HT870 User Manual

Download as pdf or txt
Download as pdf or txt
You are on page 1of 28

NARCO HT870

HANDHELD NAV/COM
960 CHANNELS
TABLE OF CONTENTS

1.1INTRODUCTION .................................................................... 1
2.1PRODUCT DESCRIPTION ............................................................. 1
3.1DESIGN FEATURES ................................................................. 1
4.1SPECIFICATIONS .................................................................. 2
5.1PRELIMINARY INSPECTION AND UNPACKING ............................................ 3
5.2HT870 AND SUPPLIED ACCESSORIES .................................................. 3
6.1HT870 MAINTENANCE INFORMATION ................................................... 4
7.1USE OF EXTERNAL MICROPHONE ...................................................... 4
8.1USE OF EXTERNAL HEADPHONES OR SPEAKER ........................................... 5
9.1HT870 LICENSE REQUIREMENTS ...................................................... 5
10.1 NICKEL CADMIUM (NiCad) BATTERY PACK SPECIFICATIONS................. 5
10.2 BATTERY PACK CHARGING.............................................. 6
10.3 BATTERY PACK INSTALLATION.......................................... 7
10.4 QUICK CHANGING THE BATTERY PACK TO PRESERVE MEMORY................. 7
10.5 OPTIONAL ALKALINE BATTERY PACK..................................... 7
11.1 ADDITIONAL ANTENNA CONSIDERATIONS.................................. 8
12.1 CAUTIONS TO OPERATORS.............................................. 8
13.1 DESCRIPTION AND LOCATION OF CONTROLS............................... 9
13.1.1 HT870 TOP PANEL DESCRIPTION........................................ 10
13.2 16-KEY KEYBOARD DESCRIPTION........................................ 10
13.3 PRODUCT DESCRIPTION HT870.......................................... 11
14.1 INTRODUCTION TO OPERATING PROCEDURES............................... 14
14.2 POWER TURN-ON AND VOLUME CONTROL................................... 15
14.3 SQUELCH CONTROL OPERATION.......................................... 15
14.4 FREQUENCY ENTRY.................................................... 16
14.5 FREQUENCY ASSIGNMENTS TO MEMORY.................................... 16
14.5.1 PROGRAMMING OF LOCATIONS M0 TO M9.................................. 16
14.5.2 RECALLING FREQUENCY FROM MEMORY LOCATION........................... 18
14.6 OPERATION OF THE HT870 AS A COM TRANSCEIVER........................ 18
14.6.1 FREQUENCY MODE OF OPERATION (COM CHANNELS)......................... 18
14.6.1.1 FREQUENCY MODE SINGLE FREQUENCY OPERATION.......................... 18
14.6.1.2 FREQUENCY MODE SCANNING............................................ 18
14.6.2 MEMORY MODE OF OPERATION........................................... 19
14.6.2.1 MEMORY LOCATION LOCKOUT............................................ 20
14.6.2.2 RESTORING A LOCKED OUT MEMORY LOCATION TO THE SCAN SEQUENCE........ 22
14.7 VOR NAV OPERATION.................................................. 22
14.7.1 CDI MODE........................................................... 22
14.7.1.1 SETTING THE OBS.................................................... 23
14.7.1.2 AUTO CENTERING..................................................... 23
14.7.1.3 BEARING MODE....................................................... 23
14.7.2 DUPLEX OPERATION IN NAV MODE....................................... 24

i
LIST OF ILLUSTRATIONS

13-1 HT870 CONTROL FUNCTIONS 9


13-2 MIC CONNECTOR PIN ASSIGNMENT 10
13-3 16-KEY KEYBOARD 10

ii
1.1 INTRODUCTION
This manual contains product description, features, specifications, available
options and operating instructions.
It is not intended as a maintenance manual, therefore, service information in
the form of theory, alignment or schematics is not provided.
2.1 PRODUCT DESCRIPTION

The Narco HT870 is a microprocessor controlled hand held 760 channel


communication transceiver covering the band of 118 to 136.975 MHz and a 200
channel NAV receiver covering the band of 108 to 117.95 MHz. The HT870
antenna is removable and may be connected to the aircraft's COM antenna.
Nav and COM frequencies are displayed on a liquid crystal display (LCD) and
are entered on an easy to use 16-key keyboard. Ten pre-programmable NAV or
COM frequencies may be stored in a non-volatile memory and manually selected
for use or automatically scanned. A memory lockout feature is provided in
which programmable frequencies can be locked out of the automatic or manual
scan.

The HT870 is powered by a rechargeable, quickly changed, NiCad battery pack.


