l12 - Time and Synchronization v22

FYS3240- 4240
Data acquisition & control
Time and synchronization
Spring 2022– Lecture #12
Bekkeng, 30.12.2021
Why is time and synchronization so
important?
• Some examples:
– Accurate time stamping of scientific data
– In financial trading we must know the time accurately.
– Important to reduce confusion in shared file systems.
– Update databases (in parallel).
– Tracking security breaches or network usage requires accurate
timestamps in logs.
– Used in electric power systems (fault recorders, billing meters,
etc.).
– Necessary in telecommunication networks.
– Global Navigation Satellite Systems (GNSS), such as GPS,
requires very accurate clock synchronization for position
calculations.
TU-artikkel : GPS mer enn bare navigasjon

How accurate much the clock be ?
• Depends on the application.
• If the clock in the GPS receiver have an error of 1 ms relative to

the atomic clocks in the GPS satellites this corresponds to a
position error of 𝛿p = c * 𝛿t = 3*108 m/s * 1 ms = 300 km.
Position, navigation & timing (PNT)
• PNT is important in
many applications!
På rett sted til rett tid (regjeringen.no)

How good is a crystal oscillator (XO) ?
• Interested in the long-term measurement stability and
accuracy
• Watch crystal oscillator: about 20 ppm, or worse

– Error > 1.73 s in 24 hours (almost 1 minute drift in one month)
• The accuracy can be improved using a:

– Temperature compensated crystal oscillator (TCXO)
– Oven controlled crystal oscillator (OCXO)
• the oscillator is enclosed in a temperature controlled oven
• Some DAQ card accuracy examples:

– TCXO : 1 ppm
– OCXO: 50 ppb
Chip Scale Atomic Clock (CSAC)
• Two orders of magnitude better accuracy
than oven-controlled crystal oscillators
(OCXOs).
• Can keep track of the time if GPS-signals
are lost (e.g. inside a building, or due to
jamming).
• Example: Microsemi CSAC

– < 120 mW power consumption
– < 17 cm3 volume
– 35 g weight
– two outputs; a 10 MHz square wave and
1 PPS (Pulse Per Second) The frequency of the TCXO is continuously
compared and corrected to ground state
– Maintains time-of-day (TOD) as a 32-bit hyperfine frequency of the cesium atoms,
unsigned integer contained in the “physics package”, which
– Can set the TOD thereby improves the stability and
environmental sensitivity of the TCXO.
Computer clocks
• Hardware clocks
– Real Time Clock (RTC) is an integrated circuit on the motherboard.
– The RTC has a battery backup power so that it tracks the time even
while the computer is turned off.
– Based on a 32.768 kHz quartz crystal oscillator.
– Maximum resolution of 1 millisecond (1 kHz).
• Software clocks
– Maintained by the operating system, based on the RTC interrupts.
– When the system starts it sets the system time to a value based on the
real-time clock of the computer and then regularly updates the time
based on interrupts from the RTC.
Computer clock drift
• The software clock is a bad timekeeper (without corrections)!
• The computer clock drifts away from the correct time. At the time of
synchronization with a time server the clock is reset to the “correct
time” (but with a small offset).
• Could update the computer clock often (using NTP or PTP), or
read time directly from a timing card connected to a GPS
antenna, IRIG-B signal or an IEEE1588 signals.
Software / Operating System (OS)

limits timing resolution and
accuracy! The performance is
system (hardware, OS) dependent.
High-Resolution Timers/Counters
• High Precision Event Timer (HPET) is a 64-bit up-counter with a
frequency higher than 10 MHz.
• Time Stamp Counter (TSC) is a 64-bit register in the CPU (cores)

that increment each processor clock cycle. However, can be unreliable
on a modern multicore computer due to:
– multicore computers can have different values in their time-keeping
registers.
– variability of the CPU frequency due to power management technologies or
performance technologies such as Intel Turbo Boost Technology.
Access the TSC (or HPET) timer using the Windows API functions
QueryPerformanceCounter (μs resolution) and QueryPerformanceFrequency
QueryPerformanceCounter(n) − QueryPerformanceCounter(n − 1)
∆𝑇 =
QueryPerformanceFrequency
Using HPET or TSC ? Not documented …
LabVIEW
Extra
QueryPerformance from LabVIEW
TSC example
TAI and UTC time
• International Atomic Time (TAI) as a time scale is a weighted

