6-4. Abestos Roofing

6-4.
ABESTOS ROOFING
Unlike galvanized iron roofing sheet where accessories from gutter down to the
smallest anchor straps are made on site out from the standard size of plain G.I. sheet
estimating asbestos roofing material is much simpler because all the roof accessories and
parts to be used such as gutter, ridge, hip and valley rolls are all factory made ready for
installation.
Different Kinds of Asbestos Roofing
1. Standard corrugated sheet

2. 4-V Corrugated sheet
3. Placa Romana
4. Kanaletas
5. Tencor corrugated sheet
6. Ardex lightweight corrugated sheet
A. Staandard Ardex
B. Super Ardex
Estimating Procedures:
A.) The number of corrugated asbestos roofing required is determined by dividing the gutter
length by the effective width of one sheet.
B.) In finding the number of accessories sush as flashing, gutter, ridge, hip and volley roll,
divide each total length by the effective length of the accesorries.
C.) Other parts such as ridge end cap, apron flashing, gutter corner, down spout and fittings
are found by direct counting. They are made according to factory standard sizes.
ILLUSTRATION. 6-7
From figure 6-9, find the standard asbestos roofing sheet

Including its accessories required.
A. STANDARD CORRUGATED ASBESTOS SHEET
FIGURE. 6-9 STANDARD ASBESTOS CORRUGATED SHEET

SOLUTION
Standard Sheet
1. Find the total length of the gutter. 2 x 26 = 52.00 meters
2. Refer the table 6-8. Divide 52.00 m. by the effective width
52.00 m.
= 62 pieces standard asbestos sheet.
0.838
GUTTER
Total length of the ridge roll is = 26.00 m. Refer to table 6-8, divide this length by the
effective length of one gutter.
2 x 26.00
= 22.26 pieces.
2.336
RIDGE ROLL
Total length of the ridge is = 26.00 meters. Refer to table 6-8 for ridge roll.
DIVIDE:
26.00 m
= 31.0 pcs. Ridge roll
.838
FLASHING
1. Find the total length of the flashing ( see figure )
3.00 m. x 4 sides = 12.00 meters
2. Refer to table 6-8, for outside flashing, divide:
12.00 m
= 5.25 say 6 pcs. Outside flashing.
2.286
RIDGE END CAP
1. From Figure 6-9. By actual count, there are 2 ridge end cap Order 2 pieces.
Summary of Materials
62 pcs. 1.20 x 3.00. standard corrugated sheet

23 pcs. Standard gutter
31 pcs. Standard ridge roll
6 pcs. Standard flashing
2 pcs. Standard ridge end cap
TECHNICAL DATA FOR ESTIMATING ASBESTOS ROOFING
TABLE 6-8 STANDARD CORRUGATED SHEETS
Length - 1.20 x 3.00 m.

End lapping Below 20 degrees - 0.30 m.
Above 20 degrees - 0.15 m.
Effective width - 0.838 m.
Ridge roll effective length - 0.838 m.
Gutter effective length - 2.336 m.
Outside flashing - 1.676 m.
FIGURE 6-10 STANDARD CORRUGATES SHEET
B. 4-V CORRUGATED ASBESTOS SHEET
TABLE 6-9 CORRUGATED SHEET TECHNICAL DATA
Standard Length - 2,438 m.

Ridge Roll effective length - 0.865 m.
Outside flashing effective length - 2.286 m.
FIGURE 6-11 4-V CORRUGATED ASBESTOS SHEET
C.TENCOR
TABLE 6-10 TENCOR CORRUGATED SHEET TECHNICAL DATA
Standard length - 2.44 m.

Lapping - 15 or 30 m.
Effective Length - 2.29 or 2.14 m.
Standard Width - 0.748 m.
Effective Width - 0.675 m.
Outside flashing - 1.50 to 3.00 m.
Minus Lapping - 0.15 m.
Ridge Roll - 0.953 m.
FIGURE 6-12 TENCOR CORRUGATED SHEET
D.KANALETAS
TABLE 6-11 KANALETAS TECHNICAL DATA
Length - 7.315 m.
Eaves flashing - 0.885 m.
Outside flashing effective length - 2.40 to 3.00 m.
FIGURE. 6-13 KANALETAS
E. ARDEX
TABLE 6-12 ARDEX TECHNICAL DATA
Standard width 0.52 m 0.105 m.

Effective width. 0.45 m. 0.97 m.
Nominal length 0.75 to 3.15 m. 2.40 to 3.60 m.
Ridge roll effective length 0.95 m. 0.95 m.
Outside flashing 1.50 to 2.00 m. 1.50 to 3.00 m.
Side lapping 0.15 m. 0.15 m.
FIGURE 6-14 ARDEX.
E. PLACA ROMANA
TABLE 6-13 PLACA ROMANA TECHNICAL DATA
Standard length - 0.912 m.