An optional nonrechargeable alkaline battery pack for emergency use is
available. The user is alerted when the battery pack voltage has dropped
below its useable limit by the appearance of the letters "BATT" in the
display. The liquid crystal display can be illuminated to facilitate viewing
in darkness.
3.1 DESIGN FEATURES
Microprocessor controlled circuitry
760 COM channels
200 NAV channels
10 pre-programmable nonvolatile memory locations
Keyboard data entry
Large Liquid Crystal Display (LCD)
Quickly changed, rechargeable NiCad battery pack
Scanning Modes: Memory, Scan
Priority channel scanning in SCAN mode
Squelch-Adjust Control
Nominal 2 watts RF Transmitter
Lightweight, 1 lb. 4 oz. (570 grams)
Receiver sensitivity 1.5 microvolts for 6 dB S+N/N
Separate external speaker/microphone jack
Inputs for normal and quick charge
Quick removable (BNC) antenna
Quick slideoff battery pack
VOR displayed in CDI/BRG modes.

1
4.1 SPECIFICATIONS
GENERAL

Navigation channels: 200 (50 KHz steps) from 108.00 to 117.95 MHz
Communication channels: 760 (25 KHz steps) from 118.00 to 136.975 MHz
Memory Channels: 10 Channels
Weight: 1 lb. 4 oz (570 grams)
Dimensions: Width 2.44 in. (62 mm) Height 7.05 in. (179 mm)
Depth 1.54 in. (39 mm)
TRANSMITTER
Power: 1.5 watts carrier (minimum), 2 watts nominal
Frequency Stability: ±0.002%
Modulation: 6A3, 70% minimum
Frequency range: 118.00 to 136.975 MHz (760 channels)
Spurious radiation: -46 dB below carrier
Antenna impedance: 50 ohms
RECEIVER

Frequency range: NAV (108.00 to 117.95 MHz)


COM (118.00 to 136.975 MHz)
Audio output: 0.5 watts into 8 ohms (speaker)
30 milliwatts into 600 ohms (headphones)
Receiver sensitivity: 1.5 microvolts max for 6 dB S+N/N
Image rejection: 50 dB or greater
Receiver selectivity: 6 dB ±15 KHz, 60 dB ±30 KHz
Squelch Sensitivity: Adjustable carrier, AGC type

POWER SOURCE

9.6 Vdc, 600 mA, NiCad Battery


Battery full charge time: 150 mA maximum @ 5 hrs (using optional base
charger. Part Number 50906-0001)
45 mA maximum @ 17 hrs (using supplied wall charger)
Battery life per charge: Receive only: 8 hrs.
(Approximate) Transmit 10% duty: 4-6 hrs.
Transmit 30% duty: 2-4 hrs.
Number of battery recharges (full discharge to full charge): up to 300

TEMPERATURE
Operating range: -30 to +50 degrees C

2
5.1 PRELIMINARY INSPECTION AND UNPACKING
Upon receipt of the HT870, inspect the shipping container to attempt to
determine if equipment may have been damaged during shipment. Note damage, if
any.
Carefully unpack the unit and inspect it for any damage that may have occurred
during shipment. Refer to Sections 5.2 and 5.3 and inventory the contents of
your shipment.

5.2 HT870 AND SUPPLIED ACCESSORIES


An HT870 is ordered using part number 03117-0300. This part number is
comprised of the following items:
ITEM QTY DESCRIPTION
1 1 HT870 Handheld NAV/COM
2 1 NiCad rechargeable Battery Pack (Part No. 50900-0001)
3 1 Battery Wall Charger (Part No. 50901-0001)
4 1 Flexible Antenna (Part No. 50902-0001)
5 1 Operator's Manual (Part No. 03125-0621)
5.3 HT870 OPTIONAL ACCESSORIES
The following list comprises the available accessories for the HT870:

ITEM ORDER NUMBER DESCRIPTION


1 50900-0002 Nonrechargeable alkaline battery pack
2 50900-0001 Rechargeable NiCad battery pack (9.6 Vdc/500
maH)
3 50905-0001 Leather cowhide case with snap-off front flap,
build in belt clip.
4 50902-0001 Flexible rubberized antenna with BNC connector
5 50907-0001 Handheld remote combination speaker/microphone
complete with connector ready to use. No
adjustments necessary. For ground use only.
Not recommend for use in aircraft.
6 50932-0001 Mobile NiCad battery charger. Plugs into
cigarette lighter of aircraft or car, which
permits NiCad battery charging or operation of
the HT870.
7 50906-0001 Desktop quick charger and stand. The HT870 is
placed upright into a well in the stand which
permits the quick-charging (5 hrs.) of the
HT870's installed NiCad battery pack.

