UTC U2429 CMOS IC

SERIAL DATA CONTROL DUAL

ELECTRONIC VOLUME
DESCRIPTION
The UTC U2429 is a dual channel electronic volume
controlled with 2-wire serial data.
SOP-8
The built-in reference circuit can compose of an
electronic volume with less external parts.

FEATURES
* Built-in reference circuit
* Control with serial data
Volume 0 ~ -83dB (1dB/step), -∞
(Independent control is allowed in each channel)
DIP-8
* Low noise and low distortion
VNO = 5µVrms (ATT = -∞)
THD = 0.01% Typ. (V0 = 0.5Vrms)

PIN CONFIGURATION

VIN1 1 8 VIN2

VOUT1 2 7 VOUT2

GND 3 6 VCC

DATA 4 5 CLOCK

PIN DESCRIPTION
PIN No. PIN NAME FUNCTION
1 VIN 1 1-ch input pin
2 VOUT1 1-ch output pin
3 GND Ground pin
4 DATA Control data input pin. Inputs data in synchronization with clock.
5 CLOCK Clock input pin for transferring serial data.
6 VCC Power supply pin. Stabilize the pin with decoupling capacitor.
7 VOUT2 2-ch output pin
8 VIN2 1-ch input pin

UTC UNISONIC TECHNOLOGIES CO., LTD. 1

QW-R502-031,A
UTC U2429 CMOS IC
BLOCK DIAGRAM
VIN2 VOUT2 VCC CLOCK
8 7 6 5

VR 2 +

VOL AMP 2 + LOGIC

Vref CONTROL
-

VOL AMP 1
REF AMP

VR 1 +

1 2 3 4
VIN1 VOUT1 GND DATA

ABSOLUTE MAXIMUM RATINGS

PARAMETER SYMBOL RATINGS UNIT
Supply Voltage VCC, VDD 6.0 V
Power Dissipation
DIP-8 PD 625 mW
SOP-8 440
Operating Temperature Topr -20 ~ +75 ℃
Storage Temperature Tstg -55 ~ +125 ℃

RECOMMENDED OPERATING CONDITIONS

PARAMETER SYMBOL RATINGS UNIT
Supply voltage range Vcc 4.5 ~ 5.5 V
Rated supply voltage Vcc 5 V

ELECTRICAL CHARACTERISTICS (VCC = 5V, Ta= 25℃, unless otherwise noted.)

PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNIT
Circuit current ICC 8 16 mA
Maximum attenuation ATT ATT=-∞ -90 -80 dB
Attenuation error ATT ATT=0 -2.0 0 2.0 dB
Maximum input voltage VIM THD=1%, ATT=-6dB 1.5 1.7 Vrms
Maximum output voltage VOM THD=1% 0.8 1.3 Vrms
Output noise voltage VNO1 ATT=0, Rg=0 4 10 μVrms
VNO2 ATT=-∞, Rg=0 5 10 μVrms
Total harmonic distortion THD f=1kHz, VO=0.5Vrms, ATT=0 0.01 0.05 %
Channel separation CS f=1kHz -80 -70 dB

UTC UNISONIC TECHNOLOGIES CO., LTD. 2

QW-R502-031,A
UTC U2429 CMOS IC
DC CHARACTERISTICS OF DIGITAL BLOCK
PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNIT
"L" level input voltage VIL Data, clock pin 0 ~ 0.2VCC V
"H" level input voltage VIH 0.8VCC ~ VCC V
"L" level input current IIL VI=0 Data, clock pin -10 10 μA
"H" level input current IIH VI=5V 10 μA

AC CHARACTERISTICS OF DIGITAL BLOCK

PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNIT
Cycle time of clock tcr VDD=5V 4 μs
Pulse width of clock ("H" level) tWHC VDD=5V 1.6 μs
Pulse width of clock ("L" level) tWLC VDD=5V 1.6 μs
Clock rising time tr VDD=5V 0.4 μs
Clock falling time tf VDD=5V 0.4 μs
Data setup time tSD VDD=5V 0.8 μs
Data hold time tHD VDD=5V 0.8 μs

RELATIONSHIP BETWEEN DATA AND CLOCK

CLOCK

D0 D1 D2 D3
DATA

Reads data signal at the rising edge of clock signal

D8 D9 D10

Latch signal "H"

Reads latch signal at the falling edge of clock

UTC UNISONIC TECHNOLOGIES CO., LTD. 3

QW-R502-031,A
UTC U2429 CMOS IC
SYSTEM CONFIGURATION

UTC U2429

2ch IN 2ch OUT

VOLUME

1ch IN 1ch OUT

VOLUME
LOGIC
CONTROL

DATA CLOCK

CLOCK AND DATA TIMING

tcr

75%
CLOCK
25%

tr tf

tWHC tWLC

DATA

tSD tHD

UTC UNISONIC TECHNOLOGIES CO., LTD. 4

QW-R502-031,A
UTC U2429 CMOS IC
DATA INPUT FORMAT

D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 D10

0/1 0/1 VOLUME 1 1

0: Both channels at a time

1: A channel at a time

0:1CH
1:2CH

VOLUME CODE
ATT1 D2 D3 D4 D5 D6 ATT2 D7 D8
0dB H L H L H 0dB H H
-4dB L L H L H -1dB L H
-8dB H H L L H -2dB H L
-12dB L H L L H -3dB L L
-16dB H L L L H
-20dB L L L L H
-24dB H H H H L
-28dB L H H H L
-32dB H L H H L
-36dB L L H H L
-40dB H H L H L
-44dB L H L H L
-48dB H L L H L
-52dB L L L H L
-56dB H H H L L
-60dB L H H L L
-64dB H L H L L
-68dB L L H L L
-72dB H H L L L
-76dB L H L L L
-80dB H L L L L
L L L L L

UTC assumes no responsibility for equipment failures that result from using products at values that
exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or
other parameters) listed in products specifications of any and all UTC products described or contained
herein. UTC products are not designed for use in life support appliances, devices or systems where
malfunction of these products can be reasonably expected to result in personal injury. Reproduction in
whole or in part is prohibited without the prior written consent of the copyright owner. The information
presented in this document does not form part of any quotation or contract, is believed to be accurate
and reliable and may be changed without notice.

UTC UNISONIC TECHNOLOGIES CO., LTD. 5

QW-R502-031,A