K-TRON Product Specification K2-ML-D5-S60

Single Screw Loss-in-Weight Feeder

A Ext. communication to Host System Each K-TRON Weigh feeder consists
C D A Feeder of the components A, B, C and D.
B Weighing System
Component A is specified here.
C Control Module
B D Operator Interface

Application
Gravimetric feeding of free flowing powders, granules and other bulk materials.

Design
Single screw feeder with interchangeable feeding tool mounted on a D5 weigh bridge.
The weigh bridge is stainless steel and the scale housing is completely enclosed.
All parts in contact with the material being fed are stainless steel. Feeding equipment is
easy to disassemble. The horizontal agitator gently moves the bulk material to the large
throat and then into the screws. Feeder screws are easily interchangeable.
This equipment conforms to CE standards regarding EMC and safety.

Controller: (see separate data sheets)

The SmartConnex® control system allows individual or multi-component control. Each
feeder has its own control module. Connection between feeders, operator interface and
smart I/O is via an industrial network. A variety of protocols is available for connection
to the plant’s host system.
Hazardous Location Options: (see sheet I-000002)
NEC Class II, Div. 2, Groups F & G / Class II, Div. 1, Groups F & G
Class I, Div. 2, Groups C & D / Class I, Div. 1, Groups C & D
ATEX 3D/3D, 3D/2D (outside/inside)

Feed Screws and Feed Rates

Actual feeder screws are determined based on the material being fed.
Attention: The following rates are theoretical values for free flowing materials being
fed volumetrically. Actual feed rates depend on individual material characteristics.
The feed range for loss-in-weight feeders is somewhat smaller. For feed rates at the
upper or lower limits of the theoretical range, check with a K-Tron Test Lab.

Auger screw Spiral screw

Reduction/
Pitch Max Screw
Speed (RPM)
Coarse Maximum Particle
3 (0.10) 4 (0.15) 6 (.25) 8 (0.30) 9 (0 .35) 4 (0.15)      6 (.25)    9 (0 .35) Size mm (in)
15mm 25mm 40mm 50mm 60mm 25mm 40mm 60mm
.425 - 42.5
3.40 - 340 11.3 - 1130 24.1 - 2410 45.0 - 4500 4.25 - 425 8.50 - 850 42.5 - 4250 dm3/hr High
.150 - 15.0 .300 - 30.0 1.50 - 150 3.6:1 / 555
.015 - 1.50 .120 -12.0 .400 - 40.0 .850 - 85.0 1.60 - 160 ft3/hr
.115 - 11.5
.850 - 85.0 2.80 - 280 5.95 - 595 9.06 - 906 1.15 - 115 2.10 - 210 8.78 - 878 dm3/hr Low
.004 - .400
.030 - 3.00 .100 - 10.0 .210 - 21.0 3.20- 32.0 .040 - 4.00 .075 - 7.50 .310 - 31.0 ft3/hr 18:1 / 111
Maximum Particle
Fine 4 (0.15)      6 (.25)     9 (0 .35) 4 (0.15)      6 (.25)    9 (0 .35) Size mm (in)
25mm 40mm 60mm 25mm 40mm 60mm
1.70 - 170 5.65 - 565 28.3 - 2832
2.00 - 200 4.25 - 425 27.5 - 2750 dm3/hr High
.060 - 6.00 .200 - 20.0 1.00 - 100
.070 - 7.00 .150 - 15.0 .970 - 97.0 ft3/hr 3.6:1 / 555
.425 - 42.5 1.40 - 140 7.08 - 708
.500 - 50 1.15 - 115 5.50 - 550 dm3/hr Low
.015 - 1.50 .050 - 5.00 .250 - 25.0
.017 - 1.70 .040 - 4.00 .194 - 19.4 ft3/hr 18:1 / 111

