PT.

ENERGASINDO HEKSA KARYA

PT. PUSTEK ENERGI & TEKNOLOGI

FRONT END ENGINEERING DESIGN (FEED)

IKPP PERAWANG RIAU

DATASHEET FOR PRESSURE SAFETY VALVE

DOC. NO. : EHK-IKPP-IS-DTS-005

2 27-03-23 Re-Issued for Approval BS HAR MDZ

1 13-03-23 Re-Issued for Approval BS HAR MDZ
0 25-11-22 Issued for Approval BS EA MDZ
REV DATE DESCRIPTION PREP’D CHK’D APP’D
PT. PUSTEK E&T PT. EHK
 DATASHEET FOR PRESSURE
Date : 27/03/2023
SAFETY VALVE

Rev : 2 DOC. NO. : EHK-IKPP-IS-DTS-005 Page : 2 of 7

TABULATION OF REVISION SHEET

REVISION REVISION
Sheet Remarks Sheet Remarks
0 1 2 3 4 0 1 2 3 4
1 X
2 X
3 X
4 X
5 X
6 X
7 X
8
9
10

ATTACHMENT
 DATASHEET FOR PRESSURE
Date : 27/03/2023
SAFETY VALVE

Rev : 2 DOC. NO. : EHK-IKPP-IS-DTS-005 Page : 3 of 7

RECORD OF REVISION

Rev. Implemented
Section Page Company's Comment Explanation
Code (Y/N)
Add PSV for area Dry Gas
0 All All Y
Filter
0 Item 1 4-7 Update Tag No. PSV Y
Update Size as per sizing
0 Item 8 4-7 Y
calculation
Is spring 316SS common?
0 Item 15 4-7 Commonly used chrome Y Revise to chrome alloy
alloy

0 Item 25 4-7 Check flowrate of fire case Y Flowrate is updated as per

process data and calculation
All Cases of PSV are revised
1 - 4-7 Y
to block discharge
All Normal gas flow of PSV
1 - 4-9 are revised to 17 MMSCFD Y
(35200 lb/hr)
 Date : 27/03/2023 DATASHEET FOR PRESSURE SAFETY VALVE

Rev : 2 DOC. NO. : EHK-IKPP-IS-DTS-005 Page : 4 of 7

MANUFACTURER : (HOLD)
1 TAG NUMBER PSV-11301-02
2 SERVICE VENT OF PIG RECEIVER
3 P&ID NO LINE/VESSEL NUMBER EHK-IKPP-PR-DWG-006 PR-11301-01
4 GENERAL FULL NOZZLE/ SEMI NOZZLE FULL
5 SAFETY/ RELIEF SAFETY
6 CONVENTIONAL/BELLOWS/PILOT OP. CONVENTIONAL
7 BONNET TYPE CLOSED
8 SIZE INLET (in) OUTLET (in) 2" 3" 2
9 CONNECTION FLANGE RATING INLET (in) OUTLET 600# 150#
10 TYPE OF FACING RF
11 BODY AND BONNET ASTM A216 WCB
12 SEAT AND RINGS 316 SS
13 RESILIENT SEAT SEAL MFR STD
14 MATERIAL GUIDE AND RINGS MFR STD
15 SPRING CHROME ALLOY
16 BELLOWS N/A
17 NOZZLE & DISC 316 SS
18 CODE ASME SEC. VIII
19 CASE BLOCK DISCHARGE 2
BASIS
20 SIZING BASIS API 520
21 VALVE DISCHARGE COEFFICIENT(Kd) 0.975
22 FLUID PROCESS GAS
23 STATE GAS
24 NORMAL GAS FLOW (lb/hr) 35200
25 VALVE CAPACITY (lb/hr) 37367 2
26 MOLECULAR WEIGHT OF GAS(MW) 19.23
27 COMPRESSIBILITY FACTOR 0.884
28 RATIO OF SPECIFIC HEAT 1.454
29 DENSITY (lb/ft3) 2.314
30 REQUIRED CAPACITY OF LIQUID (lb/hr) N/A
31 OPERATING DENSITY OF LIQ (lb/ft3) N/A
32 OPERATING VISCOSITY OF LIQ (cP) N/A
33 SP. VOL. LIQ (ft3/lb) N/A
FLUID DATA
34 SP.VOL MIXTURE@RELIEVING PRESS. (ft3/lb)
35 SP. VOL [email protected] RELIEVING PRESS. (ft3/lb)
36 OPER. PRESS. (psig) SET PRESS. (psig) 485.23 830
37 OPER. TEMP. (°F) RELIEF TEMP. (°F) 72.49 510
38 SUPERIMPOSED BACK CONSTANT (psig) 14.7
39 PRESS VARIABLE (psig)
40 BUILT UP BACK PRESSURE (psig)
41 TOTAL BACK PRESSURE (psig) 14.7
42 %ALLOWABLE OVER PRESSURE 10
43 BAROMETRIC PRESSURE 14.7
44 WET. AREA(FOR VESSEL) (ft2) -
45 LATENT HEAT OF VAPOR (Btu/lb) -
46 CALC. AREA (in2) VTA
47 SELECTED AREA (in2) VTA
CALCULATION
48 ORIFICE DESIGNATION VTA
RESULT
49 VALVE RELIEF CAPACITY (lb/hr) VTA
50 MFR. MODEL NO. VTA
51 CAP (SCREWED / BOLTED) SCREWED
52 LEVER (PLAIN / PACKED) NO
53 OPTION TEST GAUGE NO
54 RUPTURE DISC NO
55 PAINTING NOTE 3
NOTE:
1. ALL INSTRUMENT SHALL BE TAGGED WITH 316 SS NAMEPLATE SHOWING TAG NO.
2. VENDOR SHALL BE REFER TO PT. ENERGASINDO HEKSA KARYA VENDOR LIST (AVL)
3. PAINTING SPECIFICATION REFER TO EHK-IKPP-PL-SPC-002 SPECIFICATION EXTERNAL PIPE COATING.
4. VTA = VENDOR TO ADVISE
 Date : 27/03/2023 DATASHEET FOR PRESSURE SAFETY VALVE

