Product Name: MOBIL DTE OIL LIGHT

Revision Date: 16 May 2017

Page 1 of 13

_____________________________________________________________________________________________________________________

SAFETY DATA SHEET

SECTION 1 IDENTIFICATION OF THE SUBSTANCE / MIXTURE AND OF THE
COMPANY / UNDERTAKING

As of the revision date above, this SDS meets the regulations in the United Kingdom & Ireland.

1.1. PRODUCT IDENTIFIER

Product Name: MOBIL DTE OIL LIGHT
Product Description: Base Oil and Additives
Product Code: 201560501560, 400297, 600148-60

1.2. RELEVANT IDENTIFIED USES OF THE SUBSTANCE OR MIXTURE AND USES ADVISED AGAINST
Intended Use: Lubricant

Uses advised against: This product is not recommended for any industrial, professional or consumer use
other than the Identified Uses above.

1.3. DETAILS OF THE SUPPLIER OF THE SAFETY DATA SHEET

Supplier: EXXONMOBIL MARINE LIMITED
ERMYN HOUSE
MAILPOINT 31, ERMYN WAY
KT22 8UX LEATHERHEAD
United Kingdom

Supplier General Contact: (UK) (+44) (0) 1372 222 000

E-Mail: [email protected]

1.4. EMERGENCY TELEPHONE NUMBER

24 Hour Emergency Telephone: (UK) (+44) (0) 23 8089 1558

SECTION 2 HAZARDS IDENTIFICATION

2.1. CLASSIFICATION OF SUBSTANCE OR MIXTURE

Classification according to Regulation (EC) No 1272/2008

Chronic aquatic toxicant: Category 3.
H412: Harmful to aquatic life with long lasting effects.
Product Name: MOBIL DTE OIL LIGHT
Revision Date: 16 May 2017
Page 2 of 13

_____________________________________________________________________________________________________________________

2.2. LABEL ELEMENTS

Label elements according to Regulation (EC) No 1272/2008

Pictograms: No Pictograms

Signal Word: No Signal Word

Hazard Statements:

H412: Harmful to aquatic life with long lasting effects.

Precautionary Statements:

P273: Avoid release to the environment.

P501: Dispose of contents and container in accordance with local regulations.

2.3. OTHER HAZARDS

Physical / Chemical Hazards:

No significant hazards.

Health Hazards:
High-pressure injection under skin may cause serious damage. Excessive exposure may result in eye, skin, or
respiratory irritation.

Environmental Hazards:
No additional hazards. Material does not meet the criteria for PBT or vPvB in accordance with REACH Annex
XIII.

SECTION 3 COMPOSITION / INFORMATION ON INGREDIENTS

3.1. SUBSTANCES Not Applicable. This material is regulated as a mixture.

3.2. MIXTURES

This material is defined as a mixture.

Reportable hazardous substance(s) complying with the classification criteria and/or with an exposure limit
(OEL)
Name CAS# EC# Registration# Concentration* GHS/CLP
classification
2,6-DI-TERT-BUTYL-P-CRESOL 128-37-0 204-881-4 01-2119565113- 0.1 - < 1% Aquatic Acute 1 H400 (M
46 factor 1),
Aquatic Chronic 1 H410
(M factor 1)
Note - any classification in brackets is a GHS building block that was not adopted by the EU in the CLP regulation (No 1272/2008)
Product Name: MOBIL DTE OIL LIGHT
Revision Date: 16 May 2017
Page 3 of 13

_____________________________________________________________________________________________________________________
and therefore is not applicable in the EU or in non-EU countries which have implemented the CLP regulation and is shown for
informational purposes only.

* All concentrations are percent by weight unless ingredient is a gas. Gas concentrations are in percent by volume.

Note: See SDS Section 16 for full text of hazard statements.

SECTION 4 FIRST AID MEASURES

4.1. DESCRIPTION OF FIRST AID MEASURES

INHALATION
Remove from further exposure. For those providing assistance, avoid exposure to yourself or others. Use
adequate respiratory protection. If respiratory irritation, dizziness, nausea, or unconsciousness occurs, seek
immediate medical assistance. If breathing has stopped, assist ventilation with a mechanical device or use
mouth-to-mouth resuscitation.

