Hydrogen
Hydrogen
Hydrogen
Properties
Combustion
0:29
Combustion of hydrogen with the oxygen in the air. When the bottom cap is removed, allowing air to enter at
the bottom, the hydrogen in the container rises out of top and burns as it mixes with the air.
The Space Shuttle Main Engine burnt hydrogen with oxygen, producing a nearly invisible flame at full thrust.
Spin isomers
Main article: Spin isomers of hydrogen
Molecular H2 exists as two spin isomers, i.e. compounds that differ only in the spin states of their
nuclei.[29] In the orthohydrogen form, the spins of the two nuclei are parallel, forming a
spin triplet state having a total molecular spin ; in the parahydrogen form the spins are
antiparallel and form a spin singlet state having spin . The equilibrium ratio of ortho- to para-
hydrogen depends on temperature. At room temperature or warmer, equilibrium hydrogen gas
contains about 25% of the para form and 75% of the ortho form.[30] The ortho form is an excited
state, having higher energy than the para form by 1.455 kJ/mol,[31] and it converts to the para
form over the course of several minutes when cooled to low temperature.[32] The thermal
properties of the forms differ because they differ in their allowed rotational quantum states,
resulting in different thermal properties such as the heat capacity.[33]
The ortho-to-para ratio in H2 is an important consideration in the liquefaction and storage of liquid
hydrogen: the conversion from ortho to para is exothermic and produces enough heat to
evaporate a most of the liquid if not converted first to parahydrogen during the cooling process.
[34]
Catalysts for the ortho-para interconversion, such as ferric oxide and activated
carbon compounds, are used during hydrogen cooling to avoid this loss of liquid.[35]
Phases
Hydrogen gas is colorless and transparent, here contained in a glass ampoule.
Phase diagram of hydrogen. The temperature and pressure scales are logarithmic, so one unit
corresponds to a 10× change. The left edge corresponds to 105 Pa, which is about atmospheric
pressure.[image reference needed]
Gaseous hydrogen
Liquid hydrogen
Slush hydrogen
Solid hydrogen
Metallic hydrogen
Plasma hydrogen
Compounds
Further information: Category:Hydrogen compounds
Covalent and organic compounds
While H2 is not very reactive under standard conditions, it does form compounds with most
elements. Hydrogen can form compounds with elements that are more electronegative, such
as halogens (F, Cl, Br, I), or oxygen; in these compounds hydrogen takes on a partial positive
charge.[36] When bonded to a more electronegative element, particularly fluorine, oxygen,
or nitrogen, hydrogen can participate in a form of medium-strength noncovalent bonding with
another electronegative element with a lone pair, a phenomenon called hydrogen bonding that is
critical to the stability of many biological molecules.[37][38] Hydrogen also forms compounds with
less electronegative elements, such as metals and metalloids, where it takes on a partial
negative charge. These compounds are often known as hydrides.[39]
Hydrogen forms a vast array of compounds with carbon called the hydrocarbons, and an even
vaster array with heteroatoms that, because of their general association with living things, are
called organic compounds.[40] The study of their properties is known as organic chemistry[41] and
their study in the context of living organisms is known as biochemistry.[42] By some definitions,
"organic" compounds are only required to contain carbon. However, most of them also contain
hydrogen, and because it is the carbon-hydrogen bond that gives this class of compounds most
of its particular chemical characteristics, carbon-hydrogen bonds are required in some
definitions of the word "organic" in chemistry.[40] Millions of hydrocarbons are known, and they are
usually formed by complicated pathways that seldom involve elemental hydrogen.
Hydrogen is highly soluble in many rare earth and transition metals[43] and is soluble in both
nanocrystalline and amorphous metals.[44] Hydrogen solubility in metals is influenced by local
distortions or impurities in the crystal lattice.[45] These properties may be useful when hydrogen is
purified by passage through hot palladium disks, but the gas's high solubility is a metallurgical
problem, contributing to the embrittlement of many metals,[16] complicating the design of pipelines
and storage tanks.[46]
Hydrides
Main article: Hydride
Compounds of hydrogen are often called hydrides, a term that is used fairly loosely. The term
"hydride" suggests that the H atom has acquired a negative or anionic character, denoted H−,
and is used when hydrogen forms a compound with a more electropositive element. The
existence of the hydride anion, suggested by Gilbert N. Lewis in 1916 for group 1 and 2 salt-like
hydrides, was demonstrated by Moers in 1920 by the electrolysis of molten lithium hydride (LiH),
producing a stoichiometric quantity of hydrogen at the anode.[47] For hydrides other than group 1
and 2 metals, the term is quite misleading, considering the low electronegativity of hydrogen. An
exception in group 2 hydrides is BeH2, which is polymeric. In lithium aluminium hydride,
the [AlH4]− anion carries hydridic centers firmly attached to the Al(III).