Rev : 2 DOC. NO. : EHK-IKPP-IS-DTS-005 Page : 5 of 7

MANUFACTURER : (HOLD)
1 TAG NUMBER PSV-11501-02
2 SERVICE DRY GAS FILTER TO VENT HEADER
3 P&ID NO LINE/VESSEL NUMBER EHK-IKPP-PR-DWG-007 DGF-11501-01
4 GENERAL FULL NOZZLE/ SEMI NOZZLE FULL
5 SAFETY/ RELIEF SAFETY
6 CONVENTIONAL/BELLOWS/PILOT OP. CONVENTIONAL
7 BONNET TYPE CLOSED
8 SIZE INLET (in) OUTLET (in) 2.5" 4" 2
9 CONNECTION FLANGE RATING INLET (in) OUTLET 300# 150#
10 TYPE OF FACING RF
11 BODY AND BONNET ASTM A216 WCB
12 SEAT AND RINGS 316 SS
13 RESILIENT SEAT SEAL MFR STD
14 MATERIAL GUIDE AND RINGS MFR STD
15 SPRING CHROME ALLOY
16 BELLOWS N/A
17 NOZZLE & DISC 316 SS
18 CODE ASME SEC. VIII
19 CASE BLOCK DISCHARGE
BASIS 2
20 SIZING BASIS API 520
21 VALVE DISCHARGE COEFFICIENT(Kd) 0.975
22 FLUID PROCESS GAS
23 STATE GAS
24 NORMAL GAS FLOW (lb/hr) 35200
25 VALVE CAPACITY (lb/hr) 56748 2
26 MOLECULAR WEIGHT OF GAS(MW) 19.23
27 COMPRESSIBILITY FACTOR 0.885
28 RATIO OF SPECIFIC HEAT 1.452
29 DENSITY (lb/ft3) 2.287
30 REQUIRED CAPACITY OF LIQUID (lb/hr) N/A
31 OPERATING DENSITY OF LIQ (lb/ft3) N/A
32 OPERATING VISCOSITY OF LIQ (cP) N/A
33 SP. VOL. LIQ (ft3/lb) N/A
FLUID DATA
34 SP.VOL MIXTURE@RELIEVING PRESS. (ft3/lb)
35 SP. VOL [email protected] RELIEVING PRESS. (ft3/lb)
36 OPER. PRESS. (psig) SET PRESS. (psig) 485.23 720
37 OPER. TEMP. (°F) RELIEF TEMP. (°F) 72.49 394.86
38 SUPERIMPOSED BACK CONSTANT (psig) 14.7
39 PRESS VARIABLE (psig)
40 BUILT UP BACK PRESSURE (psig)
41 TOTAL BACK PRESSURE (psig) 14.7
42 %ALLOWABLE OVER PRESSURE 10
43 BAROMETRIC PRESSURE 14.7
44 WET. AREA(FOR VESSEL) (ft2) -
45 LATENT HEAT OF VAPOR (Btu/lb) -
46 CALC. AREA (in2) VTA
47 SELECTED AREA (in2) VTA
CALCULATION
48 ORIFICE DESIGNATION VTA
RESULT
49 VALVE RELIEF CAPACITY (lb/hr) VTA
50 MFR. MODEL NO. VTA
51 CAP (SCREWED / BOLTED) SCREWED
52 LEVER (PLAIN / PACKED) NO
53 OPTION TEST GAUGE NO
54 RUPTURE DISC NO
55 PAINTING NOTE 3
NOTE:
1. ALL INSTRUMENT SHALL BE TAGGED WITH 316 SS NAMEPLATE SHOWING TAG NO.
2. VENDOR SHALL BE REFER TO PT. ENERGASINDO HEKSA KARYA VENDOR LIST (AVL)
3. PAINTING SPECIFICATION REFER TO EHK-IKPP-PL-SPC-002 SPECIFICATION EXTERNAL PIPE COATING.
4. VTA = VENDOR TO ADVISE
 Date : 27/03/2023 DATASHEET FOR PRESSURE SAFETY VALVE