SKIN CONTACT
Wash contact areas with soap and water. If product is injected into or under the skin, or into any part of the
body, regardless of the appearance of the wound or its size, the individual should be evaluated immediately by
a physician as a surgical emergency. Even though initial symptoms from high pressure injection may be
minimal or absent, early surgical treatment within the first few hours may significantly reduce the ultimate extent
of injury.

EYE CONTACT
Flush thoroughly with water. If irritation occurs, get medical assistance.

INGESTION
First aid is normally not required. Seek medical attention if discomfort occurs.

4.2. MOST IMPORTANT SYMPTOMS AND EFFECTS, BOTH ACUTE AND DELAYED
Local necrosis as evidenced by delayed onset of pain and tissue damage a few hours after injection.

4.3. INDICATION OF ANY IMMEDIATE MEDICAL ATTENTION AND SPECIAL TREATMENT NEEDED
The need to have special means for providing specific and immediate medical treatment available in the
workplace is not expected.

SECTION 5 FIRE FIGHTING MEASURES

5.1. EXTINGUISHING MEDIA

Suitable Extinguishing Media: Use water fog, foam, dry chemical or carbon dioxide (CO2) to extinguish
flames.

Unsuitable Extinguishing Media: Straight streams of water

5.2. SPECIAL HAZARDS ARISING FROM THE SUBSTANCE OR MIXTURE

Hazardous Combustion Products: Aldehydes, Incomplete combustion products, Oxides of carbon, Smoke,
Product Name: MOBIL DTE OIL LIGHT
Revision Date: 16 May 2017
Page 4 of 13

_____________________________________________________________________________________________________________________
Fume, Sulphur oxides

5.3. ADVICE FOR FIRE FIGHTERS

Fire Fighting Instructions: Evacuate area. Prevent run-off from fire control or dilution from entering streams,
sewers or drinking water supply. Fire-fighters should use standard protective equipment and in enclosed
spaces, self-contained breathing apparatus (SCBA). Use water spray to cool fire exposed surfaces and to
protect personnel.

FLAMMABILITY PROPERTIES
Flash Point [Method]: >200°C (392°F) [ASTM D-92]
Upper/Lower Flammable Limits (Approximate volume % in air): UEL: 7.0 LEL: 0.9 [Estimated]
Autoignition Temperature: No data available

SECTION 6 ACCIDENTAL RELEASE MEASURES

6.1. PERSONAL PRECAUTIONS, PROTECTIVE EQUIPMENT AND EMERGENCY PROCEDURES

NOTIFICATION PROCEDURES
In the event of a spill or accidental release, notify relevant authorities in accordance with all applicable
regulations.

PROTECTIVE MEASURES
Avoid contact with spilled material. See Section 5 for fire fighting information. See the Hazard Identification
Section for Significant Hazards. See Section 4 for First Aid Advice. See Section 8 for advice on the
minimum requirements for personal protective equipment. Additional protective measures may be
necessary, depending on the specific circumstances and/or the expert judgment of the emergency
responders.

For emergency responders: Respiratory protection: respiratory protection will be necessary only in special
cases, e.g., formation of mists. Half-face or full-face respirator with filter(s) for dust/organic vapor or Self
Contained Breathing Apparatus (SCBA) can be used depending on the size of spill and potential level of
exposure. If the exposure cannot be completely characterized or an oxygen deficient atmosphere is
possible or anticipated, SCBA is recommended. Work gloves that are resistant to hydrocarbons are
recommended. Gloves made of polyvinyl acetate (PVA) are not water-resistant and are not suitable for
emergency use. Chemical goggles are recommended if splashes or contact with eyes is possible. Small
spills: normal antistatic work clothes are usually adequate. Large spills: full body suit of chemical resistant,
antistatic material is recommended.

6.2. ENVIRONMENTAL PRECAUTIONS

Large Spills: Dyke far ahead of liquid spill for later recovery and disposal. Prevent entry into waterways,
sewers, basements or confined areas.

6.3. METHODS AND MATERIAL FOR CONTAINMENT AND CLEANING UP

Land Spill: Stop leak if you can do so without risk. Recover by pumping or with suitable absorbent.

Water Spill: Stop leak if you can do so without risk. Confine the spill immediately with booms. Warn other
shipping. Remove from the surface by skimming or with suitable absorbents. Seek the advice of a specialist
before using dispersants.