3
5.3 Continued
7 50906-0001 The HT870 may be operated in both
(Cont.) receive and transmit modes while it is charging,
but ONLY when a NiCad battery pack has been
installed.
8 50926-0101 6 inch adapter cable which permits the
interfacing of aircraft type headphones and
microphones to the HT870. One end of the cable
connects to the HT870's top panel external
speaker/microphone connector; installed on the
other end of the cable are standard headphone
and microphone jacks. An external push-to-talk
switch must be supplied and installed by the
owner to complete the interface.
9 50908-0001 External speaker/microphone connector only.
Mates to the HT870's top panel external
speaker/microphone connector. This connector is
used when the owner wishes to design and
fabricate his own interface adapter cable (see
item 8).

6.1 HT870 MAINTENANCE INFORMATION


The HT870 is not field repairable. Should a service problem arise, write a
note explaining the problem. Include in the note you name, shipping address,
and type of shipping desired (UPS, Federal Express, etc.) Include the note
with the HT870 and ship prepaid to:

NARCO AVIONICS, INC.


270 Commerce Drive
Fort Washington Industrial Park
Fort Washington, PA 19034

Attn: Factory Service Dept.

7.1 USE OF EXTERNAL MICROPHONE


The use of a good noise cancelling microphone is highly recommended when using
the HT870 in an aircraft environment. The HT870's internal microphone is
rendered inoperative when an external microphone that has been connected to
the top panel speaker/microphone connector and the Internal/External switch is
in the "E" position.

4
7.1 Continued
Any current popular aircraft microphone may be used; the only exception being
carbon microphones. They require more current than is available from the
HT870 and therefore would not perform adequately.
8.1 USE OF EXTERNAL HEADPHONES OR SPEAKER
The HT870's internal speaker is rendered inoperative when an external speaker
or headphones are connected to the HT870's top panel mic. jack. The
Internal/External switch must be in the "I/E" or "E" position. Headphone
impedance should be 600 ohms minimum, and speaker impedance should be 8 ohms.
9.1 HT870 LICENSE REQUIREMENTS
If the HT870 is to be used as an aircraft transceiver, the Federal
Communications Commission requires that FCC Form 404 titled "Application for
Aircraft Radio Station License" be submitted prior to operation.

If the HT870 is to be used as a ground station, the FCC Form 406 titled
"Application for Ground Station Authorization in the Aviation Services" must
be submitted prior to operation.
10.1 NICKEL CADMIUM (NiCad) BATTERY PACK SPECIFICATIONS

Nominal Operating Voltage: 9.6 Vdc

Nominal Capacity: 600 milliamp hour


"Fully Charged State" Output Voltage: 10.8 to 11.6 Vdc

"Discharged State" Output Voltage: 8 Vdc

Quick Charge: 150 mA max/5-6 hours for full charge


Standard Charge: 45 mA/16-17 hours for full charge

Advisable Temperature Ranges: Charging: 10 to 40 degrees C


Discharging: -30 to 60 degrees C
Storage (3 months): -30 to 50
degrees C

5
10.1 Continued
3 Months Storage Characteristics (battery fully charged and NOT
connected to HT870):
Storage Temperature: 0 degrees C (32 degrees F) 10 to 20 % drop
in battery capacity through self-
discharge
20 degrees C (59 degrees F) 30 to 40% drop in
battery capacity through self-
discharge
Note: At a storage temperature of 45 degrees C (113 degrees F),
after 1.5 months the battery capacity has dropped by 95%.
Battery Service Life: 300 charge/discharge cycles (minimum)

Memory Effect: NiCad batteries have a "memory effect", where the


battery voltage drops in 2 levels during operation
(discharge). The first level drop is approximately 8% reduction
in capacity for the first 30 to 40 minutes of operation followed
by a sharp 60% drop in capacity during the next 10-15 minutes of
operation. This "memory effect" is caused by repeatedly charging
the batteries when they have been only slightly discharged. This
is a temporary problem which can be rectified by performing 2 to 3
complete discharge/charge cycles.

10.2 BATTERY PACK CHARGING


CHARGING
CHARGING DEVICE CURRENT CHARGING TIME
Wall Charger (supplied 45 mA 16-17 hours for a
with HT870) (Standard full charge;
charge rate) however, charger may
be left on indefinitely
Optional Mobile Adapter 45 mA 15-16 hours for a
(cigarette lighter plug) full charge with
Note: Some mobile lighter radio turned OFF.
sockets are "off" if Radio may be
the ignition switch operated with
is "off". charger plugged in but
batteries will not charge
because charging current
is used by the radio.

Optional Desktop Quick ----- 1 hour with


Charger and stand radio turned off for
a full charge (See note).