average of the time kept by over 300 atomic clocks in over 60
national laboratories worldwide.
• Coordinated Universal Time (UTC) is the primary time

standard by which the world regulates clocks and time, and is
based on TAI but with leap seconds added at irregular intervals
to compensate for the slowing of the Earth's rotation.
• UTC is the time standard used for many internet and World
Wide Web standards. The Network Time Protocol (NTP),
designed to synchronize the clocks of computers over the
Internet, encodes times using the UTC system.
Leap seconds
• Time is now measured using stable atomic clocks
• A leap second is a one-second adjustment that is occasionally

applied to UTC time in order to keep its time of day close to the
mean solar time.
o Solar time is a reckoning of the passage of time based on the Sun's
position in the sky.
• Leap seconds are necessary partly because the length of the

mean solar day is very slowly increasing, and partly because the
atomic, fixed-length SI second, when adopted, was already a little
shorter than the current value of the second of mean solar time.
.
Since 1967, the second has been defined to be the duration of 9,192,631,770
periods of the radiation corresponding to the transition between the two hyperfine
levels of the ground state of the cesium 133 atom
GPS time
• GPS time is the atomic time scale implemented by the atomic clocks
in the GPS ground control stations and the GPS satellites themselves.
• Periodic corrections are performed to the on-board satellite clocks to
keep them synchronized with ground station clocks.
• GPS time is NOT corrected for leap seconds.
• GPS time is NOT equal to UTC or TAI time.
– GPS time is 18 seconds ahead of UTC because of the leap
seconds added to UTC.
– A new leap second correction will be added to UTC in 2021
– GPS time was set to match UTC in 1980
• However, the time offset from UTC is contained in the GPS
broadcast message and is usually applied automatically by GPS
receivers.
From: http://leapsecond.com/java/gpsclock.htm
A GPS satellite clock run faster
(about 38 μs a day) due to
velocity and gravity effects
(follows the Relativity theory)
Time dilation
Time stamping of data
• We often need to timestamp an image in a video stream or a
block of data from a DAQ-card to GPS (UTC) time; e.g. for use
in data fusion in post-analysis.
• If the data samples has a deterministic (regular) interval, such

as samples from a DAQ-card, it is sufficient to time stamp the
first sample at time t0:
𝑡 = 𝑡0 + 𝑛 ∗ ∆𝑡 0 1 2 n
1
∆𝑡 =
𝑓𝑠
• If the data samples are not deterministic (regular), e.g. video

frames from a camera, each data point/video frame must
include a timestamp.
Signal based vs. time-based
synchronization
• Signal-based synchronization involves sharing signals such
as clocks and triggers directly (wires) between nodes that need
to be synchronized.
• Time-based synchronization involves nodes independently
synchronizing their individual clocks based on some time
source, or time reference.
• There are advantages and disadvantages to both methods of
device synchronization.
Synchronization technologies
Signal-based synchronization
• In systems where the devices are near each other, sharing a

common timing signal is generally the easiest and most
accurate method of synchronization.
• To accurately use a common timing signal, a device must be

calibrated to account for the signal propagation delay from the
timing source to the device
Time-based synchronization
• Necessary for long distances
• Because of the inherent instabilities in (crystal oscillator) clocks,

distributed clocks must be synchronized continuously to a time
refererence to match each other in frequency and phase.
• Time references:
– GPS
– IEEE 1588 master
– IRIG-B sources
Global time – possible implementations
Reference clock Reference clock Reference clock
Time Time Δt Time

Time (Time Error)
response request
Computer clock Computer clock Computer clock

IRIG serial time codes
• IRIG = Inter Range Instrumentation Group (a standard)
• Several time codes, but IRIG-B is the most common
• Both AM and DC versions of the code
– Best time accuracy with DC
– AM best for transmission over long cables (so this is most common)
– Accuracies of the order of a few microseconds or better
– Distributed using Coax cable
IRIG-B AM
AM = Amplitude Modulation
BCD = Binary Coded Decimal
IRIG-B DC
GPS with NTP-server and IRIG-B output
Network Time Protocol (NTP)
• NTP is a protocol designed to synchronize the clocks of

computers over a network.
• Can provide accuracies of better than 10 ms over Ethernet.

