EKATERINA LUKASHEVA

MODERN KUSUDAMA
ORIGAMI

1
 Copyright © 2015 by Ekaterina Pavlović (Lukasheva)

All rights reserved. No part of this publication may be reproduced, distributed, or transmitted in any form or by
any means, including photocopying, recording, or other electronic or mechanical methods, without the prior
written permission of the publisher, except in the case of brief quotations embodied in critical reviews and certain
other noncommercial uses permitted by copyright law. The designs in the book are intended for personal use
only, no commercial use without author’s written permission. For permission requests, write to [email protected].

Publisher’s Cataloging-in-Publication data

Lukasheva, Ekaterina.
A title of a book : Modern Kusudama Origami / Ekaterina Lukasheva
ISBN-13: 978-1516933686
ISBN-10: 1516933680

The origami models in this book were created by Ekaterina Pavlovic(Lukasheva) in following years:
2011: Apricot, Compass, Compass Star, Malachite, Phoenix, Phoenix Feather;
2012: Centaurea Cyanus, Centaurea Flower, Cream, Floweret, Ice, Jaciara, Rio;
2013: Bouquet, Celestina, Ice Cream, Jade Star, Lathyrus, Ornamentarium, Serenade, Snow Queen, Windflower.

Thanks to all the people who helped me making, test folding,

proofreading and illustrating this book. Namely

Elena Belogorodtseva
Ekaterina Kim
Boris Pavlović
Alena Rodakova
Natalia Romanenko
Tanya Turova
Jean Wallace
and all other people who inspired, encouraged and asked me to write a new book.

Photo credits

Ekaterina Kim: portrait on the cover.

Alena Rodakova: picture on page 52 (bottom).
Natalia Romanenko: picture on page 45.
Tanya Turova: pictures on page 30, page 34, page 36, page 57, page 61, page 63, page
68, page 70 and the cover.

2
CONTENTS
6 origami symbols
8 cutting rectangles
10 what is modular origami
10 about the author
11 modular assembly page 20
12 octahedron (12A)
13 cube (12B)
14 icosahedron (30A)
15 dodecahedron (30B)
16 assembly hint
16 tips and tricks
17 book symbols
18 models

page 18

page 24 page 42 page 43

page 28 page 32 page 53

3
 page 57 page 57 page 48

page 34 page 54 page 30

page 26 page 36 page 40

page 61 page 59 page 63

4
page 70 page 64 page 66

page 68 page 38 page 56

page 45 page 80 page 78

page 75 page 76 page 72

5
 Origami symbols

valley fold mountain fold

valley fold and unfold mountain fold and unfold

equal lengths equal angles unfold

pleat fold unfold/pull paper

6
enlarged view ahead curl

sink fold inside reverse fold

back (hidden) layer repeat on the other side

90˚ 90˚
90˚ 90˚

rotate 90˚ (or any other angle if specified) turn paper over

90˚

semi-fold (precrease) put inside

7
 How to cut a...
1:2 rectangle (half square)

1 2

2:3 rectangle

1 2 3

4 2/3 1/3 5 6
At step 4, the gray part is equal to 2/3 of the square’s length, and the white part equal to 1/3. If you want a
large 2:3 rectangle, cut the white part away at this step and use the the remaining gray area. If you wish to have
smaller 2:3 rectangles, continue to steps 5-6.

8
2:√3 rectangle

1 2 3

4 5 6

At 4th step you get the needed 2:√3 rectangle. If you wish to have smaller rectangles, continue to steps 5-6.

9
 Modular origami
Origami is the art of paper folding. connection without using any adhesive.
Traditional origami uses a single, uncut sheet This feature of modular origami brings
of paper, whereas modular origami uses it closer to construction sets: you are just
multiple sheets joined together to create making the pieces of the construction set
a singular form. This method offers great yourself prior to the assembly process.
flexibility in shapes you can achieve while There are several names for modular
keeping the single unit relatively simple. So origami throughout the world. In the west
if you dislike 100+ step origami diagrams it’s referred to as modular origami, but in
still wanting the resulting piece to look Eastern Europe and South America, the
intricate, modular origami is for you. Japanese word “kusudama” is is commonly
The figures created through modular origami used for ball-like modular origami figures. In
are usually highly symmetric, because they Japan, the word “kusudama” originally meant
are made from multiple equivalent units, “medicine ball”, possibly referring to a ball
or modules. The origami modules usually made from flowers and used for incense.
have special locks to allow unit-to-unit