Although hydrides can be formed with almost all main-group elements, the number and
combination of possible compounds varies widely; for example, more than 100 binary borane
hydrides are known, but only one binary aluminium hydride.[48] Binary indium hydride has not yet
been identified, although larger complexes exist.[49]
In inorganic chemistry, hydrides can also serve as bridging ligands that link two metal centers in
a coordination complex. This function is particularly common in group 13 elements, especially
in boranes (boron hydrides) and aluminium complexes, as well as in clustered carboranes.[50]
Protons and acids
Further information: Acid–base reaction
Oxidation of hydrogen removes its electron and gives H+, which contains no electrons and
a nucleus which is usually composed of one proton. That is why H+ is often called a proton. This
species is central to discussion of acids. Under the Brønsted–Lowry acid–base theory, acids are
proton donors, while bases are proton acceptors.
A bare proton, H+, cannot exist in solution or in ionic crystals because of its unstoppable
attraction to other atoms or molecules with electrons. Except at the high temperatures
associated with plasmas, such protons cannot be removed from the electron clouds of atoms
and molecules, and will remain attached to them. However, the term 'proton' is sometimes used
loosely and metaphorically to refer to positively charged or cationic hydrogen attached to other
species in this fashion, and as such is denoted "H+" without any implication that any single
protons exist freely as a species.
To avoid the implication of the naked "solvated proton" in solution, acidic aqueous solutions are
sometimes considered to contain a less unlikely fictitious species, termed the "hydronium ion"
([H3O]+). However, even in this case, such solvated hydrogen cations are more realistically
conceived as being organized into clusters that form species closer to [H9O4]+.[51] Other oxonium
ions are found when water is in acidic solution with other solvents.[52]
Although exotic on Earth, one of the most common ions in the universe is the H+3 ion, known
as protonated molecular hydrogen or the trihydrogen cation.[53]
Isotopes
Main article: Isotopes of hydrogen
1
H is the most common hydrogen isotope, with an abundance of more than 99.98%.
Because the nucleus of this isotope consists of only a single proton, it is given the
descriptive but rarely used formal name protium.[56] It is unique among all stable
isotopes in having no neutrons; see diproton for a discussion of why others do not
exist.
2
H is known as tritium and contains one proton and two neutrons in its nucleus. It is
radioactive, decaying into helium-3 through beta decay with a half-life of 12.32
years.[50] It is so radioactive that it can be used in luminous paint, making it useful in
such things as watches. The glass prevents the small amount of radiation from
getting out.[59] Small amounts of tritium are produced naturally by the interaction of
cosmic rays with atmospheric gases; tritium has also been released during nuclear
weapons tests.[60] It is used in nuclear fusion reactions,[61] as a tracer in isotope
geochemistry,[62] and in specialized self-powered lighting devices.[63] Tritium has also
been used in chemical and biological labeling experiments as a radiolabel.[64]
Unique among the elements, distinct names are assigned to its isotopes in common use today.