6
10.2 Continued
Note: The HT870, when turned off, may be left on the quick charger
indefinitely without harm to the battery pack.
The HT870 may be operated both in the receive and transmit modes while being
charged in the Desktop quick charger/stand; however, the battery charging rate
drops back to the standard rate (17 hours) because a portion of the charging
current is used to power the radio.

10.3 BATTERY PACK INSTALLATION


To remove the Battery Pack, depress the Battery Lock button and slide it off
in the direction of the Lock Button. To install it, slide the Battery Pack
onto the bottom of the unit, ensuring the lock button clicks up.
CAUTION: Never store an HT870 with the NiCad battery pack connected.
There is internal circuitry that is always connected to the
battery bus that draws a small amount of current
(microamperes) which will deplete that battery's charge
within 3 weeks. Always store the HT870 with the battery
disconnected.

10.4 QUICK CHANGING THE BATTERY PACK TO PRESERVE MEMORY


If a battery pack that needs recharging is being replaced by a second fully
charged pack, the exchange must be completed within 30 seconds. Failure to do
so will result in the erasure of all operator selected frequencies stored in
memory (m0 to m9). Always turn the HT870's power switch OFF before installing
or removing a battery pack.
10.5 OPTIONAL ALKALINE BATTERY PACK

An optional nonrechargeable alkaline battery pack is available for the HT870


(see Section 5.3). This battery pack is an ideal choice for an emergency
back-up power source as it has a storage life of approximately 2 years. The
service life of the battery pack is approximately 20 hours when operating the
HT870 in the receive mode. Alkaline batteries may be changed within this
pack.
CAUTION: 1. DO NOT try to recharge the alkaline battery.
2. Never store an HT870 with the battery pack connected.
There is internal circuitry that is always connected
directly to the battery bus that draws a small amount
of current (microamperes) which will deplete the
battery over time. Always store the HT870 with the
battery disconnected. When batteries are changed with
a pack observe polarity.

7
11.1 ADDITIONAL ANTENNA CONSIDERATIONS
When the HT870 is operated in an aircraft environment, an improvement in both
COM and NAV performance will be realized if an aircraft type antenna is used
in place of the supplied flexible whip antenna. The flexible antenna is
quickly and easily removed as it incorporates a standard BNC connector. It is
recommended that a standard 50 ohm impedance aircraft COM antenna be used for
both the COM operation and VOR reception. VOR accuracy using an aircraft COM
antenna is superior to the VOR accuracy using the standard HT870 flexible
antenna which may vary as much as 5 degrees or more on local conditions. For
maximum VOR range and accuracy, an aircraft VOR antenna may be used; however,
it is not recommended that HT870 COM transmissions be made while using a VOR
antenna.
12.1 CAUTIONS TO OPERATORS
-Ensure that the battery pack is properly charged before
operating.

-Never operate the transmitter without an antenna installed.

-Turn the power switch OFF before installing or removing a


battery.
-Always change the battery pack in less than 30 seconds to
preserve the frequencies stored in memory.
-Never turn the power switch ON while the push-to-talk (PTT)
is pushed in.
-Never dispose of the NiCad battery pack in a fire.

-Never dissect a NiCad battery as they contain toxic


material.

-Never store (greater than 3 weeks) the HT870 with the


battery pack connected. Disconnect the battery pack.

-Be sure to observe polarity of alkaline batteries when


changed in the optional alkaline battery pack.

-Never try to recharge the alkaline battery back.

8
13.1 DESCRIPTION AND LOCATION OF CONTROLS

Figure 13-1 HT870 CONTROL FUNCTIONS

9
13.1.1 HT870 TOP PANEL DESCRIPTION

1. Microphone Input
2. Speaker Output
3. Push to Talk Switch
4. Ground
5. No Connection
6. No Connection

FIGURE 13-2 MIC CONNECTOR PIN ASSIGNMENT

13.2 16-KEY KEYBOARD DESCRIPTION

FIGURE 13-3 16-KEY KEYBOARD

The numbered keys are used to assign a frequency. The letters M0-M9 define 10
memory locations where assigned frequencies may be stored. These keys are
also used to recall or access these stored frequencies.

10
13.3 PRODUCT DESCRIPTION HT870
DESCRIPTION:

The HT870 is a hand held communications band Transceiver/navigation


receiver with VOR bearing or CDI Display. This unit is self contained with
its own speaker, microphone, push to talk switch and flexible antenna, or it
can be connected to external headset, microphone, and antenna.
OPERATION:

The operation of this unit is controlled by function switches located on


the periphery of the unit in conjunction with the 16 key keypad on the front
of the unit. Figure 13.1 illustrates the location of controls which is
accompanied by the following text.
1. Top Panel Controls

The top panel of the unit has 8 functions, labeled 1 through 8 in Fig.
13.1. Their functions are as follows:

1. Antenna Connector: This is a standard BNC connector which


connects to the flexible antenna supplied with the unit or can be
connected to an external antenna through RG58 or suitable coaxial
cable to an external antenna.
2. Squelch Control: This knob is used to set the desired squelch
level for speaker intelligibility, and should be set for quieting
with a no signal condition for maximum battery life.

