Operating instructions

For the operator

Operating instructions

ecoFIT pure
412 - 435

GB, IE

Publisher/manufacturer
Vaillant GmbH
Berghauser Str. 40 D-42859 Remscheid
Tel. +49 21 91 18‑0 Fax +49 21 91 18‑2810
[email protected] www.vaillant.de
Contents
Contents 6 Care and maintenance ................ 9
6.1 Maintenance .................................. 9
1 Safety ............................................ 3 6.2 Caring for the product .................... 9
1.1 Action-related warnings ................. 3 6.3 Reading maintenance
1.2 Intended use .................................. 3 messages ...................................... 9
2 Notes on the documentation ...... 4 6.4 Checking the condensate drain
2.1 Observing other applicable pipework and tundish................... 10
documents ..................................... 4 7 Decommissioning...................... 10
2.2 Storing documents......................... 4 7.1 Temporarily decommissioning
2.3 Applicability of the instructions....... 4 the product................................... 10
3 Product description..................... 4 7.2 Permanently decommissioning
3.1 Front view ...................................... 4 the product................................... 10
3.2 Control elements............................ 4 8 Recycling and disposal............. 10
3.3 Displayed symbols......................... 5 9 Guarantee and customer
service ........................................ 10
3.4 Information on the identification
plate ............................................... 5 9.1 Guarantee.................................... 10
3.5 Serial number ................................ 5 9.2 Customer service......................... 10
3.6 CE label ......................................... 6 Appendix ............................................... 11
3.7 Benchmark..................................... 6 A Status codes – Overview........... 11
4 Operation...................................... 6 B Troubleshooting ........................ 11
4.1 Operating concept ......................... 6
4.2 Basic display.................................. 7
4.3 Adjustment and display levels ....... 7
4.4 Cabinet-type casing ....................... 7
4.5 Opening the isolator devices ......... 7
4.6 Starting up the product .................. 7
4.7 Switching on the product ............... 7
4.8 Setting the heating flow
temperature ................................... 7
4.9 Setting the hot water
temperature ................................... 8
4.10 Switching off the product's
functions ........................................ 8
4.11 Protecting the heating installation
against frost ................................... 8
4.12 Switching the product to standby
mode.............................................. 9
5 Troubleshooting .......................... 9
5.1 Detecting and rectifying faults........ 9
5.2 Calling up (Live monitor) status
codes ............................................. 9

2 Operating instructions ecoFIT pure 0020230536_01

 Safety 1
1 Safety ing installations and for hot wa-
1.1 Action-related warnings ter generation.
Classification of action-re- Intended use includes the fol-
lated warnings lowing:
The action-related warnings – observance of the operating
are classified in accordance instructions included for the
with the severity of the pos- product and any other system
sible danger using the following components
warning signs and signal words: – compliance with all inspection
Warning symbols and signal and maintenance conditions
words listed in the instructions.
Danger! This product can be used by
Imminent danger to life children aged from 8 years
or risk of severe personal and above and persons with
injury reduced physical, sensory or
Danger! mental capabilities or lack of
experience and knowledge if
Risk of death from electric
they have been given supervi-
shock
sion or instruction concerning
Warning. use of the product in a safe way
Risk of minor personal and understand the hazards in-
injury volved. Children must not play
Caution. with the product. Cleaning and
Risk of material or envir- user maintenance work must
onmental damage not be carried out by children
unless they are supervised.
1.2 Intended use
Any other use that is not spe-
There is a risk of injury or death
cified in these instructions, or
to the user or others, or of dam-
use beyond that specified in this
age to the product and other
document shall be considered
property in the event of im-
improper use. Any direct com-
proper use or use for which it
mercial or industrial use is also
is not intended.
deemed to be improper.
The product is intended as a
Caution.
heat generator for closed heat-
Improper use of any kind is
prohibited.

0020230536_01 ecoFIT pure Operating instructions 3

2 Notes on the documentation
2 Notes on the 3 Product description
documentation 3.1 Front view
2.1 Observing other applicable
documents 1

▶ You must observe all operating instruc-

tions enclosed with the system compon-
ents. 2

2.2 Storing documents

▶ Keep this manual and all other applic- 1 Control elements 2 Plate with serial
able documents safe for future use. number on the
rear
2.3 Applicability of the
instructions 3.2 Control elements
These instructions apply only to: 3

Product article number

Article Gas Coun-
50
number cil Number
VU 126/6-3 OV 0010020400 41-694-08
(H-GB)
VU 156/6-3 OV 0010020401 41-694-09
(H-GB)
2 1
VU 186/6-3 OV 0010020402 41-694-10
(H-GB) 1 Fault clearance 2 Operating but-
VU 256/6-3 OV 0010020403 41-694-11 key tons
(H-GB) 3 Display
VU 306/6-3 OV 0010020404 41-694-12
(H-GB)
VU 356/6-3 OV 0010020405 41-694-19
(H-GB)