During the early study of radioactivity, various heavy radioactive isotopes were given their own
names, but such names are no longer used, except for deuterium and tritium. The symbols D
and T (instead of 2
H and 3
H) are sometimes used for deuterium and tritium, but the symbol P is already in use
for phosphorus and thus is not available for protium.[65] In its nomenclatural guidelines,
the International Union of Pure and Applied Chemistry (IUPAC) allows any of D, T, 2
H, and 3
H to be used, although 2
H and 3
H are preferred.[66]
The exotic atom muonium (symbol Mu), composed of an antimuon and an electron, can also be
considered a light radioisotope of hydrogen.[67] Because muons decay with lifetime 2.2 µs,
muonium is too unstable to exhibit observable chemistry.[68] Nevertheless, muonium compounds
are important test cases for quantum simulation, due to the mass difference between the
antimuon and the proton,[69] and IUPAC nomenclature incorporates such hypothetical
compounds as muonium chloride (MuCl) and sodium muonide (NaMu), analogous to hydrogen
chloride and sodium hydride respectively.[70]
History
Discovery and use
Main article: Timeline of hydrogen technologies
In 1671, Robert Boyle discovered and described the reaction between iron filings and
dilute acids, which results in the production of hydrogen gas.[73][74]
Having provided a saline spirit [hydrochloric acid], which by an uncommon way of preparation
was made exceeding sharp and piercing, we put into a vial, capable of containing three or four
ounces of water, a convenient quantity of filings of steel, which were not such as are commonly
sold in shops to Chymists and Apothecaries, (those being usually not free enough from rust) but
such as I had a while before caus'd to be purposely fil'd off from a piece of good steel. This
metalline powder being moistn'd in the viol with a little of the menstruum, was afterwards
drench'd with more; whereupon the mixture grew very hot, and belch'd up copious and stinking
fumes; which whether they consisted altogether of the volatile sulphur of the Mars [iron?], or of
metalline steams participating of a sulphureous nature, and join'd with the saline exhalations of
the menstruum, is not necessary to be here discuss'd. But whencesoever this stinking smoak
proceeded, so inflammable it was, that upon the approach of a lighted candle to it, it would
readily enough take fire, and burn with a blewish and somewhat greenish flame at the mouth of
the viol for a good while together; and that, though with little light, yet with more strength than
one would easily suspect.
— Robert Boyle, Tracts written by the Honourable Robert Boyle containing new experiments,
touching the relation betwixt flame and air...
In 1766, Henry Cavendish was the first to recognize hydrogen gas as a discrete substance, by
naming the gas from a metal-acid reaction "inflammable air". He speculated that "inflammable
air" was in fact identical to the hypothetical substance called "phlogiston"[75][76] and further finding
in 1781 that the gas produces water when burned. He is usually given credit for the discovery of
hydrogen as an element.[5][6] In 1783, Antoine Lavoisier gave the element the name hydrogen
(from the Greek ὑδρο- hydro meaning "water" and -γενής genes meaning "former")[77] when he
and Laplace reproduced Cavendish's finding that water is produced when hydrogen is burned.[6]
Antoine-Laurent de Lavoisier
Lavoisier produced hydrogen for his experiments on mass conservation by reacting a flux of
steam with metallic iron through an incandescent iron tube heated in a fire. Anaerobic oxidation
of iron by the protons of water at high temperature can be schematically represented by the set
of following reactions:
1) Fe + H2O → FeO + H2
2) Fe + 3 H2O → Fe2O3 + 3 H2
3) Fe + 4 H2O → Fe3O4 + 4 H2
Many metals such as zirconium undergo a similar reaction with water leading to the
production of hydrogen.
Hydrogen was liquefied for the first time by James Dewar in 1898 by
using regenerative cooling and his invention, the vacuum flask.[6] He produced solid
hydrogen the next year.[6] Deuterium was discovered in December 1931 by Harold
Urey, and tritium was prepared in 1934 by Ernest Rutherford, Mark Oliphant,
and Paul Harteck.[5] Heavy water, which consists of deuterium in the place of regular
hydrogen, was discovered by Urey's group in 1932.[6] François Isaac de Rivaz built
the first de Rivaz engine, an internal combustion engine powered by a mixture of
hydrogen and oxygen in 1806. Edward Daniel Clarke invented the hydrogen gas
blowpipe in 1819. The Döbereiner's lamp and limelight were invented in 1823.[6]
The first hydrogen-filled balloon was invented by Jacques Charles in 1783.
[6]
Hydrogen provided the lift for the first reliable form of air-travel following the 1852
invention of the first hydrogen-lifted airship by Henri Giffard.[6] German
count Ferdinand von Zeppelin promoted the idea of rigid airships lifted by hydrogen
that later were called Zeppelins; the first of which had its maiden flight in 1900.
[6]
Regularly scheduled flights started in 1910 and by the outbreak of World War I in
August 1914, they had carried 35,000 passengers without a serious incident.
Hydrogen-lifted airships were used as observation platforms and bombers during
the war.
The first non-stop transatlantic crossing was made by the British airship R34 in
1919. Regular passenger service resumed in the 1920s and the discovery
of helium reserves in the United States promised increased safety, but the U.S.
government refused to sell the gas for this purpose. Therefore, H2 was used in
the Hindenburg airship, which was destroyed in a midair fire over New Jersey on 6
May 1937.[6] The incident was broadcast live on radio and filmed. Ignition of leaking
hydrogen is widely assumed to be the cause, but later investigations pointed to the
ignition of the aluminized fabric coating by static electricity. But the damage to
hydrogen's reputation as a lifting gas was already done and commercial hydrogen
airship travel ceased. Hydrogen is still used, in preference to non-flammable but
more expensive helium, as a lifting gas for weather balloons.