3. Volume Control/Power Switch: This knob is used to turn the unit


on or off and to set the desired audio level for the internal
speaker or external headset.

4. Charge Jack: This connector is to be used with the wall charger


to charge the nicad battery pack.

5. External Connector: This connector is used to connect to the


optional external headset/microphone adapter cable.
6. CDI/BRG Switch: This is a momentary switch used to select the CDI
or BRG mode of display when a VOR channel is selected.

11
13.3 Continued
7. M-set Switch: This switch is used to activate the memory set
function. When depressed the memory set function is turned on and
information can be entered or changed in the 10 memory channels. In the
off mode the information in the memory can not be changed.
8. Internal/External Switch: This switch is a three position switch
used to select the speaker and microphone to be used with the unit.

1. Internal position (I) - In this position the internal or


built in speaker and microphone are used for operation.
2. Internal/External Position (I/E) - In this position the
internal microphone is operational but the audio is sent to
the external headset using the optional Headphone/Microphone
Adapter.

3. External Position (E) - In this position both the received


audio and microphone input to the unit are supplied through
the optional Headphone/Microphone Adapter.

*NOTE: In all positions of the Internal/External switch the PTT


switch on the side of the unit is active and can be used to
execute a transmit function if no external PTT switch is
available.

9. TX/Busy Led: This light will indicate when the channel being used
is busy or when the unit is being used for transmitting.

10. LCD Display: The separate sections of the LCD display are covered
in a separate explanation. See section 14.
11. Key Pad: This is a 16 key Keypad used for entering or recalling
data. The keypad is used in conjunction with the function
switches located on top of the radio. For ease of operation there
are no second function keys. The key functions are described
below:
A Key: This is the scan key and is used to activate the unit's two
scan functions.

1. Scan - by striking the scan key by itself the unit will scan
between the two limits set in upper limit stored in M0
and the lower limit assigned into the display prior to
scan start.

12
13.3 Continued
2. D Key followed by the A Key - by striking the Memory Key
then the Scan Key the unit will scan the 10 memory
channels. If a memory channel contains a frequency
which the user does not want to scan it can be locked
out and the unit will skip this channel in the memory
scan process.
B Key: This key is associated with the OBS/BRG Mode of operation
and operates in the following manner:
1. BRG Mode - If the B key is used while in the BRG mode the
bearing function will alternate cycle between the bearing TO
and bearing FROM the received VOR station each time the key
is struck.
2. CDI Mode - In the CDI mode of display the B key can be used
in three ways as follows:
a. Auto To - To set the OBS to the TO radial of the VOR
station you are receiving, strike the B key. At this
time the OBS display will blank and the TO/FR flag
will display the condition that had existed prior to
striking of the key. If this is the TO function just
strike the set key and the OBS will be set to the TO
radial of the VOR station; if the FR flag is being
displayed striking the B key again will cause the TO
flag to display and by striking the set key the OBS
will be set to the TO Radial of the VOR.

b. Auto FR - This is accomplished as explained in Auto TO


with the TO/FR description reversed.

c. Selecting a desired OBS Radial - To select an OBS to


be used for navigation purposes, just strike the B key
and key in a legal 1, 2, or 3 digit number completing
the entry by striking the set key. If 1 or 2 digit
entries are used the unit assumes leading zero's and
will fill them in for the user.

13
13.3 Continued
* Note the auto functions require a received signal i.e. the
TO/FR flag must be displayed in order to be utilized. If any
attempt is made to use Auto Function without a received signal the
unit will display the previous displayed OBS value when the set
key is struck.
C Key: This key is used in conjunction with frequency. If the C
Key is struck the Frequency display will blank and inserting
a valid 2, 3, 4, 5, or 6 digit number and striking the set
key will channel the radio to the new frequency. For ease
of operation the HT870 will accept a truncated version of
the desired frequency. For example, 228 "set" would be read
as 122.800 and 128 "set" would be read as 112.800, thereby
reducing the workload. If any time during entry a mistake
is made, it can be corrected by striking the C Key and
clearing the display. If the user wishes to cancel the
operation and keep his original frequency all that is
necessary is to strike the "set" key when the frequency
display is blank.

