Scribd
Upload
199 views2 pages

Router Configuration With Cisco Packet Tracer

This document describes how to configure a simple network with a router and two PCs. It provides steps to configure the router interfaces with IP addresses, and connect each PC to a different router interface. It also describes configuring the PCs by assigning each one an IP address, subnet mask, and default gateway matching its connection to the router. Configuration tables show the assigned addresses for each network device. The goal is to demonstrate how the router routes data between the two PCs.

Uploaded by

Marinette Medrano
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
199 views2 pages

Router Configuration With Cisco Packet Tracer

This document describes how to configure a simple network with a router and two PCs. It provides steps to configure the router interfaces with IP addresses, and connect each PC to a different router interface. It also describes configuring the PCs by assigning each one an IP address, subnet mask, and default gateway matching its connection to the router. Configuration tables show the assigned addresses for each network device. The goal is to demonstrate how the router routes data between the two PCs.

Uploaded by

Marinette Medrano
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

IT312- Networking 2

Chapter 3- Routing and Switching – Configuring a Network Switch

Router Configuration with Cisco Packet Tracer

In this network, a router and 2 PCs are used. Computers are connected with routers using a
copper straight-through cable. After forming the network, to check network connectivity a simple PDU is
transferred from PC0 to PC1. The network simulation status is successful. From this network, it can be
observed that the router handles data transfers between multiple devices.

Procedure:

Step-1(Configuring Router1):

1. Select the router and Open CLI.


2. Press ENTER to start configuring Router1.
3. Type enable to activate the privileged mode.
4. Type config t(configure terminal) to access the configuration menu.
5. Configure interfaces of Router1:

• Type interface FastEthernet0/0 to access FastEthernet0/0 and Configure the FastEthernet0/0


interface with the IP address 192.168.10.1 and Subnet mask 255.255.255.0.

• Type interface FastEthernet0/1 to access GigabitEthernet0/0 and Configure the FastEthernet0/1


interface with IP address 192.168.20.1 and Subnet mask 255.255.255.0.
6. Type no shutdown to finish.

Router1 Command Line Interface:


1. Router>enable
2. Router#config t
3. Enter configuration commands, one per line. End with CNTL/Z.
4. Router(config)#interface FastEthernet0/0
5. Router(config-if)#ip address 192.168.10.1 255.255.255.0
6. Router(config-if)#no shutdown
7. Router(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state to up
8. Router(config-if)#interface FastEthernet0/1
9. Router(config-if)#ip address 192.168.20.1 255.255.255.0
10. Router(config-if)#no shutdown

Step-2(Configuring PCs):
1. Assign IP Addresses to every PC in the network.
2. Select the PC, Go to the desktop and select IP Configuration and assign an IP address, Default
gateway, Subnet Mask
3. Assign the default gateway of PC0 as 192.168.10.1.
4. Assign the default gateway of PC1 as 192.168.20.1.

Step-3(Connecting PCs with Router):


1. Connect FastEthernet0 port of PC0 with FastEthernet0/0 port of Router1 using a copper straight-
through cable.
2. Connect FastEthernet0 port of PC1 with FastEthernet0/1 port of Router1 using a copper straight-
through cable.

Page 1 of 2
IT312- Networking 2
Chapter 3- Routing and Switching – Configuring a Network Switch

Router Configuration Table:

Device IP address IP Address


Name FastEthernet0/0 Subnet Mask FastEthernet0/1 Subnet Mask

Router1 192.168.10.1 255.255.255.0 192.168.20.1 255.255.255.0

PC Configuration Table:

Device Name IP address Subnet Mask Gateway

PC 0 192.168.10.2 255.255.255.0 192.168.10.1

PC 1 192.168.20.2 255.255.255.0 192.168.20.1

Designed Network topology:

Page 2 of 2

You might also like