In the same year, the first hydrogen-cooled turbogenerator went into service with
gaseous hydrogen as a coolant in the rotor and the stator in 1937 at Dayton, Ohio,
by the Dayton Power & Light Co.;[78] because of the thermal conductivity and very
low viscosity of hydrogen gas, thus lower drag than air, this is the most common
type in its field today for large generators (typically 60 MW and bigger; smaller
generators are usually air-cooled).
The nickel hydrogen battery was used for the first time in 1977 aboard the U.S.
Navy's Navigation technology satellite-2 (NTS-2).[79] For example, the ISS,[80] Mars
Odyssey[81] and the Mars Global Surveyor[82] are equipped with nickel-hydrogen
batteries. In the dark part of its orbit, the Hubble Space Telescope is also powered
by nickel-hydrogen batteries, which were finally replaced in May 2009,[83] more than
19 years after launch and 13 years beyond their design life.[84]
Hydrogen emission spectrum lines in the visible range. These are the four visible lines of
the Balmer series.
Because of its simple atomic structure, consisting only of a proton and an electron,
the hydrogen atom, together with the spectrum of light produced from it or absorbed
by it, has been central to the development of the theory of atomic structure.
[85]
Furthermore, study of the corresponding simplicity of the hydrogen molecule and
the corresponding cation H+2 brought understanding of the nature of the chemical
bond, which followed shortly after the quantum mechanical treatment of the
hydrogen atom had been developed in the mid-1920s.
One of the first quantum effects to be explicitly noticed (but not understood at the
time) was a Maxwell observation involving hydrogen, half a century before
full quantum mechanical theory arrived. Maxwell observed that the specific heat
capacity of H2 unaccountably departs from that of a diatomic gas below room
temperature and begins to increasingly resemble that of a monatomic gas at
cryogenic temperatures. According to quantum theory, this behavior arises from the
spacing of the (quantized) rotational energy levels, which are particularly wide-
spaced in H2 because of its low mass. These widely spaced levels inhibit equal
partition of heat energy into rotational motion in hydrogen at low temperatures.
Diatomic gases composed of heavier atoms do not have such widely spaced levels
and do not exhibit the same effect.[86]
Antihydrogen (
H
) is the antimatter counterpart to hydrogen. It consists of an antiproton with
a positron. Antihydrogen is the only type of antimatter atom to have been produced
as of 2015.[87][88]
Cosmic prevalence and distribution
States
Throughout the universe, hydrogen is mostly found in the atomic and plasma states,
with properties quite distinct from those of molecular hydrogen. As a plasma,
hydrogen's electron and proton are not bound together, resulting in very high
electrical conductivity and high emissivity (producing the light from the Sun and
other stars). The charged particles are highly influenced by magnetic and electric
fields. For example, in the solar wind they interact with the
Earth's magnetosphere giving rise to Birkeland currents and the aurora.
Hydrogen is found in the neutral atomic state in the interstellar medium because the
atoms seldom collide and combine. They are the source of the 21-cm hydrogen
line at 1420 MHz that is detected in order to probe primordial hydrogen.[91] The large
amount of neutral hydrogen found in the damped Lyman-alpha systems is thought
to dominate the cosmological baryonic density of the universe up to
a redshift of z = 4.[92]
Under ordinary conditions on Earth, elemental hydrogen exists as the diatomic
gas, H2. Hydrogen gas is very rare in the Earth's atmosphere (around 0.53 ppm on a
molar basis[93]) because of its light weight, which enables it to escape from the
atmosphere more rapidly than heavier gases. However, hydrogen is the third most
abundant element on the Earth's surface,[94] mostly in the form of chemical
compounds such as hydrocarbons and water.[50]
A molecular form called protonated molecular hydrogen (H+3) is found in the
interstellar medium, where it is generated by ionization of molecular hydrogen
from cosmic rays. This ion has also been observed in the upper atmosphere of the
planet Jupiter. The ion is relatively stable in the environment of outer space due to
the low temperature and density. H+3 is one of the most abundant ions in the
universe, and it plays a notable role in the chemistry of the interstellar medium.