12. Keyboard Lock Switch: This switch is used to lock out inadvertent
key strokes that might happen in the normal handling or use of the
unit. When activated the 16 key keypad is disabled.
13. Push to Talk Switch (PTT): This switch is used to activate the
transmit function of the radio. If the unit is channeled to a
communication frequency the transmit and receive functions are on
the same frequency. If the unit is channeled to a navigation
frequency when the PTT switch is pressed the unit will transmit on
the duplex frequency 122.100 MHZ for FSS Communications.
14. LCD Illuminate Switch: This switch is used to light the LCD
display for viewing in the dark. The light will remain lit as
long as the switch is depressed.

14.1 INTRODUCTION TO OPERATING PROCEDURES


The HT870 may be utilized as a 760 channel COM Transceiver or a 200 channel
NAV Receiver/Converter. The unit may be operated in either the Memory or
Frequency Modes.

14
14.1 Continued
The Memory Mode allows for operation over 10 NAV or COM frequencies that are
operator chosen and stored in memory. Frequency scanning may be either Manual
or Automatic for COM frequencies but is limited to Manual only for NAV
frequencies.
The Frequency Mode allows for operation over all 760 COM channels or 200 NAV
channels. Frequency scanning may be either Manual or Automatic for COM
frequencies but is limited to a single frequency only for NAV frequencies.

NOTES:
1. If the letters "BATT" should appear in the upper right hand corner
of the display, the battery pack voltage has fallen below its
lowest operating limit. It should be fully recharged as soon as
possible. During the time that the "BATT" is displayed, the radio
may be capable of a few more transmissions. However, complete
discharge of the batteries is not recommended since it will
require the reprogramming of memory locations M0 to M9.
2. The Lock Key on the side of the unit above PTT key locks out the
16 Keypad functions and must be in the unlocked condition to use
any Keypad function. If the Key Lock is activated the frequency
display will contain the letters "LOCH" and the Lock Switch must
be pressed to deactivate the Lock Function.

14.2 POWER TURN-ON AND VOLUME CONTROL


Rotate the "VOL" knob, located on the top panel, in a clockwise direction past
the switch detent to turn the unit ON. Further clockwise rotation of the knob
will increase the audio level. Initially set the volume to 1/2 its range.
14.3 SQUELCH CONTROL OPERATION

The squelch control knob is located on the top panel and is manually set by
the operator. When the knob is rotated in a clockwise direction to its stop,
the squelch is in its full open position. Receiver noise should be heard and
the TX/BUSY LED on the front Panel should be annunciated. The squelch control
should be set to its optimum break point by slowly turning the knob counter
clockwise until the receiver noise is squelched and the TX/BUSY LED goes out.

15
14.3 Continued

CAUTION NOTE: If the unit is operated with the squelch "open", automatic
frequency scanning will not operate normally. This is because the unit
interprets the detected receiver noise as a valid received signal and "locks
on" the noise.

14.4 FREQUENCY ENTRY


To enter a new frequency the user will press the "C" Key and the Frequency
display will blank. At this time the new frequency can be entered by using
the numeric keys. The HT870 is capable of interpreting short hand entries of
frequencies by assuming the 1 of the 100 MHz and the trailing zero's if
desired. This means that a minimum of 3 numeric entries are required for
simple frequency entries. i.e:
228 "set" would be entered as 122.800
2282 "set" would be entered as 122.825
If the leading 1 digit is used, the 6 digit entry format should be used for
frequency.

Frequency entries can be cleared if a mistake is made by striking the "C" Key;
The frequency entry sequence can be terminated by striking the "C" Key while
the frequency display is blank, at which time the frequency being used will be
re-displayed.

14.5 FREQUENCY ASSIGNMENTS TO MEMORY

Ten pre-programmable COM or NAV frequencies may be stored in the HT870's


memory. These memory locations are identified on the Keyboard as letters M0
through M9.

When the battery pack is first installed, the microprocessor automatically


pre-programs locations M1 to M9 to 121.500 MHz, and location M0 to 136.975
MHz.

NOTE: Location M0 is special in that the frequency stored here determines the
upper Freq Mode scanning limit when scanning.

14.5.1 PROGRAMMING OF LOCATIONS M0 TO M9

The following sequence illustrates memory programming:


1. Clear the display of the letter "E" or "M" if one is present. To
clear an "E", depress any key. To clear an "M", depress "D" Key.

16
14.5.1 Continued
2. Assign a NAV or COM frequency (See Section 14.4).

3. Press the "M-SET" switch to the ON position to enable the "#" Key.
4. Depress the "#" Key. Confirm that the letters "MW" appear in the
display.
5. Depress that location key (M0 to M9) at which the frequency is to
be stored. When the key is depressed, the frequency is stored.
Confirm that when the location key is depressed that the letters
"MW" change to "M" (memory mode), and that a numeral corresponding
to the location number appears in the smaller display.
6. Depress "D" Key ("M" disappears from the LCD) to take the radio
out of the memory mode and put it in the frequency mode. Remember
you can only assign a frequency if the "M" legend is out.

