INSTRUMENT GENERAL SPECIFICATION
Document No.: MMR-SP-60-001-A4
5 of 37
Rev. 3 Date: 25-07-2022
1. PURPOSE
The purpose of this document is to define the minimum technical requirements for the design and
engineering of field instrumentation to be installed on project of “Jasa Konsultasi Penyusunan
Front End Engineering Design (FEED) Pengembangan Terminal BBM Maumere, Nusa Tenggara,
Indonesia.
2. REFERENCE
The latest editions of all applicable codes, specifications and references shall define the minimum
requirements applicable to the subject work and no statement contained in this Specification shall
be construed as limiting the work to such minimum requirements. Codes and standards are listed
in the parts of the Design Basis Manual to which they apply.
AGA (American Gas Association)
AGA 3 Orifice metering of natural gas and other related Hydrocarbon Fluids
API (American Petroleum Institute)
API 6D Pipeline Valves, End Closures, Connectors and Swivels
API 6F Specification for Fire Test for Valves
API RP 505 Recommended Practice for Classification for Locations for Electrical
Installations at Petroleum Facilities Classified as Class I, Division 1 & 2.
API RP 520 Recommended Practice for the Design and Installation of Pressure
Relieving Systems in Refineries, Part. 1 & 2
API RP 521 Guide for Pressure Relieving and Depressurizing Devices
API RP 526 Flanges Steel Safety Relief Valves
API RP 527 Seat Tightness of Pressure Relief Valves
API RP 550 Manual on Installation of Refinery Instruments and Control Systems
API RP 551 Process Measurement Instrumentation
API 2000 Venting Atmospheric and Low-Pressure Storage Tank
API RP 552 Transmission System
API RP 554 Process Instrumentation and Control
API MPMS 3.1A Manual of Petroleum Measurement Standards
API MPMS Chapter 5.2 Displacement Meters
API MPMS 5.3 Measurement of Liquid Hydrocarbon by Turbine Meters
API RP 598 Valve Inspection and Testing
INSTRUMENT GENERAL SPECIFICATION
Document No.: MMR-SP-60-001-A4
6 of 37
Rev. 3 Date: 25-07-2022
ASME (American Society of Mechanical Engineers)
ASME B16.11 Forged Steel Fittings, Socket Welding and Threaded
ASME B16.20 Metallic Gaskets for Pipe Flanges – Ring Joint, Spiral Wound and
Jacketed
ASME B16.21 Non-metallic Gaskets for Pipe Flanges
ASME B16.36 Steel Orifice Flanges – Class 300,600, 900, 1500 & 2500
ASME PTC 19.3 Power Test Code for Thermowells
ASME Sect. VIII ASME Boiler & Pressure Vessel Code, Section VIII Pressure Vessels,
Division 1 “Rules for Construction of Pressure Vessels”
ISA (Instrument Society of America)
ISA S5.1 Instrumentation Symbols and Identification
ISA S5.2 Binary Logic Diagrams for Process Operation
ISA S5.3 Symbols for Distributed Control/ Shared Display Instrumentation, Logic
and Computer Symbols
ISA S5.4 Instrument Loop Diagrams
ISA S7.0.1 Quality Standard For Instrument Air
ISA S75.01 Control Valve Sizing Equations
ISA S 20-1981 Specification Forms for Process Measurement and Control Instruments,
Primary Elements and Control Valve
ISA S 5.5 Graphic symbol for process display
ISA S 75.19 Hydrostatic testing of control valves
ISA 84.01 Application of Safety Instrumented System for the Process Industries
IEC (International Electrotechnical Commission)
IEC 61000 – part 5 Electromagnetic Compatibility (EMC)
IEC 60079 – part 0 to 14 Electrical apparatus for explosive air atmospheres
IEC 60364 Electrical installations of buildings
IEC 60529 Degrees of protection provided by enclosures (IP code)
IEC 61508 – part 1 to 6 Function Safety of Safety Related System
IEC 62591 Wireless HART® System Engineering Guide.
IEC 581 – part 1 Thermocouple Reference Table Accessories.
INSTRUMENT GENERAL SPECIFICATION
Document No.: MMR-SP-60-001-A4
7 of 37
Rev. 3 Date: 25-07-2022
ASTM (American Society for Testing and Materials)
ASTM D 1085/API 2545 Standard Method of Gauging Petroleum and
Petroleum Products.
ASTM D 1086 Standard Method of Measuring Temperature
Petroleum and Petroleum Products.
A106 Gr. B Specification for Seamless Carbon Steel Pipe.
A411 Specification for Seamless Stainless Mechanical Tubing.