Rev : 2 DOC. NO. : EHK-IKPP-IS-DTS-005 Page : 6 of 7

MANUFACTURER : (HOLD)
1 TAG NUMBER PSV-11501-03
2 SERVICE DRY GAS FILTER TO VENT HEADER
3 P&ID NO LINE/VESSEL NUMBER EHK-IKPP-PR-DWG-007 DGF-11501-02
4 GENERAL FULL NOZZLE/ SEMI NOZZLE FULL
5 SAFETY/ RELIEF SAFETY
6 CONVENTIONAL/BELLOWS/PILOT OP. CONVENTIONAL
7 BONNET TYPE CLOSED
8 SIZE INLET (in) OUTLET (in) 2.5" 4" 2
9 CONNECTION FLANGE RATING INLET (in) OUTLET 300# 150#
10 TYPE OF FACING RF
11 BODY AND BONNET ASTM A216 WCB
12 SEAT AND RINGS 316 SS
13 RESILIENT SEAT SEAL MFR STD
14 MATERIAL GUIDE AND RINGS MFR STD
15 SPRING CHROME ALLOY
16 BELLOWS N/A
17 NOZZLE & DISC 316 SS
18 CODE ASME SEC. VIII
19 CASE BLOCK DISCHARGE
BASIS 2
20 SIZING BASIS API 520
21 VALVE DISCHARGE COEFFICIENT(Kd) 0.975
22 FLUID PROCESS GAS
23 STATE GAS
24 NORMAL GAS FLOW (lb/hr) 35200
25 VALVE CAPACITY (lb/hr) 56748 2
26 MOLECULAR WEIGHT OF GAS(MW) 19.23
27 COMPRESSIBILITY FACTOR 0.885
28 RATIO OF SPECIFIC HEAT 1.452
29 DENSITY (lb/ft3) 2.287
30 REQUIRED CAPACITY OF LIQUID (lb/hr) N/A
31 OPERATING DENSITY OF LIQ (lb/ft3) N/A
32 OPERATING VISCOSITY OF LIQ (cP) N/A
33 SP. VOL. LIQ (ft3/lb) N/A
FLUID DATA
34 SP.VOL MIXTURE@RELIEVING PRESS. (ft3/lb)
35 SP. VOL [email protected] RELIEVING PRESS. (ft3/lb)
36 OPER. PRESS. (psig) SET PRESS. (psig) 485.23 720
37 OPER. TEMP. (°F) RELIEF TEMP. (°F) 72.49 394.86
38 SUPERIMPOSED BACK CONSTANT (psig) 14.7
39 PRESS VARIABLE (psig)
40 BUILT UP BACK PRESSURE (psig)
41 TOTAL BACK PRESSURE (psig) 14.7
42 %ALLOWABLE OVER PRESSURE 10
43 BAROMETRIC PRESSURE 14.7
44 WET. AREA(FOR VESSEL) (ft2) -
45 LATENT HEAT OF VAPOR (Btu/lb) -
46 CALC. AREA (in2) VTA
47 SELECTED AREA (in2) VTA
CALCULATION
48 ORIFICE DESIGNATION VTA
RESULT
49 VALVE RELIEF CAPACITY (lb/hr) VTA
50 MFR. MODEL NO. VTA
51 CAP (SCREWED / BOLTED) SCREWED
52 LEVER (PLAIN / PACKED) NO
53 OPTION TEST GAUGE NO
54 RUPTURE DISC NO
55 PAINTING NOTE 3
NOTE:
1. ALL INSTRUMENT SHALL BE TAGGED WITH 316 SS NAMEPLATE SHOWING TAG NO.
2. VENDOR SHALL BE REFER TO PT. ENERGASINDO HEKSA KARYA VENDOR LIST (AVL)
3. PAINTING SPECIFICATION REFER TO EHK-IKPP-PL-SPC-002 SPECIFICATION EXTERNAL PIPE COATING.
4. VTA = VENDOR TO ADVISE
 Date : 27/03/2023 DATASHEET FOR PRESSURE SAFETY VALVE