DC-motor with speed controller / Range 1 : 100 / Max. motor speed 2000 RPM
Feed rates when using AC motors: The feed rates may here be roughly estimated through a calculation using the screw speeds.
Europe/Asia: AC motor with frequency inverter / Range 1 : 17 / Max. motor speed 2440 RPM
Americas: AC motor with frequency inverter / Range 1 : 12 / Max. motor speed 1725 RPM

Rev. 3 / 2007-01 S-020303-en

Doc# 0290008303 www.ktron.com Page 1 of 2
 K-TRON Product Specification K2-ML-D5-S60
Single Screw Loss-in-Weight Feeder
Configuration Description Alternatives Remarks Weight kg (lb)

Vertical agitator KS: 230/400 VAC KA: 115/230 VAC 4D (50 L, 80 L) 25 (55)
0.18, 0.25 kW 0.25, 0.33 HP
IP55 or 100/200 VDC 6D (110 L) 36 (79)
0.33 HP
Cover 2D 1 (2.2)
4D 2 (4.4)
6D 3 (6.6)

Extension hopper 2D, 4D or 6D see below

Horiz. agitator 0.7 (1.5)
Trough 5L
2.5 (5.5)

Gearbox 15 (33)

100/200 V DC 3 phase with

Motor 0.45 kW freq. inverter standard: 0.45 kW 12 (26.4)
IP 65 KS: 230/400 VAC
KA: 230/460 VAC
0.55 kW, IP 55
Screws see page 1 2 (4.4)
Outlet Horiz. Vertical Pressure standard: horiz. outlet 1 (2.2)
outlet outlet compensation
Weigh bridge 60 kg 120 kg 200 kg IP65, NEMA 4
(gross capacity) 132 lb 264 lb 440 lb

Materials: Weighing Range:

Product contact parts*: Stainless steel Gross weigh bridge capacity (60, 120, 200 kg) less one third to compen-
DIN 1.4404, 1.4435 (AISI 316L) sate for feeder weight = 45, 90, 150 kg
DIN 1.4409 (ASTM A743 CF3M)
*Horiz. agitator: DIN 1.4034 (AISI 420) standard Temperature-Limits:
DIN 1.4404 (AISI 316L) option Ambient: 0 to 40.5 °C (32 to 105°F)
Seals: PTFE, Neoprene, Silicon Material: standard: -20 to 55 °C (-4 to 130 °F)
Painting: Light grey RAL 7035 option: -20 to 150 °C (-4 to 300 °F)

Dimensions mm (in) Options

D 1 Standard hopper
2 Vertical outlet
3 Special paint / finish
80L
110L 4 Extended screws

80L conical

50L
20L
Asymmetrical Hoppers
H

Volume
H D Weight
dm3 (ft3) mm (in) mm (in) kg (lb)
50 615 400 7
10L
(1.76) (24.2) (15.75) (15.4)
62

optional 80 869 400 11

0
(2

(2.8) (34.2) (15.75) (24.2)

4.

vertical
41

220 (8.75)
)

outlet 110 922 600 17

Ø114.3 (4.5) (3.88) (36.3) (23.62) (37.4)
282 (11.1)

500 (19.69)
400 (15.75)

Symmetrical Hoppers
10 283 220 3
(0.35) (11) (8.66) (6.6)
257 (10)

20 566 220 6
146 (5.75)

(0.71) (22.28) (8.66) (13.2)

80 727 400 11
186 (7.32) 165 (6.5) 400 (15.75) (2.8) (28.62) (15.75) (24.6)
225 (8.86)

Caution: these measurements are for general reference only. Please consult dimensional drawing for exact measurements

K-TRON AMERICA / Pitman, NJ 08071 USA / Tel: (856) 589-0500 / e-mail: [email protected] Rev. 3 S-020303-en
K-TRON (Switzerland) Ltd / CH-5702 Niederlenz / Tel: +41 62 885 71 71 / e-mail: [email protected]
All addresses on sheet: / Alle Adressen auf Blatt: / Toutes les adresses sur fiche: I-000001 Page 2 of 2
Copyright by K-TRON. Covered by patents in USA and other countries. Specifications subject to change without notice.