Water spill and land spill recommendations are based on the most likely spill scenario for this material;
however, geographic conditions, wind, temperature, (and in the case of a water spill) wave and current direction
Product Name: MOBIL DTE OIL LIGHT
Revision Date: 16 May 2017
Page 5 of 13

_____________________________________________________________________________________________________________________
and speed may greatly influence the appropriate action to be taken. For this reason, local experts should be
consulted. Note: Local regulations may prescribe or limit action to be taken.

6.4. REFERENCES TO OTHER SECTIONS

See Sections 8 and 13.

SECTION 7 HANDLING AND STORAGE

7.1. PRECAUTIONS FOR SAFE HANDLING

Prevent small spills and leakage to avoid slip hazard. Material can accumulate static charges which may cause
an electrical spark (ignition source). When the material is handled in bulk, an electrical spark could ignite any
flammable vapors from liquids or residues that may be present (e.g., during switch-loading operations). Use
proper bonding and/or earthing procedures. However, bonding and earthing may not eliminate the hazard from
static accumulation. Consult local applicable standards for guidance. Additional references include American
Petroleum Institute 2003 (Protection Against Ignitions Arising out of Static, Lightning and Stray Currents) or
National Fire Protection Agency 77 (Recommended Practice on Static Electricity) or CENELEC CLC/TR 50404
(Electrostatics - Code of practice for the avoidance of hazards due to static electricity).

Static Accumulator: This material is a static accumulator.

7.2. CONDITIONS FOR SAFE STORAGE, INCLUDING ANY INCOMPATIBILITIES

The type of container used to store the material may affect static accumulation and dissipation. Do not store in
open or unlabelled containers. Keep away from incompatible materials.

7.3. SPECIFIC END USES

Section 1 informs about identified end-uses. No industrial or sector specific guidance available.

SECTION 8 EXPOSURE CONTROLS / PERSONAL PROTECTION

8.1. CONTROL PARAMETERS

EXPOSURE LIMIT VALUES

Exposure limits/standards (Note: Exposure limits are not additive)

Substance Name Form Limit/Standard Note Source

2,6-DI-TERT-BUTYL-P-CRESOL TWA 10 mg/m3 UK EH40
2,6-DI-TERT-BUTYL-P-CRESOL TWA 2 mg/m3 ACGIH
Inhalable
fraction
and
vapour
UK EH40 Workplace Exposure Limits. Exposure limits for use with Control of Substances Hazardous to Health
Regulations 2002 (as amended)

Exposure limits/standards for materials that can be formed when handling this product: When mists/aerosols
can occur the following is recommended: 5 mg/m³ - ACGIH TLV (inhalable fraction).

Note: Information about recommended monitoring procedures can be obtained from the relevant
agency(ies)/institute(s):
UK Health and Safety Executive (HSE)
Product Name: MOBIL DTE OIL LIGHT
Revision Date: 16 May 2017
Page 5 of 13

_____________________________________________________________________________________________________________________
and speed may greatly influence the appropriate action to be taken. For this reason, local experts should be
consulted. Note: Local regulations may prescribe or limit action to be taken.

6.4. REFERENCES TO OTHER SECTIONS

See Sections 8 and 13.

SECTION 7 HANDLING AND STORAGE

7.1. PRECAUTIONS FOR SAFE HANDLING

Prevent small spills and leakage to avoid slip hazard. Material can accumulate static charges which may cause
an electrical spark (ignition source). When the material is handled in bulk, an electrical spark could ignite any
flammable vapors from liquids or residues that may be present (e.g., during switch-loading operations). Use
proper bonding and/or earthing procedures. However, bonding and earthing may not eliminate the hazard from
static accumulation. Consult local applicable standards for guidance. Additional references include American
Petroleum Institute 2003 (Protection Against Ignitions Arising out of Static, Lightning and Stray Currents) or
National Fire Protection Agency 77 (Recommended Practice on Static Electricity) or CENELEC CLC/TR 50404
(Electrostatics - Code of practice for the avoidance of hazards due to static electricity).

Static Accumulator: This material is a static accumulator.

7.2. CONDITIONS FOR SAFE STORAGE, INCLUDING ANY INCOMPATIBILITIES

The type of container used to store the material may affect static accumulation and dissipation. Do not store in
open or unlabelled containers. Keep away from incompatible materials.