7. Assign a frequency for the next memory location.

8. Keep repeating steps 4, 5, 6, and 7 until all the desired


locations are programmed.

9. Press "M-SET" switch to disable the "#" Key.


EXAMPLE: Store 135.525 MHz in memory location M1.

17
14.5.2 RECALLING FREQUENCY FROM MEMORY LOCATION
EXAMPLE: Recall memory location M6.

a.If the radio is not in the Memory Mode ("M" annunciated in LCD), then
depress "D" Key. Confirm LCD displays "M" (memory mode).
b.Depress "6" Key. Frequency and channel number are displayed in LCD.
14.6 OPERATION OF THE HT870 AS A COM TRANSCEIVER

14.6.1 FREQUENCY MODE OF OPERATION (COM CHANNELS)


The Frequency Mode of Operation permits transmission and reception over any of
760 COM channels or over selected bands. The operator may choose to receive
and transmit over a single channel or to automatically scan a chosen band of
frequencies.

14.6.1.1 FREQUENCY MODE SINGLE FREQUENCY OPERATION


If it is required only to receive and transmit over a single channel, then
follow this procedure:
1. Turn the radio ON and set the Volume control to the ½ position.

2. Push the M-SET and LOCK buttons to the OFF position.

3. Set the Squelch to the optimum point (See section 14.3).


4. Assign the chosen frequency (See Section 14.4). Reception and
transmission will be over the displayed frequency.
5. Depress the LOCK switch to the ON position to disable the
keyboard.

6. To transmit, Push the Push-To-Talk (PTT) switch and confirm that


the "TX/BUSY" LED is annunciated in the upper right corner of the
unit.
14.6.1.2 FREQUENCY MODE SCANNING

The operator must choose the upper and lower scan limits.
A. SELECTION OF THE FREQUENCY SCANNING LIMITS

The upper limit is that frequency which is stored in memory in


location M0. The microprocessor pre-programs

18
14.6.1.2 Continued
136.975 MHz into M0. The operator must re-program M0 to suit his
requirements (See Section 14.5.1). After selecting the upper
limit, the operator chooses the lower limit and assigns this
frequency in the display. To start an UP scan, press the "A" Key.
The upper limit (M0) MUST BE HIGHER than the lower limit or else
you CANNOT scan. The display will just blink the displayed lower
limit frequency.

14.6.2 MEMORY MODE OF OPERATION


There are four differences between the Memory Mode of Operation and the
Frequency Mode of Operation.
1. Reception and transmissions are possible only over those COM
frequencies stored in locations M0 to M9.
NOTE:Nav frequencies may also be stored in memory.

2. There are no lower or upper scan limits to set. Scanning is from


location M0 to M9 sequentially.

3. Memory Location Lockout: Locations M1 to M9 can be locked out of


the scanning sequence. Location M0 cannot be locked out.

4. PCS (Priority Channel Scanning): This feature is restricted to


the SCAN scanning mode and, in addition, only when the radio is in
the Memory Mode of Operation. The SCAN Mode of scanning has an
added feature called "Priority Channel Scanning". When the radio
locks onto a busy channel for 10 seconds and then resumes the
scan, the scan does not begin with the next memory channel in
sequence. The scan departs the normal sequence and shifts over to
location M1, the designated priority channel. If M1 is not
active, the scan jumps back in sequence starting with the next
location above the previously locked on location. However, if M1
is busy when it is scanned, then the radio will lock onto M1 and
stay locked on until the signal opens. Then scan then departs M1
and jumps back into sequence starting with the location next in
sequence from the previously locked on location.
The following sequence illustrates how to set up the radio for the Memory Mode
of operation:

1. Program the required COM frequencies into memory as outlined in


section 14.5.1.

19
14.6.2 Continued
2. If the radio is not in the Memory Mode then press the "D" Key.
Confirm appearance of "M" in the display. (The radio is now in
Memory Mode).
3. Depress the "A" Key. The radio is now UP scanning locations M0 to
M9.
4. To stop press either the "B" or "C" key.

5. To stop the scan at a particular location, press the appropriate


location key (M0-M9).

NOTES:
1. When the transmitter is operated (PTT switch depressed), scanning will
stop. When the PTT switch is released, scanning will resume after
approximately 3 seconds.

2. Before scan of the COM frequencies is initiated, lock-out any NAV


frequencies stored in memory as outlined in Section 14.6.2.1.
In order to provide the highest VOR Radial accuracy, reliable lock-on in
the scanning modes was sacrificed.

