Scribd
Upload
25 views2 pages

4DO IOM Module: 4 X 16A Digital Relay Outputs For Local or Remote Serial Connection To A JACE Controller

Uploaded by

Hilal Hazaa

Hilal

Copyright:

© All Rights Reserved
Download as PDF, TXT or read online from Scribd
Download as pdf or txt

4DO IOM Module: 4 X 16A Digital Relay Outputs For Local or Remote Serial Connection To A JACE Controller

Uploaded by

Hilal Hazaa
25 views2 pages
Hilal

Original Title

Untitled

Copyright

© © All Rights Reserved

Available Formats

PDF, TXT or read online from Scribd

Did you find this document useful?

Is this content inappropriate?

Hilal

Copyright:

© All Rights Reserved
Download as PDF, TXT or read online from Scribd
Download as pdf or txt
25 views2 pages

4DO IOM Module: 4 X 16A Digital Relay Outputs For Local or Remote Serial Connection To A JACE Controller

Uploaded by

Hilal Hazaa
Hilal

Copyright:

© All Rights Reserved
Download as PDF, TXT or read online from Scribd
Download as pdf or txt
You are on page 1/ 2

4DO IOM module

4 x 16A digital relay outputs for local or


remote serial connection to a JACE® controller

Overview
The IOM range of I/O modules are
designed for use as local I/O within
motor control cabinets or as remote I/O
connected via RS485 Modbus. Typical
applications include building automation
control systems.

The 4DO module provides 4 independent


250vac/16A rated digital relay output
channels each with change over contact
configuration. Each digital output has a
yellow LED which indicates the current
status of the connected device.

The IP20 rated module may be plugged


together with other IOM modules and fitted Key features
onto standard TS35 DIN rail or fitted directly ▪▪ DIN rail or direct mounting
onto a backplate using screw fixings. The ▪▪ 24v ac or dc power operation
cascadable design allows power and ▪▪ 4 digital outputs with change over contacts
2-wire RS485 Modbus communications to ▪▪ 16A resistive load with high inrush current
▪▪ RS485 2-wire Modbus open communications
connect through without any extra wiring. ▪▪ Easy address setting using rotary switches
▪▪ Bi-colour LED for module status information
Modbus address setting is by rotary ▪▪ Yellow LED output status indication
switches which are easily accessible ▪▪ Configurable output condition on comms failure
underneath the top cover. A bi-colour LED ▪▪ Presetable hours on and hours off counters
indicates the communications status. The
4DO module has one 2-wire RS485 port
supporting a Modbus communications
network connection to a JACE® controller.

Page 1/2
TridiumEuropeIOM4DODS_v4
Specifications
Digital output data:
▪▪ number of outputs 4
▪▪ rated switching voltage 250v ac
▪▪ rated / inrush current (resistive load) 16A / 80A (20mS)
▪▪ maximum power rating 4,000VA
▪▪ maximum total module current 32A
▪▪ electrical life expectancy at rated / 4A load 1 x 105 cycles / 7 x 105 cycles @ 23°C & resistive load
▪▪ mechanical life expectancy 30 x 106 cycles
▪▪ maximum switching frequency 6 min-1 at rated current; 1,200 min-1 at no load
▪▪ contact material AgSnO2
▪▪ isolation test voltage (coil to contact) 4 kV

IOM 4DO module


▪▪ output relay contact configuration channels 1,2,3 & 4: change over contacts

LED status indication:


▪▪ per digital output yellow: on or off
▪▪ module status bi-colour: red / green

Bus data:
▪▪ bus protocol Modbus RTU
▪▪ bus interface RS485, half duplex, non isolated
▪▪ bus topology multidrop
▪▪ bus length maximum 500m
▪▪ bus speed 19,200 bps
▪▪ bus line termination integrated termination resistor (220Ω); activate via jumper (default: off)
▪▪ bus protection built-in transient protection
▪▪ bus connector pluggable male & female integrated connectors (modules mounted with zero spacing)
▪▪ bus cabling Shielded Twisted Pair (STP)

General data:
▪▪ module power supply 20v to 28v ac or dc
▪▪ module current 250ma ac or 100ma dc
▪▪ operating temperature range 0°C to +50°C
▪▪ storage temperature range -20°C to +70°C
▪▪ CE marking Low voltage directive (LVD) 2006/95/EC according requirements of EN 50178
EMC directive 2004/108/EC according requirements of EN 55011 and EN 61326-1
▪▪ conductor cross section 0.2mm2 to 2.5mm2 screw clamp connection
▪▪ insulation stripping length 6mm
▪▪ mounting DIN-rail TS35 (35mm x 7.5mm) or direct mounting by M3 fixing
▪▪ installation position any
▪▪ assembly up to 15 in a row with zero spacing
▪▪ module size (l x w x h-TS35 / direct) 53mm x 95mm x 60mm / 58mm
▪▪ insulating material / flammability class Housing: Noryl. Terminals: Polyamid 6.6 V0 / UL94-V0
▪▪ protection degree (DIN 40050) IP 20
▪▪ installation guide for mounting and I/O wiring details please refer to the IOM Installation guide
▪▪ communications guide for Modbus communications details please refer to the IOM Module Communications guide

How to Order
Product
Code Description

IOMDOP 4 Digital Outputs (16A rated relays)

Copyright © 2013 Tridium. All rights reserved ®. Tridium, Niagara, NiagaraFramework, JACE and Security are trademarks or registered trademarks of Tridium.
Other marks are the properties of their respective owners. All specifications subject to change without notice or liability to provide changes to prior purchasers. Information
and specifications published here are current as of the date of publication of this document. Tridium reserves the right to change or modify specifications without prior notice.

Tridium Europe Ltd


1 The Grainstore, Brooks Green Road, Coolham, West Sussex, RH13 8GR, UK Page 2/2
Telephone: +44 (0) 1403 740290 www.tridiumeurope.com TridiumEuropeIOM4DODS_v4

You might also like