is air-dried. The drying process
can be accelerated with a low-temperature bake. Touch-up paint
is used after the powder coating has been fully cured in a bake
oven. Hanger marks, light spots in corners and seams, damage
from welding or assembly, and other small defects can be touched
up. Generally, a color-matched acrylic enamel or lacquer is used.
Touch-up paint cannot be used if it will not meet the performance
127
User’s Guide to Powder Coating
specifications required during the expected life of that part. Touch-

up should not be used to repair a faulty finish unless the resulting
product meets inspection standards. Before use, the original pow-
der coating formulator should approve all touch-up paints.
RECOAT
Applying a second coat of powder is the common approach to
repair and reclaim rejected parts. However, the defect should be
carefully analyzed and the source corrected before recoating. Do
not recoat if the reject is caused from a fabrication defect, poor-
quality substrate, poor cleaning or pretreatment, or when the
thickness of two coats together will be out of tolerance. Also, if
the part is rejected due to undercure, it merely needs to be rebaked
at the required schedule.
A second coat is effective to cover light areas, surface defects
from dirt and contamination, rough spots from heavy film build
or gun spitting, and color change from severe overbake. Rough
surfaces and protrusions should be sanded smooth before
recoating.
Parts inspected on-line can be left on the conveyor to receive a
second coat. These parts can pass through the pretreatment stages
with raw parts. If the recoated parts show water spots or stains,
an adjustment can be made in the final rinse stage. Chemical sup-
pliers can offer recommendations. When parts for recoat are hung
together, cleaning and pretreatment is not necessary. However, if
the rejected parts have been stored to accumulate a practical num-
ber, they should be checked for dirt and contamination before
recoating.
Coat Entire Part

The second coat should be applied to the entire part at the de-
sired film thickness. A common mistake is to coat only the defect
area. This leaves a rough gritty surface where there is only a very
thin overspray layer of powder on the remainder of the part. The
same recommended cure schedule should be used for the second
coat.
128
Intercoat adhesion can be checked after recoating on selected

samples by using the crosshatch test or simply scratching the sur-
face to see if the second coat peels easily from the first. Some
powder coatings may need to be lightly sanded to provide a good
anchor for the second coat.
Rebake
When a part is undercured during the first coat, just returning
it to the bake oven for a normal cure schedule at the specified
time and temperature can repair it. Properties can be recovered
when a part is properly cured, with some exceptions, such as when
certain chemically controlled, low-gloss coatings are used. Partial
curing will result in a higher gloss.
STRIPPING
Usually the last alternative for part repair, stripping rejected
parts can add greatly to production costs, as well as disrupt the
production-line flow. Stripping coated parts becomes necessary,
however, when poor pretreatment or touch-up causes the coating
to be unacceptable and, therefore, rejected.
On the other hand, stripping plays an important role in the
effectiveness of a powder-coating line by resulting in clean hang-
ers that provide good electrical grounding. Hangers should be
stripped periodically.
Chemical Strippers
Chemical strippers can be used hot (raised temperature) or cold
(ambient) in a dip tank. There are acid, alkaline, and molten-salt
types, with selection dependent on the type of parts, the hangers,
and the coating to be removed. The main advantage of chemical
strippers is the low initial capital investment for equipment. Dis-
advantages include safety hazards related to handling the chemi-
cals; the high costs of chemical replacement and disposal; and that
the chemicals are laden with paint. Some parts, such as alumi-
num alloys, may not be able to withstand corrosion that can re-
sult from chemical strippers.
129
User’s Guide to Powder Coating
Burn-off Ovens
Burn-off, or pyrolysis, ovens are for stripping. They use high
temperatures to incinerate the coating. Burn-off ovens can be
batch-type or on-line ovens that operate at about 800° F (427° C),
with the pollution-control exhaust operating at temperatures of
approximately 1,200–1,300° F (649–704° C). Burn-off ovens elimi-
nate pollution and disposal problems. They are relatively efficient
to operate, but require a large capital investment and need some
type of post-cleaning to remove residual ash. The parts must with-
stand 800° F (427° C) temperatures. Some coating chemistries are
not suitable for this stripping technique. It is wise to consult with
the equipment manufacturer and local regulatory agencies for
more information. It also should be noted that repeated stripping
of tooling might require that a resilient type of alloy be used to
prevent breaking or deforming.
Shot Blasting
Shot blasting, or abrading, can be used to strip parts or hang-
ers when other methods have been ruled out. This process is very
slow, due to the toughness of the cured powder coating. The dis-
advantage of this process is that it erodes (thins) the tooling and
exposes more surface area, which becomes harder to strip when
recoated.
Cryogenic Stripping
Cryogenic stripping embrittles film with liquid nitrogen, and
then uses a nonabrasive shot blast to easily remove the coating.
This is a fast, nonpolluting method, but it requires specialized
equipment. Parts must endure –100° F (–73° C) temperatures, and
an alloy may need to be considered for tooling.
Stripping Cured Coatings

Stripping is an important function of any modern organic fin-
ishing operation, and is often the most antiquated link in the over-
all coatings process. Whether for the salvage of rejected coated
components, or as part of routine line maintenance, stripping of
130
cured coatings has an important impact on overall line quality

and economy.
When evaluating the stripping of a rejected coated part, the
first question to ask is whether the component is valuable enough
to warrant stripping, or if it should simply be scrapped. Assuming
that it is worth the cost, compatibility with the selected stripping
method must be determined. The type and quantity of coatings
also strongly influence the performance of the stripping method.
In some instances, simple compatibility may not be sufficient.
Engineered components may require specific heat treatments that
may be compromised by thermal stripping methods.
Evaluation
The best evaluation method for choosing a stripping system is
to work with the various vendors and have actual coated samples
processed by them. Their reports should contain basic informa-
tion such as how much coating was stripped, how long it took,
and whether any secondary cleaning operations were necessary.
Based on these findings and throughput needs, an estimate for
capital and operating costs can be generated and compared.
131

Touch-Up, Recoat, and Stripping

Uploaded by

Copyright:

Available Formats

Touch-Up, Recoat, and Stripping

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Touch-Up, Recoat, and Stripping

Uploaded by

Copyright:

Available Formats

Chapter 10: Touch-up, Recoat, and Stripping

The methods of part repair after powder coating can be put

specifications required during the expected life of that part. Touch-

Coat Entire Part

Intercoat adhesion can be checked after recoating on selected

Stripping Cured Coatings

cured coatings has an important impact on overall line quality

You might also like