IMIPLAST are APP modified bitumen reinforced roofing and waterproofing membranes for

general waterproofing applications.

DESCRIPTION
IMIPLAST membranes are made by saturating and coating a reinforcement core with a
homogeneous thermoplastic blend of APP (atactic polypropylene), distilled bitumen and
stabilizers. The mixture is carefully produced under controlled conditions to ensure its thermal
stability at high temperatures and flexibility at low temperatures.
IMIPLAST membranes are impermeable to water & easy to apply.

QUALITY ASSURANCE & MATERIAL WARRANTY

Imperbit Membrane Industries’ Management system is registered to ISO 9001 standards & all
IMIPLAST membranes carry a 10 year material warranty. In addition to stringent regular test
by IMI laboratory, our products are also tested periodically by independent laboratories.

SURFACE FINISH AND SIZE OF ROLL

The top surface of the membrane is covered with a thin layer of PE film or fine sand. The bottom
surface is covered with printed IMI design film.
The membrane are produced in thickness of 2, 2.6, 3, 4 & 5 mm and in a standard length of 10
mtrs and 1 mtr width.

REINFORCEMENT
A variety of reinforcement cores are used in the production of the IMIPLAST range, these
include 180 gr./m ², 200 gr./m ² & 250 gr./m ² spun bond polyester, fiberglass tissue and a
combination of the two.

USES
IMIPLAST – DPC/Basesheet membranes are ideal for general use in civil construction as a
damp-proof layer or as a base sheet under cap sheets in exposed or inverted roofing systems.
IMIPLAST-DPC are available in thickness of 2.0mm, 2.6mm & 3.0mm reinforced with 60 gr./m ²
GLASS FIBRE TISSUE.

IMIPLAST membranes are ideal for general use in single or multi-layer systems. They may be
used in low slope concrete roofs, balconies, multi storey car parks, for lining sewerage canals,
sub-grade structures and any concrete or cemented flat surface that needs waterproofing.

IMIPLAST - DR (DOUBLE REINFORCE MEMBRANES) are used for large roof decks where
dimensional stability of the membrane is important. The combination of polyester and fibre glass
tissue reinforcements ensures superior shape and dimensional stability under severe cyclic
conditions.

IMIPLAST – 250 membranes are recommended for heavy duty applications.

TOOLS FOR FIXING THE MEMBRANE

Gas torch for welding, related cylinder, knife for trimming the membrane, a trowel with a
rounded tip, marking aids and gloves.

APPLICATION
The surface to be waterproofed must be completely cleaned and free of dust, oil, protruding
nibs, nails etc. A coat of IMI Concrete Primer is then applied to the concrete surface at the rate
of 200 – 300 gr/m². The primer must be allowed to dry completely before fixing the membrane.
IMIPLAST waterproofing membranes are fixed by torch welding the underside. The membrane
rolls are lined up and spread open over the area to which they are to be fixed, starting at the
lowest point on a roof-deck. The rolls are laid so that they overlap each other by at least 10cms
along the side lap, lap-joints should shed water towards drains. The membranes are then rolled
back without changing the given orientation. They are then unrolled once again while heating
the underside sufficiently to cause surface melting. End laps should be a minimum 15 cms. Avoid
excessive and uneven application of heat. The lap joints should be heated from the top to
produce a thin bead of molten bitumen at the seam; the bead is then smoothened out with the
trowel, ensuring a properly welded joint.

EXPOSED ROOFING SYSTEM

For exposed application, skirting and flashings, IMIPLAST membranes are used. These are
produced with a self-protecting layer of natural or colored slate flakes. The membranes are
provided with a selvedge 10 cms wide that is granule-free. This facilities the forming of lap
joints. End of roll joints are made by scraping off 15cm of mineral flakes or heating 15 cms of the
mineral surface sufficiently to press-in the slate and expose the bitumen. The next roll is then
torched to the bitumen of the exposed area.
 ‡ TECHNICAL DATA FOR IMIPLAST RANGE

Properties IMIPLAST IMIPLAST- IMIPLAST IMIPLAST IMIPLAST IMIPLAST Method of Testing