[95]
Neutral triatomic hydrogen H3 can exist only in an excited form and is unstable.
[96]
By contrast, the positive hydrogen molecular ion (H+2) is a rare molecule in the
universe.
Production
Main article: Hydrogen production
H2 is produced in chemistry and biology laboratories, often as a by-product of other
reactions; in industry for the hydrogenation of unsaturated substrates; and in nature
as a means of expelling reducing equivalents in biochemical reactions.
Water electrolysis
Metal-acid
Many metals react with water to produce H2, but the
rate of hydrogen evolution depends on the metal, the
pH, and the presence alloying agents. Most commonly,
hydrogen evolution is induced by acids. The alkali and
alkaline earth metals, aluminium, zinc, manganese,
and iron react readily with aqueous acids. This reaction
is the basis of the Kipp's apparatus, which once was
used as a laboratory gas source:
Zn + 2 H+ → Zn2+ + H2
In the absence of acid, the evolution of H2 is
slower. Because iron is widely used structural
material, its anaerobic corrosion is of technological
significance:
Fe + 2 H2O → Fe(OH)2 + H2
Many metals, such as aluminium, are slow to
react with water because they form passivated
coatings of oxides. An alloy of aluminium
and gallium, however, does react with water.
[121]
At high pH, aluminium can produce H2:
2 Al + 6 H2O + 2 OH− → 2 [Al(OH)4]− + 3 H2
Some metal-containing compounds react
with acids to evolve H2. Under anaerobic
conditions, ferrous hydroxide (Fe(OH)
2) can be oxidized by the protons of water
Thermochemical
More than 200 thermochemical cycles
can be used for water splitting. Many
of these cycles such as the iron oxide
cycle, cerium(IV) oxide–cerium(III)
oxide cycle, zinc zinc-oxide
cycle, sulfur-iodine cycle, copper-
chlorine cycle and hybrid sulfur
cycle have been evaluated for their
commercial potential to produce
hydrogen and oxygen from water and
heat without using electricity.[122] A
number of laboratories (including
in France, Germany, Greece, Japan,
and the United States) are developing
thermochemical methods to produce
hydrogen from solar energy and
water.[123]
Serpentinization reaction
In deep geological conditions
prevailing far away from the Earth's
atmosphere, hydrogen (H2) is
produced during the process
of serpentinization. In this process,
water protons (H+) are reduced by
ferrous (Fe2+) ions provided
by fayalite (Fe2SiO4). The reaction
forms magnetite (Fe3O4), quartz (SiO2),
and hydrogen (H2):[124][125]
3 Fe2SiO4 + 2 H2O → 2 Fe3O4 + 3 SiO2 + 2 H2
fayalite + water → magnetite + quartz + hydrogen
This reaction closely
resembles the Schikorr
reaction observed in
anaerobic oxidation of ferrous
hydroxide in contact with
water.
Applications
Petrochemical
industry
Large quantities of H2 are
used in the "upgrading" of
fossil fuels. Key consumers
of H2 include hydrodealkylatio
n, hydrodesulfurization,
and hydrocracking. Many of
these reactions can be
classified as hydrogenolysis,
i.e., the cleavage of bonds to
carbon. Illustrative is the
separation of sulfur from liquid
fossil fuels:
R2S + 2 H2 → H2S + 2 RH
Hydrogenation
Hydrogenation, the
addition of H2 to various
substrates is conducted
on a large scale. The
hydrogenation of N2 to
produce ammonia by
the Haber–Bosch
process consumes a few
percent of the energy
budget in the entire
industry. The resulting
ammonia is used to
supply the majority of the
protein consumed by
humans.[126] Hydrogenatio
n is used to
convert unsaturated
fats and oils to saturated
fats and oils. The major
application is the
production
of margarine. Methanol is
produced by
hydrogenation of carbon
dioxide. It is similarly the
source of hydrogen in the
manufacture
of hydrochloric acid. H2 is
also used as a reducing
agent for the conversion
of some ores to the
metals.[127]
Coolant
Main article: Hydrogen-
cooled turbo generator
Hydrogen is commonly
used in power stations as
a coolant in generators
due to a number of
favorable properties that
are a direct result of its
light diatomic molecules.
These include
low density, low viscosity,
and the highest specific
heat and thermal
conductivity of all gases.