About the author

My name is Ekaterina Lukasheva, but my world. I have the website www.kusudama.me
friends call me Kate. I became acquainted with numerous kusudama pictures, as well
with modular origami as a teenager; it as a few free diagrams and videos.
quickly became my passion and has been I was born in 1986 in Moscow, Russia.
ever since. As I grew up, I continually Since early childhood I adored architecture
developed my modular origami skills, and and design art books and catalogs, as
at some point, I started creating my own well as “entertaining math” books. I tried
designs. It is very interesting, since I compose several hobbies throughout my life like
the puzzles that I can then assemble into construction sets, drawing, oil-painting,
beautiful spheres. When I create a new photography, modelling and... origami. The
origami model, I try to either make it look latter possesses me at the moment. For me
different from the existing models or make it’s the best culmination of mathematics, art
its modular locks different. In this book, I and design. I gain inspiration from various
gathered models with locks that may seem 3-dimensional objects like flowers, cacti,
unusual or challenging to you, but once you architecture objects and stellated polyhedrons.
get the hang of them, you’re sure to like them! While I graduated as a specialist in
My first book Kusudama Origami was applied math and programming and
published in 2014 by Dover publishing. completed my PhD on differential equations,
Besides that I usually publish my diagrams I don’t feel any of these things are needed
in various origami journals throughout the to make and enjoy beautiful origami. ;)

10
Modular assembly
The units presented in this book can be assembled in various ways. The assembly methods
for modular origami spheres are based on the structure of Platonic1 and Archimedean2 solids.
Each unit corresponds to an edge of the solid. The detailed assembly of these solids is outlined
below.

There are two types of units in this book: ‘edge’ units and ‘solid’ units. The former act and
look like real edges of the solids when you assemble the modules. But indeed the ‘solid’ units
act in the same way: the only difference is that the final shape becomes solid, and the holes
between the units turn to the pyramids.

edge units solid units

It means that the same assembly methods can be used for the both ‘types’ of the units. The
following image illustrates the correspondence between units and the underlying solids.

vertex vertex edge

edge

vertices
vertex vertex edge
edge

vertices

The methods below will illustrate the assembly methods for the edge units. But the same
assembly schemas apply to the solid units as well. The assembly schemas are given
symbolically, each arrow represents the unit’s particular connection method.

1 Platonic solid is a regular convex polyhedron composed of identical regular polygons meeting
in identical vertices.
2 Archimedean solid is a highly symmetric, semi-regular convex polyhedron composed of two or
more types of regular polygons meeting in identical vertices. They are distinct from the Platonic
solids, which are composed of only one type of polygon meeting in identical vertices.

11
 Octahedron 12A method

A regular octahedron is a Platonic solid composed of 8 equilateral triangles, 4 of which meet at each vertex. Since
an octahedron is formed with 12 edges, you will need 12 units to complete a modular octahedron figure.

connect 4 units so that continue adding the units so that every 3 units form a
they meet at a single point triangular hole (triangular pyramid in case of solid units)

complete octahedron

add 4 more units so that 4

units meet at a single point each time

connect the sides marked with the stars

in the illustration to one point behind,
completing the octahedron

solid version of octahedron: dotted

lines show the underlying octahedron

12
Cube 12B method

A regular cube is a Platonic solid composed of 6 square faces,

with 3 edges meeting at each vertex. Since a cube is formed with
12 edges, you will need 12 units to complete a modular cube
figure.

connect 3 units so that they add units to the loose sides of the edges so
meet at a single point that 3 units meet at a single point each time

connect loose units as shown add the remaining units so that 3 units meet at
a single vertex, connect the sides of the units
marked with triangles to a single point behind

complete cube solid version of the complete cube: dotted line

shows the underlying cube

13
 Icosahedron 30A method

An icosahedron is a polyhedron composed of 20 triangular faces, with 5 of those meeting at each vertex.
Since an icosahedron is formed with 30 edges, you will need 30 units to complete a modular icosahedron figure.

connect 5 units so that add 5 more units to connect 2 additional units to every
they meet at a single point form 5 triangles unfinished vertex, so that 5 units meet at
a single vertex each time

connect the loose sides of the units add units to the

so that they form 5 triangles non-finished vertices so that
5 units meet at a single point
the units marked with the stars in the
picture should meet at a single point

complete icosahedron (left)

and the solid version of
icosahedron (right)

the size of the holes as well as the

sharpness of the spikes may vary
from unit to unit

14
 Dodecahedron 30B method

A dodecahedron is a Platonic solid composed of 12 pentagonal faces, with 3 of those meeting at each vertex. Since a
dodecahedron is formed with 30 edges, you will need 30 units to complete a modular dodecahedron figure. The assembly
scheme described below may not be the most comfortable; while it illustrates the algorithm, the actual sequence of the 5
assembly may be slightly different. 5

connect 5 units so that they connect 5 more units so that add 2 units to every loose side
form a ring every three units meet at a of the unit so that 3 units meet
single vertex as shown at every point
1
2
1
2
1 5