Effective length - 0.600 m.
Standard width - 1.180 m.
End lap - 0.200 m.
Side lap - 0.080 m.
Ridge roll effective length - 1.100 m.
Outside flashing effective length - 1.100 m.
Eaves flashing effective length - 1.100 m.
FIGURE6-15 PLACA ROMANA
6-5 COLORBOND LIP-LOK
Colorbond is a corrosion resistant zinc coated steel sjeet pre-painted steel ribbed tray
roofing and walling with the following special features.
1. Concealed fastening
2. Lock action rib design
3. Attractive fluted trays
4. Near flat roof slopes
5. Less supports-wider spaced
6. Strong lightweight steel
7. Custom cut long lengths
FIGURE 6-16 COLORBOND KLIP LOK

TABLE 6-14 COLORBOND KLIP LOK TECHNICAL DATA
Steel base thickness - 0.60 mm.

Total coated thickness - 0.63 mm.
Weight per meter length of panel - 6.00 M.
Length available up to - 15.00 m.
Longer length special order up to - 35.00 M.
Overall width - 0.427 m.
Effective width coverage - 0.406 m.
RECOMMENDED FASTENERS
(TWO FASTENERS REQUIRED PER CLIP)
Support member Normal Fastening Fastening over insulation

Up to 100 mm (4”)
Steel up to 3/32” to 3/16 No. 10 - 16 x 5/8 wafer head No. 10 - 15 x 7/8(22 mm)
2.5 - 5 mm thick self drilling and tapping crew wafer head self drilling and
tapping screw
Steel 3/32” to 3/16 No. 10 - 24 x 5/8 wafer head No. 10 - 24 x 7/8(22 mm)
2.5 - 5 mm thick self drilling and tapping crew wafer head self drilling and
tapping screw
Steel over 3/16 (5 mm thick) No. 10 - 24 x 5/8 wafer head No. 10 - 24 x 7/8 (22 mm)
thread cutting screw. Drill hole for No. 10 - 24 x 7/8”
4.5 mm Wafer head self drilling and
tapping crew.
2”x9G(50x 3.75 mm)counter 1

sunk head G.I spiral nail or 2 2 x9G(50 x 3.75
Hardwood No. 10 -12 x 1” (25mm) type mm)counter sunk head G.I
17 wafer head self drilling spiral nail or No. 10 -12 x 1
wood screw. 3
(45mm) type 17 wafer
4
head self drilling wood
screw.
3 No. 10 - 12 x 1/3/4 “
Softwood No. 10 - 12 x 1 “ type 17 (45 mm) type 17 wafer head
4
wafer head self drilling wood self drilling wood screw
screw
6-6 BANAWE HORIZONTAL METAL TILE
TABLE 6-15 BANAWE METAL TILE TECHNICAL DATA
ITEM LENGTH IN METER
Normal width 0.228 m.

Effective width coverage 0.204 m.
Length 12.19 m.
Minimum roof shape 15 degrees
FIGURE 6-17 CROSS SECTION OF BANAWE METAL TILE

6-4. Abestos Roofing

Uploaded by

Copyright:

Available Formats

6-4. Abestos Roofing

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

6-4. Abestos Roofing

Uploaded by

Copyright:

Available Formats

6-4.

Different Kinds of Asbestos Roofing

1. Standard corrugated sheet

From figure 6-9, find the standard asbestos roofing sheet

A. STANDARD CORRUGATED ASBESTOS SHEET

FIGURE. 6-9 STANDARD ASBESTOS CORRUGATED SHEET

1. Find the total length of the gutter. 2 x 26 = 52.00 meters

2. Refer the table 6-8. Divide 52.00 m. by the effective width

1. Find the total length of the flashing ( see figure )

3.00 m. x 4 sides = 12.00 meters

2. Refer to table 6-8, for outside flashing, divide:

RIDGE END CAP

62 pcs. 1.20 x 3.00. standard corrugated sheet

TECHNICAL DATA FOR ESTIMATING ASBESTOS ROOFING

TABLE 6-8 STANDARD CORRUGATED SHEETS

Length - 1.20 x 3.00 m.

FIGURE 6-10 STANDARD CORRUGATES SHEET

B. 4-V CORRUGATED ASBESTOS SHEET

TABLE 6-9 CORRUGATED SHEET TECHNICAL DATA

Standard Length - 2,438 m.

TABLE 6-10 TENCOR CORRUGATED SHEET TECHNICAL DATA

Standard length - 2.44 m.

FIGURE 6-12 TENCOR CORRUGATED SHEET

TABLE 6-11 KANALETAS TECHNICAL DATA

TABLE 6-12 ARDEX TECHNICAL DATA

Standard width 0.52 m 0.105 m.

FIGURE 6-14 ARDEX.

TABLE 6-13 PLACA ROMANA TECHNICAL DATA

Standard length - 0.912 m.

6-5 COLORBOND LIP-LOK

FIGURE 6-16 COLORBOND KLIP LOK

Steel base thickness - 0.60 mm.

Support member Normal Fastening Fastening over insulation

2”x9G(50x 3.75 mm)counter 1

TABLE 6-15 BANAWE METAL TILE TECHNICAL DATA

ITEM LENGTH IN METER

Normal width 0.228 m.

FIGURE 6-17 CROSS SECTION OF BANAWE METAL TILE

You might also like