7.3. SPECIFIC END USES

Section 1 informs about identified end-uses. No industrial or sector specific guidance available.

SECTION 8 EXPOSURE CONTROLS / PERSONAL PROTECTION

8.1. CONTROL PARAMETERS

EXPOSURE LIMIT VALUES

Exposure limits/standards (Note: Exposure limits are not additive)

Substance Name Form Limit/Standard Note Source

2,6-DI-TERT-BUTYL-P-CRESOL TWA 10 mg/m3 UK EH40
2,6-DI-TERT-BUTYL-P-CRESOL TWA 2 mg/m3 ACGIH
Inhalable
fraction
and
vapour
UK EH40 Workplace Exposure Limits. Exposure limits for use with Control of Substances Hazardous to Health
Regulations 2002 (as amended)

Exposure limits/standards for materials that can be formed when handling this product: When mists/aerosols
can occur the following is recommended: 5 mg/m³ - ACGIH TLV (inhalable fraction).

Note: Information about recommended monitoring procedures can be obtained from the relevant
agency(ies)/institute(s):
UK Health and Safety Executive (HSE)
Product Name: MOBIL DTE OIL LIGHT
Revision Date: 16 May 2017
Page 7 of 13

_____________________________________________________________________________________________________________________

ENVIRONMENTAL CONTROLS
Comply with applicable environmental regulations limiting discharge to air, water and
soil. Protect the environment by applying appropriate control measures to prevent or limit
emissions.

SECTION 9 PHYSICAL AND CHEMICAL PROPERTIES

Note: Physical and chemical properties are provided for safety, health and environmental considerations only
and may not fully represent product specifications. Contact the Supplier for additional information.

9.1. INFORMATION ON BASIC PHYSICAL AND CHEMICAL PROPERTIES

Physical State: Liquid

Colour: Amber
Odour: Characteristic
Odour Threshold: No data available
pH: Not technically feasible
Melting Point: Not technically feasible
Freezing Point: No data available
Initial Boiling Point / and Boiling Range: > 316°C (600°F) [Estimated]
Flash Point [Method]: >200°C (392°F) [ASTM D-92]
Evaporation Rate (n-butyl acetate = 1): No data available
Flammability (Solid, Gas): Not technically feasible
Upper/Lower Flammable Limits (Approximate volume % in air): UEL: 7.0 LEL: 0.9 [Estimated]
Vapour Pressure: < 0.013 kPa (0.1 mm Hg) at 20 °C [Estimated]
Vapour Density (Air = 1): > 2 at 101 kPa [Estimated]
Relative Density (at 15 °C): 0.87 [ASTM D4052]
Solubility(ies): water Negligible
Partition coefficient (n-Octanol/Water Partition Coefficient): > 3.5 [Estimated]
Autoignition Temperature: No data available
Decomposition Temperature: No data available
Viscosity: 32 cSt (32 mm2/sec) at 40ºC | 5 cSt (5 mm2/sec) at 100°C [ASTM D 445]
Explosive Properties: None
Oxidizing Properties: None

9.2. OTHER INFORMATION

Pour Point: -18°C (0°F) [ASTM D97]