NEMA (National Electrical Manufactures Association)
NEMA 250-2014 Enclosure for Electrical Equipment (1000 Volts Maximum)
NFPA (National Fire Protection Association)
NFPA 70 National Electrical Code
ISO (International Standard Organization)
ISO 5167 Measurement of fluid flow by means of pressure differential devices –
Part. 1: Orifice Plates, Nozzles and Venturi tubes inserted in circular
cross-section conduits running full
ISO/TR 5168 Measurement of fluid flow – Evaluation of uncertainties
Standar Industri Indonesia (SII)
Pengaturan dan ketentuan PT. PERTAMINA (Persero) Direktorat Pemasaran serta Ditjen MIGAS
2.1. ORDER OF PRECEDENCE
In the event that there are conflicts with items or information contained within the specification, the
following order of precedence shall be used when interpreting the information of COMPANY-
provided documentation and references:
1. Engineering/Purchase Order
2. Data Sheets
3. Specification/Drawings
4. Other Related Document
5. International Standards & Codes
6. Government Regulation
INSTRUMENT GENERAL SPECIFICATION
Document No.: MMR-SP-60-001-A4
8 of 37
Rev. 3 Date: 25-07-2022
Appropriate codes and standards of the associations and approval bodies listed in the
specifications shall apply in cases not covered by the specifications.
Any deviations/exception taken by the VENDOR shall be clearly identified and listed out which
shall be submitted in his proposals; except as so stated and accepted, it shall be considered and
required that the equipment and services offered shall be in full compliance with the specification.
3. DEFINITION AND TERMS
3.1. DEFINITIONS
The following Definitions as used in this specification assume the meanings given below:
COMPANY PT. PERTAMINA PATRA NIAGA.
CONTRACTOR The Company or Consortium which is awarded the main PT.
PERTAMINA PATRA NIAGA contract for the project.
PURCHASER The party which places the order or signs the contract (This
may be CONTRACTOR at all times or COMPANY followed by
CONTRACTOR at time of novation).
VENDOR The COMPANY on which the order or contract for supply of the
goods or services is placed.
3.2. TERMS
Throughout this document, the words ‘will’, ‘may’, ‘should’, ‘shall’ & ‘must’, when used in the
context of actions by PT. PERTAMINA PATRA NIAGA or others, have specific meanings.
For purposes of this Specification, the following terms apply:
Will: Used normally in connection with an action by PERTAMINA PATRA NIAGA rather than by
a contractor or supplier.
May: Used if alternatives are equally acceptable.
Should: Used if a provision is preferred.
Shall: Used if a provision is mandatory by PERTAMINA PATRA NIAGA.
Must: Used only if a provision is a statutory requirement.
INSTRUMENT GENERAL SPECIFICATION
Document No.: MMR-SP-60-001-A4
9 of 37
Rev. 3 Date: 25-07-2022
4. ABBREVIATION
AC Alternating Current
AGA American Gas Association
ANSI American National Standards Institute
API American Petroleum Institute
ASME American Society of Mechanical Engineers
AWG American Wire Gauge
CSA Canadian Standards Association
dB Decibel
DC Direct Current
ESD Emergency Shutdown
FAT Factory Acceptance Test
FM Factory Mutual
FO Fiber Optic
F&G Fire and Gas
IEC International Electro technical Commission
ISA International Society of Automation
IS Intrinsically Safe
I/O Input / Output
I/P Current / Pneumatic
NEMA National Electrical Manufacturers Association
NFPA National Fire Protection Association
NPT National Pipe Taper
PC Personal Computer
PCS Process Control System
PLC Programmable Logic Controller
PSV Pressure Safety Valve
SAT Site Acceptance Test
SDV Shutdown Valve
SIS Safety Instrumented System
UPS Uninterruptible Power Supply
INSTRUMENT GENERAL SPECIFICATION
Document No.: MMR-SP-60-001-A4
10 of 37
Rev. 3 Date: 25-07-2022
5. GENERAL REQUIREMENT
5.1. UNIT AND MEASUREMENT
All units of measurement used in drawing and text shall conform to the international system of unit
(SI) as presented in the following Table.
Parameter Unit Symbol
Distance Kilometers km
Length meter m or mm
Elevation meter M or mm
Area square meter m2
Volume, Liquids Meter cubic/liter m3 or liter or kilo liter
Volume, Gases Meter cubic m3 (actual or std)
Liquid Volumetric Flow Meter cubic/hour, kiloliter/hour m3/h or kl/h
Production, Liquid Barrel per day BPD
Weight (Mass) kilogram kg
Composition mole percent mol %
Liquid Volume Fraction volume percent vol %
Mass Concentration parts per million (molar) ppm
Mass Flow kilogram per hour kg/h
Velocity meter per second m/s
Density kilogram/meter cubic kg/m3
Viscosity centipoise cP
Pressure (Absolute) Kilogram/square centimetre Kg/cm2 a
Pressure (Gauge) Kilogram/square centimetre Kg/cm2 g
Pressure (Vacuum) Kilogram/square centimetre Kg/cm2
Temperature degree Celcius °C
Power Kilowatt kW or kVA
Heat Kilo calori K Cal
Pipe Diameter Inch (nominal) In
Pipe Wall Thickness milimeter mm
Sound Intensity Decibel dB(A)
Milimeter mm
Level Meter m
Percentage %
All instruments measurement and indication shall cover the full process operating range unless
approved otherwise by COMPANY.
