CTS

DTR
SERIAL PIC PROGRAMMER CN1
DB-9 FEMALE R1 1.5K
1 C-GND Q1
6 BC547
Serial PIC Programmer kit is a must have for all those who develop, experiment, program and 2 R2 10K
play with Microchip based PIC projects. 7 RTS +
ZD1 C1

PGD
3 TXD
8 CTS D1 5.1V 100uF/25V
JDM compatible interface design
¦ 4 1N4148
DTR
ICSP and direct chip level programming available
¦ 9
5 C-GND
ZIF type socket for easy placement and removal of the microcontroller
¦
RTS PGC
LED indication of programming being done
¦
VDD
No power supply needed. May not work on laptops where the voltage may be below 7.3 V
¦ D2
1N4148 CN2
Zener Diode protected design
¦ SW1 ZIFSOC-20x2
9-Pin PCB mounted female type D connector provided for PC side connection
¦ SW ITCH 28-40 PIN
1 40
MCLR
Selector switch for selecting different PIC type during programming in ZIF socket
¦ CN3 8-18 PIN 2 39
3 38
Marker points provided on PCB for proper insertion point of different PIC's in the ZIF socket
¦ PIC ICSP
4 37
1 MCLR R4
Four mounting holes of 3.2 mm each
¦ MCLR D3 ZD2 R3 100 5 36
6 35
PCB dimensions 53 mm x 108 mm

PGM
¦ 2 PGC 1N4148 6.2V 1K
PGC 7 34
PGD 8 33
PGD 3 9 32
TXD Q2 R5 10K
BC547 10 31
GND 4 11 30
D4
PGM LED 12 29
PGM 5 13 28
Q3
VDD D5 BC557 14 27
VDD 6 15 26
1N4148
C3 16 25
+ 0.1uF 17 24
C2 18 23
100uF/25V SW2 19 22
SW 20 21
R6 J1
10K JUMPER

This is a Multichip PIC programmer using serial port. The programmer is a JDM Clone, SR. QTY. REF. DESC RIPTION
named after its Original developer Jens Dyekjar Madsen who devised this first. The 1 1 C N1 9 PIN D C ONNEC TOR - FEMALE
Programmer can program 8-pin to 40-pin devices using single ZIF socket as well as 2 1 C N2 40 PIN ZIF SOC KET
ICSP cable. ICSP option is available at Connector CN3 which is clearly marked for pin 3 1 C N3 6 PIN RELIMATE/BERG C ONNEC TOR
description. LED D4 Provides visual indication of programming taking place. This 4 2 C 1,C 2 100uF/25V
Programmer does not need any power supply. SW1 is a switch select for programming 5 1 C3 0.1uF
40-28 and 18-8 PIC Micros in the ZIF socket. Since the programming voltage is taken 6 4 D1,D2,D3,D5 1N4148
from the Serial Port of the Computer, it is recommended you check this voltage before 7 1 D4 RED LED
using it. Voltage at TxD, DTR and RTS should be ± 7.5V and above. Insertion position 8 1 J1 2 PIN JUMPER WITH C LOSER
of different PIC are clearly marked on the PCB if you wish to use the ZIF socket for 9 2 Q1,Q2 BC 547
programming. SW2 on the PCB selects the “VPP before VDD” option available for 10 1 Q3 BC 557
certain PIC micros with Internal OSC and MCLR chosen. Please check the datasheet of 11 1 R1 1.5K
the respective PIC you choose to program for this feature. Some popular 12 3 R2,R5,R6 10K
programming software used along with this programmer are IC-Prog of Bonny Gijzen 13 1 R3 1K
and WinPic800 available at http://www.winpic800.com. These are freely 14 1 R4 100E
downloadable from the net. 15 1 SW1 3 PIN SLIDE SWITC H
16 1 SW2 3 PIN BERG JUMPER WITH C LOSER
Please refer to the schematic diagram for the configuration of this board. 17 1 ZD1 5.1V ZENER
18 1 ZD2 6.2V ZENER
The kit includes all components required for the project accepts power supply, cabinet 19 9 JUMPER WIRE JUMPER
and Serial Port cable. Please check the components supplied to you as per the BOM
“Bill of Material” listed in this document.

0 7 0 0 5
www.twovolt.com www.youtube.com/thetwovolt Author Rajkumar Sharma www.koteq.com ©
www.twovolt.com
 0 7 0 0 5
www.twovolt.com www.youtube.com/thetwovolt Author Rajkumar Sharma www.koteq.com ©
www.twovolt.com