DMSO Extract (mineral oil only), IP-346: < 3 %wt

SECTION 10 STABILITY AND REACTIVITY

10.1. REACTIVITY: See sub-sections below.

Product Name: MOBIL DTE OIL LIGHT
Revision Date: 16 May 2017
Page 8 of 13

_____________________________________________________________________________________________________________________

10.2. CHEMICAL STABILITY: Material is stable under normal conditions.

10.3. POSSIBILITY OF HAZARDOUS REACTIONS: Hazardous polymerization will not occur.

10.4. CONDITIONS TO AVOID: Excessive heat. High energy sources of ignition.

10.5. INCOMPATIBLE MATERIALS: Strong oxidisers

10.6. HAZARDOUS DECOMPOSITION PRODUCTS: Material does not decompose at ambient temperatures.

SECTION 11 TOXICOLOGICAL INFORMATION

11.1. INFORMATION ON TOXICOLOGICAL EFFECTS

Hazard Class Conclusion / Remarks

Inhalation
Acute Toxicity: No end point data for Minimally Toxic. Based on assessment of the components.
material.
Irritation: No end point data for material. Negligible hazard at ambient/normal handling temperatures.
Ingestion
Acute Toxicity: No end point data for Minimally Toxic. Based on assessment of the components.
material.
Skin
Acute Toxicity: No end point data for Minimally Toxic. Based on assessment of the components.
material.
Skin Corrosion/Irritation: No end point data Negligible irritation to skin at ambient temperatures. Based on
for material. assessment of the components.
Eye
Serious Eye Damage/Irritation: No end point May cause mild, short-lasting discomfort to eyes. Based on
data for material. assessment of the components.
Sensitisation
Respiratory Sensitization: No end point data Not expected to be a respiratory sensitizer.
for material.
Skin Sensitization: No end point data for Not expected to be a skin sensitizer. Based on assessment of the
material. components.
Aspiration: Data available. Not expected to be an aspiration hazard. Based on physico-
chemical properties of the material.
Germ Cell Mutagenicity: No end point data Not expected to be a germ cell mutagen. Based on assessment of
for material. the components.
Carcinogenicity: No end point data for Not expected to cause cancer. Based on assessment of the
material. components.
Reproductive Toxicity: No end point data Not expected to be a reproductive toxicant. Based on assessment
for material. of the components.
Lactation: No end point data for material. Not expected to cause harm to breast-fed children.
Specific Target Organ Toxicity (STOT)
Single Exposure: No end point data for Not expected to cause organ damage from a single exposure.
material.
Repeated Exposure: No end point data for Not expected to cause organ damage from prolonged or repeated
material. exposure. Based on assessment of the components.
Product Name: MOBIL DTE OIL LIGHT
Revision Date: 16 May 2017
Page 9 of 13

_____________________________________________________________________________________________________________________
TOXICITY FOR SUBSTANCES

NAME ACUTE TOXICITY

2,6-DI-TERT-BUTYL-P-CRESOL Oral Lethality: LD 50 0.89 g/kg (Rat)

OTHER INFORMATION

Contains:
Base oil severely refined: Not carcinogenic in animal studies. Representative material passes IP-346, Modified Ames
test, and/or other screening tests. Dermal and inhalation studies showed minimal effects; lung non-specific infiltration of
immune cells, oil deposition and minimal granuloma formation. Not sensitising in test animals.

SECTION 12 ECOLOGICAL INFORMATION

The information given is based on data available for the material, the components of the material, and similar materials.

12.1. TOXICITY
Material -- Expected to be harmful to aquatic organisms. May cause long-term adverse effects in the aquatic
environment.

12.2. PERSISTENCE AND DEGRADABILITY

Biodegradation:
Base oil component -- Expected to be inherently biodegradable

12.3. BIOACCUMULATIVE POTENTIAL

Base oil component -- Has the potential to bioaccumulate, however metabolism or physical properties may
reduce the bioconcentration or limit bioavailability.

12.4. MOBILITY IN SOIL

Base oil component -- Low solubility and floats and is expected to migrate from water to the land. Expected to
partition to sediment and wastewater solids.

12.5. PERSISTENCE, BIOACCUMULATION AND TOXICITY FOR SUBSTANCE(S)

This product is not, or does not contain, a substance that is a PBT or a vPvB.

12.6. OTHER ADVERSE EFFECTS

No adverse effects are expected.

SECTION 13 DISPOSAL CONSIDERATIONS

Product Name: MOBIL DTE OIL LIGHT
Revision Date: 16 May 2017
Page 10 of 13

_____________________________________________________________________________________________________________________
Disposal recommendations based on material as supplied. Disposal must be in accordance with current applicable
laws and regulations, and material characteristics at time of disposal.

13.1. WASTE TREATMENT METHODS

Product is suitable for burning in an enclosed controlled burner for fuel value or disposal by supervised
incineration at very high temperatures to prevent formation of undesirable combustion products. Protect the
environment. Dispose of used oil at designated sites. Minimize skin contact. Do not mix used oils with solvents,
brake fluids or coolants.

REGULATORY DISPOSAL INFORMATION

European Waste Code: 13 02 05*

NOTE: These codes are assigned based upon the most common uses for this material and may not reflect
contaminants resulting from actual use. Waste producers need to assess the actual process used when
generating the waste and its contaminants in order to assign the proper waste disposal code(s).