4 Operating instructions ecoFIT pure 0020230536_01

 Product description 3
3.2.1 Operator control panel Sym- Meaning Explanation
bol
Heating mode – Permanently
active on: Heating
mode heat
requirement
1
– Flashing:
Burner on in
9
50 2
Maintenance re-
heating mode
Information on
8
quired the maintenance
3 message in the
"Live Monitor"
7 Summer mode
4
active
Heating mode is
switched off
Burner anti-cyc- To avoid the
6 ling time is active need for frequent
switching on and
5 off (increases the
product's working
life).
Fault in the Fault in the
1 Current heating 5 Fault clearance product product. Appears
flow temperat- key F.XX
instead of the
ure, operating 6 Maximum out- basic display.
mode, fault code put (only used
or additional in- for Austria,
3.4 Information on the
formation Germany and
2 Current assign- Switzerland) identification plate
ment of the right- 7 Access to the The identification plate is mounted on the
hand selection menu for addi- underside of the product in the factory.
button tional information
3 Left- and right- 8 Current assign- The identification plate keeps record of
hand selection ment of the left- the country in which the product is to be
buttons hand selection installed.
4 and but- button
ton 9 Active operating 3.5 Serial number
status
The serial number is located on a plastic
plate at the bottom of the front casing.
3.3 Displayed symbols
Sym- Meaning Explanation
bol
Burner operating Burner on
correctly

0020230536_01 ecoFIT pure Operating instructions 5

4 Operation
3.6 CE label who should, on receipt, write the Notifica-
tion Number on the Benchmark Checklist.
This product should be serviced regularly
  to optimise its safety, efficiency and per-
The CE label shows that the products formance. The service engineer should
comply with the basic requirements of the complete the relevant Service Record on
applicable directives as stated on the iden- the Benchmark Checklist after each ser-
tification plate. vice.
The declaration of conformity can be The Benchmark Checklist will be required
viewed at the manufacturer's site. in the event of any warranty.
3.7 Benchmark
4 Operation
4.1 Operating concept
Op- Function
erator
control
element
Vaillant is a licensed member of the
– Setting the hot water temperat-
Benchmark Scheme which aims to im- ure
prove the standards of installation and – Cancelling the activation of an
commissioning of domestic heating and operating mode
hot water systems in the UK and to en- – Cancelling a change to a set
courage regular servicing to optimise value
safety, efficiency and performance. – Going one selection level
higher
Benchmark is managed and promoted
by the Heating and Hotwater Industry – Setting the heating flow tem-
perature
Council. For more information visit
– Reading the system pressure
www.benchmark.org.uk.
– Activating the comfort mode
▶ Please ensure that the installer has fully – Activating the operating mode
completed the Benchmark Checklist on – Confirm setting
the inside back pages of the installation – Going one selection level lower
instructions supplied with the product + – Calling up the menu
and that you have signed it to say that at the
you have received a full and clear ex- same
planation of its operation. The installer time
is legally required to complete a com- or – Reducing or increasing the set
missioning checklist as a means of value
complying with the appropriate Build- – Scrolling through menu entries
ing Regulations (England and Wales). The current function of the and but-
All installations must be notified to Local tons is shown in the display.
Area Building Control either directly or Adjustable values are always displayed as
through a Competent Persons Scheme. flashing.
A Building Regulations Compliance Certi-
You must always confirm a change to a
ficate will then be issued to the customer
value. Only then is the new setting saved.

6 Operating instructions ecoFIT pure 0020230536_01

 Operation 4
You can press to cancel a procedure at 4.4 Cabinet-type casing
any time.
Enclosing the product in cabinet-type cas-
4.2 Basic display ing requires compliance with the applic-
able design instructions.
If you require cabinet-type casing for your
50 product, consult a heating specialist com-
pany. Never, under any circumstances,
enclose the product yourself.

