Scribd Logo
Upload

Welcome to Scribd!

  • 23 views

    Procédure Installation Des Porte-Fusibles

    Uploaded by

    ouamor djelouadji

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Procédure Installation Des Porte-Fusibles

    Uploaded by

    ouamor djelouadji
    23 views2 pages

    Original Title

    Procédure installation des porte-fusibles

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    23 views2 pages

    Procédure Installation Des Porte-Fusibles

    Uploaded by

    ouamor djelouadji

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 2

    1 of 2

    INSTALL ATION INSTRUCTIONS

    Street lighting kit, 65U / SLK / SDK


    Inline fuse / Disconnect

    IMPORTANT
    Read and understand all instructions and
    safety information before use. Be aware
    of proper usage and potential hazards.

    WARNING: Risk of shock, disconnect Step 1


    power before installation • Measure cable diameter. Refer to Table 1, select
    corresponding section on molded sleeve. Cut off remaining
    CAUTION: Product must be installed by a sections of housing to size referenced in Range column,
    qualified electrician in accordance with Table 1. Example: If cable OD is 0.390 inch, it falls within the
    national and local electrical codes. AWG 4-2 range - cut at 4-2 line.

    Table 1
    CAUTION: Identify LINE and LOAD sides Range Cable O.D. (inch)
    of wiring and molded connector bodies 14-10 0.120-0.205
    before beginning installation. These 8-6 0.195-0.330
    instructions are not intended as a 4-2 0.320-0.430
    substitute for adequate training or
    experience in such safety practices. These
    instructions do not attempt to provide for Step 2
    every possible contingency. • Thoroughly clean approximately 8" along load side cable end.
    Apply lubricant and insert cable through small hole in load
    Contents: side (plug) housing. Push through a sufficient distance to
    • (A) Line side (Receptacle) housing permit 3/8" stripping of insulation. Strip insulation a distance
    • (B) Load side (Plug) housing of 3/8" as shown.

    • (C) Fuse holder


    8"
    • (D) Connecting link (SDK only)
    • (E) Fuse (Not included) Insert
    • Assembly Dowel
    Load side
    • Lubricant (plug) housing

    ⅜" Strip
    length

    (C)

    (D)

    (A) (B) (E)


    2 of 2

    STEP 3 • Apply lubricant lightly to outside of fuse holder. Place the


    • Insert cable into crimp barrel of fuse holder and crimp. Refer wood dowel into socket and position the free end of dowel
    to Table 2 for suggested tool and die. against a firm surface. Push the load side (plug) housing
    forward until fuse holder snaps into position. Wipe off any
    STEP 4
    excess lubricant.
    Fuse holder
    STEP 5

    Fuse holder Firm


    Insert Surface

    Crimp Push
    Wood dowel
    Fuse holder
    in lock position

    A A

    1 Section A-A

    2 3 • Repeat all the above steps with line side (receptacle) housing.
    Crimp location
    STEP 6
    Table 2
    • Insert 13/32” by 11/2" fuse (600 Volt 30 Amp max.) or connecting
    Crimp Conductor size AWG Recommended tool and dies
    area link into the plug (load side) housing.
    Stranded Solid T&B tool No. Die type
    1 14 12, 14 WT111M “C” cavity STEP 7
    1 10,12 8, 10 WT111M “C” cavity
    2 8 6 TBM45S “Blue” cavity
    2 6 4 TBM45S “Blue” cavity
    Large contact
    3 4 2 TBM45S “Gray” cavity Fuse

    3 2 — TBM45S “Brown” cavity


    WARNING:
    DO NOT use glass body fuse

    • Connect load side (plug) and line side (receptacle) housings


    together.

    Street lighting kit, 65U / SLK / SDK | Installation Instructions | 233_R2 | 0054416 C

    —
    tnb.abb.com (US/Latin America) We reserve the right to make technical We reserve all rights in this document and
    tnb.ca.abb.com (Canada) changes or modify the contents of this in the subject matter and illustrations
    abb.com document without prior notice. With contained therein. Any reproduction
    Warranty: tnb.abb.com/ecpwarranty regard to purchase orders, the agreed – in whole or in part – is forbidden without
    particulars shall prevail. ABB does not prior written consent of ABB.
    accept any responsibility whatsoever for Copyright© 2019 ABB. All rights reserved.
    potential errors or possible lack of
    information in this document.

    You might also like