Scribd Logo
Upload

Welcome to Scribd!

  • 45 views

    RDBALAN Full en Metric A4

    Uploaded by

    David Altarriba
    This document summarizes the specifications and technical details of a direct-acting relief valve model RDBA made by Sun Hydraulics. The valve is a normally closed, pressure-limiting valve used to protect hydraulic components from pressure transients by opening to tank and throttling flow when inlet pressure reaches the valve setting. Key specifications include a maximum capacity of 45 L/min, factory pressure settings established at 15 L/min, and a maximum operating pressure of 350 bar.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    RDBALAN Full en Metric A4

    Uploaded by

    David Altarriba
    45 views2 pages
    This document summarizes the specifications and technical details of a direct-acting relief valve model RDBA made by Sun Hydraulics. The valve is a normally closed, pressure-limiting valve used to protect hydraulic components from pressure transients by opening to tank and throttling flow when inlet pressure reaches the valve setting. Key specifications include a maximum capacity of 45 L/min, factory pressure settings established at 15 L/min, and a maximum operating pressure of 350 bar.

    Original Title

    RDBALAN_full_en_metric_a4

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document summarizes the specifications and technical details of a direct-acting relief valve model RDBA made by Sun Hydraulics. The valve is a normally closed, pressure-limiting valve used to protect hydraulic components from pressure transients by opening to tank and throttling flow when inlet pressure reaches the valve setting. Key specifications include a maximum capacity of 45 L/min, factory pressure settings established at 15 L/min, and a maximum operating pressure of 350 bar.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    45 views2 pages

    RDBALAN Full en Metric A4

    Uploaded by

    David Altarriba
    This document summarizes the specifications and technical details of a direct-acting relief valve model RDBA made by Sun Hydraulics. The valve is a normally closed, pressure-limiting valve used to protect hydraulic components from pressure transients by opening to tank and throttling flow when inlet pressure reaches the valve setting. Key specifications include a maximum capacity of 45 L/min, factory pressure settings established at 15 L/min, and a maximum operating pressure of 350 bar.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 2

    MODEL Direct-acting relief valve

    RDBA CAPACITY: 45 L/min. / CAVITY: T-162A

    snhy.com/RDBA

    CONFIGURATION
    Direct-acting relief cartridges are normally closed, pressure-limiting valves used to protect hydraulic components
    L Control Standard Screw Adjustment
    from pressure transients. When the pressure at the inlet (port 1) reaches the valve setting, the valve starts to open
    A Adjustment 500 - 3000 psi (35 - 210 bar), to tank (port 2), throttling flow to limit the pressure rise. These valves are smooth and quiet, essentially zero leak,
    Range 1000 psi (70 bar) Standard dirt tolerant, immune to silting and are very fast.
    Setting
    N Seal Material Buna-N TECHNICAL DATA NOTE: DATA MAY VARY BY CONFIGURATION. SEE CONFIGURATION SECTION.

    (none) Material/Coating Standard Material/Coating


    Cavity T-162A
    Series 0
    Capacity 45 L/min.
    Factory Pressure Settings Established at 15 L/min.
    Maximum Operating Pressure 350 bar
    Maximum Valve Leakage at Reseat 0,7 cc/min.
    Response Time - Typical 2 ms
    Reseat >85% of setting
    Adjustment - No. of CW Turns from Min. to Max. setting 6
    Valve Hex Size 19,1 mm
    Valve Installation Torque 27 - 33 Nm
    Adjustment Screw Internal Hex Size 4 mm
    Locknut Hex Size 12,7 mm
    Locknut Torque 9 - 10 Nm
    Seal kit - Cartridge Buna: 990162007
    Seal kit - Cartridge EPDM: 990162014
    Seal kit - Cartridge Polyurethane: 990162002
    Seal kit - Cartridge Viton: 990162006
    Model Weight 0.10 kg.

    NOTES U.S. Patent #4,742,846; European Patent Pending

    CONFIGURATION OPTIONS Model Code Example: RDBALAN


    CONTROL (L) ADJUSTMENT RANGE (A) SEAL MATERIAL (N) MATERIAL/COATING
    L Standard Screw Adjustment A 500 - 3000 psi (35 - 210 bar), 1000 psi N Buna-N Standard Material/Coating
    C Tamper Resistant - Factory Set (70 bar) Standard Setting E EPDM /AP Stainless Steel, Passivated
    K Handknob W 800 - 4500 psi (55 - 315 bar), 1000 psi V Viton /LH Mild Steel, Zinc-Nickel
    (70 bar) Standard Setting
    B 300 - 1500 psi (20 - 105 bar), 1000 psi
    (70 bar) Standard Setting
    C 1000 - 6000 psi (70 - 420 bar), 1000 psi
    (70 bar) Standard Setting
    D 200 - 800 psi (14 - 55 bar), 400 psi (28
    bar) Standard Setting
    E 100 - 400 psi (7 - 28 bar), 200 psi (14
    bar) Standard Setting
    S 50 - 200 psi (3,5 - 14 bar), 100 psi (7
    bar) Standard Setting

    c 2019 Sun Hydraulics


    1 of 2
    TECHNICAL FEATURES
    All 2-port relief cartridges (except pilot reliefs) are physically and functionally interchangeable (same flow path, same cavity for a given frame size).
    Will accept maximum pressure at port 2; suitable for use in cross port relief circuits.
    The seals on the adjust screw are exposed to system pressure which means this valve can only be adjusted when the pressure is removed. The setting procedure
    is; check the setting, remove the pressure, adjust the valve, check the new setting.
    Valve is relatively insensitive to varying oil temperatures and oil borne contamination.
    Select a spring range where the desired relief setting is approximately mid-range to high between the minimum and maximum pressure to ensure maximum valve
    repeatability.
    Suitable for use in load holding applications.
    Back pressure on the tank port (port 2) is directly additive to the valve setting at a 1:1 ratio.
    Cartridges configured with EPDM seals are for use in systems with phosphate ester fluids. Exposure to petroleum based fluids, greases and lubricants will damage
    the seals.
    Incorporates the Sun floating style construction to minimize the possibility of internal parts binding due to excessive installation torque and/or cavity/cartridge
    machining variations.

    PERFORMANCE CURVES

    c 2019 Sun Hydraulics


    2 of 2

    You might also like