4.5 Opening the isolator devices

The basic display shows the current condi- 1. Ask the competent person who in-
tion of the product. If you press a selection stalled the product to explain to you
button, the activated function is displayed where these isolator devices are loc-
in the display. ated and how to handle them.
The functions that are available depend 2. Open the gas isolator cock fully.
on whether a controller is connected to the 3. Open the service valves in the heating
product. installation's flow and return.
You can switch back to the basic display Applicability: Product with connected domestic hot
by: water cylinder

– Pressing to exit the selection levels ▶ Open the cold water stop valve.
– Not pressing any button for longer than
15 minutes. 4.6 Starting up the product
If there is an error message present, the ▶ Only start up the product once the cas-
basic displays switches to the error mes- ing has been completely closed.
sage.
4.7 Switching on the product
4.3 Adjustment and display levels ▶ Switch on the product via the main
The product has two adjustment and switch installed on-site.
display levels.
4.8 Setting the heating flow
The end user level contains information
temperature
and setting options that you require as the
end user. 1. Press ( ).
The installer level is reserved for the com- ◁ The target value of the heating flow
petent person. It is protected by a code. temperature appears on the display.
Only competent persons may change any
settings in the installer level. Note
The competent person may
have adjusted the maximum
possible temperature.

Conditions: No controller connected

▶ Use or to set the required heating

flow temperature.
▶ Confirm by pressing .

0020230536_01 ecoFIT pure Operating instructions 7

4 Operation
Conditions: Controller connected 4.10 Switching off the product's
▶ Set the maximum possible heating flow functions
temperature on the product. 4.10.1 Switching off heating mode
▶ Confirm by pressing . (Summer mode)
▶ Set the required heating flow temperat- 1. To switch off heating mode without
ure on the controller (→ Controller oper- switching off the hot water generation,
ating instructions). press ( ).
4.9 Setting the hot water ◁ The value of the heating flow tem-
temperature perature appears in the display.
2. Use the button to set the heating
Warning.
flow temperature to Off.
Risk of being scalded by hot
3. Confirm by pressing .
water.
◁ Heating mode is switched off.
To protect against Legionella, ◁ The symbol appears in the
the hot water can be heated up display.
to above 60 °C at pre-defined
times. 4.11 Protecting the heating
installation against frost
▶ Have a competent person
inform you about the meas- 4.11.1 Frost protection function
ures that should be taken to Caution.
protect against Legionella in Risk of material damage due
your system. to frost.
The frost protection function
1. Press ( ).
cannot guarantee flow through
◁ The set hot water temperature
the entire heating installation,
flashes in the display.
which means that parts of the
Conditions: No controller connected heating installation may freeze
▶ Change the hot water temperature by
and therefore become dam-
pressing or . aged.
▶ Confirm by pressing . ▶ During a period of frost, en-
Conditions: Controller connected sure that the heating installa-
tion remains in operation and
▶ Use to set the maximum possible hot
that all rooms are sufficiently
water temperature on the product.
▶ Confirm by pressing . heated, even when you are
▶ Set the required hot water temperature away.
on the controller (→ Controller operating
instructions). Note
To keep the frost protection
devices active, you should switch
your product on and off using the
controller, if one is provided.

8 Operating instructions ecoFIT pure 0020230536_01

 Troubleshooting 5
If the heating flow temperature falls be- 5.2 Calling up (Live monitor)
low 5 °C when the on/off button is on, the status codes
product comes into operation and heats
the circulating water to approx. 30 °C on
▶ Press and at the same time.
Status codes – Overview (→ Page 11)
both the heating side and the hot water
side (if available). ◁ The current operating status (status
code) is shown on the display.
4.11.2 Draining the heating
installation
When the unit is switched off for an exten-
6 Care and maintenance
ded period, frost protection can be guar- 6.1 Maintenance
anteed by completely draining the heating
An annual inspection of the product carried
installation and the product.
out by a competent person is a prerequis-
▶ Consult a competent person about this. ite for ensuring that the product is perman-
ently ready and safe for operation, reliable,
4.12 Switching the product to
and has a long working life.
standby mode
▶ Press the fault clearance key for less 6.2 Caring for the product
than three seconds.
Caution.
◁ The display shows OFF and goes Risk of material damage
out. caused by unsuitable clean-
◁ The product is now in standby mode.
ing agents.
◁ The product's frost protection func-
tion is activated. ▶ Do not use sprays, scouring
◁ The main power supply is not inter- agents, detergents, solvents
rupted. The product continues to be or cleaning agents that con-
supplied with power. tain chlorine.

▶ Clean the casing with a damp cloth and

5 Troubleshooting a little solvent-free soap.
5.1 Detecting and rectifying faults 6.3 Reading maintenance
▶ If faults occur or fault messages are messages
displayed (F.xx), proceed as set out in
If the symbol is shown in the display, the
the table in the appendix.
product requires maintenance work.
Troubleshooting (→ Page 11)
▶ If the product is not functioning cor- The product is not in fault mode but contin-
rectly, contact a competent person. ues to operate.
▶ Consult a competent person about this.
▶ If the water pressure is flashing at the
same time, simply add more heating
water.