Energy carrier
See also: Hydrogen
economy, Hydrogen
infrastructure,
and Hydrogen fuel
Elemental hydrogen has
been widely discussed in
the context of energy, as
a possible future carrier of
energy on an economy-
wide scale.[128] Hydrogen is
a ''carrier'' of energy
rather than an energy
resource, because there
is no naturally occurring
source of hydrogen in
useful quantities.[129]
Hydrogen can be burned
to produce heat or
combined with oxygen
in fuel cells to generate
electricity directly, with
water being the only
emissions at the point of
usage. The overall
lifecycle emissions of
hydrogen depend on how
it is produced. Nearly all
of the world's current
supply of hydrogen is
created from fossil fuels.
[130][131]
The main method
is steam methane
reforming, in which
hydrogen is produced
from a chemical reaction
between steam
and methane, the main
component of natural gas.
Producing one tonne of
hydrogen through this
process emits 6.6–9.3
tonnes of carbon dioxide.
[132]
While carbon capture
and storage can remove a
large fraction of these
emissions, the overall
carbon footprint of
hydrogen from natural
gas is difficult to assess
as of 2021, in part
because of emissions
created in the production
of the natural gas itself.[133]
Electricity can be used to
split water molecules,
producing sustainable
hydrogen provided the
electricity was generated
sustainably. However,
this electrolysis process is
currently more expensive
than creating hydrogen
from methane and the
efficiency of energy
conversion is inherently
low.[134] Hydrogen can be
produced when there is a
surplus of variable
renewable electricity, then
stored and used to
generate heat or to re-
generate electricity.[135] It
can be further
transformed into synthetic
fuels such
as ammonia and methano
l.[136]
Innovation in hydrogen
electrolysers could make
large-scale production of
hydrogen from electricity
more cost-competitive.
[137]
There is potential for
hydrogen to play a
significant role in
decarbonising energy
systems because in
certain sectors, replacing
fossil fuels with direct use
of electricity would be
very difficult.[134] Hydrogen
fuel can produce the
intense heat required for
industrial production of
steel, cement, glass, and
chemicals. For
steelmaking, hydrogen
can function as a clean
energy carrier and
simultaneously as a low-
carbon catalyst replacing
coal-derived coke.[138] Hydr
ogen used in
transportation would burn
relatively cleanly, with
some NOx emissions,[139] b
ut without carbon
emissions.[140] Disadvantag
es of hydrogen as an
energy carrier include
high costs of storage and
distribution due to
hydrogen's explosivity, its
large volume compared to
other fuels, and its
tendency to make pipes
brittle.[133] The
infrastructure costs
associated with full
conversion to a hydrogen
economy would be
substantial.[141]
Semiconductor
industry
Hydrogen is employed to
saturate broken
("dangling") bonds
of amorphous
silicon and amorphous
carbon that helps
stabilizing material
properties.[142] It is also a
potential electron donor in
various oxide materials,
including ZnO,[143][144] SnO2,
CdO, MgO,[145] ZrO2, HfO2,
La2O3, Y2O3, TiO2, SrTiO3,
LaAlO3, SiO2, Al2O3, ZrSiO
4, HfSiO4, and SrZrO3.
[146]
Aerospace
Liquid
hydrogen and liquid
oxygen together serve
as cryogenic fuel in liquid-
propellant rockets, as in
the Space Shuttle main
engines.
Niche and
evolving uses
Shielding
gas: Hydroge
n is used as
a shielding
gas in welding
methods such
as atomic
hydrogen
welding.[147][148]
Cryogenic
research: Liq
uid H2 is used
in cryogenic r
esearch,
including supe
rconductivity s
tudies.[149]
Buoyant
lifting: Becau
se H2 is lighter
than air,
having only
7% of the
density of air,
it was once
widely used
as a lifting
gas in
balloons
and airships.
[150]
Leak
detection: Pu
re or mixed
with nitrogen
(sometimes
called forming
gas),
hydrogen is
a tracer
gas for detecti
on of minute
leaks.
Applications
can be found
in the
automotive,
chemical,
power
generation,
aerospace,
and
telecommunic
ations
industries.[151]
Hydrogen is
an authorized
food additive
(E 949) that
allows food
package leak
testing, as
well as having
anti-oxidizing
properties.[152]
Neutron
moderation:
Deuterium (hy
drogen-2) is
used
in nuclear
fission
applications a
s
a moderator t
o
slow neutrons
.