!
2 4
!
5
3

3
5
3
5

4
add 5 more units so
that every 3 units meet at a single
point, then make a new ring of units
the same way you did in the first step
4
connect the loose edges so
that you get 5 pentagonal rings connect this new ring to the figure so that 4

around the central one the numbers in the gray pentagons match up

this picture is to illustrate the structure only, as it is

more comfortable to add the last 5 units
one by one

complete dodecahedron (left)

and the solid version of
dodecahedron (right)

the size of the holes as well as the

sharpness of the spikes may vary
from unit to unit

15
 Assembly hint
Almost all of the models in this book (except polyhedron first. Thus, when you assemble
Apricot, Compass, Malachite and Windflower an icosahedron, finish the vertices where
stars) share a similar connection system which five edges are connected. Since a “star” of
can look unstable at first glance. However, if five units is enclosed it becomes stable (steps
you join the pieces as shown below, they will 1-5 in the picture). Instead of closing the
connect more stable, and assembly process adjacent triangles, you should then assemble
will be more comfortable. The diagram below the next “star” (steps 6-10). Continue to
illustrates the modified assembly sequence assemble the model by finishing the vertices,
How to assemble units:
for the icosahedron (30A method), but the proceeding in this fashion until the model is
sametheidea may bebecomes
connection appliedstable
to any sphere
when finished.
it’s connected As you
to the closed go, keep in mind that the
”star”.
you Close
assemble. The concept behind this holes between the
the circle from first 5 units and then arrange the second star neat the unitsfirst.
should be triangular.
method is to try and finish the vertices of the

1
7
6
2
5
8

3 10
4
9

Tips and tricks

Continue adding units so that each five meet at one point
and the windows between the units are triangles. You will need 30 units.
• IfTry
youtoassemble
chooseother
papers of theforms
modular same(below)
type you should
• Ifassemble
you are complete
not sure how to perform a
vertices
toand
makeweight for a single model. If you
them stable. particular step, refer to the next step in
mix papers with different properties in the diagram, as the illustration should
a single model it may not only look give you a hint of the resulting shape.
inconsistent but may also lack symmetry.
• If you would like to use sticky notes for
• Try folding a test unit from lager piece of folding , you can apply some corn-
paper before starting the entire modular. starch directly on the adhesive, making
It may give you a hint as to what paper it less sticky and more ideal for folding.
size would be most comfortable for you,
as well as how the color or pattern of • Be as accurate as possible when making
the paper will appear when folded into every single unit. The more precise
a particular module. you are, the better the final model will
look. Some modular locks only function
12 units when your 30folding
units is very precise.

16
For precise and sharper creases A pincer or tweezers can be
use a folder or a wooden stick. very handy during the assembly
You may find a special origami process or for curling the petals.
folder or use some clay model- Use it when you need to tuck the
ling tools you can find in any art small flaps into pockets.
supply store.

Paper and craft knives

can be used for cutting
paper.

A letter opener can be

very useful for cutting paper
when you travel; you can
take it even on board!

Clips can be helpful to

PVA glue temporarily fasten the units for
stability during the assembly.

The models in the book do not generally require glue for assembly, but if you are a novice to modular origami
you may need some. If you want your kusudama have a better chance of staying together when handled by
guests, children or gently batted by animals, add a bit or glue during assembly or to a complete model. Stick
glue is better during assembly, while PVA glue (white liquid glue) can be used to fasten more permanently the
complete model. Add a drop of PVA glue to the point where units meet to fasten the point. This glue becomes
nearly invisible when dry, but be sure to test it on a scrap of your selected paper before adding to the kusudama.

Near the model name for each diagram in this book, you will find some symbols and other indicators with
suggestions to help guide you in your paper selection, as well as the difficulty level and assembly possibilities for
a particular model.

suggests the use of

origami-specific difficulty level out of 5
gradient paper

suggests the use of paper

with different colors on recommended assembly
each side method and number of
30A, 12A
units (see pages 12-15)
7x7 cm square

MODEL NAME
recommended paper size
(novices may want to use larger
paper, whereas experienced
folders could go even smaller)

17
 5-8 units

5x5 cm square

WINDFLOWER
STARS

This star is a perfect starter; it is easy to make and spectacular when

finished. You may use these stars for many decorative purposes: glue
them to the gift card or make a little brooch. You can make this star
out of 5 or more units. I recommend making it from 5 to 10 units.
The more units you add the fluffier your star will get. Use pincers
to curl the loose flaps at the end of the assembly process.

18
1 2 3

4 5 6 semi-fold

complete unit in progress

insert the two flaps into the
two pockets simultaneously

continue adding units

you can make a star with 5 or more units
when you stop adding units, connect the
free sides to create a star

19
 5-8 units

5x5 cm square

FLOWERET

1 2 3

20
 This is sample pdf.

4
You can learn more5 about the books here:
bring the top right point 6 bring the top right point
down to meet the central down to meet the central
http://www.books.kusudama.me/
line as shown line as shown

You can buy the book here:

http://www.amazon.com/dp/0997311940

Contact: [email protected]

7 fold simultaneously 8 fold central line 9 fold using existing 10 this step is optional:
let the upper part without folding lines, so the figure you may curl the
stay unfolded the upper flap becomes flat again upper flap

flap

place
for the
flap to connect units
insert the flap into 2 connected units:
the pocket (the place add 3-5 more and
for the flap) complete your star

11 unfold a bit the complete unit

21