Rev : 2 DOC. NO. : EHK-IKPP-IS-DTS-005 Page : 7 of 7

MANUFACTURER : (HOLD)
1 TAG NUMBER PSV-11501-01
2 SERVICE OUTLET PCV (INLET ORIFICE METER) TO VENT HEADER
3 P&ID NO LINE/VESSEL NUMBER EHK-IKPP-PR-DWG-009 10"-LN-11501-10
4 GENERAL FULL NOZZLE/ SEMI NOZZLE FULL
5 SAFETY/ RELIEF SAFETY
6 CONVENTIONAL/BELLOWS/PILOT OP. CONVENTIONAL
7 BONNET TYPE CLOSED
8 SIZE INLET (in) OUTLET (in) 3" 4" 2
9 CONNECTION FLANGE RATING INLET (in) OUTLET 300# 150#
10 TYPE OF FACING RF
11 BODY AND BONNET ASTM A216 WCB
12 SEAT AND RINGS 316 SS
13 RESILIENT SEAT SEAL MFR STD
14 MATERIAL GUIDE AND RINGS MFR STD
15 SPRING CHROME ALLOY
16 BELLOWS N/A
17 NOZZLE & DISC 316 SS
18 CODE ASME SEC. VIII
19 CASE BLOCK DISCHARGE
BASIS 2
20 SIZING BASIS API 520
21 VALVE DISCHARGE COEFFICIENT(Kd) 0.975
22 FLUID PROCESS GAS
23 STATE GAS
24 NORMAL GAS FLOW (lb/hr) 35200
25 VALVE CAPACITY (lb/hr) 35545 2
26 MOLECULAR WEIGHT OF GAS(MW) 19.23
27 COMPRESSIBILITY FACTOR 0.935
28 RATIO OF SPECIFIC HEAT 1.365
29 DENSITY (lb/ft3) 1.068
30 REQUIRED CAPACITY OF LIQUID (lb/hr) N/A
31 OPERATING DENSITY OF LIQ (lb/ft3) N/A
32 OPERATING VISCOSITY OF LIQ (cP) N/A
33 SP. VOL. LIQ (ft3/lb) N/A
FLUID DATA
34 SP.VOL MIXTURE@RELIEVING PRESS. (ft3/lb)
35 SP. VOL [email protected] RELIEVING PRESS. (ft3/lb)
36 OPER. PRESS. (psig) SET PRESS. (psig) 145 270
37 OPER. TEMP. (°F) RELIEF TEMP. (°F) 38.2 142
38 SUPERIMPOSED BACK CONSTANT (psig) 14.7
39 PRESS VARIABLE (psig)
40 BUILT UP BACK PRESSURE (psig)
41 TOTAL BACK PRESSURE (psig) 14.7
42 %ALLOWABLE OVER PRESSURE 10
43 BAROMETRIC PRESSURE 14.7
44 WET. AREA(FOR VESSEL) (ft2) -
45 LATENT HEAT OF VAPOR (Btu/lb) -
46 CALC. AREA (in2) VTA
47 SELECTED AREA (in2) VTA
CALCULATION
48 ORIFICE DESIGNATION VTA
RESULT
49 VALVE RELIEF CAPACITY (lb/hr) VTA
50 MFR. MODEL NO. VTA
51 CAP (SCREWED / BOLTED) SCREWED
52 LEVER (PLAIN / PACKED) NO
53 OPTION TEST GAUGE NO
54 RUPTURE DISC NO
55 PAINTING NOTE 3
NOTE:
1. ALL INSTRUMENT SHALL BE TAGGED WITH 316 SS NAMEPLATE SHOWING TAG NO.
2. VENDOR SHALL BE REFER TO PT. ENERGASINDO HEKSA KARYA VENDOR LIST (AVL)
3. PAINTING SPECIFICATION REFER TO EHK-IKPP-PL-SPC-002 SPECIFICATION EXTERNAL PIPE COATING.
4. VTA = VENDOR TO ADVISE