This material is considered as hazardous waste pursuant to Directive 91/689/EEC on hazardous waste, and
subject to the provisions of that Directive unless Article 1(5) of that Directive applies.

Empty Container Warning Empty Container Warning (where applicable): Empty containers may contain residue and
can be dangerous. Do not attempt to refill or clean containers without proper instructions. Empty drums should be
completely drained and safely stored until appropriately reconditioned or disposed. Empty containers should be taken
for recycling, recovery, or disposal through suitably qualified or licensed contractor and in accordance with
governmental regulations. DO NOT PRESSURISE, CUT, WELD, BRAZE, SOLDER, DRILL, GRIND, OR EXPOSE
SUCH CONTAINERS TO HEAT, FLAME, SPARKS, STATIC ELECTRICITY, OR OTHER SOURCES OF IGNITION.
THEY MAY EXPLODE AND CAUSE INJURY OR DEATH.

SECTION 14 TRANSPORT INFORMATION

LAND (ADR/RID): 14.1-14.6 Not Regulated for Land Transport

INLAND WATERWAYS (ADNR/ADN): 14.1-14.6 Not Regulated for Inland Waterways Transport

SEA (IMDG): 14.1-14.6 Not Regulated for Sea Transport according to IMDG-Code

SEA (MARPOL 73/78 Convention - Annex II):

14.7. Transport in bulk according to Annex II of MARPOL 73/78 and the IBC Code
Not classified according to Annex II

AIR (IATA): 14.1-14.6 Not Regulated for Air Transport

SECTION 15 REGULATORY INFORMATION

Product Name: MOBIL DTE OIL LIGHT
Revision Date: 16 May 2017
Page 11 of 13

_____________________________________________________________________________________________________________________

REGULATORY STATUS AND APPLICABLE LAWS AND REGULATIONS

Listed or exempt from listing/notification on the following chemical inventories: AICS, DSL, ENCS,
IECSC, KECI, PICCS, TSCA

15.1. SAFETY, HEALTH AND ENVIRONMENTAL REGULATIONS/LEGISLATION SPECIFIC FOR THE

SUBSTANCE OR MIXTURE

Applicable EU Directives and Regulations:

1907/2006 [... on the Registration, Evaluation, Authorisation and Restriction of Chemicals ... and
amendments thereto]
1272/2008 [on classification, labelling and packaging of substances and mixtures.. and amendments
thereto]

15.2. CHEMICAL SAFETY ASSESSMENT

REACH Information: A Chemical Safety Assessment has been carried out for one or more substances present in the
material.

SECTION 16 OTHER INFORMATION

REFERENCES: Sources of information used in preparing this SDS included one or more of the following: results from
in house or supplier toxicology studies, CONCAWE Product Dossiers, publications from other trade associations, such
as the EU Hydrocarbon Solvents REACH Consortium, U.S. HPV Program Robust Summaries, the EU IUCLID Data
Base, U.S. NTP publications, and other sources, as appropriate.

List of abbreviations and acronyms that could be (but not necessarily are) used in this safety data sheet:
Acronym Full text
N/A Not applicable
N/D Not determined
NE Not established
VOC Volatile Organic Compound
AICS Australian Inventory of Chemical Substances
AIHA WEEL American Industrial Hygiene Association Workplace Environmental Exposure Limits
ASTM ASTM International, originally known as the American Society for Testing and Materials (ASTM)
DSL Domestic Substance List (Canada)
EINECS European Inventory of Existing Commercial Substances
ELINCS European List of Notified Chemical Substances
ENCS Existing and new Chemical Substances (Japanese inventory)
IECSC Inventory of Existing Chemical Substances in China
KECI Korean Existing Chemicals Inventory
Product Name: MOBIL DTE OIL LIGHT
Revision Date: 16 May 2017
Page 8 of 13

