Switches
Switches
Page 1 of 7
Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D EXCAVATOR CXY
Configuration: 320D & 320D L Excavators CXY00001-UP (MACHINE)
POWERED BY 3066 Engine
Systems Operation
320D, 323D, 324D, 325D, 328D and 330D Excavators Machine Electronic Control System
Media Number -RENR9848-01 Publication Date -01/03/2006 Date Updated -08/03/2006
i02412745
Switches
SMCS - 1435; 7332
Illustration 1 g00629971
Engine Speed Dial Switch
(1) Switch
(2) Schematic
The Machine ECM converts a signal of the Engine Speed Dial into a pulse width modulated (PWM) signal.
The Engine ECM receives the PWM signal in order to control the engine speed at 10 stages. The position of
the Engine Speed Dial is indicated on the display of the Monitoring System.
Illustration 2 g01159070
Switch Panel
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/med... 4/12/2007
320D & 320D L Excavators CXY00001-UP (MACHINE) POWERED BY 3066 Engine(SEB... Page 3 of 7
Illustration 3 g01144596
Right Joystick (3-Button, Trigger Switch)
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/med... 4/12/2007
320D & 320D L Excavators CXY00001-UP (MACHINE) POWERED BY 3066 Engine(SEB... Page 4 of 7
Illustration 4 g01145300
Right Joystick (2-Button, Slide, Trigger Switch)
The one touch low idle switch is located on the right joystick handle (See Illustrations 3 and 4). The one
touch low idle switch will automatically reduce engine speed to 1020 RPM. Both joystick handles (LH and
RH) must be in the neutral position before the engine speed is reduced.
Pressure Switch
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/med... 4/12/2007
320D & 320D L Excavators CXY00001-UP (MACHINE) POWERED BY 3066 Engine(SEB... Page 5 of 7
Illustration 5 g00663092
Travel Pressure Switch
Travel Pressure Switch, Implement Pressure Switch, Medium Pressure Switch, Joystick
Pressure Switch, and Attachment Pedal Pressure Switch (Hammer)
These pressure switches will monitor the hydraulic system. This switch is normally open. These switches
will inform the controller about the status of the hydraulic demands. When there is no hydraulic demand
these switches are open. The function of the automatic engine speed control (ECM) of the controller will use
these switches to determine control of the engine speed and control of the pump.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/med... 4/12/2007
320D & 320D L Excavators CXY00001-UP (MACHINE) POWERED BY 3066 Engine(SEB... Page 6 of 7
Illustration 6 g00291705
Key Start Switch
The key start switch is an input of the engine and pump controller. The key start switch informs the ECM of
an attempt to start the engine. Then, the ECM initiates the start procedure.
During normal machine operation, the start terminal of the key start switch is open. If the key start switch is
placed in the START position the start terminal will close. +Battery voltage is supplied to the start terminal.
When all starting conditions are satisfied, the ECM sends a +battery signal to the start relay and engine
cranking begins.
Note: After the key start switch is initially turned to the START position, the switch will not return to the
START position from the ON position. The switch must be turned to the OFF position first. Then, the
switch can be turned to the START position.
Toggle Switch
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/med... 4/12/2007
320D & 320D L Excavators CXY00001-UP (MACHINE) POWERED BY 3066 Engine(SEB... Page 7 of 7
Illustration 7 g01157913
Backup Switch 1
Copyright 1993 - 2007 Caterpillar Inc. Thu Apr 12 16:32:13 UTC+0630 2007
All Rights Reserved.
Private Network For SIS Licensees.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/med... 4/12/2007