DPC/Base 4F 200 DR 250
sheet
Reinforcement core 60 gr./m² 60 180 200 180 gr./m2 250 UEAtc MOAT
Glass fibre gr./m² gr./m² gr./m2 Polyester + gr./m² 31: Para F
tissue Glass Polyester polyester 60 gr./m2 Polyester
fibre Glass fibre
tissue tissue
Nominal thickness of membrane 2.0,2.6 & 3 4 3, 4 & 5 4&5 4&5 4&5 UEAtc ,
ASTM D 5147
Tensile Strength Longitudinal 300 400 800 900 880 1000
UEAtc
N/5cm Transversal 200 200 500 700 620 850
Tensile Strength Longitudinal 4 6 14 17 16 18
ASTM D 5147
kN/m Transversal 3 4 9 12 10 15
Longitudinal 3 3 40 40 40 45 UEAtc ,
Elongation %
Transversal 3 3 45 45 42 50 ASTM D 5147
Tear Strength (N) Longitudinal 150 200 450 550 480 550
Notch Method ASTM D 5147
Transversal 100 150 300 440 350 450
Puncture resistance (N) 250 300 800 900 880 1000 ASTM E 154
Resistance to Hydrostatic DIN 1048,
>4 bar(>40M) >7 bar(>70M)
pressure ASTM D 5385
Flexibility at low temperature -2 °C UEAtc
Softening Point * 155° C UEAtc, ASTM D 36
Penetration @25° C * 20 dmm UEAtc, ASTM D 5
Heat resistance @ 100°C No flow UEAtc
Water absorption @ 24 hrs. < 0.2 % ASTM D570
* Compound Properties (Tested during manufacturing process)
The technical data given here are the average results of tests HANDLING PRECAUTIONS: IMIPLAST membranes have no
carried out in our laboratory on the IMIPLAST membrane. IMI health hazard when used with our standard application
reserves the right to change or modify the data without prior recommendations. Unrolling of membrane at low temperature do
notice. All reasonable care has been taken in compiling the data not bang the rolls, unroll them carefully without kicking them. IMI
that to the best of our knowledge is accurate and true. All CONCRETE primer contains a flammable solvent with flash point of
recommendations are made in good faith. IMIPLAST membranes 420C. Use primer in well ventilated areas away from sources of
are warranted to be free from manufacturing defects for a period direct heat or ignition. Inhalation must be avoided and the use of
of 10 years. No responsibility can be accepted by us and no protective clothing, rubber gloves, goggles and barrier cream is
warranty is implied with regard to any of the recommendations recommended. Do not use solvent to clean skin. After work clean
made in this data sheet, since the conditions of actual use and the hands with soap and warm water or suitable mild detergent.
labour involved are beyond our control. IMIPLAST membranes Obtain immediate medical advice if redness or skin irritation
are not affected by chlorides, sulphates & phosphates as well as appears. In case of mouth or eye contact, flush immediately with
dilute acids found in ground water. fresh water and seek medical advice.
Packing Configuration: Storage:
2F-PBS/33 rolls per pallet Rolls must be kept up right at all times, in a covered well-
2.6F- PBS/28 rolls per pallet ventilated storage area, away from sources of direct heat. Heat
3P-PBS/SAND 28 rolls per pallet can cause progressive losing of their flexibility. If ambient
4P/F-PBS/SAND/DR 23 rolls per pallet temperatures at storage site fall below 150C, the rolls should be
4P MINERAL 20 rolls per pallet exposed to warmer temperatures of 150C to 400C for periods of
5P-PBS/MINERAL/DR 16 rolls per pallet upto 2 hours prior to use to facilitate unrolling of the membranes
to avoid cracking. During summer if the membrane left long time
Nominal roll length for above products = 10 mtrs
in the sun can quickly heat and reach temperature of 850C which
For IMIPLAST DPC- 20 rolls per pallet and 20 mtrs length
can cause progressive blackening of mineral granules on the rolls.
Indicative Loading Capacity for 4mm thickness: If stacking is necessary, ensure that rigid sheet of plywood is
552 Rolls per 40 ft Trailer / 468 Rolls per 20 ft Container placed between the pallets. Do not stack more than 2 high.
Product generic name: IMIPLAST membrane has a shelf life of 12 months from the date
APP XM-2F/2.6F-PBS of production, if stored in a cool, dry store in original unopened
APP XM-3P-PBS/SAND packing.
APP XM-4P/F-PBS/SAND
APP XM-4P/F-MINERAL
APP XM-5P-PBS/MINERAL

IMPERBIT MEMBRANE INDUSTRIES L.L.C.

P O BOX 33150, DUBAI, U.A.E.
TEL : (+9714) 880 1616
FAX: (+9714) 880 1661
E-MAIL : [email protected]
FACTORY: KM 3, JEBEL ALI - HATTA HIGHWAY, JEBEL ALI INDUSTRIAL 3.
‡ This technical data sheet supersedes all previous publications pertaining to this product IMIPLAST
Code: QC-DSM-15
Implementation Date: 28 April, 2015
Ed-06