Scribd
Upload
297 views5 pages

Tronxy X3 Operating Instruction

The document provides instructions for operating the Tronxy 3D printer model X3. It describes how to insert the micro SD card, use the LCD screen and control buttons, load and unload PLA filament, level the print bed, and perform offline printing from an SD card. Key steps include preheating the extruder to 190 degrees, straightening the filament ends, feeding filament through the extruder hole and nozzle, adjusting the distance between nozzle and bed using thumb nuts, and selecting print files on the SD card to start a print.

Uploaded by

adrian
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
297 views5 pages

Tronxy X3 Operating Instruction

The document provides instructions for operating the Tronxy 3D printer model X3. It describes how to insert the micro SD card, use the LCD screen and control buttons, load and unload PLA filament, level the print bed, and perform offline printing from an SD card. Key steps include preheating the extruder to 190 degrees, straightening the filament ends, feeding filament through the extruder hole and nozzle, adjusting the distance between nozzle and bed using thumb nuts, and selecting print files on the SD card to start a print.

Uploaded by

adrian
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

Tronxy 3D Printer

X3
Operating Instruction
Preparatory Work
Turn on the power after micro SD card insert, then you can control
the machine using key-press and the LCD display, as picture below:

Micro SD card slot is at the back of the Plug in adaptor after Micro
electronic box, near the USB Interfaces. SD card is inserted.

LCD screen and Key-press function instruction


Key-press

LCD screen

Key-press Name Key-press Function Remark

Left Back To Previous Menu

Right Go to next menu/Enter key

Up Menu Up / Add

Down Menu Down / Minus

Middle Start menu


Loading & Unloading PLA
Loading PLA :

1, Press menu button, Straighten


select ‘Preheat PLA’, one end of
then Right key to the
confirm. filament
2, Take the filament and
then straighten one end
after Temp. up to 190
degrees.
3, Press the extrution
clip , feed the filament
into the hole. Feed the
4, Run the filament filament
along the teflon tube into the
until the filament comes hole
out from the nozzle.

Unloading PLA :

1, As in the above, Press


menu button, select
‘Preheat PLA’, then Right Until the
key to confirm. filament
2, Press the extrution into the
clip , pull out the nozzle
filament from the nozzle through
after Temp. up to 190 here
degrees
Level Instruction
In order to better printing , we also need to level the print bed or the
filament may not adhere to the bed that result in poor printing quality
and can not print.
1 Please clean the nozzle to make sure there are no remained
material before leveling.
2 Turn on the power, press the menu button , select‘Quick setting’ ,
then select ‘Home all’ , the printer start homing. (Figure 1)
3 After Home all , press menu button to select ‘Disable stepper’,
then you can move the axis manually. (Figure 2)
4 Move the extruder and platform manually, observe the distance
between nozzle and four corners of the platform and to assure the
same distance of them . If higher or lower , please adjust the
thumb nuts below the bed frame.
5 Note: You can put one A4 paper between the nozzle and platform,
pulling the paper backwards and forwards, if it happens to have a
little bit of resistance, that is well spaced.

Figure 1 Figure 2

Adjust the thumb nut

Move extruder Move platform

Observe distance
Observe distance
Off-line Printing
Operate the printer with the key-press and LCD screen after print bed is
leveled, as shown below:

You will see the ‘monitoring


interface’ first after power on

Press menu button go into


‘menu screen’.

Press Down key after into


menu, then you will see ‘SD
card’
Press Right key and select
‘SD card’,and then press
Right key select ‘Print file’.

Select a Gcode file which


you want to print, then press
Right key to start print.

You’ll see the monitor


interface when printing, it
shows Nozzle temperature,
and the printing completion
rate.

If want to ‘Pause Print’ or


‘Stop Print’, Press Manu
key ,select ‘SD card’,then
the screen will appear the
interface as left picture .
Select Pause or Stop , press
Right key to confirm.

You might also like