424QUIZ3

CIP Level 1—Quiz 3
1. It is the coating inspector’s job to record the minutes of the pre-job

meeting.
A. True
B. False
2. Goals of the pre-job meeting should include
I. review scope of work.

II. change orders.
III. review logistical support.
IV. reserve concerns for later.
A. I and II only
B. III and IV only
C. I, II, and III only
D. I, II, III, and IV only
3. The pre-job conference is usually requested by the
A. engineer.
B. owner.
C. inspector.
D. purchasing agent.
CIP Level 1 Quiz 3—August 2010 Page 1

4. Before the pre-job meeting, an inspector should NOT
I. visit the site.

II. read the MSDS.
III. read the standard.
IV. read the specification.
A. I and II only
B. III and IV only
C. I, II, and III only
D. I, II, III, and IV
5. After the pre-job meeting, an Inspector should NOT
A. review personal notes.

B. be the one recording the minutes of the meeting.
C. follow up with team members.
6. The inspector's logbook is typically a personal chronicle of what happens on

a daily basis and is not usually submitted to anyone else for review.
A. True
B. False
7. Which of the following is a significant advantage of airless spray compared

to conventional airspray?
A. Easily adjustable atomization of air

B. Easily adjustable pattern width
C. Faster production rate
D. Equipment easier to clean

8. At a minimum, inspection records should show all
I. environment conditions.
II. work process from pre-treatment through repairs.
III. subjective statements of contractor performance.
A. I, II, and III

B. I and II only
C. II and III only
D. I and III only
9. SSPC Technology Guide No. 12 addresses proper lighting of enclosures for

surface preparation and coating application.
A. True
B. False
10. Conventional spray works by forcing the coating material under very high
pressure through a very small hole (orifice).
A. True
B. False
11. If the desired DFT of a coating is 100 microns (4 mils), what wet film
thickness will be required if the coating contains 100% volume solids?
A. 50 microns (2 mils)
B. 75 microns (3 mils)
C. 100 microns (4 mils)
D. 150 microns (6 mils)

12. With conventional airspray equipment, dry spray may be caused by
A. no air pressure at the gun.

B. plugged fluid tip.
C. atomization pressure too high.
D. too much thinner added during mixing.
13. Most liquid coatings
A. may be applied by brush, roller, or spray.

B. must be applied by using conventional air spray.
C. must be applied by using airless spray.
D. must be applied be using air assisted airless spray.
14. Conventional air spray guns typically have integral adjustments for
A. air pressure from the compressor.

B. fan width and fluid flow.
C. size of the tip.
D. CFM of air required.
15. Fluid pressure in a conventional air spray fluid line is primarily controlled by
A. fluid outlet valve.

B. air pressure at the compressor.
C. adjusting the pot pressure regulator.
D. squeezing the hose.

16. Which items found on a product data sheet provide application

information?
I. Cure time
II. Profile
III. Tip size
IV. Recoat interval
A. I only
B. I and II only
C. I and III only
D. I, III, and IV
17. With the wet film thickness wheel, the diameter of the central wheel is
greater than the diameter of the outer wheels.
A. True
B. False
18. When using a WFT wheel, rotate the wheel across the film
I. 45%.
II. 90%.
III. 180%.
IV. 360%.
A. I or II only
B. II or III only
C. III or IV only
D. II or IV only

19. According to SSPC-PA2, the pencil pull-off gauge is classified as a Type 1B

magnetic pull-off gauge.
A. True
B. False
20. According to SSPC-PA 2, the preferred method to verify calibration of

magnetic DFT (Type 1) gauges is
A. using a sample of bare steel treated in the same way as the

steel.
B. using shims of a known thickness.
C. as defined by the manufacturer’s instructions of the specification.
D. using plastic shims.
21. Magnetic DFT instruments
A. can be used on non-ferrous substrates.

B. are affected by vibration.
C. are affected by air temperature.
D. are affected by substrate temperature.
22. Which items of information are generally found on product data sheets?
I. Solids by volume
II. VOC values
III. Chemical composition
A. I only
B. II only
C. I and II only

D. II and III only
23. Where will you find information such as ingredients, exposure limits, and
flammability classifications of coatings?
A. Application data sheets

B. Material safety data sheets
C. Product data sheets
D. Performance data sheets
24. __________ is a document/form containing data regarding the reactivity

and flammability properties of a particular substance.

25. _________ are intended to communicate technical facts related to specific

material and its application properties.


424QUIZ3

Uploaded by

Copyright:

Available Formats

424QUIZ3

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

424QUIZ3

Uploaded by

Copyright:

Available Formats

CIP Level 1—Quiz 3

1. It is the coating inspector’s job to record the minutes of the pre-job

2. Goals of the pre-job meeting should include

I. review scope of work.

3. The pre-job conference is usually requested by the

CIP Level 1 Quiz 3—August 2010 Page 1

4. Before the pre-job meeting, an inspector should NOT

I. visit the site.

5. After the pre-job meeting, an Inspector should NOT

A. review personal notes.

6. The inspector's logbook is typically a personal chronicle of what happens on

7. Which of the following is a significant advantage of airless spray compared

A. Easily adjustable atomization of air

CIP Level 1 Quiz 3—August 2010 Page 2

8. At a minimum, inspection records should show all

A. I, II, and III

9. SSPC Technology Guide No. 12 addresses proper lighting of enclosures for

CIP Level 1 Quiz 3—August 2010 Page 3

12. With conventional airspray equipment, dry spray may be caused by

A. no air pressure at the gun.

13. Most liquid coatings

A. may be applied by brush, roller, or spray.

A. air pressure from the compressor.

A. fluid outlet valve.

CIP Level 1 Quiz 3—August 2010 Page 4

16. Which items found on a product data sheet provide application

CIP Level 1 Quiz 3—August 2010 Page 5

19. According to SSPC-PA2, the pencil pull-off gauge is classified as a Type 1B

20. According to SSPC-PA 2, the preferred method to verify calibration of

A. using a sample of bare steel treated in the same way as the

21. Magnetic DFT instruments

A. can be used on non-ferrous substrates.

CIP Level 1 Quiz 3—August 2010 Page 6

D. II and III only

A. Application data sheets

24. __________ is a document/form containing data regarding the reactivity

A. Application data sheets

25. _________ are intended to communicate technical facts related to specific

A. Application data sheets

CIP Level 1 Quiz 3—August 2010 Page 7

You might also like