– accuracy depends on the network (local area network vs. Internet)
• User Datagram Protocol (UDP) is used.
• Beginning with Windows Server 2003 and Windows Vista, a

compliant implementation of full NTP is included.
Precision Time Protocol (PTP)
• The two primary problems that must be overcome in network

timekeeping are oscillator drift and time transfer latency.
• PTP overcomes the Ethernet latency and jitter issues through

hardware time stamping at the physical layer of the network.
– The result can be an accuracy in the 10-nanosecond to 100-
nanosecond range using an Ethernet network to carry the
timing packets
IEEE 1588 Protocol (using hardware)
• Gives sub-microsecond synchronization in distributed
systems.
• IEEE 1588 provides a standard protocol for synchronizing

clocks connected via a multicast capable network, such as
Ethernet.
– uses the precision time protocol (PTP).
– eliminates the need for additional cabling.
• All participating clocks in the network are synchronized to the

highest quality clock in the network.
• The highest ranking clock is called the grandmaster clock, and

synchronizes all other slave clocks.
IEEE 1588 example for sensor DAQ
• Consider the example of a real-time control system that is set
up over Ethernet with a variety of independent sensors.
• Each sensor uses an onboard 1588 clock slaved to a
grandmaster clock and is synchronized with the other sensors
on the network to an accuracy of 1 microsecond.
• Every 5 milliseconds, each sensor takes a measurement and
sends the information back to the controller, using the same
LAN that is coordinating the synchronization of the sensors.
•  data is acquired synchronously from the entire system at
precise time intervals.
Example from Microsemi_IEEE_1588_PTP_New_Standard_in_Time_Synchronization_White_Paper.pdf

Windows 10 support PTP
• Windows used to be a bad time keeper!
• From Windows 10 PTP is supported in Windows.

– Hardware master and software (Windows) client.
• Allows a clock accuracy of about 1 ms.

– However, a setup of PTP is required in Windows 10!
– Or, use a third party software.
Comparison
Figure from Microsemi_IEEE_1588_PTP_New_Standard_in_Time_Synchronization_White_Paper.pdf

Example - Vision time stamping
Must avoid “software in the
loop” to achieve the best
possible time accuracy and
Camera
resolution !
Remember: Data buffers both
in camera and in computer
RAM!
Ethernet PC SW
Loop time stamp is
not equal to image
sample time!
NIC

l12 - Time and Synchronization v22

Uploaded by

Copyright:

Available Formats

l12 - Time and Synchronization v22

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

l12 - Time and Synchronization v22

Uploaded by

Copyright:

Available Formats

FYS3240- 4240

Data acquisition & control

Time and synchronization

Spring 2022– Lecture #12

TU-artikkel : GPS mer enn bare navigasjon

• Depends on the application.

• If the clock in the GPS receiver have an error of 1 ms relative to

På rett sted til rett tid (regjeringen.no)

• Watch crystal oscillator: about 20 ppm, or worse

• The accuracy can be improved using a:

• Some DAQ card accuracy examples:

• Example: Microsemi CSAC

Software / Operating System (OS)

• Time Stamp Counter (TSC) is a 64-bit register in the CPU (cores)

• International Atomic Time (TAI) as a time scale is a weighted

• Coordinated Universal Time (UTC) is the primary time

• A leap second is a one-second adjustment that is occasionally

• Leap seconds are necessary partly because the length of the

• If the data samples has a deterministic (regular) interval, such

• If the data samples are not deterministic (regular), e.g. video

• In systems where the devices are near each other, sharing a

• To accurately use a common timing signal, a device must be

• Because of the inherent instabilities in (crystal oscillator) clocks,

Reference clock Reference clock Reference clock

Time Time Δt Time

Computer clock Computer clock Computer clock

Network Time Protocol (NTP)

• NTP is a protocol designed to synchronize the clocks of

• Can provide accuracies of better than 10 ms over Ethernet.

• User Datagram Protocol (UDP) is used.

• Beginning with Windows Server 2003 and Windows Vista, a

• The two primary problems that must be overcome in network

• PTP overcomes the Ethernet latency and jitter issues through

• IEEE 1588 provides a standard protocol for synchronizing

• All participating clocks in the network are synchronized to the

• The highest ranking clock is called the grandmaster clock, and

Example from Microsemi_IEEE_1588_PTP_New_Standard_in_Time_Synchronization_White_Paper.pdf

• Windows used to be a bad time keeper!

• From Windows 10 PTP is supported in Windows.

• Allows a clock accuracy of about 1 ms.

Figure from Microsemi_IEEE_1588_PTP_New_Standard_in_Time_Synchronization_White_Paper.pdf

You might also like