Nuclear
fusion
fuel: Deuteriu
m is used
in nuclear
fusion reactio
ns.[6]
Isotopic
labeling: Deu
terium
compounds
have
applications in
chemistry and
biology in
studies
of isotope
effects on
reaction rates.
[153]
Rocket
propellant: N
ASA has
investigated
the use
of rocket
propellant ma
de from
atomic
hydrogen,
boron or
carbon that is
frozen into
solid
molecular
hydrogen
particles that
are
suspended in
liquid helium.
Upon
warming, the
mixture
vaporizes to
allow the
atomic
species to
recombine,
heating the
mixture to
high
temperature.
[154]
Tritium
uses: Tritium
(hydrogen-3),
produced
in nuclear
reactors, is
used in the
production
of hydrogen
bombs,[155] as
an isotopic
label in the
biosciences,[64]
and as a
source of beta
radiation in ra
dioluminescen
t paint for
instrument
dials and
emergency
signage.[59]
Biological
reactions
Further
information: Biohydrogen
and Biological hydrogen
production (Algae)
H2 is a product of some
types of anaerobic
metabolism and is
produced by
several microorganisms,
usually via
reactions catalyzed by iro
n- or nickel-
containing enzymes calle
d hydrogenases. These
enzymes catalyze the
reversible redox reaction
between H2 and its
component two protons
and two electrons.
Creation of hydrogen gas
occurs in the transfer of
reducing equivalents,
produced
during pyruvate fermentati
on, to water.[156] The
natural cycle of hydrogen
production and
consumption by
organisms is called
the hydrogen cycle.
[157]
Bacteria such
as Mycobacterium
smegmatis can utilize the
small amount of hydrogen
in the atmosphere as a
source of energy when
other sources are lacking,
using a hydrogenase with
samll channels that
exclude oxygen and so
permits the reaction to
occur even though the
hydrogen concentration is
very low and the oxygen
concentration is as in
normal air.[93][158]
Hydrogen is the most
abundant element in the
human body in terms of
numbers of atoms of the
element but the third most
abundant element by
mass. H2 occurs in the
breath of humans due to
the metabolic activity of
hydrogenase-containing
microorganisms in
the large intestine and is
a natural component
of flatus. The
concentration in the
breath of fasting people at
rest is typically less than
5 parts per million (ppm)
but can be 50 ppm when
people with intestinal
disorders consume
molecules they cannot
absorb during
diagnostic hydrogen
breath tests.[159]
Water splitting, in which
water is decomposed into
its component protons,
electrons, and oxygen,
occurs in the light
reactions in
all photosynthetic organis
ms. Some such
organisms, including the
alga Chlamydomonas
reinhardtii and cyanobact
eria, have evolved a
second step in the dark
reactions in which protons
and electrons are reduced
to form H2 gas by
specialized hydrogenases
in the chloroplast.
[160]
Efforts have been
undertaken to genetically
modify cyanobacterial
hydrogenases to
efficiently
synthesize H2 gas even in
the presence of oxygen.
[161]
Efforts have also been
undertaken with
genetically modified alga
in a bioreactor.[162]
Safety and
precautions
Main article: Hydrogen
safety
Hydrogen
Hazards
GHS labelling:
Pictograms
Hazard H220
statements
Precautionary P202, P210, P271, P377
statements
NFPA
704 (fire diamond)
0
4
0
Hydrogen poses a
number of hazards to
human safety, from
potential detonations and
fires when mixed with air
to being an asphyxiant in
its pure, oxygen-free
form.[164] In addition, liquid
hydrogen is
a cryogen and presents
dangers (such
as frostbite) associated
with very cold liquids.
[165]
Hydrogen dissolves in
many metals and in
addition to leaking out,
may have adverse effects
on them, such
as hydrogen
embrittlement,[166] leading
to cracks and explosions.
[167]
Hydrogen gas leaking
into external air may
spontaneously ignite.
Moreover, hydrogen fire,
while being extremely hot,
is almost invisible, and
thus can lead to
accidental burns.[168]
Even interpreting the
hydrogen data (including
safety data) is
confounded by a number
of phenomena. Many
physical and chemical
properties of hydrogen
depend on
the parahydrogen/orthohy
drogen ratio (it often takes
days or weeks at a given
temperature to reach the
equilibrium ratio, for which
the data is usually given).
Hydrogen detonation
parameters, such as
critical detonation
pressure and
temperature, strongly
depend on the container
geometry.[164]