0020230536_01 ecoFIT pure Operating instructions 9

7 Decommissioning
6.4 Checking the condensate 7.2 Permanently
drain pipework and tundish decommissioning the product
The condensate drain pipework and tun- ▶ Have a competent person permanently
dish must always be penetrable. decommission the product.
▶ Regularly check the condensate drain
pipework and tundish for faults and,
particularly, for blockages.
8 Recycling and disposal
You must not be able to see or feel any ▶ The competent person who installed
obstructions in the condensate drain pipe- your product is responsible for the dis-
work and tundish. posal of the packaging.
▶ If you notice a fault, have it rectified by
a competent person. If the product is identified with this
symbol:
▶ In this case, do not dispose of the
7 Decommissioning product with the household waste.
7.1 Temporarily decommissioning
▶ Instead, hand in the product to a collec-
tion centre for old electrical or electronic
the product appliances.
Caution.
Risk of material damage due If the product contains batteries that
to frost. are marked with this symbol, these bat-
teries may contain substances that are
The frost protection and mon- hazardous to human health and the envir-
itoring devices are only active onment.
while the unit is connected to ▶ In this case, dispose of the batteries at
the power mains and switched a collection point for batteries.
on via the on/off button, and
when the gas isolator cock is
open. 9 Guarantee and customer
▶ Temporarily decommission service
the product only if no frost is 9.1 Guarantee
expected. For information on the manufacturer's
guarantee, you can write to the contact
▶ Temporarily decommission the product address that is provided on the back page.
only if no frost is expected.
▶ Switch off the product via the main 9.2 Customer service
switch installed on-site. To ensure regular servicing, it is strongly
◁ The display goes out. recommended that arrangements are
▶ When decommissioning the product made for a Maintenance Agreement.
for a prolonged period (e.g. holiday), Please contact Vaillant Service Solutions
close the gas isolator cock and also, for for further details:
combination products, the cold water Telephone: 0330 100 3461
stop valve.

10 Operating instructions ecoFIT pure 0020230536_01

 Appendix
Appendix
A Status codes – Overview
Status codes that are not listed here can be viewed in the installation instructions.
Status code Meaning
Displays in heating mode
S.00 Heating: No heat demand
S.02 Heating mode: Pump pre-run
S.03 Heating mode: Ignition
S.04 Heating mode: Burner on
S.06 Heating mode: Fan overrun
S.07 Heating mode: Pump overrun
S.08 Heating, remaining anti-cycling time xx mins
Displays in cylinder charging mode (product with hot water generation through external
domestic hot water cylinder)
S.20 Hot water requirement
S.22 DHW mode: Pump pre-run
S.24 DHW mode: Burner on
Other displays
S.31 No heat demand: Summer mode
S.34 Heating mode: Frost protection
S.46 Comfort protection mode, flame loss at minimum load

B Troubleshooting
Fault Cause Measure
Product does not The gas isolator cock installed on-site Open both gas isolator cocks.
start up: and/or the gas isolator cock on the
– No hot water product is closed.
– Heating re- The power supply in the building is dis- Check the fuse in the building.
mains cold connected. The product switches on automat-
ically when the power is restored.
The product is switched off. Switch on the product.
The heating flow temperature is set Set the heating flow and hot water
too low or to the Heating off position, temperature.
and/or the hot water temperature is set
too low.
There is air in the heating installation. Have a competent person purge
the heating installation.

0020230536_01 ecoFIT pure Operating instructions 11

Appendix
Fault Cause Measure
Product does not After three unsuccessful ignition at- Press the fault clearance key for
start up: tempts, the product switches to fault one second. The product makes
– No hot water mode (fault message: F.28). another attempt to ignite the
flame.
– Heating re-
mains cold If you have been unable to elim-
inate the ignition fault after three
fault clearance attempts, consult a
competent person.
There is a fault in the flue gas route. Have a competent person rectify
the fault.
Heating does not The external controller is not set cor- Set the external controller cor-
start. rectly. rectly (→ Controller operating in-
structions).

12 Operating instructions ecoFIT pure 0020230536_01

0020230536_01 10.10.2016

supplier
Vaillant Ltd.
Nottingham Road Belper Derbyshire DE56 1JT
Telephone 0330 100 3461
[email protected] www.vaillant.co.uk

© These instructions, or parts thereof, are protected by copyright and may be

reproduced or distributed only with the manufacturer's written consent.
We reserve the right to make technical changes.
 This file was downloaded from the site
mans.io

Instruction manuals and user guides

Samsung
Pioneer
Alpine
LG
Dell
Sharp
Sony
Philips
Epson
Netgear