Reliable lock-on to NAV frequencies is achieved by pressing the memory


location key of the desired NAV channel which stops the scan at that
memory location.

14.6.2.1 MEMORY LOCATION LOCKOUT

The HT870 has a memory location lockout feature that allows one or all of the
locations M1 to M9 to be locked out of scanning. Location M0 cannot be locked
out as this location determines the upper frequency limit of scan. This
lockout feature pertains only to the Memory Mode of Operation. When a memory
location is locked out, that location is passed over in the sequential
scanning.

This feature will be chosen to be implemented by the operator when only a few
selected stored channels need to be scanned or one or more particular channels
are so busy that they interfere with the scanning of the other channels.

20
14.6.2.1 Continued
The following sequence illustrates the memory location lockout procedure:

1. Depress the "D" Key to switch to the Memory Mode of Operation.


Confirm that the letter "M" appears in the display.
2. Depress a memory location key (M1 to M9) to recall the location
that is to be locked out. Confirm that the channel numeral is
present in the display.

3. Engage M-SET switch down.


4. Depress the "B" Key. When the key is depressed, the channel is
locked out. Confirm the presence of the letter "L" (lockout) next
to the channel number in the display. The "L' signifies that this
channel is locked out.

5. If more locations are to be locked out, recall each location by


first depressing its key and then the "B" Key. Follow this
sequence until all desired locations are locked out.

6. Release the M-SET switch.

EXAMPLE: Lock out memory location M1. Stored in M1 is 135.525 MHz.

21
14.6.2.2 RESTORING A LOCKED OUT MEMORY LOCATION TO THE SCAN SEQUENCE
To restore a locked out channel to the scanning sequence:

1.If the radio is not in Memory Mode, then press "D" Key.
2.Depress the memory location key (M1-M9) to recall the channel to be
unlocked.
3.Depress M-SET switch.

4.Depress the "B" Key. Confirm that the letter "L" disappears from the
display signifying the return of this channel to the scanning
sequence.
5.Release M-SET switch.
6.Restore the scan direction.

14.7 VOR NAV OPERATION

The HT870 is capable of giving the user both CDI and Bearing modes of
operation.

14.7.1 CDI MODE

In the CDI Mode the Left/Right Indicator is an 11 bar display with each bar
having a 2 degree resolution.

In this mode the TO/FR legends act as the NAV flag and will indicate when a
valid signal is received. The TO or FR indication will be with respect to the
selected Radial or OBS setting.

22
14.7.1 Continued
To enter the CDI Mode, select a valid VOR channel and press the CDI/BRG mode
button on the top of the radio. At this time theLeft/Right display should
appear at the bottom of the display and the OBS legend should appear in the
display's upper left.
14.7.1.1 SETTING THE OBS
To set the OBS push the "B" Key and the OBS/BRG Display will blank. At this
time the desired (000-359) OBS setting can be made; if the set key is
depressed before the 3 digits are entered, leading zero's will be assumed.
14.7.1.2 AUTO CENTERING
1. Auto TO - To set the OBS to the TO radial of the VOR station you
are receiving, strike the B key. At this time the OBS display
will blank and the TO/FR flag will display the condition that had
existed prior to the striking of the key. If this is the TO
function just strike the set key and the OBS will be set to the TO
Radial of the VOR station; if the FR Flag is being displayed
striking the B Key again will cause the TO Flag to display and by
striking the set key the OBS will be set to the TO Radial of the
VOR.

2. Auto FR - This is accomplished as explained in Auto TO with the


TO/FR description reversed.

* Note the auto functions require a received signal i.e. the TO/FR
flag must be displayed in order to be utilized. If any attempt is
made to use Auto Function without a received signal the unit will
display the previous displayed OBS value when the set key is
struck.

14.7.1.3 BEARING MODE


To select the Bearing Mode of operation insure that a valid VOR Frequency has
been selected and depress the OBS/BRG Key on the top of the unit. When a
valid signal has been Received, the 3 digit display to the left of the
frequency display will give the bearing to or from the selected VOR. To
obtain the reciprocal bearing of that being displayed press the "B" Key, the
TO/FR and bearing will change to the reciprocal of that being displayed. Each
time the "B" Key is struck bearing TO/FR will alternate to the reciprocal of
the bearing being displayed.

23
14.7.2 DUPLEX OPERATION IN NAV MODE
The HT870 is capable of Duplex Mode of operation when a NAV channel has been
selected. This means that the unit will transmit on Flight Service Frequency
122.10 when the PTT switch is depressed, and will receive on the selected NAV
frequency.
Note: Since the receiver is shut down during transmit periods, this will cause
temporary interruption of NAV reception.

24

You might also like