Scribd
Upload
80 views5 pages

TS Flash Writer Manual - Rev1.04

TOSHIBA

Uploaded by

taehyun Kim
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
80 views5 pages

TS Flash Writer Manual - Rev1.04

TOSHIBA

Uploaded by

taehyun Kim
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

TOSHIBA MCU FLASH WRITER INSTRUCTION MANUAL

TOSHIBA MCU FLASH WRITER

INSTRUCTION MANUAL

Jan 2008

T.S ELECTRONICS
Copyright ⓒ 2006 TS ELECTONICS CO., LTD
All Right Reserved

T.S ELECTRONICS
TOSHIBA MCU FLASH WRITER INSTRUCTION MANUAL

1. Package Contents
The TOSHIBA MCU FLASH WRITER contains the following items
● TOSHIBA MCU FLASH WRITER
● USB-to-USB CABLE
● TOSHIBA FLASH WRITER INSTRUCTION MANUAL (Short Form)
● INSTALL CD-ROM
● On-Board CABLE

1) TOSHIBA FLASH WRITER 2) USB-to-USB CABLE 3) On-Board CABLE


TOSHIBA Flash Writer Simple Manual

TOSHIBA FLASH WRITER

POWER SWITCH
CONNECTOR
For On-Board Writing USB CONNECTOR

RESET SWITCH

YAMAICHI SOCKET

OFF-BOARD WRITING

1. Install CP210x_Drivers.exe included on the CD-ROM


2. Make a connection between Flash Writer and PC with USB Cable.
3. Turn on Flash Writer and Execute TOSHIBA Flash Programmer.
4. If you want to make a reconnection between two devices,
Click RECONNECT Icon on Flash Programmer and Push the RESET SWITCH on Flash Writer.
Do not pull out the USB Cable when TOSHIBA Flash Programmer is running.

ON-BOARD WRITING

Target Board

1. Install CP210x_Drivers.exe included on the CD-ROM


2. Make a connection among Target Board and Flash Writer and PC with USB Cable.
3. Turn on Flash Writer and Execute TOSHIBA Flash Programmer.
4. If you want to make a reconnection among three devices,
Click RECONNECT Icon on Flash Programmer and Push the RESET SWITCH on Flash Writer.
Do not pull out the USB Cable when TOSHIBA Flash Programmer is running.

TS ELECTRONICS CO., LTD.

4) INSTRUCTION MANUAL 5) INSTALL CD-ROM

2. Software Setup
The following files are included on the CD-ROM
● TOSHIBA Flash Programmer (sw00fn5-zccuvxxx_en.exe)
● Driver installation utility (CP210x_ Drivers.exe)
● TOSHIBA Flash Programmer Manual (Kor,Eng)
● TOSHIBA MCU FLASH WRITER Instruction Manual

2-1. Install Windows Virtual COM Port Driver


To install the Windows Virtual COM Port Driver, run CP210x_Drivers.exe on the CD-ROM
COM Port properties for the device can be selected in the device manager
(COM Port Number, Baud Rate etc.)

2-2. Install TOSHIBA Flash Programmer


To install the TOSHIBA Flash Programmer, run sw00fn5-zccuvxxx_en.exe on the CD-ROM
If you want to know further information about the TOSHIBA Flash Programmer,
Please refer to the TOSHIBA Flash Programmer Manual on the CD-ROM

T.S ELECTRONICS
TOSHIBA MCU FLASH WRITER INSTRUCTION MANUAL

3. Hardware Setup
The TOSHIBA MCU FLASH WRITER is connected to a PC as shown in Figure 1 and Figure2

OFF-BOARD WRITING

1. Connect one end of the USB cable to a USB Port on the PC


2. Connect the other end of the USB cable to the USB connector on the TOSHIBA MCU FLASH WRITER

Figure 1. Hardware SETUP1

ON-BOARD WRITING

1. Connect one end of the USB cable to a USB Port on the PC


2. Connect the other end of the USB cable to the USB connector on the TOSHIBA MCU FLASH WRITER
3. Connect one end of the cable to the connector on the TOSHIBA MCU FLASH WRITER
4. Connect the other end of the cable to the connector on the TARGET BOARD

Target Board

Figure 2. Hardware SETUP2

T.S ELECTRONICS
TOSHIBA MCU FLASH WRITER INSTRUCTION MANUAL

4. Target Board
Refer to Figure 3 for the detail information about the TOSHIBA MCU FLASH WRITER

POWER SWITCH
On-Board
Connector USB CONNECTOR

RESET SWITCH

YAMAICHI SOCKET

Figure 3. TOSHIBA MCU FLASH WRITER

4-1. Universal Serial Bus (USB) Interface (T1)


A USB Connector is provided to facilitate connections to the USB interface on the FLASH WRITER
See Table 1 for the USB pin definitions.

Pin# Description
1 VBUS

2 D-

3 D+

4 GND

Table1. USB Connector Pin Descriptions

T.S ELECTRONICS
TOSHIBA MCU FLASH WRITER INSTRUCTION MANUAL

4-2. On-Board Connector (T2)


A On-Board Connector is provided to connections to the Target Board for On-Board Writing
See Table 2 for the On-Board Connector pin definitions.

Pin# Signal Description


1 VDD +5V
2 TEST Test pin for serial mode

3 TX TxD output
4 RX RxD input

5 RST RESET signal input

6 GND 0V

7 GND 0V
8 GND 0V

Table2. On-Board Connector Pin Descriptions

4-3. Actual Image

T.S ELECTRONICS

You might also like