RENR5268-01

June 2004 FLUID POWER SYMBOLS

BASIC COMPONENT SYMBOLS

MAIN AUX.
PUMP: VARIABLE and
PUMP or MOTOR FLUID CONDITIONER SPRING CONTROL VALVES RESTRICTION LINE RESTRICTION 2-SECTION PUMP PRESSURE COMPENSATED
(FIXED)

VARIABILITY SPRING LINE RESTRICTION PRESSURE HYDRAULIC PNEUMATIC LINE RESTRICTION ATTACHMENT
(ADJUSTABLE) (VARIABLE) COMPENSATION ENERGY TRIANGLES VARIABLE and PRESSURE
COMPENSATED

VALVES
VALVE ENVELOPES VALVE PORTS

ONE POSITION TWO POSITION THREE POSITION TWO-WAY THREE-WAY FOUR-WAY

CONTROL VALVES CHECK VALVES

AB AB

P T P T
BASIC SPRING SHUTTLE PILOT
NORMAL POSITION SHIFTED POSITION INFINITE POSITION
SYMBOL LOADED CONTROLLED

MEASUREMENT ROTATING SHAFTS

PRESSURE TEMPERATURE FLOW UNIDIRECTIONAL BIDIRECTIONAL

FLUID STORAGE RESERVOIRS

D5N and D6N Track-Type Tractor

Hydraulic System VENTED PRESSURIZED RETURN ABOVE FLUID LEVEL

COMBINATION CONTROLS
RETURN BELOW FLUID LEVEL

AKD1-1134
AGG1-1334 SOLENOID SOLENOID SOLENOID SOLENOID and SERVO THERMAL DETENT
or MANUAL and PILOT PILOT or MANUAL
CFH1-0299
MANUAL CONTROL SYMBOLS
CKT1-0399
CBF1-0299
CCG1-0399 PUSH-PULL LEVER MANUAL SHUTOFF GENERAL MANUAL PUSH BUTTON PEDAL SPRING

ALH1-0734 RELEASED PRESSURE

PILOT CONTROL SYMBOLS
REMOTE SUPPLY PRESSURE
CBJ1-0399
ALR1-0634
EXTERNAL RETURN INTERNAL RETURN SIMPLIFIED COMPLETE INTERNAL
SUPPLY PRESSURE

ACCUMULATORS CROSSING AND JOINING LINES HYDRAULIC AND PNEUMATIC CYLINDERS

SPRING LOADED GAS CHARGED LINES CROSSING LINES JOINING SINGLE ACTING DOUBLE ACTING

HYDRAULIC PUMPS HYDRAULIC MOTORS INTERNAL PASSAGEWAYS

FIXED VARIABLE DISPLACEMENT FIXED VARIABLE DISPLACEMENT THREE TWO

INFINITE
DISPLACEMENT NON-COMPENSATED DISPLACEMENT NON-COMPENSATED POSITIONING POSITION POSITION

UNIDIRECTIONAL UNIDIRECTIONAL

FLOW IN ONE PARALLEL CROSS FLOW ALLOWED IN

BIDIRECTIONAL BIDIRECTIONAL DIRECTION FLOW FLOW EITHER DIRECTION

Finger Tip Control

© 2004 Caterpillar Printed in U.S.A.
All Rights Reserved

RENR5268-01
4 Page, DGM
 M
J
K
7

AA BB
8

6 Hydraulic System Components

Item Qty Description
4 Bank Valve Group (All Dozers with Ripper) or
1 1
3 Bank Valve Group
16 2 1 Inlet Manifold Cover Assembly
18 19 I 3 1 Dozer Lift Valve Group
11 4 1 Dozer Tilt Valve Group
5 1 Dozer Angle Valve Group (STD "VPAT" Blade)
16 6 1 Ripper Lift Valve Group
7 1 End Cover
18 19 I 8 2 Make-up Valve Group
9 2 Cylinder Group (Lift)
10 10 1 Cylinder Group (Tilt)
11 2 Cylinder Group (Angle STD "VPAT" Blade)
5 12 2 Cylinder Group (Ripper Lift)
13 1 Tank Group
14 1 Filter Element
15 1 Pump Group
12 16 2 Make-up Valve Group with Line Relief
Make-up Valve Group with Line Relief
17 1
(D6N Dozers with “SU” Blade or All Dozers with Ripper)
18 2 Plug (D6N Dozers with “SU” Blade)
19 2 Seal (D6N Dozers with “SU” Blade)
20 1 Case Drain Filter

B
A

D5N / D6N FTC Schematic

Item Description
4 C A Cylinder Bypass
B Rod End
C Head End
8 D Suction
E Pump Case Drain
F Implement Return
G Float Detent
17 15 H Pump Signal
I Ports Blocked on D6N when Using “SU” Blade
G N Line AA-BB Blocked for Power Beyond End Cover
J
Line AA-BB Open for Standard End Cover
K For Power Beyond Use 4T-7862 End Cover
L
3 L Load Sensing Signal Pressure Tap
M Implement Pump Discharge Pressure and SOS Tap Combination
N Case Drain Pressure

2
H 11

F 1
13

E
9
14
D
20

RENR5268-01
4 Page, B/W, DGM