_____________________________________________________________________________________________________________________

10.2. CHEMICAL STABILITY: Material is stable under normal conditions.

10.3. POSSIBILITY OF HAZARDOUS REACTIONS: Hazardous polymerization will not occur.

10.4. CONDITIONS TO AVOID: Excessive heat. High energy sources of ignition.

10.5. INCOMPATIBLE MATERIALS: Strong oxidisers

10.6. HAZARDOUS DECOMPOSITION PRODUCTS: Material does not decompose at ambient temperatures.

SECTION 11 TOXICOLOGICAL INFORMATION

11.1. INFORMATION ON TOXICOLOGICAL EFFECTS

Hazard Class Conclusion / Remarks

Inhalation
Acute Toxicity: No end point data for Minimally Toxic. Based on assessment of the components.
material.
Irritation: No end point data for material. Negligible hazard at ambient/normal handling temperatures.
Ingestion
Acute Toxicity: No end point data for Minimally Toxic. Based on assessment of the components.
material.
Skin
Acute Toxicity: No end point data for Minimally Toxic. Based on assessment of the components.
material.
Skin Corrosion/Irritation: No end point data Negligible irritation to skin at ambient temperatures. Based on
for material. assessment of the components.
Eye
Serious Eye Damage/Irritation: No end point May cause mild, short-lasting discomfort to eyes. Based on
data for material. assessment of the components.
Sensitisation
Respiratory Sensitization: No end point data Not expected to be a respiratory sensitizer.
for material.
Skin Sensitization: No end point data for Not expected to be a skin sensitizer. Based on assessment of the
material. components.
Aspiration: Data available. Not expected to be an aspiration hazard. Based on physico-
chemical properties of the material.
Germ Cell Mutagenicity: No end point data Not expected to be a germ cell mutagen. Based on assessment of
for material. the components.
Carcinogenicity: No end point data for Not expected to cause cancer. Based on assessment of the
material. components.
Reproductive Toxicity: No end point data Not expected to be a reproductive toxicant. Based on assessment
for material. of the components.
Lactation: No end point data for material. Not expected to cause harm to breast-fed children.
Specific Target Organ Toxicity (STOT)
Single Exposure: No end point data for Not expected to cause organ damage from a single exposure.
material.
Repeated Exposure: No end point data for Not expected to cause organ damage from prolonged or repeated
material. exposure. Based on assessment of the components.
Product Name: MOBIL DTE OIL LIGHT
Revision Date: 16 May 2017
Page 13 of 13

_____________________________________________________________________________________________________________________
Section 08: OEL Table - Form Column - Header information was added.
Section 08: OEL Table - Limit Column - Header information was added.
Section 08: OEL Table - Notation Column - Header information was added.
Section 08: OEL Table - Source Column - Header information was added.
Section 08: OEL Table - Substance Name Column - Header information was added.
Section 09: Pour Point ºC(ºF) information was modified.
Section 09: Relative Density information was modified.
Section 09: Vapour Pressure information was modified.
Section 11 Acute Toxicity data - Header information was added.
Section 11 Substance Name - Header information was added.
Section 11 Substance Toxicity table - Header information was added.
Section 11 Substance Toxicology table information was added.
Section 12: Ecological Information - Acute Aquatic Toxicity information was added.
Section 12: Ecological Information - Acute Aquatic Toxicity information was deleted.
Section 15: EU Directives and Regulations information was modified.
Section 15: Labeling - Header information was modified.
Section 16: Classification CLP/GHS Table information was added.
Section 16: HCode Key information was added.

-----------------------------------------------------------------------------------------------------------------------------------------------------
The information and recommendations contained herein are, to the best of ExxonMobil's knowledge and belief, accurate
and reliable as of the date issued. You can contact ExxonMobil to insure that this document is the most current
available from ExxonMobil. The information and recommendations are offered for the user's consideration and
examination. It is the user's responsibility to satisfy itself that the product is suitable for the intended use. If buyer
repackages this product, it is the user's responsibility to insure proper health, safety and other necessary information is
included with and/or on the container. Appropriate warnings and safe-handling procedures should be provided to
handlers and users. Alteration of this document is strictly prohibited. Except to the extent required by law, re-
publication or retransmission of this document, in whole or in part, is not permitted. The term, "ExxonMobil" is used for
convenience, and may include any one or more of ExxonMobil Chemical Company, Exxon Mobil Corporation, or any
affiliates in which they directly or indirectly hold any interest.

-----------------------------------------------------------------------------------------------------------------------------------------------------

Internal Use Only

MHC: 0B, 0B, 0, 0, 0, 0 PPEC: A

DGN: 2007066QGB (547708)

-----------------------------------------------------------------------------------------------------------------------------------------------------

ANNEX
Annex not required for this material.