See discussions, stats, and author profiles for this publication at: https://www.researchgate.

net/publication/351392014

Tensile Testing Concepts & Definitions

Cover Page · May 2021

CITATION READS
1 4,451

1 author:

Deniz Yalcin
ADMET
13 PUBLICATIONS   5 CITATIONS   

SEE PROFILE

Some of the authors of this publication are also working on these related projects:

ADMET Materials Testing View project

All content following this page was uploaded by Deniz Yalcin on 07 May 2021.

The user has requested enhancement of the downloaded file.

Tensile Testing Concepts & Definitions
Tensile tests are used to determine how materials behave under tension load. In a
simple tensile test, a sample is typically pulled to its breaking point to determine the
ultimate tensile strength of the material. The amount of force (F) applied to the sample and
the elongation (∆L) of the sample are measured throughout the test.

Material properties are often expressed in terms of stress (force per unit area, σ)
and strain (percent change in length, ε). To obtain stress, the force measurements are
divided by the sample’s cross sectional area (σ = F/A).

Strain measurements are obtained by dividing the change in length by the initial length of
the sample (ε = ∆L/L). These values are then presented on an XY plot called a stress-strain
curve. Testing and measuring procedures vary based on the material being tested and its
intended application.

Core Concepts of Tensile Testing

The following section will address key ideas related to tensile testing. All software output
screens are from an ADMET MTESTQuattro-equipped tensile tester.

Stress and Strain

These are basic dimensions of material science. Stress is the amount of force per unit cross
sectional area. Strain is the ratio of the change in length to the original length, sometimes
expressed as a percent. Tensile tests use plots of stress vs strain to display results.
Elastic Deformation

Elastic deformation is the region on the stress-strain curve where deformation can be
reversed by removing stress. It is also the region where stress is mostly proportional to
strain. It can be identified on a stress-strain curve as the initial linear section of the graph.
Young’s Modulus

Young’s modulus, also known as the elastic modulus, is the constant which relates the
proportion of stress (σ) to strain (ε) under elastic deformation. On a stress-strain curve, it is
the initial slope of the linear region of the graph. This relation is represented by the
equation σ =E•ε. This relation is referred to as Hooke’s Law, which was developed to
represent the behavior of springs.
Proportional Limit

The first instance on the stress-strain curve where the plot begins to deviate from the line
marking Young’s modulus. This deviation is often gradual and is dependent on the
material.

Plastic Deformation

Strain beyond the material’s yield point induces strain hardening, which permanently
deforms the material and causes changes to its mechanical properties.

Yield Point

The yield point marks the end of the elastic deformation region and the beginning of the
plastic deformation region. It is characterized by a sharp bend in the stress-strain curve at
the end of the elastic region. Materials that exhibit no definitive end to the elastic region do
not have a yield point. In those cases, yield is approximated by the offset method.
However, it can only be determined experimentally by loading and unloading, gradually
increasing stresses to find where plastic deformation begins.
Offset Method

For materials that do not have a clear end to the initial linear region, the offset method is
used to approximate yield. The offset method uses the stress-strain curve of the material
and overlays a line with a slope equal to the initial slope of the stress-strain curve. The line
is offset along the strain axis, usually by 0.2% (the line crosses the strain axis at ε = 0.002).
The offset yield point is determined as the point of intersection between this line and the
stress-strain curve.
Ultimate Tensile Strength (UTS)

The ultimate tensile strength is the maximum amount of stress a material can withstand
before failure. This is the maximum value on the stress-strain curve.
Tangent Modulus

Tangent modulus is used to approximate the slope at a given point on the stress-strain
curve. The graph shows an exaggerated example. Refer to ASTM standards when selecting
points for a tangent modulus.

Chord Modulus

Chord modulus is used to approximate the slope between two specific points on the stress-
strain curve. The graph shows an exaggerated example. Refer to ASTM standards when
selecting points for a chord modulus.
Secant Modulus

Some materials do not have a linear region to their stress-strain curve, therefore Young’s
modulus cannot be determined directly from the curve. The secant modulus is used in its
place as an approximation. Secant modulus takes the slope of a line which intersects the
origin of the stress strain curve, and a point on the curve. One example is described in
ASTM D5323, which calls for the point to be placed at 2% strain (ε = 0.02), but the position
of this point can vary by material and procedure. This method is most useful for material
comparison. This graph shows an exaggerated example. Refer to ASTM standards when
selecting points for a secant modulus.
How to Perform a Tensile Test

Generally speaking, to perform tension testing, you will need

the following equipment:

• Universal test machine frame

• Load cell
• Controller and/or indicator
• Proper grips and fixturing to hold your sample

The universal test machine frame provides the structure and

rigidity needed to pull the sample apart at the desired
rate. Frames are available in both electromechanical and servo-
hydraulic configurations with a wide range of capacities. It is
important to select a frame which can withstand the amount of
force needed to test the sample.

Load cells measure the amount of force being applied to the sample.

Like frames, these come in a variety of capacities.

Choosing a load cell with a capacity below the required
breaking strength will result in the load cell breaking
before the sample does. Conversely, a load cell with too
high a capacity will lead to test results that may lack the
precision desired as resolution of load cells typically goes
down to 1%. For example, a 1,000 lb load cell would be
far too high a capacity for a sample that breaks under 1
lb of force.

Depending on your system setup, you may need a controller or an indicator. Controllers, as
the name implies, control how the test frame behaves during testing, including test speed
and displacement. In some situations, an indicator may be all that is required. Indicators
capture and display the test data but do not control the machine.
 There are many types of grips and fixtures available for tension
testing. Different materials require different fixturing to properly
hold them. For instance, a sample made of metal requires different
grips than a stretchy piece of rubber due to how the materials
behave as tensile forces are applied. Selecting the correct grips for
your application is crucial in achieving accurate results.

View publication stats